Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic crystals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

The response of thermally and optically stimulated luminescence from Al2O3:C to high-energy heavy charged particles

The thermoluminescence (TL) and optically stimulated luminescence (OSL) response of Al2O3 dosimeters to high-energy heavy charged particles (HCP) has been studied using the heavy ion medical accelerator at Chiba, Japan. The samples were Al2O3 single-crystal chips, of the type usually known as TLD-500, and Luxel(TM) dosimeters (Al2O3:C powder in plastic) from Landauer Inc. The samples were exposed to 4He (150 MeV/u), 12C (400 MeV/u), 28Si (490 MeV/us) and 56Fe (500 MeV/u) ions, with linear energy transfer values covering the range from 2.26 to 189 keV/micrometers in water and doses from 1 to 100 mGy (to water). A 90Sr/90Y beta source, calibrated against a 60Co secondary standard, was used for calibration purposes. For OSL, we used both continuous-wave OSL measurements (CW-OSL, using green light stimulation at 525 nm) and pulsed OSL measurements (POSL, using 532 nm stimulation from a Nd:YAG Q-switched laser). The efficiencies (eta HCP, gamma) of the different HCPs at producing OSL or TL were observed to depend not only upon the linear energy transfer (LET) of the HCP, but also upon the sample type (single crystal chip or Luxel(TM)) and the luminescence method used to define the signal--i.e. TL, CW-OSL initial intensity, CW-OSL total area, or POSL. Observed changes in shape of the decay curve lead to potential methods for extracting LET information of unknown radiation fields. A discussion of the results is given, including the potential use of OSL from Al2O3 in the areas of space radiation dosimetry and radiation oncology. c2004 Elsevier Ltd. All rights reserved.

Heavy Ions↗
DOE OSTI2021

Effects of polycarboxylate ether (PCE)-based superplasticizer on the dissolution and subsequent hydration of calcium oxide (CaO)

Calcium oxide (CaO) is an important construction material, used as expansive agent, alkaline activator, and repairing material for historical structures. In this study, the dissolution and subsequent hydration of CaO, with or without the polycarboxylate ether (PCE)-based superplasticizer, were investigated to elucidate the complex crystallization process of calcium hydroxide (Ca(OH){sub 2}). On contact with pure water, CaO particles began to hydrate within a few minutes, while releasing a significant amount of heat. Adding superplasticizer slowed such rapid heat evolution by forming a dormant period and significantly affected the crystallinity of the hydration product. The dormant period was controllable by the amount of added superplasticizer. Moreover, as a result of early nucleation of Ca(OH){sub 2}, the formation of 10–100-nm spherical nanoparticles was observed via an in-situ transmission electron microscope, which completely differed from the final crystal shape of the hydration product.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A molecular dynamics survey study of impact-induced amorphization in yttria nanoparticles

The impact of a single yttria (Y 2 O 3 ) nanoparticle onto a yttria substrate was studied as a function of particle velocity (300–1200 m/s) and diameter (5–12 nm) for three particle orientations and two substrate orientations using molecular dynamics simulations. Impacts resulted in minimal dislocation motion but extensive disordering of the crystal lattice without approaching the melting temperature. The resulting amorphous microstructure was both precisely coincident with plastic strain and retained until the end of the simulation, suggesting a deformation mechanism of amorphization-facilitated viscous flow. Further analysis revealed that the degree of amorphization depended primarily on the impact velocity and secondarily on the orientations of the particle and substrate, with significant second-order effects from variable interactions.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Effect of PBX prill size on the compressive properties of PBX 9502

Plastic-Bonded Explosive (PBX) prills are agglomerates a few millimeters in diameter composed of High Explosive crystals non-uniformly distributed in and surrounded by a polymer binder. When pressed at elevated temperatures at or above the binder melt temperature the polymer flows to uniformly coat the HE crystals to create a well-consolidated compaction. In reality it does so imperfectly, such that x-ray tomographic scans often look like a collection of prills mashed together. It is speculated that the larger the prill, the more non-uniform the binder distribution, but this has never been proven. Even if that were not so, the larger the prill the farther binder must flow toward the middle to homogenize during pressing. Thus, the degree of homogenization depends in part on prill size. The degree to which binder flows during pressing in turn affects the void distribution within pressed charges, which one suspects will affect shock sensitivity and material strength. In this paper we explore, for ~30 PBX 9502 formulation batches using the same TATB powder lot, how prill size affects the compressive mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of PBX Prill Size on the Compressive Properties of PBX 9502

Plastic-Bonded Explosive (PBX) prills are agglomerates a few millimeters in diameter composed of High Explosive crystals non-uniformly distributed in and surrounded by a polymer binder. When pressed at elevated temperatures at or above the binder melt temperature the polymer flows to uniformly coat the HE crystals to create a well-consolidated compaction. In reality it does so imperfectly, such that x-ray tomographic scans often look like a collection of prills mashed together. It is speculated that the larger the prill, the more non-uniform the binder distribution, but this has never been proven. Even if that were not so, the larger the prill the farther binder must flow toward the middle to homogenize during pressing. Thus, the degree of homogenization depends in part on prill size. The degree to which binder flows during pressing in turn affects the void distribution within pressed charges, which one suspects will affect shock sensitivity and material strength. In this paper we explore, for ~30 PBX 9502 formulation batches using the same TATB powder lot, how prill size effects the compressive mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Acoustic field positioning for containerless processing

The non-contact positioning of materials in a space processing chamber is accomplished using a new type of acoustic levitator. Liquid and solid materials are positioned using a single source of sound. Fine control of position may be obtained by motion of an acoustical reflector. Electrical power required is usually less than 100 watts. The system operates satisfactorily at high and low temperatures and is adaptable as an add-on feature to existing space experiments. Containerless melting and solidification can be performed and a freely suspended liquid can be shaped to the contour of the sound field. Experiments are described in which aluminum, glass and plastic materials are melted and solidified in the containerless state. The system has applications to containerless crystal growth, melting and related processes.

Whymark, R. R.↗
NASA NTRS1975

Acoustic field positioning for containerless processing

The noncontact positioning of materials in a space processing chamber is accomplished using a new type of acoustic levitator. Liquid and solid materials are positioned using a single source of sound. Fine control of position may be obtained by motion of an acoustical reflector. The electrical power required is usually less than 100 watts. The system operates satisfactorily at high and low temperatures and is adaptable as an 'add-on' feature to existing space experiments. Containerless melting and solidification can be performed and a freely suspended liquid can be shaped to the contour of the sound field. Experiments are described in which aluminum, glass and plastic materials are melted and solidified in the containerless state. The system has applications to containerless crystal growth, melting and related processes.

Whymark, R. R.↗
NASA NTRS1987

Deformation and fatigue behavior of SSME turbopump blade materials

Directionally solidified and single crystal superalloys which are intended for use as turbopump blade materials are anisotropic both elastically and plastically. Therefore, isotropic constitutive models must be modified. Several models which are now being developed are based on metallurgical theories of deformation in these types of alloys. However, these theories have not been fully justified, and the temperature and strain regimes over which they may be valid are poorly defined. The objective of this work is to study the deformation behavior of the alloys, in order to determine the validity of these models and to thereby support the ongoing research efforts in solid mechanics.

Milligan, Walter W.↗
NASA NTRS1999

Binary Colloidal Alloy Test Conducted on Mir

Colloids are tiny (submicron) particles suspended in fluid. Paint, ink, and milk are examples of colloids found in everyday life. The Binary Colloidal Alloy Test (BCAT) is part of an extensive series of experiments planned to investigate the fundamental properties of colloids so that scientists can make colloids more useful for technological applications. Some of the colloids studied in BCAT are made of two different sized particles (binary colloidal alloys) that are very tiny, uniform plastic spheres. Under the proper conditions, these colloids can arrange themselves in a pattern to form crystals. These crystals may form the basis of new classes of light switches, displays, and optical devices. Windows made of liquid crystals are already in the marketplace. These windows change their appearance from transparent to opaque when a weak electric current is applied. In the future, if the colloidal crystals can be made to control the passage of light through them, such products could be made much more cheaply. These experiments require the microgravity environment of space because good quality crystals are difficult to produce on Earth because of sedimentation and convection in the fluid. The BCAT experiment hardware included two separate modules for two different experiments. The "Slow Growth" hardware consisted of a 35-mm camera with a 250- exposure photo film cartridge. The camera was aimed toward the sample module, which contained 10 separate colloid samples. A rack of small lights provided backlighting for the photographs. The BCAT hardware was launched on the shuttle and was operated aboard the Russian space station Mir by American astronauts John Blaha and David Wolf (launched September 1996 and returned January 1997; reflown September 1997 and returned January 1998). To begin the experiment, one of these astronauts would mix the samples to disperse the colloidal particles and break up any crystals that might have already formed. Once the samples were mixed and the experiment was powered on, the hardware operated autonomously, taking photos of the colloidal samples over a 90-day period.

Hoffmann, Monica I.↗
NASA NTRS2018

Segregation-Assisted Plasticity in Ni-Based Superalloys

Correlative high resolution transmission electron microscopy and energy dispersive X-ray spectroscopy are used to study deformation-induced planar faults in the single crystal superalloy MD2 crept at 800°C and 650 MPa. Segregation of Cr and Co at microtwins, APBs, CISFs/SISFs and CESFs/SESFs is confirmed and quantified. The extent of this is found to depend upon the fault type, being most pronounced for the APB. The CESF/SESF is studied in detail due to its role as a precursor of the microtwins causing the majority of plasticity under these conditions. Quantitative modelling is carried out to rationalize the findings; the experimental results are consistent with a greater predicted velocity for the lengthening of the CESF/SESF { compared with the other types of fault { and hence confirm its role in the diffusion-assisted plasticity needed for the microtwinning mechanism to be operative.

Barba, D.↗
DOE OSTI2020

In situ indentation and high cycle tapping deformation responses in a nanolaminate crystalline/amorphous metal composite

The incorporation of nanostructured and amorphous metals into modern applications is reliant on the understanding of deformation and failure modes in constrained conditions. To study this, a 105 nm crystalline Cu/160 nm amorphous Cu 45 Zr 55 (at.%) multilayer structure was fabricated with the two crystalline layers sputter deposited between the top-middle-bottom amorphous layers and prepared to electron transparency. The multilayer was then in situ indented either under a single load to a depth of ~ 100 nm (max load of ~ 100 μN) or held at 20 μN and then repeatedly indented with an additional 5 μN up to 20,000 cycles in a transmission electron microscope to compare the deformation responses in the nanolaminate. For the single indentation test, the multilayer showed serrated load-displacement behavior upon initial indentation inductive of shear banding. Additionally, at an indentation depth of ~ 32 nm, the multilayer exhibited perfect plastic behavior and no strain hardening. Both indented and fatigue-indented films revealed diffraction contrast changes with deformation. Subsequent Automated Crystal Orientation Mapping (ACOM) measurements confirmed and quantified global texture changes in the crystalline layers with specifically identified grains revealing rotation. Using a finite element model, the in-plane displacement vectors under the indent mapped conditions where ACOM determined grain rotation was observed, indicating the stress flow induced grain rotation. Furthermore, the single indented Cu layers also exhibited evidence of deformation induced grain growth, which was not evident in the fatigue-indented Cu based multilayer. Finally, the single indented multilayer retained a significant plastic crater in the upper most amorphous layer that directly contacted the indenter; a negligible crater impression in the same region was observed in the fatigued tested multilayer. These differences are explained by the different loading methods, applied load, and deformation mechanisms experienced in the multilayers.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Interface morphology and dislocation-mediated processes during rapid solidification of thin films

Rapid solidification experiments have, in recent years, revealed a wealth of new microstructural phenomena that suggest a strong connection between the kinetics of solidification and the crystalline structures that emerge as a result. In this work, we investigate the interplay between interface morphology and defect-mediated processes during rapid solidification conditions using a Phase Field Crystal (PFC) model, enabling us to simultaneously and efficiently explore the physics of solidification and elasto-plasticity in the formalism of a single-field theory. We predict that there are two mechanisms by which dislocations emitted directly from the solid–liquid interface induce orientation gradients as well as the formation of subgrain boundaries within a single solidifying cell. We relate these mechanisms to the morphology of the moving solid–liquid interface and identify a suitable control parameter in the PFC model with which we can go between said morphologies by effectively changing the relative strength of the capillary length and kinetic coefficients of the solid–liquid interface. Thus, we are able to provide mechanistic explanations for several microstructural features (with an emphasis on orientation gradients and subgrain boundaries) observed during the rapid solidification of pure materials. We also provide a simple explanation for the formation of “jagged” subgrain boundaries, which is consistent with our experimental observations in rapidly solidified samples of Aluminum, whose mechanisms have thus far been unknown.

Interface morphology↗
NASA NTRS1990

Slow plastic deformation of extruded NiAl-10TiB2 particulate composites at 1200 and 1300 K

A dispersion of 1-micron TiB2 particles in the B2 crystal structure NiAl intermetallic can effectively increase its elevated temperature strength, in association with increasing deformation resistance with TiB2 volume fraction. Attention is presently given to alternative densification methods, which may increase the initial as-fabricated dislocation density and lead to enhanced elevated-temperature strength. The 'XD' extrusion method was used to produce NiAl with 10 vol pct TiB2. Although apparent extrusion defects were occasionally found, neither grain-boundary cracking nor particle-matrix separation occurred.

Whittenberger, J. D.↗
DOE OSTI2021

Composite binder, processing, and particle size effects on mechanical properties of non-hazardous high explosive surrogates

Plastic-bonded explosives (PBX) are polymer matrix composites that are highly loaded with micron-scale explosive crystals. The thermal and mechanical properties of these materials must be well-understood so that appropriate engineering models can be developed, but testing such properties under many scenarios can be hazardous and expensive. A non-hazardous PBX surrogate (“mock”) may be used in place of a PBX in many experiments if the thermomechanical properties are well-matched. Our previous research has shown that 5-iodo-2'-deoxyuridine (IDOX) is a promising crystalline filler material for the explosive cyclotetramethylene-tetranitramine (HMX). In this study, we investigate how the binder composition, variations in the IDOX particle size distribution, and pressing temperature affect the compressive strength and elastic modulus. We observe that while the binder system used in the composite dominates the mechanical response, the particle size distribution and pressing conditions do have a measurable effect on the material compliance and strength.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2022

Visualization and validation of twin nucleation and early-stage growth in magnesium

The abrupt occurrence of twinning when Mg is deformed leads to a highly anisotropic response, making it too unreliable for structural use and too unpredictable for observation. Here, we describe an in-situ transmission electron microscopy experiment on Mg crystals with strategically designed geometries for visualization of a long-proposed but unverified twinning mechanism. Combining with atomistic simulations and topological analysis, we conclude that twin nucleation occurs through a pure-shuffle mechanism that requires prismatic-basal transformations. Also, we verified a crystal geometry dependent twin growth mechanism, that is the early-stage growth associated with instability of plasticity flow, which can be dominated either by slower movement of prismatic-basal boundary steps, or by faster glide-shuffle along the twinning plane. The fundamental understanding of twinning provides a pathway to understand deformation from a scientific standpoint and the microstructure design principles to engineer metals with enhanced behavior from a technological standpoint.

36 MATERIALS SCIENCE↗
DOE OSTI2020

TATB ratchet growth and hydrostatically-confined PBX 9502

The explosive TATB (1,3,5-triamino-2,4,6-trinitirobenzene) is formulated with various polymeric binders to create plastic-bonded explosives like PBX 9502 (95 wt% TATB and 5 wt% Kel-F binder). TATB crystals are graphitic and plate-like in nature and single crystals exhibit anisotropic thermal expansion where the direction normal to the platelet surface grows 10-20 times more than the in-plane platelet direction. Compactions of TATB, with and without binder, exhibit irreversible volume expansion, also known as ratchet growth, when thermal cycled to hot or cold temperatures. Specifically, when TATB-based compactions return to ambient after a temperature excursion away from room temperature, the volume of the specimen is slightly larger. Repeated thermal cycles can reduce the density by 1 to 2%. Axial confinement on a cylindrical specimen has previously been shown by us to suppress growth in the confining direction but then increase growth in the unconfined directions (likely due to creep effects). In the work presented here, PBX 9502 specimens were placed in cup assemblies where they were embedded in Sylgard (an incompressible silicon resin) to provide hydrostatic confinement when the assemblies were placed under different axial loads. The loaded cup assemblies were thermally cycled 10 times to hot and cold temperatures. Finally, results show that increasing the hydrostatic confining pressure causes a decrease in the PBX 9502 volume expansion that occurs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

High Strength and Fracture Resistance of Reduced-Activity W-Ta-Ti-V-Zr High-Entropy Alloy for Fusion Energy Applications

Refractory high-entropy alloys (HEAs) are promising candidates for next-generation nuclear applications, particularly fusion reactors, due to their excellent high-temperature mechanical properties and irradiation resistance. Here, the microstructure and mechanical behavior were investigated for an equimolar WTaTiVZr HEA, designed from a palette of low-activation elements. The as-cast alloy exhibited a dendritic microstructure composed of W-Ta rich dendrites and Zr-Ti-V rich inter-dendritic regions, both possessing a body-centered cubic (BCC) crystal structure. Room temperature bulk compression tests showed ultra-high strength of around 1.6 GPa and plastic strain ~6%, with fracture surfaces showing cleavage facets. The alloy also demonstrated excellent high-temperature strength of ~650 MPa at 500 °C. Scratch-based fracture toughness was ~38 MPa√m for the as-cast WTaTiVZr HEA compared to ~25 MPa√m for commercially used pure tungsten. This higher value of fracture toughness indicates superior damage tolerance relative to commercially used pure tungsten. These results highlight the alloy’s potential as a low-activation structural material for high-temperature plasma-facing components (PFCs) in fusion reactors.

Physics↗
NASA NTRS1974

Optimization of spacecraft high temperature outgassing duration

Spacecraft systems are baked-out under vacuum to remove occluded and adsorbed gases, solvents, water, plasticizer, and other materials acquired during their manufacture. Two bakeouts of solar panels were carried out. Quartz crystal microbalances installed in the vacuum chamber during the tests and held at 273 K (0 C) provided an ongoing measure of the panels' outgassing. From these data, the panels' material weight losses versus time were obtained. A comparison of the total weight loss expected during a relatively long bakeout with that accomplished during a reasonable period of time was used as a criteria for an acceptable duration of the bakeout in order to optimize cost effectiveness.

Scialdone, J. J.↗