Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “uranium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Dose estimation to a worker hand from depleted uranium handling - 25471

This work is a study of the dose to a hand from a depleted uranium (DU) slab. This research evaluates and compares the effective dose and localized skin-absorbed dose from handling depleted uranium. The analysis includes photons, neutrons, and beta particles emanating from depleted Uranium aged to 30 years. Although partial effective dose rates are small, the electron localized skin-absorbed dose rate is significant. These results may be used to check compliance with safety regulations, policies and procedures at the Los Alamos National Laboratory, and to build recommendations for the safe handling of depleted Uranium samples. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2015

Storage and concentration of plutonium and uranium solutions in LES 401 hot cell (ATALANTE) - criticality safety considerations - 14414

ATALANTE, located in Marcoule, is one of the main nuclear facilities of the French CEA (Atomic Energy and Alternative Energies Commission). The LES 401 hot cell was built in the 1980's and, since then, has been operating only with low masses of fissile material. As part of the management optimization for purified Uranium and Plutonium solutions ('Fin U Pu' Project), the new functions provided in LES 401 are now expected to be the following: - Reception of Uranium and Plutonium solutions, - Concentration of these solutions, - Storage of the concentrates and distillates. From the criticality safety point of view, the equipment was originally designed in safe geometry for Plutonium Nitrate, considering only a 2.5 cm -thick water reflector. However, the new criticality safety case had to take into account the following points: - Reception of not only Plutonium solutions, but also highly enriched Uranium solutions, - Considering flood risk as a possible contingency, - Considering precipitation as a possible contingency. These more conservative assumptions have meant introducing a mass limit for the cell, in addition to the geometry control mode. For the equipment containing very low concentrations of fissile material in normal operation, it was necessary, using the double contingency principle, to take a concentration limit into account in the specific situation of water flooding the cell. Finally, given the mass and geometry control mode, it was necessary to perform all the calculations with both fissile media (Plutonium and Uranium), as it was found that depending on the selected mass, geometry, and reflection conditions, the most penalizing media is not always the same. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Novel Synthesis and Characterization of Uranium-Zirconium Carbonitride by Direct Casting

UZrCN has exhibited thermophysical properties beneficial to high temperature reactor applications such as nuclear thermal rockets. The present work investigates a novel liquid phase synthesis method involving the admission of nitrogen gas during arc melting of uranium, zirconium, and carbon. Initial microstructural examinations using SEM indicated that the samples remain heterogenous with zirconium-rich cores in a uranium-rich matrix. Heterogeneity resulted from large differences in melting temperature of the major constituents and rapid solidification. Additional EDS, combustion analysis, and inert gas fusion analysis proved that the core regions have both uranium and zirconium and establish that carbon and nitrogen are retained during the fabrication process. XRD clarifies that the light elements did not form compounds with the uranium matrix but rather incorporated into the core region forming a sub-stoichiometric UZrCN. Heat treatment performed on equimolar U-Zr-C resulted in an increase in the homogenous phase present with an XRD pattern reflecting a ternary UZrCN despite small amounts of segregation in the final button.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Utilizing Gamma Signals to Find Optimal Uranium Wells

Uranium is a very important resource when using nuclear power. Only a small fraction of the uranium we use in the US is domestically sourced. Our goal is to effectively find and mine uranium in a way that is generally accurate and not difficult. Using computer science and machine learning, we want to automate a reasoning system that geologists use to analyze where the uranium ore bodies are. Presenting a general explanation of the goals and impacts of this project for the High School Intern showcase.

58 - GEOSCIENCES↗
DOE OSTI2025

On Uranium-Zirconium Carbonitride Formation by Direct Casting - A Novel Synthesis Study

UZrCN has exhibited thermophysical properties beneficial to high temperature reactor applications such as nuclear thermal rockets. The present work investigates a novel liquid phase synthesis method involving the admission of nitrogen gas during arc melting of uranium, zirconium, and carbon. Initial microstructural examinations using SEM indicated that the samples remain heterogenous with zirconium-rich cores in a uranium-rich matrix. Heterogeneity resulted from large differences in melting temperature of the major constituents and rapid solidification. Additional EDS, combustion analysis, and inert gas fusion analysis proved that the core regions have both uranium and zirconium and establish that carbon and nitrogen are retained during the fabrication process. XRD clarifies that the light elements did not form compounds with the uranium matrix but rather incorporated into the core region forming a sub-stoichiometric UZrCN. Heat treatment performed on equimolar U-Zr-C resulted in an increase in the homogenous phase present with an XRD pattern reflecting a ternary UZrCN despite small amounts of segregation in the final button.

36 - MATERIALS SCIENCE↗
DOE OSTI2014

Preliminary study on weapon grade uranium utilization in molten salt reactor miniFUJI

Preliminary study on weapon grade uranium utilization in 25MWth and 50MWth of miniFUJI MSR (molten salt reactor) has been carried out. In this study, a very high enriched uranium that we called weapon grade uranium has been employed in UF{sub 4} composition. The {sup 235}U enrichment is 90 - 95 %. The results show that the 25MWth miniFUJI MSR can get its criticality condition for 1.56 %, 1.76%, and 1.96% of UF{sub 4} with {sup 235}U enrichment of at least 93%, 90%, and 90%, respectively. In contrast, the 50 MWth miniFUJI reactor can be critical for 1.96% of UF{sub 4} with {sup 235}U enrichment of at smallest amount 95%. The neutron spectra are almost similar for each power output.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2015

The prospect of uranium nitride (UN) and mixed nitride fuel (UN-PuN) for pressurized water reactor

Design study of small Pressurized Water Reactors (PWRs) core loaded with uranium nitride fuel (UN) and mixed nitride fuel (UN-PuN), Pa-231 as burnable poison, and Americium has been performed. Pa-231 known as actinide material, have large capture cross section and can be converted into fissile material that can be utilized to reduce excess reactivity. Americium is one of minor actinides with long half life. The objective of adding americium is to decrease nuclear spent fuel in the world. The neutronic analysis results show that mixed nitride fuel have k-inf greater than uranium nitride fuel. It is caused by the addition of Pu-239 in mixed nitride fuel. In fuel fraction analysis, for uranium nitride fuel, the optimum volume fractions are 45% fuel fraction, 10% cladding and 45% moderator. In case of UN-PuN fuel, the optimum volume fractions are 30% fuel fraction, 10% cladding and 60% coolant/ moderator. The addition of Pa-231 as burnable poison for UN fuel, enrichment U-235 5%, with Pa-231 1.6% has k-inf more than one and excess reactivity of 14.45%. And for mixed nitride fuel, the lowest value of reactivity swing is when enrichment (U-235+Pu) 8% with Pa-231 0.4%, the excess reactivity value 13,76%. The fuel pin analyze for the addition of Americium, the excess reactivity value is lower than before, because Americium absorb the neutron. For UN fuel, enrichment U-235 8%, Pa-231 1.6% and Am 0.5%, the excess reactivity is 4.86%. And for mixed nitride fuel, when enrichment (U-235+Pu) 13%, Pa-231 0.4% and Am 0.1%, the excess reactivity is 11.94%. For core configuration, it is better to use heterogeneous than homogeneous core configuration, because the radial power distribution is better.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Uranium Bed Design Parameters for Tritium Plants Supporting Fusion Reactors

Uranium hydride is commonly used to store hydrogen or its isotopes in a solid state. The Self-Assaying Tritium Accountancy and Containment Unit for ITER (STACI) is a 5.2-kg bed of depleted uranium (dU) capable of holding up to 33 mol of hydrogen or its isotopes. Here we summarize the data analysis of past experimental campaigns with STACI, with the aim of describing the kinetics and thermodynamics of the hydriding process. Computed tomography imaging was performed on STACI both before and after its experimental campaign, and a high degree of swelling was observed in the dU. Literature on studies in regard to the swelling of large (multikilogram) quantities of uranium hydride for storage applications was not identified during this study. Data from the experimental campaign, as well as data on the formation reaction, are presented. The authors hope to create an analytical model of STACI based on these data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2017

Some Thermodynamic Features of Uranium–Plutonium Nitride Fuel in the Course of Burnup

Calculation studies on the effect of carbon and oxygen impurities on the chemical and phase compositions of nitride uranium–plutonium fuel in the course of burnup are performed using the IVTANTHERMO code. It is shown that the number of moles of UN decreases with increasing burnup level, whereas UN{sub 1.466}, UN{sub 1.54}, and UN{sub 1.73} exhibit a considerable increase. The presence of oxygen and carbon impurities causes an increase in the content of the UN{sub 1.466}, UN{sub 1.54} and UN{sub 1.73} phases in the initial fuel by several orders of magnitude, in particular, at a relatively low temperature. At the same time, the presence of impurities abruptly reduces the content of free uranium in unburned fuel. Plutonium in the considered system is contained in form of Pu, PuC, PuC{sub 2}, Pu{sub 2}C{sub 3}, and PuN. Plutonium carbides, as well as uranium carbides, are formed in small amounts. Most of the plutonium remains in the form of nitride PuN, whereas unbound Pu is present only in the areas with a low burnup level and high temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

RAPID QUANTITATION OF URANIUM FROM MIXED FISSION PRODUCT SAMPLES

Chemical similarities between U(VI) and Mo(VI) create challenges for separation and quantification of uranium from a mixed fission product sample. The purpose of this work was to demonstrate the feasibility of using Eichrom’s® UTEVA resin in addition to a tellurium spontaneous deposition to improve the quantitation of 235U using gamma spectroscopy. The optimized method demonstrated a consistent chemical yield of 74 ± 3 % for uranium. This procedure was evaluated using 1.41x1012 fissions produced from an irradiated HEU sample. The uranium was isotopically yielded by HPGe, and the minimum detectable activity (MDA) determined from the gamma spectra. The MDA for 235U, 237U, and 238U was reduced by a factor of two. The chemical isolation of uranium was successfully achieved in less than four hours, with a separation factor of 1.41x105 from molybdenum.

Haney, Morgan M.↗
DOE OSTI2025

Rapid separation of radiopure yttrium-91 for tracer studies from mixed fission products and uranium

A novel, single step method for isolating 91 Y from irradiated uranium and mixed fission products has been developed based on the commercially available Eichrom LN resin. The separation procedure allows for loading an LN resin column with an irradiated uranium solution, containing mixed fission products, in dilute HCl where both uranium and yttrium are retained on the resin. Eluting dilute (0.5–1 M) HCl will strip the majority of fission products. Furthermore, increasing the concentration to 3 M HCl will elute 91 Y without the presence of any other fission products. Finally, uranium can be recovered by passing concentrated HCl through the column.

Chromatography↗
DOE OSTI2021

Multicomponent pyrochlore solid solutions with uranium incorporation – A new perspective of materials design for nuclear applications

Multicomponent pyrochlore solid solutions with and without uranium incorporation were fabricated and their thermal-mechanical properties were characterized. Multicomponent pyrochlore solid solutions without uranium exhibit comparable thermal conductivity and higher mechanical strength compared to baseline single component rare-earth titanate pyrochlore (A 2 Ti 2 O 7 ). Uranium incorporation reduces hardness as compared with single component compositions. High entropy pyrochlore with uranium displays the highest thermal conductivity within multicomponent pyrochlore solid solutions with significantly better mechanical properties than UO 2 . The measured thermal conductivity correlates well with A-site cation mixing entropy and a modified size disorder parameter, and thus the size disorder and mixing entropy could be good indicators for predicting thermal conductivity of multicomponent pyrochlore solid solutions. This work opens up the possibility of designing multicomponent oxide solid solutions by controlling their chemical disorder/mixing entropy to achieve acceptable thermal-mechanical properties, desired radiation and corrosion performance for potential nuclear waste form and inert matrix fuel applications.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

First-principles investigation of uranium mononitride (UN): Effect of magnetic ordering, spin-orbit interactions and exchange correlation functional

Uranium mononitride (UN) is a promising nuclear fuel that combines the advantageous properties of readily used UO 2 and uranium alloys. Various properties of UN have been previously studied using different density functional theory (DFT) methodologies; however, there are still inconsistencies when it comes to the dynamical stability and defect properties of UN. We address these inconsistencies by studying the UN phonons and defect properties using DFT calculations employing two generalized gradient approximation (GGA) exchange-correlation functionals: PBE and AM05, with and without an added on-site Coulomb repulsion term (+U). Furthermore, we investigate the importance of spin-orbit coupling (SOC) when calculating the properties of UN. We use the different methodologies to determine the preference of UN to have antiferromagnetic (AFM) ordering, as seen in experiments, or ferromagnetic (FM) ordering of the uranium spins. We compare the crystallographic properties, density of states, the DFT X-ray photoelectron spectra and phonon dispersions calculated using the different methodologies. We demonstrate that GGA + U reproduces the AFM ordering in UN, but the crystal structure is dynamically unstable. We also show that magnetic ordering is important in finding the lowest energy defective structure, and that SOC has a distinct influence on the energy of the different uranium interstitial defects. Lastly, we discuss the point defect formation energies under U-rich and N-rich conditions, and the stoichiometric formation energies calculated with the different methodologies, providing insight into the observed tendency for forming hypostoichiometric UN.

36 MATERIALS SCIENCE↗
DOE OSTI2018

FRAM v5.2 estimation of plutonium and uranium isotopics using digitized 3-D position-sensitive CdZnTe detectors

Gamma-ray spectroscopy is an important tool used in international safeguards to measure plutonium and uranium isotopics. Recently developed, digital, 3-D position-sensitive CdZnTe gamma-ray spectrometers are promising for safeguards, offering improved performance over commonly available CdZnTe systems, with energy resolutions approaching that of high-purity germanium. CdZnTe gamma-ray spectra from plutonium and uranium samples were processed using the commercially available software FRAM v5.2, a tool that estimates plutonium and uranium isotopics from high-purity germanium spectra, across a wide range of materials. Furthermore using digital CdZnTe systems 239 Pu/ 240 Pu isotopic composition and effective 240 Pu percentage are evaluated to within less than 3 sigma statistical measurement uncertainty across reactor to weapons-grade samples, while low and highly-enriched uranium are easily distinguished.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2017

Materials for the Recovery of Uranium from Seawater

More than 1000× uranium exists in the oceans than exists in terrestrial ores. With nuclear power generation expected to increase over the coming decades, access to this unconventional reserve is a matter of energy security. With origins in the mid-1950’s, materials have been developed for the selective recovery of seawater uranium for more than six decades, with a renewed interest in particular since 2010. This review comprehensively surveys materials developed from 2000 – 2016 for recovery of seawater uranium, in particular including recent developments in inorganic materials, polymer adsorbents and related research pertaining to amidoxime, and nanostructured materials such as metal-organic frameworks, porous-organic polymers, and mesoporous carbons. In conclusion, challenges of performing reliable and reproducible uranium adsorption studies are also discussed, as well as the standardization of parameters necessary to ensure valid comparisons between different adsorbents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

A poly(acrylonitrile)-functionalized porous aromatic framework synthesized by atom-transfer radical polymerization for the extraction of uranium from seawater

In order to ensure a sustainable reserve of fuel for nuclear power generation, tremendous research efforts have been devoted to developing advanced sorbent materials for extracting uranium from seawater. In this work, a porous aromatic framework (PAF) was surface-functionalized with poly(acrylonitrile) through atom-transfer radical polymerization (ATRP). Batches of this adsorbent were conditioned with potassium hydroxide (KOH) at room temperature or 80 °C prior to contact with a uranium-spiked seawater simulant, with minimal differences in uptake observed as a function of conditioning temperature. A maximum capacity of 4.81 g-U/kg-ads was obtained following 42 days contact with uranium-spiked filtered environmental seawater, which demonstrates a comparable adsorption rate. A kinetic investigation revealed extremely rapid uranyl uptake, with more than 80% saturation reached within 14 days. Furthermore, relying on the semiordered structure of the PAF adsorbent, density functional theory (DFT) calculations reveal cooperative interactions between multiple adsorbent groups yield a strong driving force for uranium binding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Biogenic non-crystalline U (IV) revealed as major component in uranium ore deposits

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U (VI) ) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U (IV) generated through biologically mediated U (VI) reduction is the predominant U (IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (~58-89%) of U is bound as U (IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U (VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotope signatures, consistent with largely biotic reduction of U (VI) to U (IV) . This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U (IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.

58 GEOSCIENCES↗
DOE OSTI2022

Ultrafast laser filament-induced fluorescence for detecting uranium stress in Chlamydomonas reinhardtii

Abstract Plants and other photosynthetic organisms have been suggested as potential pervasive biosensors for nuclear nonproliferation monitoring. We demonstrate that ultrafast laser filament-induced fluorescence of chlorophyll in the green alga Chlamydomonas reinhardtii is a promising method for remote, in-field detection of stress from exposure to nuclear materials. This method holds an advantage over broad-area surveillance, such as solar-induced fluorescence monitoring, when targeting excitation of a specific plant would improve the detectability, for example when local biota density is low. After exposing C. reinhardtii to uranium, we find that the concentration of chlorophyll a, chlorophyll fluorescence lifetime, and carotenoid content increase. The increased fluorescence lifetime signifies a decrease in non-photochemical quenching. The simultaneous increase in carotenoid content implies oxidative stress, further confirmed by the production of radical oxygen species evidence in the steady-state absorption spectrum. This is potentially a unique signature of uranium, as previous work finds that heavy metal stress generally increases non-photochemical quenching. We identify the temporal profile of the chlorophyll fluorescence to be a distinguishing feature between uranium-exposed and unexposed algae. Discrimination of uranium-exposed samples is possible at a distance of $$\sim $$ ∼ 35 m with a single laser shot and a modest collection system, as determined through a combination of experiment and simulation of distance-scaled uncertainty in discriminating the temporal profiles. Illustrating the potential for remote detection, detection over 125 m would require 100 laser shots, commensurate with the detection time on the order of 1 s.

54 ENVIRONMENTAL SCIENCES↗