Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ANTIMONY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Electrical and structural properties of binary Ga–Sb phase change memory alloys

Material properties of Ga–Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for analog phase change memory (PCM) applications. Crystallization of this alloy was shown to occur in the temperature range of 180–264 °C, with activation energy >2.5 eV depending on the composition. X-ray diffraction (XRD) studies showed phase separation upon crystallization into two phases, Ga-doped A7 antimony and cubic zinc-blende GaSb. Synchrotron in situ XRD analysis revealed that crystallization into the A7 phase is accompanied by Ga out-diffusion from the grains. X-ray absorption fine structure studies of the local structure of these alloys demonstrated a bond length decrease with a stable coordination number of 4 upon amorphous-to-crystalline phase transformation. Mushroom cell structures built with Ga–Sb alloys on ø110 nm TiN heater show a phase change material resistance switching behavior with resistance ratio >100 under electrical pulse measurements. TEM and Energy Dispersive Spectroscopy (EDS) studies of the Ga–Sb cells after ∼100 switching cycles revealed that partial SET or intermediate resistance states are attained by the variation of the grain size of the material as well as the Ga content in the A7 phase. A mechanism for a reversible composition control is proposed for analog cell performance. These results indicate that Te-free Ga–Sb binary alloys are potential candidates for analog PCM applications.

Ume, Rubab (ORCID:0000000324766900)↗

Conductivity space isotherm behavior in quantum anomalous Hall devices

The quantum Hall effect (QHE) has enhanced accessibility to measure and disseminate electrical units, owed in part to the recently redefined International System of Units in 2019. Graphene remains one of the preferred options to realize the ohm despite the limitations of high magnetic fields to produce a robust QHE. Topological insulators, on the other hand, show promise in providing quantized resistance via the quantum anomalous Hall effect, a phenomenon that removes the need for magnetic fields during operation. To optimize future devices for metrological applications, it is important to gain a better understanding of magnetically doped topological insulators like Cr-doped bismuth antimony telluride. The application of differential conductivity space analyses offers a more sensitive way to analyze the data and distinguish between 2D and 3D transport behaviors. This is particularly important in thin films, where the transition between 2D and 3D behavior can be subtle. The ability to confidently determine the dimensionality of the transport is crucial for selecting appropriate theoretical models for future device optimization. Furthermore, this work identifies variable range hopping as the dominant transport mechanism in the 2D regime using a rigorous statistical analysis (via the Bayes factor). These elements assist in the understanding of microscopic processes that govern charge transport in these materials.

Tran, N. T. M. [National Inst. of Standards and Te↗

Higher thermoelectric performance of Zintl phases (Eu 0.5 Yb 0.5 ) 1−x Ca x Mg 2 Bi 2 by band engineering and strain fluctuation

Significance The search for high-efficiency thermoelectric materials encompasses many classes of semiconductors. Zintl phases are attractive thermoelectric materials for thermoelectric applications. Here, we report the high thermoelectric performance of the rarely studied bismuth (Bi)-based Zintl phases (Eu 0.5 Yb 0.5 ) 1−x Ca x Mg 2 Bi 2 with the record figure-of-merit ZT as high as 1.3 at 873 K. This ZT value is, to our knowledge, the highest ever reported in CaAl 2 Si 2 -based structures, especially compared with the best antimony (Sb)-based YbZn 0.4 Cd 1.6 Sb 2 compound. Because Sb-based Zintl compounds have been studied for many decades, this Bi-based Zintl phase with high thermoelectric properties could be a good thermoelectric material candidate in the future.

Shuai, Jing↗

Spectral dynamics of shift current in ferroelectric semiconductor SbSI

Photoexcitation in solids brings about transitions of electrons/holes between different electronic bands. If the solid lacks an inversion symmetry, these electronic transitions support spontaneous photocurrent due to the geometric phase of the constituting electronic bands: the Berry connection. This photocurrent, termed shift current, is expected to emerge on the timescale of primary photoexcitation process. We observe ultrafast evolution of the shift current in a prototypical ferroelectric semiconductor antimony sulfur iodide (SbSI) by detecting emitted terahertz electromagnetic waves. By sweeping the excitation photon energy across the bandgap, ultrafast electron dynamics as a source of terahertz emission abruptly changes its nature, reflecting a contribution of Berry connection on interband optical transition. The shift excitation carries a net charge flow and is followed by a swing over of the electron cloud on a subpicosecond timescale. Understanding these substantive characters of the shift current with the help of first-principles calculation will pave the way for its application to ultrafast sensors and solar cells.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Crystal, magnetic, calorimetric and electronic structure investigation of GdScGe 1– x Sb x compounds

Here, experimental investigations of crystal structure, magnetism and heat capacity of compounds in the pseudoternary GdScGe-GdScSb system combined with density functional theory projections have been employed to clarify the interplay between the crystal structure and magnetism in this series of RTX materials (R = rare-earth, $ T$ = transition metal and X = p-block element). We demonstrate that the CeScSi-type structure adopted by GdScGe and CeFeSi-type structure adopted by GdScSb coexist over a limited range of compositions $0.65 \leqslant x \leqslant 0.9$ . Antimony for Ge substitutions in GdScGe result in an anisotropic expansion of the unit cell of the parent that is most pronounced along the c axis. We believe that such expansion acts as the driving force for the instability of the double layer CeScSi-type structure of the parent germanide. Extensive, yet limited Sb substitutions $0 \leqslant x < 0.65$ lead to a strong reduction of the Curie temperature compared to the GdScGe parent, but without affecting the saturation magnetization. With a further increase in Sb content, the first compositions showing the presence of the CeFeSi-type structure of the antimonide, $x \approx 0.7$ , coincide with the appearance of an antiferromagnetic phase. The application of a finite magnetic field reveals a jump in magnetization toward a fully saturated ferromagnetic state. This antiferro–ferromagnetic transformation is not associated with a sizeable latent heat, as confirmed by heat capacity measurements. The electronic structure calculations for $x = 0.75$ indicate that the key factor in the conversion from the ferromagnetic CeScSi-type to the antiferromagnetic CeFeSi-type structure is the disappearance of the induced magnetic moments on Sc. For the parent antimonide, heat capacity measurements indicate an additional transition below the main antiferromagnetic transition.

36 MATERIALS SCIENCE↗

Emerging inorganic solar cell efficiency tables (version 2)

Abstract This paper presents the second version of the efficiency tables of materials considered as emerging inorganic absorbers for photovoltaic solar cell technologies. The materials collected in these tables are selected based on their progress in recent years, and their demonstrated potential as future photovoltaic absorbers. The first part of the paper consists of the guidelines for the inclusion of the different technologies in this paper, the verification means used by the authors, and recommendation for measurement best practices. The second part details the highest world-class certified solar cell efficiencies, and the highest non-certified cases (some independently confirmed). The third part highlights the new entries including the record efficiencies, as well as new materials included in this version of the tables. The final part is dedicated to review a specific aspect of materials research that the authors consider of high relevance for the scientific community. In this version of the efficiency tables, we are including an overview of the latest progress in quasi one-dimensional absorbers, such as antimony chalcogenides, for photovoltaic applications.

14 SOLAR ENERGY↗

P-type conductivity in Sn-doped Sb 2 Se 3

Abstract Antimony selenide (Sb 2 Se 3 ) is a promising absorber material for thin-film photovoltaics. However, certain areas of fundamental understanding of this material remain incomplete and this presents a barrier to further efficiency gains. In particular, recent studies have highlighted the role of majority carrier type and extrinsic doping in drastically changing the performance of high efficiency devices (Hobson et al 2020 Chem. Mater. 32 2621–30). Herein, Sn-doped Sb 2 Se 3 bulk crystals are shown to exhibit p-type conductivity using Hall effect and hot-probe measurements. The measured conductivities are higher than those achieved through native defects alone, but with a carrier density (up to 7.4 × 10 14 cm −3 ) several orders of magnitude smaller than the quantity of Sn included in the source material. Additionally, a combination of ultraviolet, x-ray and hard x-ray photoemission spectroscopies are employed to obtain a non-destructive depth profile of the valence band maximum, confirming p-type conductivity and indicating a majority carrier type inversion layer at the surface. Finally, these results are supported by density functional theory calculations of the defect formation energies in Sn-doped Sb 2 Se 3 , showing a possible limit on the carrier concentration achievable with Sn as a dopant. This study sheds light on the effectiveness of Sn as a p-type dopant in Sb 2 Se 3 and highlights avenues for further optimisation of doped Sb 2 Se 3 for solar energy devices.

36 MATERIALS SCIENCE↗

Exploration for astromers near 132 Sn with the Canadian Penning Trap

Nuclear isomers can have significant impacts on astrophysical nucleosynthesis processes, with recent efforts demonstrating that the population of isomeric states with different half-lives may require separate treatment in reaction networks to accurately capture the differences in heating or in identifiable electromagnetic signals. Several potential so-called “astromers” in tin and antimony isotopes near doubly magic 132 Sn were identified and direct mass measurements of their ground and isomeric states were performed with the Canadian Penning Trap at Argonne National Laboratory's CARIBU facility, and their impact on astrophysical reaction rates and in reaction networks was calculated. Finally, it was found that 129⁢𝑔,𝑚 Sn , with measured mass excesses of −80593.2⁢(25) and −80557.4⁢(25) keV, respectively, and an excitation energy of 35.8(35) keV, behaves as an astromer during neutron capture in the 𝑖-process and in the 𝑟-process.

isomer decays↗

Thermal emittance and lifetime of alkali-antimonide photocathodes grown on GaAs and molybdenum substrates evaluated in a –300 kV dc photogun

In this work, Cs x K y Sb photocathodes grown on GaAs and molybdenum substrates were evaluated using a –300 kV dc high voltage photogun and diagnostic beam line. Photocathodes grown on GaAs substrates, with varying antimony layer thickness (estimated range from <20 nm to >1 um), yielded similar thermal emittance per rms laser spot size values (~0.4 mmmrad=mm) but very different operating lifetime. Similar thermal emittance was obtained for a photocathode grown on a molybdenum substrate but with markedly improved lifetime. For this photocathode, no decay in quantum efficiency was measured at 4.5 mA average current and with peak current 0.55 A at the photocathode.

43 PARTICLE ACCELERATORS↗

Charge carrier effective mass and concentration derived from combination of Seebeck coefficient and Te 125 NMR measurements in complex tellurides

Thermoelectric materials utilize the Seebeck effect to convert heat to electrical energy. The Seebeck coefficient (thermopower), S, depends on the free (mobile) carrier concentration, n, and effective mass, m*, as S ~ m*/n 2/3 . The carrier concentration in tellurides can be derived from 125 Te nuclear magnetic resonance (NMR) spin-lattice relaxation measurements. The NMR spin-lattice relaxation rate, 1/T 1 , depends on both n and m* as 1/T 1 ~(m*) 3/2 n (within classical Maxwell-Boltzmann statistics) or as 1/T1~(m*) 2 n 2/3 (within quantum Fermi-Dirac statistics), which challenges the correct determination of the carrier concentration in some materials by NMR. Here it is shown that the combination of the Seebeck coefficient and 125 Te NMR spin-lattice relaxation measurements in complex tellurides provides a unique opportunity to derive the carrier effective mass and then to calculate the carrier concentration. This approach was used to study Ag x Sb x Ge 50–2x Te 50 , well-known GeTe-based high-efficiency tellurium-antimony-germanium-silver thermoelectric materials, where the replacement of Ge by [Ag+Sb] results in significant enhancement of the Seebeck coefficient. Thus, values of both m* and n derived using this combination show that the enhancement of thermopower can be attributed primarily to an increase of the carrier effective mass and partially to a decrease of the carrier concentration when the [Ag+Sb] content increases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Suppressing the spin relaxation of electrons in silicon

Uniaxial compressive strain along the [001] direction strongly suppresses the spin relaxation in silicon. When the strain level is large enough so that electrons are redistributed only in the two valleys along the strain axis, the dominant scattering mechanisms are quenched and electrons mainly experience intra-axis scattering processes (intravalley or intervalley scattering within valleys on the same crystal axis). In this work, we first derive the spin-flip matrix elements due to intra-axis electron scattering off impurities, and then provide a comprehensive model of the spin relaxation time due to all possible interactions of conduction-band electrons with impurities and phonons. We predict a nearly three orders of magnitude improvement in the spin relaxation time of ~10 19 cm -3 antimony-doped silicon (Si:Sb) at low temperatures.

36 MATERIALS SCIENCE↗

Resonant Oscillation of Misch-Metal Atoms in Filled Skutterudites

We investigate vibrational behaviors in misch-metal filled antimony skutterudites in the time domain. At higher filling ratios of guest atoms, the vibration frequency approaches that of the cage structure and the amplitude becomes stronger. Furthermore, the reduction of lattice thermal conductivity over a wide temperature range can be explained using the measured resonant vibrational frequency. These findings reveal that the reduction of the lattice thermal conductivity is a result of scattering of acoustic phonons due to the resonant interaction between guest atoms and lattice phonons.

Physics↗

Dimensionally driven crossover from semimetal to direct semiconductor in layered SbAs

Two-dimensional (2D) materials have attracted a great deal of attention because they exhibit intriguing physical and chemical properties with great potential applications in electronic and optoelectronic devices, and even energy conversion. Due to the high anisotropy and unique crystal structure of layered materials, the properties can be effectively tuned by simply reducing dimensions to 2D. In this work, a unique 2D semiconductor, namely, monolayered SbAs, with high stability and indirect band gap, is predicted on the basis of first-principles calculations together with cluster expansion and Monte Carlo simulations. Interestingly, although the bulk antimony arsenide compound SbAs is known to exhibit semimetallic behavior, our calculations find that it is transformed into a direct semiconductor with a band gap of 1.28 eV when thinned down to a single atomic layer. The monolayer with antisite defects is transformed from indirect into a direct band-gap semiconductor. Such dramatic changes in the electronic structure could pave the way for SbAs to play a role in electronic device applications. Moreover, we find that the interlayer interactions in SbAs lead to a higher exfoliation energy than typical transition metal dichalcogenides such as MoS 2 , and hence we suggest that chemical deposition methods might be better than mechanical exfoliation methods for obtaining monolayer samples.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Weyl semimetal phases and intrinsic spin-Hall conductivity in SbAs ordered alloys

Here, using density functional theory calculations, we investigated possible Weyl semimetal (WSM) phases in antimony arsenide ordered alloys Sb 1-x ⁢As x (x=0, 1/6, 1/3, 1/2, 2/3, 5/6, 1). We find WSM phases for all As compositions of Sb 1-x ⁢As x with broken inversion symmetry, in contrast to Bi 1-x⁢ Sb x where only compositions x=1/2 and 5/6 were predicted to exhibit WSM phases. The WSM phases in Sb 1-x ⁢As x are characterized by the presence of 12 Weyl points, located within 55 meV from the Fermi level in the case of x = 1/2. The robust spin-orbit coupling strength and Berry curvature in these alloys produce large spin-Hall conductivity in the range of 176–602 ($\hslash$/e)(S/cm), comparable to that in the BiSb alloys. Finally, Sb 0.5 ⁢As 0.5 is predicted to be almost lattice matched to GaAs(111), with the Fermi level within the gap of the semiconductor, facilitating growth and characterization, and thus, offering promising integration with conventional semiconductors.

36 MATERIALS SCIENCE↗

Recent Advancements in Reconfigurable mmWave Devices Based on Phase-Change and Metal Insulator Transition Materials

Chalcogenide Phase Change Materials (PCM) and metal insulator transition (MIT) materials are a group of materials that are capable of switching between low resistance and high resistance states. These emerging materials have been widely used in optical storage media and memory devices. Over the past recent years, there have been interests in exploiting the PCM and MIT materials, especially germanium antimony telluride (GST) alloys and vanadium dioxide (VO 2 ), for radio frequency (RF) applications. The PCM and MIT-based RF devices are expected to bridge the gap between semiconductor switches and microelectromechanical system (MEMS) switches as they combine the low insertion loss performance of MEMS technology and the small size and reliability performance of semiconductor technology. This article presents an overview of the PCM and MIT materials for RF circuits and discusses the recent advancements in reconfigurable millimeter-wave (mmWave) devices based on PCM and MIT materials in depth.

36 MATERIALS SCIENCE↗

Investigation of Sb-Containing Precursors for Cu(In, Ga)Se2 Thin Films Through Design of Experiments

The Design of Experiments (DoE) module in JMP statistical software was used to determine the best parameters for Sb-containing CIGS precursors with a fixed selenization step. Solar cells were fabricated and measured for all completed films. The most important factor influencing the current-voltage device parameters was identified as the temperature and antimony flux interaction. The DoE prediction profiler and predictive contour plots provided guidance to further improve the device parameters. In one follow-up run, we increased device efficiency from 14.9% to 15.5% Additional gains in efficiency to 16.9% were realized by introducing an intentional Ga gradient and an antireflective coating.

14 SOLAR ENERGY↗

Solid-phase heteroepitaxy of oriented Sb 2 Se 3 on GaAs for birefringent thin films

Here, we investigate the amorphous-to-crystalline transformation of antimony selenide (Sb 2 Se 3 ) on UHV-prepared GaAs (001) substrates. In the bulk orthorhombic form, Sb 2 Se 3 is a layered quasi-1D semiconductor with highly anisotropic properties of interest for optical and electronic devices. We find that an amorphous layer deposited by molecular beam epitaxy annealed at or above 230 °C yields a textured-epitaxial structure among some randomly oriented domains. The textured-epitaxial Sb 2 Se 3 grains are oriented with the covalently bonded “1D axis” constrained in-plane to GaAs [110] and with multiple van der Waals (hk0) orientations out-of-plane. The same texture was achieved exclusively without randomly oriented grains using continuous-wave laser radiation, highlighting the use of thermal and optical methods to yield anisotropic crystalline Sb 2 Se 3 films directly from the amorphous phase. Polarized reflectance and polarized microscopy confirm the unique state of in-plane birefringence in the crystallized thin film. Overall, we show that solid-phase heteroepitaxy provides additional pathways to the integration of low-symmetry chalcogenide semiconductors for demanding applications where the inherent anisotropy needs to be preserved.

Xiao, Kelly [Stanford Univ., CA (United States)] (↗

Shape regulation of high-index facet nanoparticles by dealloying

Tetrahexahedral particles (~10 to ~500 nanometers) composed of platinum (Pt), palladium, rhodium, nickel, and cobalt, as well as a library of bimetallic compositions, were synthesized on silicon wafers and on catalytic supports by a ligand-free, solid-state reaction that used trace elements [antimony (Sb), bismuth (Bi), lead, or tellurium] to stabilize high-index facets. Both simulation and experiment confirmed that this method stabilized the {210} planes. A study of the PtSb system showed that the tetrahexahedron shape resulted from the evaporative removal of Sb from the initial alloy—a shape-regulating process fundamentally different from solution-phase, ligand-dependent processes. The current density at a fixed potential for the electro-oxidation of formic acid with a commercial Pt/carbon catalyst increased by a factor of 20 after transformation with Bi into tetrahexahedral particles.

Huang, Liliang (ORCID:0000000234740846)↗