Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “saturation temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Ferroic phase transitions and magnetoelectric coupling in cobalt doped BaTiO 3

Magnetoelectric (ME) materials exhibit interesting physics with cross coupling between ferroelectric and magnetic order parameters and thus strong potential to be utilized in memory, spintronics and other multifunctional electronic/magnetic devices. Doping of suitable transition metals in ferroelectrics can induce magnetism and ME coupling and modify the physical properties. Here, we report the structural, electronic, magnetic and ME coupling of 3.5, 5 and 7.5 mol% cobalt doped BaTiO 3 (BTO) ceramics. X-ray diffraction and Raman spectroscopy indicate that the samples are single phase having a tetragonal crystal structure with P4mm symmetry. The tetragonality ratio is found to decrease with increasing cobalt content. We observed a Fano-like asymmetric peak in the [A 1 (LO 1 )] Raman mode at ~173 cm -1 in all the cobalt doped BTO samples. The cobalt dopants are shown to be uniformly distributed throughout the surface of the samples. We observed a lowering of the ferroelectric transition temperature and increasing diffusivity parameter with increasing cobalt concentration. The electrical properties of all the samples have been investigated in detail by impedance spectroscopy and ac conductivity studies before and after the ferroelectric phase transitions. All the samples show hysteretic ferroelectric behavior with a clear saturation state that decreases with increasing cobalt content. The observed ferroelectricity in these samples is intrinsic in nature. The 3.5% cobalt doped BTO sample exhibits paramagnetic behavior whereas the 5 and 7.5% cobalt doped BTO samples show ferromagnetic ordering below 43 K. The 7.5% cobalt doped BTO samples show significant ME coupling.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Enhanced pedestal H-mode at low edge ion collisionality on NSTX

The Enhanced Pedestal (EP) H-mode regime is an attractive wide-pedestal high-βp scenario for the National Spherical Torus Experiment Upgrade (NSTX-U) and next-step devices as it achieves enhanced energy confinement (H98y,2 > 1.5), large normalized pressure (βN > 5), and significant bootstrap fraction (fBS > 0.6) at Ip/BT = 2 MA/T. This regime is realized when the edge ion collisionality becomes sufficiently small that a positive feedback interaction occurs between a reduction in the ion neoclassical energy transport and an increase in the particle transport from pressure-driven edge instabilities. The EP H-mode was most often observed as a transition following a large edge-localized mode in conditions with low edge neutral recycling. It is hypothesized that the onset of pressure-driven instabilities prior to the full recovery of the neutral density leads to a temporary period with an elevated ion temperature gradient that triggers the transition to EP H-mode. Linear CGYRO and M3D-C1 calculations are compared to beam emission spectroscopy and magnetic spectroscopy in order to describe the evolution of the edge particle transport mechanisms during the ELM recovery and the saturated EP H-mode state. The observations are consistent with the hypothesis that the onset of pressure-driven edge instabilities, such as the kinetic ballooning mode and kink-peeling mode, can be responsible for the increased particle transport in EP H-mode.

Battaglia, D. J. (ORCID:0000000188979740)↗
DOE OSTI2020

Electron–phonon coupling enhancement and displacive magnetostructural transition in SrCr 2 As 2 under magneto-Raman spectroscopy

Here, a Raman spectroscopy study on high quality single crystals of SrCr 2 A s 2 (SCA) in the temperature T range 4 K < T < 300 K and high applied magnetic fields up to H = 9 T is presented. The chromium B 1g phonon analysis reveals two anomalous shifts in the frequency, the first below T = 250 K at H = 0 T in the saturated AFM G -type order likely due to an enhanced electron–phonon coupling by the magnetic order, whereas the second anomaly occurs above H = 4 T at T = 4 K likely as a consequence of a magnetostructural displacive transition. Renormalization of the electronic Raman spectra in both studies reveals a decrease in the electronic density of states with decreasing T and increasing H , respectively, with consequent changes in the Fermi surface, which are intrinsically related to the observed anomalies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Spatial profile of argon (1s 5 ) metastables in an electron beam generated plasma

Electron beams with an applied magnetic field generate a secondary cold plasma with a selective chemical composition, featuring low-energy ions and metastable species in the discharge periphery, ideal for low-damage plasma treatment of material substrates. In this work, we studied the plasma generated by an e-beam using a 4 kV voltage in a pure argon gas environment under a magnetic field of 150 G and in the pressure range of 25–90 mTorr. We measured the absolute spatial density profile of argon (1 s 5 ) metastables in an electron beam generated plasma by laser-induced fluorescence and found it to be of the order of 10 16 m −3 . The electron temperature and the electron density measured by a Langmuir probe were of the order of 10 16 m −3 and less than an eV respectively. Electron-impact quenching was identified as a significant loss mechanism for the Ar(1s 5 ) state, leading to the saturation of the metastable density at higher pressures. Outside the primary ionization region, the spatial distribution of argon metastables followed a linear diffusion profile, indicating negligible additional production in those regions.

EEDF↗
DOE OSTI2020

Ferrimagnetism in EuFe 4 As 12 revealed by 153 Eu NMR and 75 As NQR measurements

Filled skutterudite compound EuFe 4 As 12 shows the highest magnetic ordering temperature of T C =154K among Eu-based skutterudite compounds, but its magnetic ground state has not been determined yet. In this study, we performed 153 Eu nuclear magnetic resonance (NMR) and 75 As nuclear quadrupole resonance (NQR) measurements on EuFe 4 As 12 to reveal its magnetic ground state as well as the physical properties from a microscopic point of view. From the temperature and magnetic field dependence of 153 Eu NMR spectrum in the magnetically ordered state, we found that the Eu ions are in Eu 2+ state with a nearly 7 μB corresponding to S=7/2 spins. Combined with the magnetization measurements, which show the reduced saturation moments of 4.5 μB/f.u., we determined the ground magnetic structure in EuFe 4 As 12 to be ferrimagnetic where the Eu 2+ 4f and the Fe 3d ordered moments are ferromagnetically aligned in each sublattice but the moments between the sublattices are antiferromagnetically aligned. We also found the local distortion at the Eu site from the cubic symmetry in the magnetically ordered state. The relationship between the rattling motion of Eu atoms and the local symmetry of the Eu ions is discussed. From the 75 As NQR nuclear spin-lattice relaxation time measurements as well as 153 Eu NMR measurements, we found that the 4f electrons of the Eu ions are well described by the local moment picture in both the magnetic and paramagnetic metallic states.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Absolute stimulated Raman side scatter in direct-drive laser-produced plasmas

Production of suprathermal electrons by stimulated Raman scattering (SRS) is a principal concern for contemporary direct-drive inertial confinement fusion experiments at the National Ignition Facility and similar systems since such electrons penetrate and preheat the target core, preventing efficient implosion. The higher temperatures and longer scale lengths in these experiments favor SRS over two-plasmon decay, which predominated in earlier experiments. In particular, current experiments are expected to exceed the threshold for absolute Raman side scatter, which would then dominate the interaction since it grows temporally until saturated by nonlinear mechanisms such as hot-electron production. Until recently, analyses of SRS side scatter have treated the case of a single laser beam incident on a plasma, but the direct-drive approach to laser fusion employs a multitude of beams to drive the implosion. Here in this paper, we present an analysis that can be applied to an arbitrary number of beams with varied angles of incidence and polarizations. In the case of a single beam, it allows a physically motivated derivation and verification of an analytic threshold formula. In the general case of multiple beams and arbitrary orientation and polarizations, the threshold is found by numerical integration of a set of first-order linear partial differential equations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

BBN catalysis by doubly charged particles

Abstract We consider primordial nucleosynthesis in the presence of hypotheticalquasi-stable doubly charged particles. Existence ofX –– withmacroscopic lifetimes will lead to the formation of its bound states with 4 He and otherlight elements, significantly facilitating the subsequentformation of lithium nuclei. From observational constraints on maximumallowable amount of lithium, that we update in this work, we derivestrong constraints on the abundance and lifetime ofX –– . In alikely cosmological freeze-out scenario with temperatures initiallyexceeding the mass ofX –– , the BBN constrains the lifetime of theseparticles to be less than about 100 seconds. For parametrically longlifetimes, lithium abundance data constrainX –– abundance to be lessthan 10 -9 relative to protons, regardless of whether these particlesdecay or remain stable. Stable particles could saturate the dark matterdensity only if their mass is comparable to or in excess of10 10 GeV, and most ofX –– will be found in bound states withberyllium nuclei, so that chemically they would appear as abnormallyheavy helium isotopes.

Astronomy & Astrophysics↗
DOE OSTI2020

Enhanced Pedestal H-mode at low edge ion collisionality on NSTX

The Enhanced Pedestal (EP) H-mode regime is an attractive wide-pedestal ELM-free high-betap scenario for NSTX-U and next-step devices as it achieves enhanced energy confinement (H98y,2 > 1.5), large normalized pressure (betaN > 5) and significant bootstrap fraction (f_BS > 0.6) at I_p/B_T = 2 MA/T. This regime is realized when the edge ion collisionality becomes sufficiently small that a positive feedback interaction occurs between a reduction in the ion neoclassical energy transport and an increase in the particle transport from pressure-driven edge instabilities. EP H-mode was most often observed as a transition following a large ELM in conditions with low edge neutral recycling. It is hypothesized that the onset of pressure-driven instabilities prior to the full recovery of the neutral density leads to a temporary period with elevated ion temperature gradient that triggers the transition to EP H-mode. Linear CGYRO and M3D-C1 calculations are compared to beam emission spectroscopy (BES) and magnetic spectroscopy in order to describe the evolution of the edge particle transport mechanisms during the ELM recovery and the saturated EP H-mode state. The observations are consistent with the hypothesis that the onset of pressure-driven edge instabilities, such as the KBM and kink-peeling, can be responsible for the increased particle transport in EP H-mode.

edge and boundary physics↗
DOE OSTI2023

Optimized purification methods for metallic contaminant removal from directly recycled Li-ion battery cathodes

Metallic contaminants pose a significant challenge to the viability of directly recycling Li-ion batteries. To date, few strategies exist to selectively remove metallic impurities from mixtures of shredded end-of-life material (black mass; BM) without concurrently damaging the structure and electrochemical performance of the target active material. We herein present tailored methods to selectively ionize two major contaminants—Al and Cu—while retaining a representative cathode (LiNi 0.33 Mn 0.33 Co 0.33 O 2 ; NMC-111) intact. This BM purification process is conducted at moderate temperatures in a KOH-based solution matrix. We rationally evaluate approaches to increase both the kinetic corrosion rate and the thermodynamic solubility of Al 0 and Cu 0 , and evaluate the impact of these treatment conditions on the structure, chemistry, and electrochemical performance of NMC. Specifically, we explore the impacts of chloride-based salts, a strong chelating agent, elevated temperature, and sonication on the rate and extent of contaminant corrosion, while concurrently evaluating the effects on NMC. The reported BM purification process is then demonstrated on samples of “simulated BM” containing a practically relevant 1 wt% concentration of Al or Cu. Increasing the kinetic energy of the purifying solution matrix through elevated temperature and sonication accelerates the corrosion of metallic Al and Cu, such that ∼100% corrosion of 75 μm Al and Cu particles is achieved within 2.5 hr. Further, we determine that effective mass transport of ionized species critically impacts the efficacy of Cu corrosion, and that saturated Cl – hinders rather than accelerates Cu corrosion by increasing solution viscosity and introducing competitive pathways for Cu surface passivation. The purification conditions do not induce bulk structural damage to NMC, and electrochemical capacity is maintained in half-cell format. Testing in full cells suggests that a limited quantity of residual surface species are present after treatment, which initially disrupt electrochemical behavior at the graphite anode but are subsequently consumed. Process demonstration on simulated BM suggests that contaminated samples—which prior to treatment show catastrophic electrochemical performance—can be recovered to pristine electrochemical capacity. The reported BM purification method offers a compelling and commercially viable solution to address contamination, particularly in the “fine” fraction of BM where contaminant sizes are on the same order of magnitude as NMC and where traditional separation approaches are unfeasible. Thus, this optimized BM purification technique offers a pathway towards viable direct recycling of BM feedstocks that would otherwise be unusable.

25 ENERGY STORAGE↗
DOE OSTI2026

The solubility of ErPO 4 and Er speciation in hydrothermal fluids at varying pH and salinity between 350 and 450 °C

The rare earth elements (REE) are important for the green-energy transition and can be incorporated into the REE phosphates, such as xenotime-(Y), which also hosts heavy REE (Tb– Lu). Xenotime-(Y) is a common accessory mineral in metamorphic rocks and a range of mineral deposits where it controls the mobility of heavy REE, however, the impact of high temperature aqueous fluids on the behavior of heavy REE is largely unknown. Thermodynamic modeling can be utilized as a tool to predict the mobility of REE in hydrothermal aqueous fluids, but must be supported by accurate experimental data. Here, we measured the solubility of endmember synthetic xenotime-structured ErPO4 in NaCl-HCl-NaOH-bearing aqueous solutions at 350 °C and water vapor saturation pressure, at 400 and at 450 °C and 500 bar using batch-type Inconel reactors. Erbium speciation was investigated as a function of pH from 2.8 to 8, where Er chloride species are predominant at acidic conditions (pH <3) and Er hydroxyl complexes are predominant at near- neutral to alkaline conditions (pH >3). At pH 7–9, the measured ErPO 4 solubility (-9.8 to -7.5 log m Er ) is up to 2.5 orders of magnitude lower than thermodynamic predictions (-9.4 to -6.7 log m Er ) using existing thermodynamic databases. At pH 2–3, the predicted ErPO 4 solubility is ~0.5 orders of magnitude higher at 350 °C and ~1 order of magnitude lower at 450 °C compared to experimentally measured Er concentrations. The thermodynamic properties of aqueous Er species were therefore revised in this study. The partial molal Gibbs energy of formation (Δ f G 0 T,P ) for aqueous Er hydroxyl and chloride species are optimized using GEMSFITS and the logarithmic formation constants (logβ n ( Cl,OH) ) were derived at each experimental temperature and pressure. The updated thermodynamic properties for Er hydroxyl species (Er(OH) +2 , Er(OH) 2 + , and Er(OH) 3 0 ) show that their stability shifts to more acidic conditions at and below 400 °C. The Er chloride species (ErCl +2 and ErCl 2 + ) show increased stability compared to Er hydroxyl species at temperatures of 450 °C and 0.01 mol/kg NaCl. The updated thermodynamic properties are implemented into the GEM-Selektor modeling package to investigate the mobility of Er in saline hydrothermal fluids in equilibrium with alkaline rocks. Importantly, the updated properties for Er hydroxyl species result in low Er solubility at rock equilibrated pH conditions due to an expanded hydroxyl predominance zone, but lower aqueous complex stability overall, whereas previous models suggest greater stability for aqueous Er species. Furthermore, ErPO 4 solubility increases with decreasing temperature due to the deprotonation of HCl, which increases the acidity of hydrothermal fluids and the availability of Cl - to complex with the REE. These simulations highlight how fluid-rock reaction and temperature affect the mobility of REE in hydrothermal ore-forming systems.

58 GEOSCIENCES↗
DOE OSTI2021

Critical pitting temperature of selective laser melted 316L stainless steel: A mechanistic approach

In this work, the critical pitting temperature (CPT) of selective laser melted (SLM) 316 L stainless steel in 1.0 M NaCl was measured and compared with a commercial wrought alloy. Potentiostatic measurements determined a mean CPT value of 16 ± 0.7 °C, 27.5 ± 0.8 °C and 31 ± 1 °C for the wrought alloy, the SLM alloy normal to the build direction and parallel to the build direction, respectively. The lead-in pencil electrode technique was used to study the pit chemistry of the two alloys and to explain the higher CPT values observed for the SLM alloy. A lower critical current density required for passivation in a simulated pit solution was measured for the SLM alloy. Moreover, the ratio of the critical concentration to saturated concentration of dissolving metal cations was found to be higher for the SLM alloy, which was related to its different salt film properties, possibly as a result of the SLM’s distinct microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

On the Thermodynamic Condition for Adsorption Azeotropes

Adsorption azeotropy is a common phenomenon in mixed-gas adsorption equilibria. Since the first literature report of binary adsorption azeotropes in 1933, numerous studies investigated the thermodynamic conditions for adsorption azeotropes but failed to reach definitive conclusions. Based on the generalized Langmuir isotherm model for multicomponent adsorption equilibria which takes into account the vacant site as part of the adsorbed phase, this study presents the thermodynamic condition for adsorption azeotropes as derived from the generalized Langmuir isotherm to be the equality of the ratios of adsorbed phase activity coefficient γi and adsorption equilibrium constant $K$$^{o}_{i}$ for the two adsorbates in the binary 1–2 adsorption system, i.e., γ 1 /$K$$^{o}_{1}$ = γ 2 /$K$$^{o}_{2}$. This adsorption azeotropic condition is analogous to the vapor–liquid equilibrium azeotropic condition, i.e., the equality of the products of liquid phase activity coefficient and saturation vapor pressure Pisat for the two components, i.e., γ 1 $P$$^{sat}_{1}$ = γ 2 $P$$^{sat}_{2}$. We validated the thermodynamic condition for adsorption azeotropes with 14 azeotrope-forming adsorption systems in this study. As a result, we investigated the effects of the pressure, temperature, and adsorbed phase nonideality on azeotrope formation.

42 ENGINEERING↗
DOE OSTI2024

Arctic Critical Infrastructure: Assessing and Predicting the Risk to Critical Permafrost Infrastructure from Climate Change: A New Thermomechanical Approach

This study presents the development of a computational framework designed to predict the interaction between permafrost and infrastructure, addressing potential failure modes and mitigation strategies in the context of climate change. The framework, rooted in advanced modeling and simulation (mod/sim) techniques, integrates thermomechanical coupling to account for the complex interplay between heat flow, ice content, and mechanical behavior in permafrost. Existing models fail to fully capture these dynamics, particularly as they relate to the effects of ice saturation on structural integrity. Our innovative Arctic Coastal Erosion (ACE) framework fills this gap by coupling thermal and mechanical models to accurately simulate subsidence and deformation in permafrost environments. We applied the ACE framework to a representative runway, demonstrating its capability to predict settlement due to rising temperatures and subsequent permafrost thaw. This proof-of-concept showcases the potential of the framework to evaluate risks to Arctic infrastructure, which supports over four million people and 70% of existing permafrost-based structures. By simulating various infrastructure types and environmental conditions, our research offers insights into failure mechanisms and evaluates structural solutions to mitigate risk. The anticipated deliverables, including a prototype runway exemplar, position this project as a critical advancement in permafrost infrastructure modeling, with applications in national security and resilience planning.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Suitable low Global Warming Potential (GWP) refrigerants for two-speed Heat Pumps for residential applications based on speed Heat Pumps for residential applications based on simulated performance simulated performance

Cold climate Heat Pumps (CCHPs) using single-speed compressors in tandem have been successfully built and tested to reach its performance metrics with outdoor temperatures as low as -25°C. CCHPs must be designed to alleviate the problems of too high discharge temperatures, low suction pressure and high-pressure ratio at low ambient conditions and insufficient heating capacity relative to the heating capacity at 8.3°C. In this paper we recognize those concerns. Low-GWP refrigerants are screened based on the shape of their T-S saturation boundary. Simulations of the performance of low-GWP refrigerants (R32, R454B, R466A, and R452B) relative to R410A is done using the DOE/ORNL Heat Pump Design Model at the component level. Systemic inefficiency, the root cause of lost work, is addressed by component-level exergy analysis to refine design options. CCHPs using low-GWP refrigerants addresses issues of reducing energy consumption, lowering carbon footprint, and enabling environmentally sustainability. The CCHP was designed to meet a HSPF > 11.0 and SEER > 15.0 having adequate heat pump heating capacity down to -25°C. It is estimated that at least 2.6 million U.S homes using electric furnaces and heat pumps in cold or very old climates with an annual energy consumption of 0.17EJ would benefit by CCHPs.

Ally, Moonis↗
DOE OSTI2021

Experimental investigation of elemental and isotopic evaporation processes by laser heating in an aerodynamic levitation furnace

In this report we carried out evaporation experiments on a B-type calcium–aluminium-rich inclusion (CAI) melt in a gas-mixing aerodynamic levitation laser furnace, at 1873 K and an oxygen partial pressure of 10 -9.1 atm, for durations ranging from 60 to 600 s. Evaporation of SiO 2 and MgO follow the same trend as those observed in vacuum furnace experiments at the same temperature and starting composition, showing that their evaporation relative to one another from the melt is independent of pressure, oxygen fugacity, and hydrodynamical regime specific to the furnace. Isotopic ratios of Mg and Si in evaporation residues are used to derive fractionation factors of α 26/24 Mg vap-liq = 0.9906± 0.0004 and α 30/28 Si vap-lip = 0.9943±0.0003, which are both significantly closer to unity than those found for evaporation in a vacuum, which translates to less isotope fractionation. The residues are also less isotopically fractionated than expected for cases in which transport of the gas species away from the melt is diffusion-controlled at 1-atm. By analysing the flow regimes in our furnace, we find that advection by the levitating gas is the primary mode of mass transport away from the melt surface, as opposed to diffusion-limited transport in a vacuum or 1-atm tube furnace. A modified Hertz–Knudsen–Langmuir formulation accounts for this process, and shows that isotopic fractionation of both Si and Mg reflect a saturation factor (ratio of the pressure of the evaporating species to vapour saturation pressure) equal to 0.75. This is in perfect accord with recent measurements of Cu isotopic fractionation using a similar furnace. The fact that three elements (Mg, Si, Cu) with varying equilibrium vapour pressures, activity coefficients in the liquid, and diffusion coefficients in the gas have the same scaling behaviour to saturation pressure is a strong indication that the mechanism controlling evaporation is driven by the hydrodynamical regime imposed in the furnace. Therefore, this class of experiments can be used to constrain processes in which advection dominates over diffusion, such as (but not limited to) planetary ejecta, tektites, giant impacts, nebular condensation in a turbulent flow, or nuclear fallout material. Finally, the possibility to reach high temperatures (in excess of 3500 K) in this furnace allows it to be used to evaluate the activity coefficients of melt components in extreme conditions relevant to molten planetary interiors (i.e., magma oceans), with a specific focus on refractory elements.

58 GEOSCIENCES↗
DOE OSTI2020

In-situ fabrication and transport properties of (111) Y 2 Ir 2 O 7 epitaxial thin film

We report on the successful fabrication of (111) oriented thin films of pyrochlore iridate Y 2 Ir 2 O 7 by means of solid phase epitaxy. Essentially, we developed an entirely in situ annealing protocol, which is superior to the conventional ex-situ routine that requires multi-hour annealing to stabilize the proper pyrochlore structure. The morphological quality of the films has been confirmed by x-ray diffraction, reflectivity, and reciprocal space mapping, demonstrating their high crystallinity with a pure pyrochlore phase and an expected epitaxial relation to the substrate. Strikingly, below the magnetic phase transition, the temperature dependence of resistivity shows a power-law behavior with the power exponent of similar to 3/2, characteristic of a Weyl semimetal in the presence of impurities and electron-electron correlations. Finally, below 10K, the magneto-transport measurements reveal the emergence of a non-saturated negative magnetoresistance up to 9T with a small "valley" around zero field. These findings are further interpreted in relation to the weak anti-localization effect and the non-collinear antiferromagnetic ordering on the Ir sublattice.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of carbon concentration on the local atomic structure of amorphous GST

Ge-Sb-Te (GST) alloys are leading phase-change materials for data storage due to the fast phase transition between amorphous and crystalline states. Ongoing research aims at improving the stability of the amorphous phase to improve retention. This can be accomplished by the introduction of carbon as a dopant to Ge 2 Sb 2 Te 5 , which is known to alter the short- and mid-range structure of the amorphous phase and form covalently bonded C clusters, both of which hinder crystallization. The relative importance of these processes as a function of C concentration is not known. Here we used molecular dynamics simulation based on density functional theory to study how carbon doping affects the atomic structure of GST-C. Carbon doping results in an increase in tetrahedral coordination, especially of Ge atoms, and this is known to stabilize the amorphous phase. We observe an unexpected, non-monotonous trend in the number of tetrahedral bonded Ge with the amount of carbon doping. Our simulations show an increase in the number of tetrahedral bonded Ge up to 5 at.% C, after which the number saturates and begins to decrease above 14 at.% C. The carbon atoms aggregate into clusters, mostly in the form of chains and graphene flakes, leaving less carbon to disrupt the GST matrix at higher carbon concentrations. Different degrees of carbon clustering can explain divergent experimental results for recrystallization temperature for carbon doped GST.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Role of the separatrix density in the pedestal performance in deuterium low triangularity JET-ILW plasmas and comparison with JET-C

A reduction of the pedestal pressure with increasing separatrix density over pedestal density (nesep/neped) has been observed in JET. The physics behind this correlation is investigated. The correlation is due to two distinct mechanisms. The increase of nesep/neped till ≈0.4 shifts the pedestal pressure radially outwards, decreasing the peeling-balloning stability and reducing the pressure height. The effect of the position saturates above nesep/neped ≈ 0.4. For higher values, the reduction of the pedestal pressure is ascribed to increased turbulent transport and, likely, to resistive MHD effects. The increase of nesep/neped above ≈0.4 reduces ∇ne/ne, increasing ηe and the pedestal turbulent transport. This reduces the pressure gradient and the pedestal temperature, producing an increase in the pedestal resistivity. The work suggests that the increase in resistivity might destabilize resistive ballooning modes, further reducing the pedestal stability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗