Results for “CaS” — Page 31

NASA NTRS2023

A Trajectory Algorithm to Support En Route and Terminal Area Self-Spacing Concepts: Fifth Revision

This document describes an algorithm for the generation of a four dimensional trajectory. Input data for this algorithm are similar to an augmented Standard Terminal Arrival (STAR) with the augmentation in the form of altitude or speed crossing restrictions at waypoints on the route. The algorithm calculates the altitude, speed, along path distance, and along path time for each of these waypoints. Wind data at each of these waypoints are also used for the calculation of ground speed and turn radius. This revision of the algorithm now accommodates linear decelerations between two speed-constrained waypoints. While this modification may appear trivial, the calculation of the deceleration rate cannot be accomplished using a closed-form solution. An iterative solution was developed that allowed for the variability of path distance due to speed influence on turn radii, Mach-CAS transition altitude, and the impact of wind on ground speed in calculating an accurate deceleration value.

Aircraft Operations↗

NASA NTRS2023

Ultrasonic Inspection During Autoclave Cure of Reflowable-Interface Composite Joints

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making the interface susceptible to minute quantities of contamination, which can cause weak bonds. Regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded primary-structures due to uncertainty in bond performance. To address this issue, the NASA Convergent Aeronautics Solutions (CAS): Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy-matrix resins to enable reflow and diffusion of the resin at the joint interface during a secondary bonding and cure process that can eliminate the material discontinuity at the interface. Implementing in-situ process monitoring enables assessing the bond quality during processing rather than waiting for post-fabrication mechanical testing to be completed. In this paper, an in-situ ultrasonic inspection system is used to monitor the joining of three composite laminates assembled using the AERoBOND technique. For each panel, the amplitude of the wave reflection at the joint was measured throughout the cure cycle. The results indicate the timing and extent of reflow and cure of the epoxy resin at the joint. Factors indicating end of cure were ascertained and a metric was developed to qualitatively predict acceptable mode-II fracture toughness based on the ultrasonic amplitude at the joint line during cure. In addition, since the inspection system scans an area of the joint, high-resolution localized results can be obtained across the joint.

Tyler B Hudson↗

NASA NTRS2024

Investigating Sulfur-Rich Mercury Analogs Exposed to Simulated Micrometeoroid Bombardment in the Laboratory

Space weathering (SW) continually alters the spectral, microstructural, and chemical characteristics of the surface of airless bodies across the solar system. The effects of SW vary depending on the heliocentric distance and the initial composition of the target surface. While SW on the Moon and S-type asteroids is well documented, our understanding of how this process affects Mercury is at an early stage. Mercury’s interplanetary environment is harsh, with the surface of the planet experiencing an intense solar wind flux as well as a higher flux and velocity of micrometeoroid impactors compared to the Moon and S-type asteroids. In addition, Mercury is also a geochemical endmember, with a surface composition low in Fe (<2 wt.%) and enriched in volatile components, such as sulfur (up to 4 wt.% in the low reflectance material (LRM)). These volatile components are thought to play a major role in the formation of hollows via their sublimation. Sulfur has been hypothesized to occur at the surface of Mercury as sulfide minerals (MgS, CaS) based on its correlation with Mg and Ca in remote sensing data. However, recent observations of chaotic terrains in the north polar area of Mercury and of glacier-like features at lower latitudes indicated that octasulfur (S 8 , elemental sulfur) is another likely constituent of a volatile-rich layer in Mercury’s crust. Its behavior on Mercury may result in a complex cycle of enrichment and depletion. While S is often depleted on small body surfaces, Mercury’s gravity could result in ejected S subsequently returning to the surface and coating regolith grains. Further, the reaction of reduced S-rich gas with glasses of a Mercury-like composition also produced S-rich coatings. However, the precise behavior and evolution of S-rich species exposed to the harsh SW on Mercury remains poorly understood and needs to be further investigated in the laboratory. Here, we present the results of our analyses of the spectral, microstructural, and chemical characteristics of S-rich Mercury analogs irradiated by pulsed laser to simulate the short duration, high temperature events associated with micrometeoroid impacts.

N Bott↗

NASA NTRSDate not supplied

Integration of Automated Systems (IAS) Flight Test - Hazard Perception & Avoidance (HPA) Results

The Integration of Automated Systems (IAS) flight test series concluded in October 2023 in support of NASA's Advanced Air Mobility (AAM) project. These flights include crewed, test (i.e., ownship) and traffic (i.e., intruder) aircraft that flew with unique technologies onboard. The presentation includes overviews of the flight tet itself and the specific results that pertain to the Hazard Perception and Avoidance (HPA) technical areas. HPA tested the FAA's Airborne Collision Avoidance System X (ACAS X), a next-generation collision avoidance tool developed to support different aircraft types and operations. The rotorcraft variant, ACAS Xr, is designed to accommodate existing helicopter platforms and in-development, vertical takeoff and landing (VTOL) concepts, which are critical to the emerging AAM concept of operations. Two configurations of ACAS Xr were examined: Collision Avoidance System (CAS, similar to the Traffic Collision Avoidance System [TCAS] II) and Detect and Avoid (DAA, previously developed to provide added situational awareness for remote pilots). Additionally, this system was flown in cruise and low-speed flight regimes as well as within en-route and (emulated), structured (i.e., dense/urban), and terminal airspaces. Results include the types of alerts generated by ACAS Xr across the different configurations, the distances at which the alerts were generated, response times, manuever sizes, miss distances, and general comments from pilots. Key takeaways and next steps are also provided.

detect and avoid↗

NASA NTRSDate not supplied

Considerations for Sensors Technology Development and Implementation

A brief overview is given on some of the approaches and challenges in sensor technology development and application. Examples of sensors systems that have been developed and demonstrated in applications, as well as a description of the CAS project.

Smart Sensor Additive Manufacturing↗

NASA NTRS2023

Solar Activity Relations in Energetic Electron Events Measured By the MESSENGER Mission

Aims. We perform a statistical study of the relations between the properties of solar energetic electron (SEE) events measured by the MESSENGER mission from 2010 to 2015 and the parameters of the respective parent solar activity phenomena in order to identify the potential correlations between them. During the time of analysis, the MESSENGER heliocentric distance varied between 0.31 and 0.47 au. Methods. We used a published list of 61 SEE events measured by MESSENGER, which includes information on the near-relativistic electron peak intensities, the peak-intensity energy spectral indices, and the measured X-ray peak intensity of the flares related to the SEE events. Taking advantage of multi-viewpoint remote-sensing observations, we reconstructed, whenever possible, the associated coronal mass ejections (CMEs) and shock waves; and we determined the three-dimensional (3D) properties (location, speed, and width) of the CMEs and the maximum speed of the 3D CME-driven shocks in the corona. We used different methods (Spearman, Pearson, and a Bayesian approach, namely the Kelly method to linear regression) to estimate the correlation coefficients between the flare intensity, maximum speed at the apex of the CME-driven shock, CME speed at the apex, and CME width with the electron peak intensities and with the energy spectral indices. In this statistical study, we considered and addressed the limitations of the particle instrument on board MESSENGER (elevated background intensity level, anti-Sun pointing). Results. There is an asymmetry to the east in the range of connection angles (CAs) for which the SEE events present the highest peak intensities, where the CA is the longitudinal separation between the footpoint of the magnetic field connecting to the spacecraft and the flare location. Based on this asymmetry, we define a subsample of well-connected events as when −65° ≤ CA ≤ +33°. For the well-connected sample, we find moderate to strong correlations between the near-relativistic electron peak intensity and the 3D CME-driven shock maximum speed at the apex (Spearman: cc = 0.53 ± 0.05; Pearson: cc = 0.65 ± 0.04; Kelly: cc = 0.87 ± 0.20), the flare peak intensity (Spearman: cc = 0.63 ± 0.03; Pearson: cc = 0.59 ± 0.03; Kelly: cc = 0.74 ± 0.30), and the 3D CME speed at the apex (Spearman: cc = 0.50 ± 0.04; Pearson: cc = 0.46 ± 0.03; Kelly: cc = 0.60 ± 0.39). When including poorly connected events (full sample), the relations between the peak intensities and the solar-activity phenomena are blurred, showing lower correlation coefficients. Conclusions. Based on the comparison of the correlation coefficients presented in this study using near 0.4 au data, (1) both flare and shock-related processes may contribute to the acceleration of near relativistic electrons in large SEE events, in agreement with previous studies based on near 1 au data; and (2) the maximum speed of the CME-driven shock is a better parameter to investigate particle-acceleration-related mechanisms than the average CME speed, as suggested by the stronger correlation with the SEE peak intensities.

Sun↗

NASA NTRSDate not supplied

PAX Mobility

Pax Mobility is a Wicked Wild Discovery activity under the Convergent Aeronautics Solutions (CAS) project. It is intended to cut down the end-to-end travel time and friction for people and goods (referred to as passengers) through: (1) A passenger-oriented paradigm to enable faster mobility that is accessible by all people, end to end (rather than port to port), and that is also safer, more efficient, and sustainable. (2) A total mobility paradigm that integrates modes of mobility to achieve end-to-end passenger objectives. (3) Digital transformation that establishes an agile research and development process to reduce the time to reach end-to-end mobility solutions.

Passenger-oriented total mobility↗

NASA NTRSDate not supplied

Designed Adhesion - Exploring the Unknown

The ability to design materials and substrates for adhesive properties is highly desirable for the aeronautics industry. This includes the ability to design substrates that have low ice adhesion to increase efficiency of the fleet, as well as the ability to design structural adhesives to improve manufacturing rate. The Designed Adhesion group was chosen during the 2023 Wicked Wild Pitch Event sponsored by CAS and is currently in the discovery phase.

Design↗

NASA NTRS2024

Preface to the Special Issue on Modeling and Data Analysis Methods for the SMILE mission

The SMILE (Solar wind Magnetosphere Ionosphere Link Explorer) project (http://www.nssc.cas.cn/smile/, https://www.cosmos.esa.int/web/smile/mission) is a joint spacecraft mission of the European Space Agency (ESA) and the Chinese Academy of Sciences (CAS) with an expected launch in 2025. SMILE aims to study the global interactions of solar wind–magnetosphere–ionosphere innovatively by imaging the Earth’s magnetosheath and cusps in soft X-rays and the northern auroral region in ultraviolet (UV) while simultaneously measuring plasma and magnetic field parameters in the solar wind and magnetosheath along a highly-elliptical and highly-inclined orbit. This special issue is composed of 22 articles, presenting recent progress in modeling and data analysis techniques developed for the SMILE mission. In this preface, we categorize the articles into the following seven topics and provide brief summaries: (1) instrument descriptions of the Soft X-ray Imager (SXI), (2) numerical modeling of the X-ray signals, (3) data processing of the X-ray images, (4) boundary tracing methods from the simulated images, (5) physical phenomena and a mission concept related to the scientific goals of SMILE-SXI, (6) studies of the aurora, and (7) ground-based support for SMILE.

SMILE↗

NASA NTRSDate not supplied

X-57 Systems Engineering Lessons Learned

The X-57 Maxwell is an electric aircraft based on a 4-passenger, twin engine Tecnam P2006T General Aviation aircraft. The X-57 project originally envisioned a straightforward integration of commercial-off-the-shelf hardware components and software into a novel configuration to demonstrate the aerodynamic and performance benefits of Distributed Electric Propulsion (DEP). The project was initially started with a high-risk venture capitalist approach under NASA’s Convergent Aeronautics Solutions (CAS) project, which led to an initial philosophy of Project Management “light” (which was then interpreted as Systems Engineering (SE) “light”). As the project matured, it was forced to transition to one with increasing SE-rigor as the project scope changed, hardware and software deficiencies were found, and the team realized the magnitude of the technical and integration challenges. In hindsight, these technical challenges came in part from an overly optimistic technology readiness assessment (TRA) at the beginning of the project, which resulted in the project assuming that little to no subsystem development would be required. The project’s approach to systems engineering evolved throughout three separate informal phases of the project as it underwent two key transitions as a result of the team wrestling with the technical challenges and resultant changing project scope. This paper discusses the assumptions, approaches, and challenges encountered from a Systems Engineering standpoint in each of the three informal phases of the X-57 project. This paper also provides recommendations on how future projects can apply Systems Engineering best practices upfront along with a realistic TRA to aid projects that find themselves with similar challenges.

Systems Engineering↗

NASA NTRSDate not supplied

Identification and Development of Coordination Procedures Between Upper Class E Traffic Management (ETM) and Surrounding Air Traffic Operations

A recent interest in novel, non-traditional vehicles / missions that plan to operate in Upper Class E (UCE) airspace at or above 60,000 ft has led to efforts by NASA, FAA and the stakeholder communities to research and develop a new concept called Upper Class E Traffic Management (ETM). ETM concept proposes to handle the influx of diverse traffic mix around FL600 and above, utilizing a new traffic management infrastructure, supported by federated service suppliers that are developed by the community stakeholders, for coordinating, monitoring, and executing vehicle operational intent in a designated airspace called ETM Cooperative Area (CA). ETM vehicles are generally expected to reach and operate in ETM CA by first transiting through Class A airspace and potentially through UCE airspace that sits outside of ETM CA. In this paper, a set of use cases have been identified and step-by-step procedures have been developed to handle nominal transitions of ETM vehicles between these operational areas, as well as additional use cases and procedures for authorization and termination of ETM CAs in Class A and/or UCE airspace. The overall research effort in this paper has revealed potential challenges and open questions related to these use cases, especially for the interactions between ETM CA and UCE in both vehicle transition and ETM CA authorization scenarios. The use cases and procedures developed in this paper will inform future ETM integration efforts, as well as research and development into decision support tools needed for the integration.

Upper Class E Traffic Management (ETM)↗

NASA NTRSDate not supplied

Operationalizing “Wickedness” as Analytical and Creative Tools to Transform Aviation

As the world grows increasingly networked and complex, so do challenges faced by aviation and technology professionals (e.g., fighting wildfires and increasing access to healthcare). There is a need to develop new methods to tackle complex socio-technical problems relevant to aviation. The concept of “wicked” problems offers new methods and perspectives for framing complex challenges. In this paper, we present two modes of operationalizing “wickedness” used by NASA’s Convergent Aeronautics Solutions (CAS) Project to develop transformative innovations in aviation: as an analytical, evaluative tool and a creative, generative tool. Through project examples, we demonstrate that using wickedness as a creative tool during the design process enables rich problem exploration with diverse stakeholders and reflection on how a problem is formulated, while usage as an analytical tool can provide criteria for project selection if internal agreement on the definitions of such criteria is established. Operationalizing wickedness as a creative tool may also enable organizational development of a generative mindset to better adapt to our rapidly changing future.

Robyn C Richmond↗

NASA NTRSDate not supplied

Detect and Avoid and Collision Avoidance Flight Test Results with ACAS Xr

In October 2023, the National Aeronautics and Space Administration (NASA) completed its Integration of Automated Systems flight test series, conducted under NASA’s Advanced Air Mobility project and in partnership with Sikorsky and the Defense Advanced Research Projects Agency (DARPA). The flight test effort included two crewed rotorcraft platforms. The first, a modified S-76B helicopter, served as the “ownship” for the duration of the flight test. The second vehicle, a modified S-70, served as the intruder aircraft. One Sikorsky pilot and one NASA test pilot was onboard each aircraft for every test point, with the NASA test pilot responsible for interacting with the research systems under test. Approximately half of the flight test was devoted to assessing the Federal Aviation Administration’s (FAA) next-generation collision avoidance system, the Airborne Collision Avoidance System X for Rotorcraft (ACAS Xr). The two configurations available within ACAS Xr – the Collision Avoidance System (CAS) configuration and the Detect and Avoid (DAA) configuration – were flown with an onboard pilot under Visual Flight Rules in controlled airspace over the Long Island Sound (Connecticut, USA). A total of 33 flight test cards were flown with ACAS Xr active. The ownship was equipped with ACAS Xr and the intruder was equipped with Automatic Dependent Surveillance-Broadcast (ADS-B). The test points were blocked by ACAS Xr configuration, with individual encounters varying the ownship speed (90 knots or 20 knots), the intruder designation (en-route, terminal area, or structured airspace), and method of RA execution (automated or manually executed). Results showed that the ACAS Xr alerting and guidance was largely effective and rated positively by the NASA test pilots, exemplified by zero instances of the pilots overriding an ACAS Xr Resolution Advisory (RA). Key areas of improvement, however, were noted, particularly with regards to the lack of an aural alert indicating a need to accelerate when receiving an RA at low speed and the occurrence of multiple RAs that the pilots found to be unacceptable.

detect and avoid↗

NASA NTRSDate not supplied

FT-01: Autonomous Helicopter Flight Testing Over Long Island Sound Special Session - Hazard Perception and Avoidance Tech Area

This presentation is included as part of a panel reporting on the Integration of Automated Systems (IAS) flight test series. The IAS series concluded in October 2023 and was conducted under NASA’s Advanced Air Mobility project and in partnership with Sikorsky and the Defense Advanced Research Projects Agency (DARPA). The flight test effort included two crewed rotorcraft platforms. The first, a modified S-76B helicopter, served as the “ownship” for the duration of the flight test. The second vehicle, a modified S-70, served as the intruder aircraft. One Sikorsky pilot and one NASA test pilot was onboard each aircraft for every test point, with the NASA test pilot responsible for interacting with the research systems under test. This portion of the panel presentation focuses on the results of the flight test that assessed the Federal Aviation Administration’s (FAA) next-generation collision avoidance system, the Airborne Collision Avoidance System X for Rotorcraft (ACAS Xr). The two configurations available within ACAS Xr – the Collision Avoidance System (CAS) configuration and the Detect and Avoid (DAA) configuration – were flown with an onboard pilot under Visual Flight Rules in controlled airspace over the Long Island Sound (Connecticut, USA). A total of 33 flight test cards were flown with ACAS Xr active. Results showed that the ACAS Xr alerting and guidance was largely effective and rated positively by the NASA test pilots, exemplified by zero instances of the pilots overriding an ACAS Xr Resolution Advisory (RA). Key areas of improvement, however, were noted, particularly with regards to the lack of an aural alert indicating a need to accelerate when receiving an RA at low speed and the occurrence of multiple RAs that the pilots found to be unacceptable.

detect and avoid↗

NASA NTRSDate not supplied

Operationalizing “Wickedness” as Analytical and Creative Tools to Transform Aviation

As the world grows increasingly networked and complex, so do challenges faced by aviation and technology professionals (e.g., fighting wildfires and increasing access to healthcare). There is a need to develop new methods to tackle complex socio-technical problems relevant to aviation. The concept of “wicked” problems offers new methods and perspectives for framing complex challenges. In this paper, we present two modes of operationalizing “wickedness” used by NASA’s Convergent Aeronautics Solutions (CAS) Project to develop transformative innovations in aviation: as an analytical, evaluative tool and a creative, generative tool. Through project examples, we demonstrate that using wickedness as a creative tool during the design process enables rich problem exploration with diverse stakeholders and reflection on how a problem is formulated, while usage as an analytical tool can provide criteria for project selection if internal agreement on the definitions of such criteria is established. Operationalizing wickedness as a creative tool may also enable organizational development of a generative mindset to better adapt to our rapidly changing future.

Robyn Richmond↗

NASA NTRSDate not supplied

Discovery: Strategic Foresight – Helping Aviation Find Problems Worth Solving

Strategic foresight is used in the early stages of the CAS (Convergent Aeronautics Solutions) process. We discover trends, needs, and capabilities from interviews with diverse groups of people, data analytics tools, and from publications. These are analyzed in the context of future scenarios to uncover problem areas that have the highest possible impact on the broadest number of people while ensuring that we are prepared for the future.

Foresight↗

NASA NTRSDate not supplied

Detect and Avoid and Collision Avoidance Flight Test Results with ACAS Xr

In October 2023, the National Aeronautics and Space Administration (NASA) completed its Integration of Automated Systems flight test series, conducted under NASA’s Advanced Air Mobility project and in partnership with Sikorsky and the Defense Advanced Research Projects Agency (DARPA). The flight test effort included two crewed rotorcraft platforms. The first, a modified S-76B helicopter, served as the “ownship” for the duration of the flight test. The second vehicle, a modified S-70, served as the intruder aircraft. One Sikorsky pilot and one NASA test pilot was onboard each aircraft for every test point, with the NASA test pilot responsible for interacting with the research systems under test. Approximately half of the flight test was devoted to assessing the Federal Aviation Administration’s (FAA) next-generation collision avoidance system, the Airborne Collision Avoidance System X for Rotorcraft (ACAS Xr). The two configurations available within ACAS Xr – the Collision Avoidance System (CAS) configuration and the Detect and Avoid (DAA) configuration – were flown with an onboard pilot under Visual Flight Rules in controlled airspace over the Long Island Sound (Connecticut, USA). A total of 33 flight test cards were flown with ACAS Xr active. The ownship was equipped with ACAS Xr and the intruder was equipped with Automatic Dependent Surveillance-Broadcast (ADS-B). The test points were blocked by ACAS Xr configuration, with individual encounters varying the ownship speed (90 knots or 20 knots), the intruder designation (en-route, terminal area, or structured airspace), and method of RA execution (automated or manually executed). Results showed that the ACAS Xr alerting and guidance was largely effective and rated positively by the NASA test pilots, exemplified by zero instances of the pilots overriding an ACAS Xr Resolution Advisory (RA). Key areas of improvement, however, were noted, particularly with regards to the lack of an aural alert indicating a need to accelerate when receiving an RA at low speed and the occurrence of multiple RAs that the pilots found to be unacceptable.

detect and avoid↗

NASA NTRS2024

Uncrewed Aerial Systems for Emergency Medical First Response: A Market Research Report

This report presents the findings from market research conducted for NASA’s Aerial Aid Convergent Aeronautics Solutions (CAS) exploration project, which aims to assess the current state of the market and technological readiness for Uncrewed Aerial Systems (UAS) for medical emergency first response. The research reveals a robust and rapidly growing market for UAS, with a notable emerging sector for Drones as First Responders (DFR). Despite this growth, DFR applications are currently limited by regulatory, technical, and other challenges, which restrict their use primarily to manned remote video surveillance, and therefore are primarily employed by police units. To our knowledge, there is no evidence of UAS being utilized by medical first responders for scene assessment. Limited evidence exists for closely related applications; however, these are mostly confined to pilot programs for the delivery of medical supplies or equipment. Although there has been discussion around fully autonomous DFR applications for medical purposes such as UAS ambulances or patient transport drones, these applications are generally not yet operational in practice. The technology for full autonomy, especially in guidance and control, has seen significant advancements, and recent Federal Aviation Administration (FAA)regulations are likely to accelerate adoption. Computer vision algorithms for fully autonomous medical emergency response scene surveillance are primed for advancement and deployment. A notable gap likely exists between advancements in computer vision research and what is being integrated in the commercial DFR sector. This gap is primarily due to challenges such as quality assurance for autonomous systems, the availability of application-specific training datasets for computer vision algorithms, regulatory constraints, and public perception and privacy concerns.

Joshua M Fody↗