SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Aerodynamic force and moment coefficient data for parallel burn vehicle launch configurations tested in trisonic wind tunnel for static stability
Preliminary design and analysis of purge system concepts and purge subsystem approaches are defined and evaluated. Acceptable purge subsystem approaches were combined into four predesign layouts which are presented for comparison and evaluation. Two predesigns were selected for further detailed design and evaluation for eventual selection of the best design for a full scale test configuration. An operation plan is included as an appendix for reference to shuttle-oriented operational parameters.
Experimental aerodynamic investigations were conducted at the MSFC 14 x 14 inch trisonic wind tunnel on a .0044 scale model of the space shuttle orbiter, 110C. The test configurations included the orbiter alone and with external oxygen/hydrogen belly tanks. The six component aerodynamic force and moment data obtained cover a Mach number range from 0.6 to 4.96 at angles of attack from 10 to 60 deg at 0 deg sideslip angle and -10 to 10 deg at -6 deg sideslip angle. Reynolds number per unit length varied somewhat with Mach number but was a nominal 6.8 million per foot.
Air flowing from a convergent nozzle at pressure ratios greater than 2.5 has been split into eight separate jets by overexpansion of the flow into a divergent, eight-lobed passage. The splitting of the flow is accompanied by a decrease in the nozzle axial centerline Mach number. This in part is due to the radial inflow of secondary air between the lobes toward the nozzle centerline. Each of the smaller jets is partially split after it leaves the end of the divergent lobed section of the nozzle, thus creating a velocity profile having 16 peaks. At a pressure ratio of 3.5 the flow decelerates to Mach 1 in three convergent nozzle throat diameters. Convergent nozzle flow normally requires 12 diameters to reach Mach 1. The nozzle has a sound attenuation of 12 decibels with a thrust loss of 9 percent for the best configuration tested.
A developmental history of the Apollo lunar module landing and rendezvous radar subsystems is presented. The Apollo radar subsystems are discussed from initial concept planning to flight configuration testing. The major radar subsystem accomplishments and problems are discussed.
Experimental aerodynamic investigations were conducted in the NASA/MSFC 14 x 14 Inch Trisonic Wind Tunnel during January 1972 on 0.003366 and 0.00419 scale models of the MSFC space shuttle pressure fed booster configurations. The configurations tested were a 40 deg cone/cylinder/13 deg flare with and without fins, a 40 deg cone/cylinder/13 deg flare/9 deg flare with and without fins, a 35 deg cone/cylinder with and without fins, a 35 deg cone/cylinder/7 deg flare and a 35 deg cone/cylinder with straight extension. Six component aerodynamic force and moment data were recorded over a Mach number range of 0.9 to 5.0. Model angle of attack range was -10 to +10 deg and +20 to 80 at 0 deg sideslip. Model sideslip range was -10 to +10 deg at nominal angles of attack of 0, 30 and 51 deg
The effects of lift-roll coupling on the handling qualities of hovering VTOL aircraft using differential thrust for roll control were assessed in a piloted simulation study in the Ames six-degrees-of-freedom motion simulator. The configuration tested has three vertical thrust sources, one on the roll axis and two laterally displaced from the roll axis, with a thrust distribution of 25%/50%/25%. The outboard thrust sources were modulated to provide roll control whereas all three provided height control. Maximum thrust-to-weight ratio was varied together with a coupling parameter that combined roll-inertia, weight, and engine location. Results showed that handling qualities are affected not only by the occurrence of lift-roll coupling (dependent on both variables) but also by the severity of the coupling (dependent on the coupling parameter alone). However, the advantages of differential thrust for control can be retained with careful design.
An experimental investigation was conducted in which the behavior of liquid inflow to a cylindrical tank containing inlet baffles was observed during weightlessness. A single tank radius (2 cm), inlet radius (0.2 cm), and liquid (ethanol)were used. The inlet end of the tank was hemispherical with a 30 deg convergent inlet. All the baffle configurations tested were cylindrically symmetric and mounted coaxially with the tank within the hemispherical end. Both stable and unstable inflow behavior were observed using each baffle. It was found that, depending on which of the baffles was used, the critical inflow velocity at which a transition to unstable inflow began was from 2.5 to 12 times greater than the corresponding velocity in an unbaffled tank.
The metallic thermal protection system technology program for the space shuttle is reviewed for the areas of environmental uncertainties, materials data base, TPS design concepts and heat-shield panel configurations, testing and evaluation of materials, panels, and complete systems.
Fluid mechanics experiments were performed in cylindrical and spherical chambers to evaluate the simulated-fuel containment resulting from various injection geometry and inlet flow conditions for application to the open-cycle GNR. A preliminary study in the cylindrical chamber was directed toward developing inlet flow conditions which minimize mixing between the simulated fuel and propellant. Gas concentration measurements were obtained at several outer-stream to inner-stream weight flow and density ratios for the best inlet configuration tested in the preliminary study. The spherical cavity flow study was conducted to evaluate techniques for injecting simulated-fuel and propellant into a cavity.
A theoretical investigation was conducted to estimate the spectral properties of argon as a function of pressure, temperature, and wave number. The spectral characteristics of the argon buffer gas exert a strong influence on radiative energy transfer in the in-reactor test configuration of the nuclear light bulb engine. An existing computer program was modified and used to calculate the spectral absorption coefficients of argon at total pressures of 50, 100, 250, 500, 750 and 1000 atm in the temperature interval between 1000 and 30,000 K. At each pressure and temperature, spectral properties were calculated for forty-seven wave numbers in the interval between 1000 and 1,000,000 cm/1. Estimates of the spectral absorption coefficients of silicon were made as part of an evaluation of silicon vapor as a possible buffer-gas seeding agent for the reference nuclear light bulb engine. Existing cross-section data were used to calculate the spectral characteristics of silicon at twenty-four temperatures in the interval between 2000 and 10,000 K.
A turbine stator vane was tested in a two-dimensional cascade of 10 vanes and in a single-vane tunnel. The single-vane tunnel was a cold air version of a tunnel which will be used for high temperature heat transfer testing of cooled turbine vanes. The purpose of the investigation was to determine if the flow conditions in the single-vane tunnel were sufficiently similar to those of a 10-vane cascade to permit meaningful heat transfer testing. The vane was tested over a range of ideal exit critical velocity ratios. The principal measurements were vane surface static pressure and cross-channel surveys of exit static pressure, total pressure, and flow angle. A brief description of the test vane and tunnels is included. The results of the exit surveys, the vane surface pressure distributions, and overall performance in terms of flow and loss for the two test configurations are compared.
A highly suppressed TF-34 engine was used to investigate engine and flap interaction noise associated with an externally blown flap STOL powered lift system. Noise, efficiency, and velocity decay characteristics of mixed and separate flow exhaust systems including convergent, co-annular, and lobed designs were determined with the engine operating alone. Noise data were then obtained for several of the exhaust configurations with the engine blowing a wing-flap segment. Noise for both the engine alone and the engine with blown flaps showed substantial differences for the various exhaust configurations tested. The differences in observed noise are related primarily to nozzle effective exhaust velocity, flap impingement velocity, and noise spectral shape.
The incompressible-flow momentum theory is extended to the case of lifting fans. The resulting theory includes many of the known experimentally determined characteristics of fan-in-wing aircraft. These characteristics include the negligible effect of forward speed on fan thrust, the large momentum drag, and the generally inefficient performance throughout the transition speed range. Although mutual interference between the fans and the wing was totally neglected, the theory is confirmed by experimental results for the configuration tested. Examination of the results of an investigation of wall interference leads to the conclusion that the large fan-induced lift reported in many earlier investigations was largely the result of neglecting wall interference in the reduction of wind-tunnel data.
The data from an investigation of the aerodynamic characteristics of the expandable duct-jet flap concept are presented. The investigation was made using a large-scale model in the Ames 40- by 80-foot Wind Tunnel. The expandable duct-jet flap concept uses a lower surface, split flap and an upper surface, Fowler flap to form an internal, variable area cavity for the blowing air. Small amounts of blowing are used on the knee of the upper surface flap and the knee of a short-chord, trailing edge control flap. The bulk of the blowing is at the trailing edge. The flap could extend the full span of the model wing or over the inboard part only, with blown ailerons outboard. Primary configurations tested were two flap angles, typical of takeoff and landing; symmetric control flap deflections, primarily for improved landing performance; and asymmetric aileron and control flap deflections, for lateral control.
An investigation was made in the Langley Continuous Flow Hypersonic Tunnel at a Mach number of 10.3 to study the hypersonic aerodynamic characteristics of a Rockwell International shuttle orbiter configuration. Tests were made at a Reynolds number of 790,000 x 106 based on body length with an angle-of-attack range of 10 to 35 deg and sideslip variations of +1 to -9 deg. The effects of elevon and body flap deflection were investigated.
The drag caused by several vortex generating fuel injectors for scramjet combustors was measured in a Mach 2 to 3.5 airstream. Injector drag was found to be strongly dependent on injector thickness ratio. The distribution of helium injected into the stream was measured both in the near field and the far field of the injectors for a variety of pressure ratios. The far field results differed appreciably from measurements in the near field. Injection pressure ratio was found to profoundly influence the penetration. One of the aerowing configurations tested yielded low drag consistent with desirable penetration and spreading characteristics.
An investigation was made in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.9 and 2.86 to study the supersonic aerodynamic characteristics of a Rockwell International shuttle orbiter configuration. Tests were made at a Reynolds number of 1.5 million per foot with an angle-of-attack range of minus 4 to 28 deg and sideslip variations of minus 6 to 8 deg. The effects of elevon and aileron deflections were investigated.