Results for “Direct integration approach” — Page 31

NASA NTRS1989

Structural stability augmentation system design using BODEDIRECT: A quick and accurate approach

A methodology is presented for a modal suppression control law design using flight test data instead of mathematical models to obtain the required gain and phase information about the flexible airplane. This approach is referred to as BODEDIRECT. The purpose of the BODEDIRECT program is to provide a method of analyzing the modal phase relationships measured directly from the airplane. These measurements can be achieved with a frequency sweep at the control surface input while measuring the outputs of interest. The measured Bode-models can be used directly for analysis in the frequency domain, and for control law design. Besides providing a more accurate representation for the system inputs and outputs of interest, this method is quick and relatively inexpensive. To date, the BODEDIRECT program has been tested and verified for computational integrity. Its capabilities include calculation of series, parallel and loop closure connections between Bode-model representations. System PSD, together with gain and phase margins of stability may be calculated for successive loop closures of multi-input/multi-output systems. Current plans include extensive flight testing to obtain a Bode-model representation of a commercial aircraft for design of a structural stability augmentation system.

Goslin, T. J.↗

NASA NTRS1999

Water Flow Performance of a Superscale Model of the Fastrac Liquid Oxygen Pump

As part of the National Aeronautics and Space Administration's ongoing effort to lower the cost of access to space, the Marshall Space Flight Center has developed a rocket engine with 60,000 pounds of thrust for use on the Reusable Launch Vehicle technology demonstrator slated for launch in 2000. This gas generator cycle engine, known as the Fastrac engine, uses liquid oxygen and RP-1 for propellants and includes single stage liquid oxygen and RP-1 pumps and a single stage supersonic turbine on a common shaft. The turbopump design effort included the first use and application of new suction capability prediction codes and three-dimensional blade generation codes in an attempt to reduce the turbomachinery design and certification costs typically associated with rocket engine development. To verify the pump's predicted cavitation performance, a water flow test of a superscale model of the Fastrac liquid oxygen pump was conducted to experimentally evaluate the liquid oxygen pump's performance at and around the design point. The water flow test article replicated the flow path of the Fastrac liquid oxygen pump in a 1.582x scale model, including scaled seal clearances for correct leakage flow at a model operating speed of 5000 revolutions per minute. Flow entered the 3-blade axial-flow inducer, transitioned to a shrouded, 6-blade radial impeller, and discharged into a vaneless radial diffuser and collection volute. The test article included approximately 50 total and static pressure measurement locations as well as flush-mounted, high frequency pressure transducers for complete mapping of the pressure environment. The primary objectives of the water flow test were to measure the steady-state and dynamic pressure environment of the liquid oxygen pump versus flow coefficient, suction specific speed, and back face leakage flow rate. Results showed excellent correlation between the predicted and experimentally measured pump head rise at low suction specific speeds. Likewise, only small circumferential variations in steady-state impeller exit and radial diffuser pressure distributions were observed from 80% to 120% of the design flow coefficient, matching the computational predictions and confirming that the integrated design approach has minimized any exit volute-induced distortions. The test article exhibited suction performance trends typically observed in inducer designs with virtually constant head rise with decreasing inlet pressure until complete pump head breakdown. Unfortunately, the net positive suction head at 3% head fall-off occurred far below that predicted at all tested flow coefficients, resulting in a negative net positive suction head margin at the design point in water. Additional testing to map the unsteady pressure environment was conducted and interesting rotating phenomena at the inducer inlet were observed. These rotating phenomena's cell numbers, direction, and speed were correlated with pump operating parameters. The impact of the unsteady phenomena and their corresponding energy losses on the unexpectedly poor pump performance is also discussed.

Skelley, Stephen↗

NASA NTRSDate not supplied

Biological Research and Space Health Enabled by Machine Learning to Support Deep Space Missions

A key science goal of the NASA “Moon to Mars” campaign is to understand how biology responds to the Lunar, Martian, and deep space environments in order to advance fundamental knowledge, reduce risk, and support safe, productive human space missions. Through the powerful emerging computer science approaches of artificial intelligence (AI) and machine learning (ML), a paradigm shift has begun in biomedical science and engineered astronaut health systems, to enable Earth-independence and autonomy of mission operations. We present a decadal view of AI/ML architecture to support deep space mission goals, developed in concert with leaders in the field. We describe current AI/ML methods to support 1) fundamental biology, 2) in situ analytics, 3) high performance computing hardware, 4) automated science, 5) self-driving labs, 6) remote data management, 7) integrated real-time mission biomonitoring, and 8) a Precision Space Health system. Cutting-edge AI/ML approaches that can be integrated to support these domains include active learning, explainable AI, adaptive learning, causal inference, knowledge graphs, federated learning, transfer learning, and large language models. Finally, we present results from several current ML projects that are underway in the field to address key challenges of small sample n, high feature count, heterogeneity, and sparse data. These include 1) connecting omics data to phenotypic data using an ensemble model to infer causality of spaceflight rodent liver health disruption, 2) usage of explainable ML to interrogate the muscular underpinnings of spaceflight muscle atrophy, 3) ML models analyzing and determining directed acyclic graphs of human space health risk leveraging rodent bone datasets, 4) usage of large pre-trained models connecting biomedical knowledgebases with small spaceflight datasets to understand gene-to-gene interaction networks, and 5) a suite of benchmarked open science datasets (spaceflight mouse liver; radiation DNA damage) enabling programmers to identify the best ML algorithms to answer space biological science questions.

space biology↗

NASA NTRSDate not supplied

Control System Development for A Zero Boil-Off Hydrogen Storage Demonstration With Two-Stage Active Cooling

A NASA team is designing and building a test article to demonstrate the long duration storage of liquid hydrogen via active cooling (cryocoolers) while implementing a two-stage cooling approach. This activity is one of a large portfolio of NASA’s Space Technology Mission Directorate funded activities which focuses on the technology maturation needed for long duration storage of cryogenic liquid in-space. The current state-of-the-art for liquid hydrogen storage on-orbit is on the order of hours while NASA’s planned missions require storage for months, or even years. To enable such a long duration, Zero Boil-Off conditions must be achieved which requires passive technologies to minimize environmental heat loads, but also active cooling to intercept and reject the remaining heat to deep space. The implementation of active cooling results in a significant amount of dry mass added to the vehicle. Utilizing a Two-Stage Cooling approach, analysis and testing to date indicates the Zero Boil-Off of liquid hydrogen can be achieved with less mass and electrical power relative to a single-stage cooling approach where only one cryocooler is used. This activity will demonstrate the fully integrated suite of technologies needed to enable the Two-Stage Cooling approach which includes Multi-Layer Insulation blankets, Low Conductivity Structures, a Tube-On-Tank Heat Exchanger, Tube-On-Shield Heat Exchanger and a Two-Stage Cryogenerator (both 90 Kelvin and 20 Kelvin) with each stage having an independently controlled circulation loop. The bulk of the heat load is intercepted by the 90 Kelvin loop via a thin foil heat exchanger internal to the insulation blankets (also known as a Broad Area Cooling Shield), with the remainder removed at cryofluid temperature (20 Kelvin) by tubes directly welded to the outer tank surface. In this paper, we examine the challenges of controlling the system, and describe the development of control algorithms and software for future testing with liquid hydrogen. The interactions between the cryofans which control circulation loop mass flow rates, electrical heaters which vary the cryocooler lift to simulate the operation of variable-lift flight units, tank heaters which can vary the overall heat load, and the effects of changes in circulation loop pressure as temperatures change, can be complex and must be well understood to maintain steady-state propellant conditions and achieve Zero Boil-Off. Parallel PID loops and watchdog programs implemented on the user interface system will help bring the systems to steady state operation and keep them at selected operating points within acceptable error, while avoiding runaway feedback loops.

cryogenics↗

NASA NTRSDate not supplied

Biological Research and Space Health Enabled by Machine Learning to Support Deep Space Missions

A key science goal of the NASA “Moon to Mars” campaign is to understand how biology responds to the Lunar, Martian, and deep space environments in order to advance fundamental knowledge, reduce risk, and support safe, productive human space missions. Through the powerful emerging computer science approaches of artificial intelligence (AI) and machine learning (ML), a paradigm shift has begun in biomedical science and engineered astronaut health systems, to enable Earth-independence and autonomy of mission operations. We present a decadal view of AI/ML architecture to support deep space mission goals, developed in concert with leaders in the field. We describe current AI/ML methods to support 1) fundamental biology, 2) in situ analytics, 3) high performance computing hardware, 4) automated science, 5) self-driving labs, 6) remote data management, 7) integrated real-time mission biomonitoring, and 8) a Precision Space Health system. Cutting-edge AI/ML approaches that can be integrated to support these domains include active learning, explainable AI, adaptive learning, causal inference, knowledge graphs, federated learning, transfer learning, and large language models. Finally, we present results from several current ML projects that are underway in the field to address key challenges of small sample n, high feature count, heterogeneity, and sparse data. These include 1) connecting omics data to phenotypic data using an ensemble model to infer causality of spaceflight rodent liver health disruption, 2) usage of explainable ML to interrogate the muscular underpinnings of spaceflight muscle atrophy, 3) ML models analyzing and determining directed acyclic graphs of human space health risk leveraging rodent bone datasets, 4) usage of large pre-trained models connecting biomedical knowledgebases with small spaceflight datasets to understand gene-to-gene interaction networks, and 5) a suite of benchmarked open science datasets (spaceflight mouse liver; radiation DNA damage) enabling programmers to identify the best ML algorithms to answer space biological science questions.

space biology↗

NASA NTRSDate not supplied

Supportability Concepts for Crewed Deep Space Exploration

Supportability—defined as the set of system characteristics that influence the logistics and support required to enable safe and effective operations—will be a much larger driver of mass, risk, and crew time for future human space exploration due to the more challenging mission context. For Mars, systems must operate in a logistically isolated environment for much longer durations than previous missions, which results in a higher probability of system failure and therefore an increased need for maintenance or contingency options. Mars missions also lack access to quick aborts, which increases the consequences of an unrecoverable system failure. Together, this higher likelihood and consequence of failure results in an increase in supportability-related risk. Supportability analysis is an important part of systems development that helps designers better understand the impacts of system and mission decisions on risk, mass, and crew time. The real-world processes that drive maintenance requirements and other supportability-related characteristics are probabilistic, and therefore they require different conceptual approaches and models than are used for more deterministic aspects of space systems. This paper provides an overview of supportability analysis, addresses key concepts, and provides examples of how supportability analysis can be incorporated into system development. Specifically, system supportability involves stochastic processes, and therefore must be evaluated using probabilistic models. These models can be used to perform sensitivity analysis even if system characteristics are not yet fully defined. Failure rates cannot be measured directly, but tests provide valuable data that can help refine those estimates. Human spaceflight architectures are complex, and exhibit coupled behavior that should be examined with integrated systems analysis that includes an assessment of supportability.

Supportability↗

NASA NTRSDate not supplied

Supportability Concepts for Crewed Deep Space Exploration

Supportability—defined as the set of system characteristics that influence the logistics and support required to enable safe and effective operations—will be a much larger driver of mass, risk, and crew time for future human space exploration due to the more challenging mission context. For Mars, systems must operate in a logistically isolated environment for much longer durations than previous missions, which results in a higher probability of system failure and therefore an increased need for maintenance or contingency options. Mars missions also lack access to quick aborts, which increases the consequences of an unrecoverable system failure. Together, this higher likelihood and consequence of failure results in an increase in supportability-related risk. Supportability analysis is an important part of systems development that helps designers better understand the impacts of system and mission decisions on risk, mass, and crew time. The real-world processes that drive maintenance requirements and other supportability-related characteristics are probabilistic, and therefore they require different conceptual approaches and models than are used for more deterministic aspects of space systems. This paper provides an overview of supportability analysis, addresses key concepts, and provides examples of how supportability analysis can be incorporated into system development. Specifically, system supportability involves stochastic processes, and therefore must be evaluated using probabilistic models. These models can be used to perform sensitivity analysis even if system characteristics are not yet fully defined. Failure rates cannot be measured directly, but tests provide valuable data that can help refine those estimates. Human spaceflight architectures are complex, and exhibit coupled behavior that should be examined with integrated systems analysis that includes an assessment of supportability.

Supportability↗

NASA NTRS1993

Measurement of p-mode energy propagation in the quiet solar photosphere

We have measured and analyzed the p-mode oscillations in the profile of the Mg I 4571 A line in a quiet region near disk center. The oscillations are found to be mostly standing waves, in agreement with previous work. However, a small propagating component is measured, and we determine the direction, magnitude, and vertical variation of the energy propagation. The work integral indicates an upward energy flow of about 2 x 10 exp 7 ergs/sq cm/s at a height of 50 km above the base of the photosphere for waves with frequencies of 2-16 mHz. This energy flow decreases exponentially with height and drops below 10 exp 5 ergs/sq cm/s in the uppermost photosphere. The energy flow leaving the upper photosphere is at least an order of magnitude too small to constitute a significant source of heating for the chromosphere. However, the p-mode damping in the lower photosphere approaches levels large enough to account for the measured p-mode line widths. The relative amplitudes and phases of the thermodynamic quantities indicate that the p-mode are neither adiabatic nor isothermal in the photosphere.

Fontenla, J. M.↗

NASA NTRS2008

Lunar Communication Terminals for NASA Exploration Missions: Needs, Operations Concepts and Architectures

NASA is conducting architecture studies prior to deploying a series of short- and long-duration human and robotic missions for the exploration of the Moon and Mars under the Vision for Space Exploration Initiative. A key objective of these missions is to establish and expand, through a series of launches, a system of systems approach to exploration capabilities and science return. The systems identified were Crew Exploration Vehicles, crew and cargo launch vehicles, crew EVA suits, crew and cargo landers, habitats, mobility carriers, and small, pressurized rovers. Multiple space communication networks and systems, deployed over time, will support these space exploration systems of systems. Each deployment phase will support interoperability of components and provide 20 years of legacy systems. In this paper, we describe the modular lunar communications terminals needed for the emerging lunar mission operational scenarios. These lunar communication terminals require flexibility for use in stationary, integrated, and mobile environments. They will support links directly to Earth, to lunar relay satellites, to astronauts and to fixed and mobile lunar surface systems. The operating concepts and traffic models are presented for these terminals within variety of lunar scenarios. A preliminary architecture is outlined, providing for suitable long-duration operations in the harsh lunar environment.

Bhasin, Kul B.↗

NASA NTRS2008

Automatic Testcase Generation for Flight Software

The TacSat3 project is applying Integrated Systems Health Management (ISHM) technologies to an Air Force spacecraft for operational evaluation in space. The experiment will demonstrate the effectiveness and cost of ISHM and vehicle systems management (VSM) technologies through onboard operation for extended periods. We present two approaches to automatic testcase generation for ISHM: 1) A blackbox approach that views the system as a blackbox, and uses a grammar-based specification of the system's inputs to automatically generate *all* inputs that satisfy the specifications (up to prespecified limits); these inputs are then used to exercise the system. 2) A whitebox approach that performs analysis and testcase generation directly on a representation of the internal behaviour of the system under test. The enabling technologies for both these approaches are model checking and symbolic execution, as implemented in the Ames' Java PathFinder (JPF) tool suite. Model checking is an automated technique for software verification. Unlike simulation and testing which check only some of the system executions and therefore may miss errors, model checking exhaustively explores all possible executions. Symbolic execution evaluates programs with symbolic rather than concrete values and represents variable values as symbolic expressions. We are applying the blackbox approach to generating input scripts for the Spacecraft Command Language (SCL) from Interface and Control Systems. SCL is an embedded interpreter for controlling spacecraft systems. TacSat3 will be using SCL as the controller for its ISHM systems. We translated the SCL grammar into a program that outputs scripts conforming to the grammars. Running JPF on this program generates all legal input scripts up to a prespecified size. Script generation can also be targeted to specific parts of the grammar of interest to the developers. These scripts are then fed to the SCL Executive. ICS's in-house coverage tools will be run to measure code coverage. Because the scripts exercise all parts of the grammar, we expect them to provide high code coverage. This blackbox approach is suitable for systems for which we do not have access to the source code. We are applying whitebox test generation to the Spacecraft Health INference Engine (SHINE) that is part of the ISHM system. In TacSat3, SHINE will execute an on-board knowledge base for fault detection and diagnosis. SHINE converts its knowledge base into optimized C code which runs onboard TacSat3. SHINE can translate its rules into an intermediate representation (Java) suitable for analysis with JPF. JPF will analyze SHINE's Java output using symbolic execution, producing testcases that can provide either complete or directed coverage of the code. Automatically generated test suites can provide full code coverage and be quickly regenerated when code changes. Because our tools analyze executable code, they fully cover the delivered code, not just models of the code. This approach also provides a way to generate tests that exercise specific sections of code under specific preconditions. This capability gives us more focused testing of specific sections of code.

Bushnell, David Henry↗

NASA NTRS1993

A decision-theoretic approach to the display of information for time-critical decisions: The Vista project

We describe a collaborative research and development effort between the Palo Alto Laboratory of the Rockwell Science Center, Rockwell Space Operations Company, and the Propulsion Systems Section of NASA JSC to design computational tools that can manage the complexity of information displayed to human operators in high-stakes, time-critical decision contexts. We shall review an application from NASA Mission Control and describe how we integrated a probabilistic diagnostic model and a time-dependent utility model, with techniques for managing the complexity of computer displays. Then, we shall describe the behavior of VPROP, a system constructed to demonstrate promising display-management techniques. Finally, we shall describe our current research directions on the Vista 2 follow-on project.

Horvitz, Eric↗

NASA NTRS1981

The CELSS program - An overview of its structure and use of computer modelling

NASA has initiated a research program, CELSS, directed at the acquisition of the knowledge and technology required for the development of an autonomous, regenerative life support system. The program is structured to promote effective, cooperative research in fundamental, applied and engineering science. The initial research thrusts involve investigations into problems of food production, waste processing and system control and integration. In the area of food production both conventional, higher plant-based processes as well as chemosynthetic food production technologies are being investigated. Alternative waste processing procedures, both biological and physicochemical, are being examined. Computer based modelling as an aid to design and analysis is an integral part of the approach to system control and management. A mass balance model depicting the flow of elemental mass in a conceptualized closed, regenerative life support system is described.

Averner, M. M.↗

NASA NTRS1993

A modified approach to controller partitioning

The idea of computing a decentralized control law for the integrated flight/propulsion control of an aircraft by partitioning a given centralized controller is investigated. An existing controller partitioning methodology is described, and a modified approach is proposed with the objective of simplifying the associated controller approximation problem. Under the existing approach, the decentralized control structure is a variable in the partitioning process; by contrast, the modified approach assumes that the structure is fixed a priori. Hence, the centralized controller design may take the decentralized control structure into account. Specifically, the centralized controller may be designed to include all the same inputs and outputs as the decentralized controller; then, the two controllers may be compared directly, simplifying the partitioning process considerably. Following the modified approach, a centralized controller is designed for an example aircraft mode. The design includes all the inputs and outputs to be used in a specified decentralized control structure. However, it is shown that the resulting centralized controller is not well suited for approximation by a decentralized controller of the given structure. The results indicate that it is not practical in general to cast the controller partitioning problem as a direct controller approximation problem.

Garg, Sanjay↗

NASA NTRS1997

On spurious behavior of CFD simulations

Spurious behavior in underresolved grids and/or semi-implicit temporal discretizations for four computational fluid dynamics (CFD) simulations are studied. The numerical simulations consist of (a) a 1-D chemically relaxed nonequilibrium model, (b) the direct numerical simulation (DNS) of 2-D incompressible flow over a backward facing step, (c) a loosely-coupled approach for a 2-D fluid-structure interaction, and (d) a 3-D compressible unsteady flow simulation of vortex breakdown in delta wings. Using knowledge from dynamical systems theory, various types of spurious behaviors that are numerical artifacts were systematically identified. These studies revealed the various possible dangers of misinterpreting numerical simulation of realistic complex flows that are constrained by the available computing power. In large scale computations underresolved grids, semi-implicit procedures, loosely-coupled implicit procedures, and insufficiently long time integration in DNS are most often unavoidable. Consequently, care must be taken in both computation and in interpretation of the numerical data. The results presented confirm the important role that dynamical systems theory can play in the understanding of the nonlinear behavior of numerical algorithms and in aiding the identification of the sources of numerical uncertainties in CFD.

Numerical Solution↗

NASA NTRS2000

Towards LES Models of Jets and Plumes

As pointed out by Rodi standard integral solutions for jets and plumes developed for discharge into infinite, quiescent ambient are difficult to extend to complex situations, particularly in the presence of boundaries such as the sea floor or ocean surface. In such cases the assumption of similarity breaks down and it is impossible to find a suitable entrainment coefficient. The models are also incapable of describing any but the most slowly varying unsteady motions. There is therefore a need for full time-dependent modeling of the flow field for which there are three main approaches: (1) Reynolds averaged numerical simulation (RANS), (2) large eddy simulation (LES), and (3) direct numerical simulation (DNS). Rodi applied RANS modeling to both jets and plumes with considerable success, the test being a match with experimental data for time-averaged velocity and temperature profiles as well as turbulent kinetic energy and rms axial turbulent velocity fluctuations. This model still relies on empirical constants, some eleven in the case of the buoyant jet, and so would not be applicable to a partly laminar plume, may have limited use in the presence of boundaries, and would also be unsuitable if one is after details of the unsteady component of the flow (the turbulent eddies). At the other end of the scale DNS modeling includes all motions down to the viscous scales. Boersma et al. have built such a model for the non-buoyant case which also compares well with measured data for mean and turbulent velocity components. The model demonstrates its versatility by application to a laminar flow case. As its name implies, DNS directly models the Navier-Stokes equations without recourse to subgrid modeling so for flows with a broad spectrum of motions (high Re) the cost can be prohibitive - the number of required grid points scaling with Re(exp 9/4) and the number of time steps with Re(exp 3/4). The middle road is provided by LES whereby the Navier-Stokes equations are formally filtered with the filter chosen to only exclude the smallest turbulent motions. If successful, LES should provide much of the detail available to DNS but at more bearable cost. Fatica et al. in comparing LES with DNS for a low Reynolds number jet showed that the LES could simulate the temporally evolving behavior including growth of the jet thickness. It is the intention of this report to explore the application of an LES model to jets and plumes. As always, before tackling complex situations, the model must be tested for the simplest of cases and so we address only two, a non-buoyant axisymmetric jet issuing steadily from an orifice into a semi-infinite stationary environment and a buoyant jet in the same environment. The work is a continuation of Basu and Mansour.

Webb, A. T.↗

NASA NTRS2019

Additive Manufacturing of Multi-Material Systems for Aerospace Applications

Additive manufacturing methods for producing single materials are rapidly improving. The resulting material properties and microstructures are becoming more comparable to those of conventionally fabricated materials. However, the need for multi-functional and complex structures and components requires additional innovations in manufacturing such as multi-material and hybrid additive manufacturing approaches. Additive manufacturing machines with multiple print capabilities and combinations of AM, machining, and conventional processing methods will further open up design spaces and possibilities. In this presentation, several examples of the needs and methods for multi-material fabrication will be discussed with a focus on aerospace applications. Direct printing of silver coils in conjunction with fused deposition modeling, machined parts, and, binder jetting is being developed for innovative stator designs. Binder jetting of silicon-based materials with powder bed additions is being developed for heat exchanger applications. Additive manufacturing of bi-material systems is being pursued to fabricate lightweight, integrated, multifunctional structures.

multi-materials↗

NASA NTRS1991

A special purpose silicon compiler for designing supercomputing VLSI systems

Design of general/special purpose supercomputing VLSI systems for numeric algorithm execution involves tackling two important aspects, namely their computational and communication complexities. Development of software tools for designing such systems itself becomes complex. Hence a novel design methodology has to be developed. For designing such complex systems a special purpose silicon compiler is needed in which: the computational and communicational structures of different numeric algorithms should be taken into account to simplify the silicon compiler design, the approach is macrocell based, and the software tools at different levels (algorithm down to the VLSI circuit layout) should get integrated. In this paper a special purpose silicon (SPS) compiler based on PACUBE macrocell VLSI arrays for designing supercomputing VLSI systems is presented. It is shown that turn-around time and silicon real estate get reduced over the silicon compilers based on PLA's, SLA's, and gate arrays. The first two silicon compiler characteristics mentioned above enable the SPS compiler to perform systolic mapping (at the macrocell level) of algorithms whose computational structures are of GIPOP (generalized inner product outer product) form. Direct systolic mapping on PLA's, SLA's, and gate arrays is very difficult as they are micro-cell based. A novel GIPOP processor is under development using this special purpose silicon compiler.

Venkateswaran, N.↗

NASA NTRS1987

Investigation of turbulent shear flows by numerical simulation

A data base (Kim et al., 1986) generated by direct numerical integration of the Navier-Stokes equations for unsteady three-dimensional turbulent channel flow at low Reynolds numbers is applied to investigate the physical processes acting in wall-bounded shear flows. The techniques used to construct the data base are outlined; the modeling of turbulence, streaks and streamwise vortices, horseshoe and inverted-horseshoe vortices, and vortex rings is described; the conditional sampling techniques employed are discussed; and typical results are presented graphically. An organized vorticity-field structure is revealed and found to be associated with the bursting process and a local peak in the wall pressure, indicating a possible approach to reducing viscous drag.

Kim, J.↗