Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Coarse graining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Submarine landslides triggered by destabilization of high-saturation hydrate anomalies: LANDSLIDES CAUSED BY HYDRATE ANOMALIES

Submarine landslides occur along continental margins at depths that often intersect the gas hydrate stability zone, prompting suggestions that slope stability may be affected by perturbations that arise from changes in hydrate stability. Here we develop a numerical model to identify the conditions under which the destabilization of hydrates results in slope failure. Specifically, we focus on high-saturation hydrate anomalies at fine-grained to coarse-grained stratigraphic boundaries that can transmit bridging stresses that decrease the effective stress at sediment contacts and disrupt normal sediment consolidation. We evaluate slope stability before and after hydrate destabilization. Hydrate anomalies act to significantly increase the overall slope stability due to large increases in effective cohesion. However, when hydrate anomalies destabilize there is a loss of cohesion and increase in effective stress that causes the sediment grains to rapidly consolidate and generate pore pressures that can either trigger immediate slope failure or weaken the surrounding sediment until the pore pressure diffuses away. In cases where failure does not occur, the sediment can remain weakened for months. In cases where failure does occur, we quantify landslide dynamics using a rate and state frictional model and find that landslides can display either slow or dynamic (i.e., catastrophic) motion depending on the rate-dependent properties, size of the stress perturbation, and the size of the slip patch relative to a critical nucleation length scale. Our results illustrate the fundamental mechanisms through which the destabilization of gas hydrates can pose a significant geohazard.

58 GEOSCIENCES↗

High‐Temperature Mechanical Behavior of Single‐Crystal FeCrAl Alloy Under In Situ Micropillar Compression

FeCrAl cladding is one of the candidate materials for the near‐term accident‐tolerant fuel technologies under development. Research on high‐temperature mechanical behaviors of single‐crystal FeCrAl alloy is rather limited. Previous studies have reported the mechanical property of low‐index orientation in single‐crystal FeCrAl alloy at room temperature. However, the critical resolved shear stress to activate slip systems can be orientation and temperature dependent. Here, single‐crystal grains in a coarse‐grained FeCrAl alloy with different crystallographic orientations are selected to preferentially activate {110}<111> slip systems or {112}<111> slip systems. Micropillars are fabricated in the selected single‐crystal grains and tested at elevated temperatures in situ in a scanning electron microscope. The critical resolved shear stresses of {110}<111> slip systems and {112}<111> slip systems are determined at various temperatures. The critical resolved shear stress shows a temperature dependence and orientation independence. This study provides important insight for understanding the deformation mechanisms of FeCrAl alloys at elevated temperatures.

Sun, Tianyi↗

Powder Metallurgy HIP Process Study and Mechanical Property Evaluations for IN740H

The effects of hot isostatic pressing (HIP) parameters and powder size distribution (PSD) on the resulting microstructure and properties of powder metallurgy (P/M) IN740H have been investigated. Properties can be substantially tailored through the appropriate management of these parameters. Applying a thermal presoak to the input powder prior to the sintering stage of HIP can significantly increase average grain size and coarse grain fraction, enabling a trade for improved creep resistance at the expense of tensile strength. Here, powder thermal presoak was found to have a larger impact on microstructure and properties than the use of a coarser PSD alone. Additionally, substantial grain growth and grain boundary migration is observed in P/M IN740H at HIP temperatures above 1260°C. Given its inherently finer grain size, P/M HIP IN740H typically outperforms its cast and wrought counterparts in tensile response. Creep life at 700–800°C was inferior to wrought due to PPBs coincident with grain boundaries which served as cavity nucleation sites, leading to lower creep ductility. The ability to adjust the microstructure toward a more balanced creep and tensile behavior allows P/M HIP IN740H to be considered for high-temperature applications in advanced ultra-supercritical steam and supercritical carbon dioxide power cycles.

36 MATERIALS SCIENCE↗

Metal/ceramic interface structures and segregation behavior in aluminum-based composites

Trimodal Al alloy (AA) matrix composites consisting of ultrafine-­grained (UFG) and coarse-­ grained (CG) Al phases and micron-­sized B 4 C ceramic reinforcement particles exhibit combinations of strength and ductility that render them useful for potential applications in the aerospace, defense and automotive industries. Tailoring of microstructures with specific mechanical properties requires a detailed understanding of interfacial structures to enable strong interface bonding between ceramic reinforcement and metal matrix, and thereby allow for effective load transfer. Trimodal AA metal matrix composites typically show three characteristics that are noteworthy: nanocrystalline grains in the vicinity of the B4C reinforcement particles; Mg segregation at AA/B 4 C interfaces; and the presence of amorphous interfacial layers separating nanocrystalline grains from B 4 C particles. Interestingly, however, fundamental information related to the mechanisms responsible for these characteristics as well as information on local compositions and phases are absent in the current literature. Here in this study, we use high-­resolution transmission electron microscopy, energy-­dispersive X-­ray spectroscopy, electron energy-­loss spectroscopy, and precession assisted electron diffraction to gain fundamental insight into the mechanisms that affect the characteristics of AA/B 4 C interfaces. Specifically, we determined interfacial structures, local composition and spatial distribution of the interfacial constituents. Near atomic resolution characterization revealed amorphous multilayers and a nanocrystalline region between Al phase and B 4 C reinforcement particles. The amorphous multilayers consist of nonstoichiometric Al x O y , while the nanocrystalline region is comprised of MgO nanograins. The experimental results are discussed in terms of the possible underlying mechanisms at AA/B 4 C interfaces.

36 MATERIALS SCIENCE↗

Effect of grain refinement on high temperature steam oxidation of an FeCrAl alloy

FeCrAl alloys are promising candidates to replace Zr alloys as fuel cladding materials in nuclear light-water reactors. Grain refinement has been indicated to improve irradiation resistance. To enhance corrosion resistance as well, the effects of grain refinement on steam corrosion behavior were investigated in this work. Samples of Kanthal D alloy (Fe-21Cr-5Al) with two different grain sizes (coarse-grained and ultrafine-grained) were exposed to steam at 1200 °C for 2 hrs. In conclusion, results indicate improved steam corrosion resistance in ultrafine-grained Kanthal D with formation of a thinner protective Al oxide layer and the presence of a thin underlying Cr oxide layer.

36 MATERIALS SCIENCE↗

The characterisation of lead-free thick-film resistors on different low temperature Co-fired ceramics substrates

Graphical abstract: Display Omitted Highlights: ► Lead free thick film resistors based on ruthenium oxide were developed. ► The compatibility of resistors with different LTCC substrates was evaluated. ► The interactions between resistors and glassy LTCC substrates were not detected. ► Electrical characteristics were comparable with commercial thick film resistors. -- Abstract: Lead-free thick-film resistors were synthesised and investigated. The thick-film resistor materials with nominal sheet resistivities from 50 ohm/sq. to 50 kohm/sq. were prepared using combinations of two lead-free glasses with reflow temperatures at 940 °C and 1240 °C, respectively, and two RuO{sub 2} powders (fine-grained and coarse-grained RuO{sub 2}). The thick-film resistors were printed and fired on alumina and on low temperature co-fired ceramics substrates and fired at 850 °C and 950 °C. The fired resistors were investigated by X-ray powder diffraction, by scanning electron microscopy and by energy dispersive X-ray analysis. The sheet resistivities, temperature coefficients of resistivity, gauge factors and noise indices were measured.

36 MATERIALS SCIENCE↗

Parallel phase model : a programming model for high-end parallel machines with manycores.

This paper presents a parallel programming model, Parallel Phase Model (PPM), for next-generation high-end parallel machines based on a distributed memory architecture consisting of a networked cluster of nodes with a large number of cores on each node. PPM has a unified high-level programming abstraction that facilitates the design and implementation of parallel algorithms to exploit both the parallelism of the many cores and the parallelism at the cluster level. The programming abstraction will be suitable for expressing both fine-grained and coarse-grained parallelism. It includes a few high-level parallel programming language constructs that can be added as an extension to an existing (sequential or parallel) programming language such as C; and the implementation of PPM also includes a light-weight runtime library that runs on top of an existing network communication software layer (e.g. MPI). Design philosophy of PPM and details of the programming abstraction are also presented. Several unstructured applications that inherently require high-volume random fine-grained data accesses have been implemented in PPM with very promising results.

99 GENERAL AND MISCELLANEOUS↗

Petrology of EETA79006 and implications for the formation of polymict eucrites

A newly found polymict eucrite, EETA79006, is described. Lithic clasts are similar to those found in howardites and fall into four groups: fine-grained (aphanitic), coarse-grained, basaltic, and cataclastic. All have eucritic compositions and differ mainly in cooling and deformation histories. Some basaltic clasts cooled faster than others and may be impact melts. Analysis of pyroxene and feldspar in the matrix and in 20 lithic clasts indicates that the matrix was not derived from the observed lithic clast population. This meteorite and similar polymict eucrites may have formed by addition of younger more fractionated lithic clasts to the regolith of the parent body.

Simon, S. B.↗

Spectral Behavior of Hematite at Visible/Near Infrared and Midinfrared Wavelengths

The oxide mineral hematite alpha-Fe2O3) is present on Mars as evidenced by spectroscopy using visible/near infrared (VNIR) and midinfrared (MIR) wavelengths. The physical nature of this surficial hematite varies from fine-grained, crystalline red hematite (red-Hm) in certain martian bright regions, to coarser-grained, crystalline gray hematite (gray-Hm) in the Sinus Meridiani equatorial site discovered in the Mars Global Surveyor Thermal Emission Spectrometer (MGS-TES) data. The VNIR spectra require that the red hematite is present in amounts subordinate to a second ferric pigment, which accounts for the general shape and position of the martian ferric absorption edge. By analogy with palagonitic tephra and synthetic samples, the pigment is a nanophase ferric oxide, possibly nanophase hematite (np-Hm). The purpose of this abstract is to document the physicospectral properties of hematite in the VNIR (0.35 to 2.2 microns) and MIR (5 to 25 microns) with respect to the terms "nanophase" and "crystalline", "red" and "gray", and "fine-grained" and "coarse-grained". We will show that different "types" of hematite (no-, red-, and gray-Hm) have different spectral responses in the VNIR and MIR regions and that these differences are important for inferring the types of hematite and their relative proportions from remotely sensed spectra of Mars. Because hematite is an alteration product that forms through many different geologic processes, determination of the type of hematite provides important clues about the style and diversity of martian weathering processes.

Lane, Melissa D.↗

Spectral Behavior of Hematite at Visible/Near Infrared and Midinfrared Wavelengths

The oxide mineral hematite alpha-Fe2O3) is present on Mars as evidenced by spectroscopy using visible/near infrared (VNIR) and midinfrared (MIR) wavelengths. The physical nature of this surficial hematite varies from fine-grained, crystalline red hematite (red-Hm) in certain martian bright regions, to coarser-grained, crystalline gray hematite (gray-Hm) in the Sinus Meridiani equatorial site discovered in the Mars Global Surveyor Thermal Emission Spectrometer (MGS-TES) data. The VNIR spectra require that the red hematite is present in amounts subordinate to a second ferric pigment, which accounts for the general shape and position of the martian ferric absorption edge. By analogy with palagonitic tephra and synthetic samples, the pigment is a nanophase ferric oxide, possibly nanophase hematite (np-Hm). The purpose of this abstract is to document the physicospectral properties of hematite in the VNIR (0.35 to 2.2 mm) and MIR (5 to 25 mm) with respect to the terms "nanophase" and "crystalline", "red" and "gray", and "fine-grained" and "coarse-grained". We will show that different "types" of hematite (np-, red-, and gray-Hm) have different spectral responses in the VNIR and MIR regions and that these differences are important for inferring the types of hematite and their relative proportions from remotely sensed spectra of Mars. Because hematite is an alteration product that forms through many different geologic processes, determination of the type of hematite provides important clues about the style and diversity of martian weathering processes. Additional information is contained in the original extended abstract.

Lane, M. D.↗

Dual Microstructure Heat Treatment of a Nickel-Base Disk Alloy

Existing Dual Microstructure Heat Treat (DMHT) technology was successfully applied to Alloy 10, a high strength, nickel-base disk alloy, to produce a disk with a fine grain bore and coarse grain rim. Specimens were extracted from the DMHT disk and tested in tension, creep, fatigue, and crack growth using conditions pertinent to disk applications. These data were then compared with data from "traditional" subsolvus and supersolvus heat treatments for Alloy 10. The results showed the DMHT disk to have a high strength, fatigue resistant bore comparable to that of subsolvus Alloy 10. Further, creep resistance of the DMHT rim was comparable to that of supersolvus Alloy 10. Crack growth resistance in the DMHT rim, while better than that for subsolvus, was inferior to that of supersolvus Alloy 10. The slow cool at the end of the DMHT conversion and/or the subsolvus resolution step are thought to be responsible for degrading rim DMHT crack growth resistance.

Gayda, John↗

High Temperature Spin Testing of a Superalloy Disk With a Dual Grain Structure

Comparative spin tests were run on superalloy disks at an elevated temperature to determine the benefits of a DMHT disk, with a fine grain bore and coarse grain rim, versus a traditional subsolvus disk with a fine grain structure in the bore and rim. The results of these tests showed that the DMHT disk exhibited significantly lower growth at 1500 F. Further, the results of these tests could be accurately predicted using a 2D viscoelastic finite element analysis. These results indicate DMHT technology can be used to extend disk operating temperatures when compared to traditional subsolvus heat treatment options for superalloy disks. However, additional research is required to ensure the safe operation of a DMHT disk under more realistic engine operating conditions. This includes testing to determine the burst margin and cyclic capability of DMHT disks in a spin pit, at a minimum, and ultimately running an engine test with a DMHT disk.

Gayda, John↗

High Temperature Burst Testing of a Superalloy Disk With a Dual Grain Structure

Elevated temperature burst testing of a disk with a dual grain structure made from an advanced nickel-base superalloy, LSHR, was conducted. The disk had a fine grain bore and coarse grain rim, produced using NASA's low cost DMHT technology. The results of the spin testing showed the disk burst at 42 530 rpm in line with predictions based on a 2-D finite element analysis. Further, significant growth of the disk was observed before failure which was also in line with predictions.

Gayda, J.↗

Cyclic Spin Testing of Superalloy Disks With a Dual Grain Microstructure

An aggressive cyclic spin test program was run to verify the reliability of superalloy disks with a dual grain structure, fine grain bore and coarse grain rim, utilizing a disk design with web holes bisecting the grain size transition zone. Results of these tests were compared with conventional disks with uniform grain structures. Analysis of the test results indicated the cyclic performance of disks with a dual grain structure could be estimated to a level of accuracy which does not appear to prohibit the use of this technology in advanced gas turbine engines, although further refinement of lifing methodology is clearly warranted.

Gayda, John↗

Additional Sr Isotopic Heterogeneity in Zagami Olivine-Rich Lithology

Prior isotopic analyses of Zagami have established differing initial Sr-87/Sr-86 (ISr) ratios of among Zagami lithologies, fine-grained (FG), coarse-grained (CG), and dark mottled lithologies (DML)]. The Zagami sample (KPM-NLH000057) newly allocated from the Kanagawa Prefectural Museum of Natural History contained DML and the Ol-rich lithology which included more ferroan olivines (Ol-rich: Fa(sub 97- 99) vs late-stage melt pockets: Fa(sub 90-97)]). We have combined mineralogy-petrology and Rb-Sr isotopic studies on the Kanagawa Zagami sample, which will provide additional clues to the genesis of enriched shergottites and to the evolution of Martian crust and mantle

Misawa, K.↗

Trace Element Abundances in an Unusual Hibonite-Perovskite Refractory Inclusion from Allende

Calcium-aluminum-rich refractory inclusions (CAIs) are thought to be the first-formed solids in the Solar protoplanetary disk and can provide information about the earliest Solar System processes (e.g., [1]). A hibonite-perovskitebearing CAI from the Allende CV3 chondrite (SHAL, [2]) contains a single of 500 micrometers hibonite grain and coarse-grained perovskite. The mineralogy and oxygen isotopic composition of this CAI shows similarities with FUN inclusions, especially HAL [2]. Here we present trace element abundances in SHAL.

Mane, Prajkta↗

Study on grain boundary character and strain distribution of intergranular cracking in the CGHAZ of T23 steel

Intergranular reheat cracking in the coarse-grained heat-affected zone of T23 steel was produced by strain to fracture tests on a Gleeble 3500 thermal–mechanical simulator. Then the grain boundary character, as well as the strain distribution after reheat crack propagation, was studied by electron backscatter diffraction technique. The results showed that incoherent Σ3 boundaries were seldom found on the prior austenite grain boundaries. Therefore, only the type of random high-angle boundaries played a crucial role in the intergranular cracking. Microstructurally cavities and small cracks were preferentially initiated from high-angle grain boundaries. Low-angle grain boundaries and high-angle ones with misorientation angles less than 15° were more resistant to the cracking. More importantly, the fraction of high-angle grain boundaries increased with the plastic strain induced by both temperature gradient and stress in the coarse-grained heat-affected zone, which contributed to the crack initiation and propagation. Furthermore, the strain distributions in the vicinity of cavities and cracks revealed the accommodation processes of plastic deformation during stress relaxation. It also reflected the strength differences between grain interior and grain boundary at different heat-treated temperatures, which had a large influence on the cracking mechanism. - Highlights: • The coincidence site lattice boundaries play little role in the reheat cracking. • Cavity and crack occur at high-angle grain boundaries rather than low-angle ones. • The strain leads low-angle grain boundaries to transform to high-angle ones. • Strain distribution differs for cavity and crack zones at different temperatures.

36 MATERIALS SCIENCE↗

An efficient and reliable predictive method for fluidized bed simulation

In past decades, the continuum approach was the only practical technique to simulate large-scale fluidized bed reactors because discrete approaches suffer from the cost of tracking huge numbers of particles and their collisions. This study significantly improved the computation speed of discrete particle methods in two steps: First, the time-driven hard-sphere (TDHS) algorithm with a larger time-step is proposed allowing a speedup of 20-60 times; second, the number of tracked particles is reduced by adopting the coarse-graining technique gaining an additional 2-3 orders of magnitude speedup of the simulations. A new velocity correction term was introduced and validated in TDHS to solve the over-packing issue in dense granular flow. The TDHS was then coupled with the coarse-graining technique to simulate a pilot-scale riser. The simulation results compared well with experiment data and proved that this new approach can be used for efficient and reliable simulations of large-scale fluidized bed systems.

42 ENGINEERING↗