Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CALORIMETRY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Preparation of Low-Density Microcellular Foams from Recycled PET Modified by Solid State Polymerization and Chain Extension

Recycled polyethylene-terephthalate (RPET) bottle regrinds were physically foamed after two types of industrially feasible molecular weight increasing processes. Intrinsic viscosity (IV) of initial waste (0.71 dL/g) increased both after reactive extrusion carried out using a multifunctional epoxy-based chain extender (0.74 dL/g) and after solid state polycondensation (SSP) (0.78 dL/g), while capillary rheometry revealed higher degree of branching in the chain extended PET material. Despite the relatively low IV values (below 0.80 dL/g), physical foaming, a mild and cost-efficient way, was successful in both cases, uniform microcellular foam structures with void fractions ranging between 75 and 83% were achieved. During the experiments morphology change in the materials was tracked by differential scanning calorimetry (DSC) besides recording IV values. The IV drop during foaming was between 0.03 and 0.10 depending on the pre-processing technology. Structure of foams produced from the two different modified RPET materials was compared with each other based on scanning electron microscopic imaging of cryogenic fracture surfaces. The average cell diameters were measured to be 213 and 360 µm in the case of chain extended and SSP-modified materials, respectively.

36 MATERIALS SCIENCE↗

Biodegradation of Yerba Mate Waste Based Fertilizer Capsules. Effect of Temperature

Yerba mate waste based urea fertilizer capsules were obtained and characterized. Yerba mate powder (YMP) content in these encapsulation systems ranged from 52 to 82% for the different formulations. The aim of the study was to evaluate the effect of yerba mate powder:calcium alginate ratio and the assay temperature on capsule degradation and urea release rate in soil. Degradation evolution was monitored by microbiological tests, environmental scanning electronic microscopy, differential scanning calorimetry and Fourier transform infrared spectrometry. Encapsulation efficiency increased with YMP content. The green fertilizing systems generated did not inhibit microorganism development in soil. Degradation was slower for capsules with higher YMP content. Capsules with high YMP content released lower amounts of urea. Both degradation and release rates increased with assay temperature. The recycling of yerba mate powder as a green composite material originated a new fertilizer system.

36 MATERIALS SCIENCE↗

Cardanol Functionalized Carboxylated Acrylonitrile Butadiene Rubber for Better Processability, Technical Properties and Biocompatibility

The present investigation deals with the latex stage functionalization of carboxylated acrylonitrile butadiene rubber (XNBR) by chemically grafting cardanol onto its backbone main chain to impart multifunctional characteristics to it. The grafting of cardanol onto XNBR in the latex stage has been accomplished successfully using benzoyl peroxide (BPO) as a free radical initiator. Cardanol grafted XNBR (C-g-XNBR) exhibited an increase in molecular weight (7.5%) with an increase in PDI (polydispersity index). The optimum grafting parameters were found to be of 1 phr BPO with 15 phr cardanol at a reaction temperature of 80 °C and a reaction time of 10 h using “Taguchi methodology”. The maximum percentage grafting (PG) and grafting efficiency (GE) were estimated to be 13.8 and 92.8%, respectively at the optimum combination of the reaction parameters. Differential scanning calorimetry and dynamic mechanical analysis results exhibited a decrease in T{sub g} value for the functionalized elastomer. Thermogravimetric analysis displayed an increase in the thermal stability of C-g-XNBR. MTT [3-(4,5-dimethylthiazol-2yl)-2,5-diphenyltetrazolium bromide] assay and hemolysis studies proved that functionalized rubber as biocompatible. Moreover, functionalized XNBR exhibited a potential bactericidal effect against Staphylococcus aureus and Escherichia coli strains. Fire and flame retardancy study revealed an increased LOI (limiting oxygen index) for C-g-XNBR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rheology, Mechanical Properties and Morphology of Poly(lactic acid)/Ethylene Vinyl Acetate Blends

In this work, the effect of ethylene vinyl acetate (EVA) content on the rheology, mechanical properties, and morphology of poly (lactic acid) (PLA)/EVA blends was investigated. Differential Scanning Calorimetry (DSC) showed that the addition of EVA to PLA decreased the degree of crystallinity of PLA. Dynamic Mechanical Thermal Analysis (DMTA) results showed that the presence of EVA copolymer increased the cold crystallization temperature (T{sub cc}) of PLA. The addition of 10% of EVA to PLA substantially increased the impact strength. Morphology analysis by Scanning Electron Microscopy (SEM) indicated the immiscibility between PLA and EVA phases and an in increase the EVA average dispersed phase domains size with the increase in EVA content. Rheological measurements under oscillatory shear flow showed that storage modulus (G′) increased with the increase in the EVA content at low frequencies and is related to the increase in the EVA dispersed phase domains size, as also observed by relaxation spectrum analysis. Cole–Cole plots of imaginary viscosity (η″) versus real viscosity (η′) and Han plots of storage modulus (G′) versus loss modulus (G″) indicated that PLA and EVA phases are immiscible, as also observed by SEM.

36 MATERIALS SCIENCE↗

Development of Green Composites Based on Polypropylene and Corncob Agricultural Residue

Green composites of polypropylene (PP) and corncob (CCB) agricultural residue with CCB content ranging from 5 to 30 wt% were compounded by melt extrusion and their properties investigated by density measurements, thermogravimetric analyses, differential scanning calorimetry, scanning electron microscopy (SEM) and tension, flexural and impact properties. Properties were dependent on CCB content. SEM micrographs showed that PP/CCB composites are composed of all layers of the corncob, but with a higher content of woody ring and pith. Composites with CCB up to 20 wt% presented particles evenly dispersed into PP matrix and density values ranging from 0.929 to 1.026 g/cm{sup 3}. Thermal analyses showed that CCB is thermally stable up to 200 °C, ensuring that no degradation took place during processing, and PP/CCB composites are more crystalline than neat PP. Tensile strength and elongation at break of the composites decreased respectively from 30 to 20 MPa, and 22.7 to 3.7%, and the elastic modulus increased while the impact strength remained practically constant at 14 J/m for the filling contents tested. Elastic and flexural moduli increased respectively from 906 MPa to 1.1 GPa and from to 1.26 to 1.81 GPa with corncob addition.

36 MATERIALS SCIENCE↗

Preparation, Characterization, and Antioxidant Activity of β-Carotene Impregnated Polyurethane Based on Epoxidized Soybean Oil and Malic Acid

A new polyol was synthesized based on epoxidized soybean oil (ESO) and malic acid (MA) for the formulation of a bio-based polyurethane. The synthesized polyol was characterized by Fourier transform-infrared spectroscopy, nuclear magnetic resonance spectroscopy, and mass spectrometry. Polyurethanes were formed by reacting the synthesized ESO-MA polyol with 1,6-hexamethylene diisocyanate at different isocyanate/hydroxyl ratios. The tensile and thermal properties of the prepared polyurethanes were analyzed by differential scanning calorimetry, thermogravimetric analysis, and universal testing machine. The polyurethanes exhibited a tensile strength of 1.34–5.56 MPa, an elongation at break of 20–41%, and a glass transition temperature of − 2.7 to 0.6 °C. In addition, β-carotene, a natural antioxidant, was impregnated on the polyurethane surface and its effect on the tensile and thermal properties of polyurethane was investigated. An increase in tensile strength and a reduction in elongation at break were observed in these β-carotene impregnated polyurethane films. They also showed up to 61% radical scavenging activity against 2,2-diphenyl-1-picryhydrazyl radical in methanol. Moreover, these films retained radical scavenging activity for more than 50 days.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conductivity of PEO/PLA Doped Liquid Crystal Ionomer Solid Polymer Electrolyte in Mesomorphic Range

A novel polyethylene oxide (PEO)/polylactic acid (PLA) solid polymer electrolyte (SPE) doped with Liquid crystal ionomer (LCI) was prepared by automatic scraping membrane technology and the liquid crystal property of LCI was proposed as an effective strategy to improve the conductivity. The highest conductivity of the SPE with 0.5 wt% LCI achieve a value of 2.19 × 10{sup −4} S/cm at 17 °C which is approximately four orders of magnitude higher than that of the original PEO solid polymer electrolyte, conductivity at room temperature is 10{sup −7}–10{sup −8} S/cm. This is because the crystallinity is reduced by 25.3% compared to the pure PEO host. Differential Scanning Calorimetry (DSC) and polarizing microscope (POM) characterize the structure and properties of LCI. Electrochemical Impedance Spectroscopy (EIS) shows that the conductivity of the polymer electrolyte with 0.5 wt% LCI increased abruptly at 35 °C as the temperature is higher than T{sub g} of LCI, reaching 6.37 × 10{sup −4} S/cm which is 191% higher than that at 17 °C. There ionic conductivity has been improved extremely by continuous channel for efficient ion transportation, especially at the microtherm. And this change is greater at the elevated temperature regions, in line with the VTF equation. In summary, LCI’s liquid crystal performance can be used as an effective strategy to improve the low temperature conductivity of SPE.

36 MATERIALS SCIENCE↗

Thermal, Rheological and Mechanical Properties of PETG/rPETG Blends

This paper presents the reuse process of post-consumer printed foils made of glycol-modified poly(ethylene terephthalate) (PETG). Fourier-transform infrared spectroscopy and a scanning electron microscope confirmed that these foils consist of PETG and PS layers. Firstly, foil pieces were immersed in the organic solution to remove all prints and after washing and drying they were extruded into regranulate rPETG pellets. Three types of PETG/rPETG blends were fabricated with the addition of 10, 20 and 30 wt% of virgin PETG. Microscopic analysis of the blends confirmed their homogeneity, as was also shown by the fact that there was only one glass transition peak in the heating curve given by differential scanning calorimetry. Moreover, in the presence of fresh PETG the degradation temperatures of rPETG improved significantly, and the viscosity of all blends was reduced as a result of shortened macromolecule chains in rPETG. Mechanical analysis of the materials showed that all blends have comparable tensile strength and a Young’s modulus that is higher than rPETG but lower than virgin PETG. Elongation at break decreases together with the content of rPETG.

36 MATERIALS SCIENCE↗

Soybean Oil Modified Bio-based Poly(vinyl alcohol)s via Ring-Opening Polymerization

In this paper, a simple method to modify the poly(vinyl alcohol) (PVA) through ring-opening reaction of epoxidized soybean oil (ESBO), catalyzed by hydrochloric acid is reported. The effect of ESBO loading ratio, in terms of mole (PVA/ESBO (n/n) = 1:0.5; 1:1 and 1:1.5) in the reaction medium, on the biodegradable, wettability and thermal properties of final PVA-SBO films is systematically investigated, comparing with PVA. The formation of PVA-SBOs is structurally confirmed by Fourier transform infrared (FT-IR) spectroscopy, whereas their wettability and thermal properties are studied by water contact angle (WCA) measurement, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC), respectively. The obtained PVA-SBOs with higher ESBO loading exhibit both improved thermal properties and higher hydrophobic characteristic compared to others. Furthermore, biodegradability of resulting PVA-SBOs is also investigated by enzymatic degradation experiments. It is determined that around 34% of PVA is degraded by enzymatic experiments after 30 days and PVA-SBO with lower ESBO loading is more degraded than others with around 52%. Consequently, some experimental results are presented to indicate that PVA-SBOs are encouraging materials for diverse applications and their extensions can be good candidate for reducing the environmental problem and consumption of petroleum resources.

36 MATERIALS SCIENCE↗

Effect of Chromium Substitution on Structural and Magnetic Properties of Nickel-Cobalt Ferrite Nanoparticles Synthesized by Co-precipitation Method

Ni{sub 0.3}Co{sub 0.7}Cr{sub x}Fe{sub 2−x}O{sub 4} (x = 0, 0.2, 0.4, and 0.6) nanoparticles were synthesized by co-precipitation method followed by annealing treatment. The structural and magnetic properties of the samples were determined by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, thermogravimetric and differential scanning calorimetry (TG-DSC) analysis, and a vibrating sample magnetometer (VSM) at room temperature. The XRD patterns revealed a single-phase cubic spinel structure for all the annealed products. The average crystallite size is in the range of 45–60 nm. Cation distribution by XRD analysis indicated that Cr{sup 3+} ions preferentially replace Fe{sup 3+} ions from the octahedral sites due to their favorable crystal field effects; with increasing Cr content, it was observed that Co{sup 2+} migrated from octahedral sites to tetrahedral sites. The decrease in saturation magnetization with the increase in Cr concentration could be attributed to reduction in the super-exchange interaction between the A and B sublattices. The observed decrease in coercivity can be explained by reduction in magneto-crystalline anisotropy that resulted from migration of Co{sup 2+} ions from B sites to A sites with the increase in Cr content.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improvement of the Magnetization and Coercivity of La{sub 0.67}Ca{sub 0.33}MnO{sub 3} Induced by Substitution of Nickel for Manganese

La{sub 0.67}Ca{sub 0.33}Mn{sub 1−x}Ni{sub x}O{sub 3} (0 ≤x ≤ 0.3) is synthesized by solid-state reaction at low temperatures, followed by calcination in air. The precursor and its calcined products are characterized by thermogravimetry and differential scanning calorimetry, x-ray powder diffraction, scanning electron microscopy, and vibrating sample magnetometer. A high-crystallized La{sub 0.67}Ca{sub 0.33}Mn{sub 1−x}Ni{sub x}O{sub 3} with an orthorhombic structure is obtained when the precursor is calcined at 900{sup ∘}C in air for 3 h. Crystallite size of La{sub 0.67}Ca{sub 0.33}Mn{sub 1−x}Ni{sub x}O{sub 3} increases with the increase of Ni content, attributed to the decrease of lattice strains of the La{sub 0.67}Ca{sub 0.33}Mn{sub 1−x}Ni{sub x}O{sub 3} with the increase in Ni content. Nickel substitution can markedly improve coercivity and specific magnetization of La{sub 0.67}Ca{sub 0.33}Mn{sub 1−x}Ni{sub x}O{sub 3}. The coercive field (9 Oe) of La{sub 0.67}Ca{sub 0.33}Mn{sub 0.7}Ni{sub 0.3}O{sub 3} is higher, even at 293 K, indicating that La{sub 0.67}Ca{sub 0.33}Mn{sub 0.7}Ni{sub 0.3}O{sub 3} continues being ferromagnetic above 260 K (Curie temperature for LCMO).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of Microwave-Assisted Annealing on the Structure and Magnetic Properties of (Nd{sub 0.75}Pr{sub 0.25}){sub 9}Fe{sub 72}Ti{sub 1}Zr{sub 3}Mn{sub x} Mo{sub 4−x}B{sub 10.5}C{sub 0.5} Amorphous Ribbons

The amorphous as-spun ribbons with nominal composition (Nd{sub 0.75}Pr{sub 0.25}){sub 9}Fe{sub 72}Ti{sub 1}Zr{sub 3}Mn{sub x}Mo{sub 4−x}B{sub 10.5}C{sub 0.5}(x = 1, 2, 3) were annealed by microwave-assisted annealing. The effects of the Mn-doped alloys on glass-forming ability (GFA), crystallization, and magnetic properties of the Nd{sub 2}Fe{sub 14}B/α-Fe nanocomposite magnets were examined by thermal differential scanning calorimetry (DSC), X-ray diffraction (XRD), and vibrating sample magnetometry (VSM). An appropriate amount of Mn was beneficial to the optimization of the structure and magnetic properties. Compared with conventional annealing, the microwave-assisted annealing has contributed to the precipitation of hard magnetic phases and adjusted the proportion of hard and soft magnetic phases. The optimum magnetic properties with coercivity up to 805 kA/m were found for ribbons (with composition x = 1) annealed under the microwave power of 2000 W for 10 min.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Structural and Magnetic Characteristics of Nanocrystalline Co{sub 82}Zr{sub 18} Alloy

In the present study, the structural and magnetic characteristics of nanocrystalline Co{sub 82}Zr{sub 18} alloy with different structure and crystallite sizes were investigated. In this regard, the nanocrystalline Co{sub 82}Zr{sub 18} sample with different structure and crystallite sizes were prepared using a copper boat vacuum induction melting plus melt spinning and subsequent annealing processes. The prepared samples were characterized using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), differential scanning calorimetry (DSC), and vibrating scanning magnetometer (VSM). According to achieved results, single-phase structure of Zr{sub 2}Co{sub 11} can successfully form by means of melt spinning process at wheel speed of 40 m/s. The melt-spun ribbons exhibit hard magnetic properties with the coercivity and saturation of magnetization in the range of 2.3 kOe and 58 emu/g, respectively. The highest value of coercivity in Co{sub 82}Zr{sub 18} alloy was estimated to be about 3 kOe in annealed sample at 500{sup ∘}C for 1 h.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Non-isothermal Crystallization Kinetics and Magnetic Properties of FeCoNiCrZr Metallic Glass

In the present paper, the non-isothermal crystallization kinetics, crystallization process, and magnetic properties of (Fe{sub 0.52}Co{sub 0.30}Ni{sub 0.18}){sub 73}Cr{sub 17}Zr{sub 10} metallic glass were studied by means of differential scanning calorimetry (DSC), Kissinger equation, Ozawa equation, Kempen model, and vibrating sample magnetometer (VSM), respectively. According to the classical nucleation theory, the value of Avrami exponent (n), initially being larger than 4 which implies that phase transformation mechanism is typical for interface-controlled three-dimensional (3-D) growth with increasing nucleation rates, along with the development of crystallization, decreases to 1.5 ∼ 2, which implies that the growth mechanism changes to diffusion-controlled 3-D growth with decreasing nucleation rates; finally, the nucleation rates decrease to zero. Through proper annealing conditions, the saturation magnetization(M{sub s}) values of the annealed sample can reach up to 106.8A m{sup 2} kg{sup − 1}, the crystallization process of this alloy is amorphous → α-Fe(Co) + amorphous′ → α-Fe(Co) + Cr{sub 2}Ni{sub 3} + Fe{sub 3}Ni{sub 2} + Cr{sub 2}Zr + unidentified phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects on Glass Forming Ability, Microstructure, Crystallization Behaviors, and Magnetic Properties of Si Substituting for P in Fe-Rich Fe{sub 86}B{sub 13−x}Si{sub x}P{sub 1}Cu{sub 0.6}Hf{sub 0.4} Alloys

In the paper, we have studied the effects on glass forming ability (GFA), microstructure, crystallization behaviors, and saturation magnetization (M{sub s}) of Si substitution for P in Fe-rich Fe{sub 86}B{sub 12}Si{sub x}P{sub 1−x}Cu{sub 0.4}Hf{sub 0.6} alloys. The amorphous structure is identified by X-ray diffraction first, and the patterns with Si addition less than x = 0.75 only show one halo scattering peak at 2θ = 45°; further, the ribbons with entirely amorphous structure have been fabricated successfully and the alloys have a good GFA. Then, by differential scanning calorimetry testing, the curves show two separated exothermic peaks and the ribbons will go through a two-step crystallization before reaching stable state; further, the first peak is ensured by the crystallization of a-Fe phase while the second peak is ensured by the precipitation of FeB or Fe(BP) compounds. As Si was added, the apparent activation energy of the first crystallization (E{sub a1}) and the second crystallization (E{sub a2}) shows an increased tendency first and then decreases slightly. By comparison, as x = 0, x = 0.25, and x = 0.5, the ribbons easily form Hf{sub 3}P{sub 2} compounds during the first crystallization process simultaneously, where the ribbons of x = 0.75 and x = 1.0 are easier to finish the first crystallization for forming the uniform a-Fe phase entirely. By vibrating sample magnetometer testing, with the addition of Si, M{sub s} value shows an increased trend and reaches to the maximum about 177.5 emu/g (x = 1.0), and which shows an increased trend in the subsequent annealing process and reaches to the maximum 206.3 emu/g (x = 0), 212.3 emu/g (x = 0.25), 214.2 emu/g (x = 0.5), 214.9 emu/g (x = 0.75), and 208.3 emu/g (x = 1.0) as the annealing temperature higher than T{sub p1} but less than T{sub x2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic and Kinetical Properties of Fe-27%Ni-4%Mn and Fe-27%Ni-4%Mn-2%Zn Alloys Investigated by VSM and DSC

We report on the structural, thermal, and magnetic properties of thermally induced martensite in Fe-27%Ni-4%Mn and Fe-27%Ni-4%Mn-2%Zn alloys. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and vibrating sample magnetometry (VSM) techniques were employed in the present research. SEM observations revealed the lath martensite morphology formation in both Fe-27%Ni-4%Mn and Fe-27%Ni-4%Mn-2%Zn alloys. As well, the thermally induced martensite start temperature (M{sub s}) was determined to be − 27.18 °C for Fe-27%Ni-4%Mn and − 40.63 °C for Fe-27%Ni-4%Mn-2%Zn alloy from DSC measurements. Further, the Curie temperature was detected at 160 K for Fe-27%Ni-4%Mn and 196 K for Fe-27%Ni-4%Mn-2%Zn alloys after VSM measurements where magnetic saturation values were measured at 20 emu g{sup − 1} for Fe-27%Ni-4%Mn alloy and 18 emu g{sup − 1} for Fe-27%Ni-4%Mn-2%Zn alloy, respectively. The coercivity value of the alloys was also found to be 0.082 kOe for Fe-27%Ni-4%Mn and 0.050 kOe for Fe-27%Ni-4%Mn-2%Zn alloys. Finally, the effect of Zn addition to the austenite–martensite phase tarnsformations of Fe-27%Ni-4%Mn was discussed in detail according to structural, thermal, and magnetic properties of both alloys after a quantitative experimental comparison.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

RADIATION EFFECTS IN PHYSICAL AGING OF BINARY As-S AND As-Se GLASSES

Radiation-induced physical aging effects are studied in binary AsxS100-x and AsxSe100-x (30 ≤ x ≤ 42) glasses by conventional differential scanning calorimetry (DSC) method. It is shown that γ-irradiation (Co60 source, ~ 3 MGy dose) of glassy AsxS100-x caused a measurable increase in glass transition temperature and endothermic peak area in the vicinity of glass transition region, which was associated with acceleration of structural relaxation processes in these materials. In contrast to sulfide glasses, the samples of As-Se family did not exhibit any significant changes in DSC curves after γ-irradiation. The observed difference in radiation-induced physical aging between sulfides and selenides was explained by more effective destruction-polymerization transformations and possible metastable defects formation in S-based glassy network.

36 MATERIALS SCIENCE↗

The Effect of Crystallizing and Non-crystallizing Cosolutes on Succinate Buffer Crystallization and the Consequent pH Shift in Frozen Solutions

To effectively inhibit succinate buffer crystallization and the consequent pH changes in frozen solutions. Using differential scanning calorimetry (DSC) and X-ray diffractometry (XRD), the crystallization behavior of succinate buffer in the presence of either (i) a crystallizing (glycine, mannitol, trehalose) or (ii) a non-crystallizing cosolute (sucrose) was evaluated. Aqueous succinate buffer solutions, 50 or 200 mM, at pH values 4.0 or 6.0 were cooled from room temperature to -25 C at 0.5 C/min. The pH of the solution was measured as a function of temperature using a probe designed to function at low temperatures. The final lyophiles prepared from these solutions were characterized using synchrotron radiation. When the succinic acid solution buffered to pH 4.0, in the absence of a cosolute, was cooled, there was a pronounced shift in the freeze-concentrate pH. Glycine and mannitol, which have a tendency to crystallize in frozen solutions, remained amorphous when the initial pH was 6.0. Under this condition, they also inhibited buffer crystallization and prevented pH change. At pH 4.0 (50 mM initial concentration), glycine and mannitol crystallized and did not prevent pH change in frozen solutions. While sucrose, a non-crystallizing cosolute, did not completely prevent buffer crystallization, the extent of crystallization was reduced. Sucrose decomposition, based on XRD peaks attributable to {beta}-D-glucose, was observed in frozen buffer solutions with an initial pH of 4.0. Trehalose completely inhibited crystallization of the buffer components when the initial pH was 6.0 but not at pH 4.0. At the lower pH, the crystallization of both trehalose dihydrate and buffer components was evident. When retained amorphous, sucrose and trehalose effectively inhibited succinate buffer component crystallization and the consequent pH shift. However, when trehalose crystallized or sucrose degraded to yield a crystalline decomposition product, crystallization of buffer was observed. Similarly, glycine and mannitol, two widely used bulking agents, inhibited buffer component crystallization only when retained amorphous. In addition to stabilizing the active pharmaceutical ingredient, lyoprotectants may prevent solution pH shift by inhibiting buffer crystallization.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗