SEARCH · Engineering Papers

Results for “performance loss rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Effects of environment on the fatigue of graphite-epoxy composites

Torsional and flexural fatigue tests were performed on both uniaxial (0 deg) and crossplied (plus or minus 45 deg) graphite-epoxy materials at temperatures of 24 and 74 C in environments of air and water. The results of the torsion testing showed that the number of cycles required to cause an initial decrease in stiffness as well as the rate of stiffness loss was a function of temperature and environment; the most significant losses were noted for tests at the higher temperature in water. The torsional fatigue specimens were subsequently tested in four-point bending to determine the effect of torsional damage on longitudinal properties. This damage caused changes in the flexural stiffness, failure stress, and failure energy, depending on the stress and environmental histories. The flexural fatigue tests also showed a significant effect of water (at 24 C) on the material behavior. These results are compared with the results of previous investigations and are discussed in terms of proposed damage mechanisms.

Sumsion, H. T.↗

NASA NTRS1975

Monte Carlo simulation of astronaut light flash observations on Apollo and Skylab missions

Monte Carlo calculations are performed to study the relation between cosmic ray nuclei and visual flashes observed by astronauts, in space. A satisfactory overall fit to all available data excluding the Skylab observations in the South Atlantic Anomaly (SAA) has been achieved by varying three visual system parameters: effective retinal thickness, minimum projected track length inside retina and minimum energy loss rate. All light flash data from space excluding the SAA observations can be understood fully upon the basis of the primary cosmic ray charge and energy spectra together with the fitted values of the three visual system parameters. Monte Carlo simulations of the SAA observations suggest the existence of a previously unobserved multiply-charged component of the inner radiation belt.

Osborne, W. Z.↗

NASA NTRS1987

An evaluation of candidate oxidation resistant materials

Ground based testing of materials considered for Kapton solar array blanket protection, graphite epoxy structural member protection, and high temperature radiators was performed in an RF plasma asher. Ashing rates for Kapton were correlated with rates measured on STS-8 to determine the exposure time equivalent to one year in low Earth orbit (LEO) at a constant density space station orbital flux. Protective coatings on Kapton from Tekmat, Andus Corporation, and LeRC were evaluated in the plasma asher and mass loss rates per unit area were measured for each sample. All samples evaluated provided some protection to the underlying surface but ion beam sputter deposited samples of SiO2 and SiO2 with 8% polytetrafluoroethylene (PTFE) showed no evidence of degradation after 47 hours of exposure. Mica paint was evaluated as a protective coating for graphite epoxy structural members. Mica appears to be resistant to attack by atomic oxygen but only offers some limited protection as a paint because the paint vehicles evaluated to date were not resistant to atomic oxygen. Four materials were selected for evaluation as candidate radiator materials: stainless steel, copper, niobium-1% zirconium, and titanium-6% aluminum-4% vanadium. These materials were surface textured by various means to improve their emittance. Emittances as high as 0.93 at 2.5 microns for stainless steel and 0.89 at 2.5 microns for Nb-1 Zr were obtained from surface texturing. There were no significant changes in emittance after asher exposure.

Rutledge, Sharon↗

NASA NTRSDate not supplied

Computational Assessment of Inlet Backflow Effects on Rotating Detonation Engine Performance and Operability

The performance impact of flow reversal at the inlet of an airbreathing rotating detonation engine (RDE) is investigated using 2 and 3-dimensional computational fluid dynamic (CFD) simulations. Flow reversal, or backflow, occurs in RDE inlets in the high-pressure region directly behind the rotating detonation front. This is also where most of the engine thrust or pressure gain is produced. The amount of backflow relative to throughflow depends on the inlet design. For the present work, a simple annular ‘slit’ design is used. The simulations are idealized in several ways, including that fuel and air are premixed, but prevented from reacting when within the inlet region. The results indicate that even with idealizations, the impact of inlet backflow on pressure gain can be substantial. The simulations also reveal an intriguing instability that develops in certain configurations. The mass flow rate into the RDE begins to oscillate at a regular frequency that is substantially less than the detonation rotational frequency. This is accompanied by oscillations in the detonation height. The oscillation amplitude grows over time until the detonation ultimately fails. Both the performance and instability results emphasize the need for carefully designed RDE inlets that provide low loss when flow is in the forward direction, but high resistance when the flow is reversed. Development of such high-diodicity inlets is critical to achieving pressure gain in airbreathing RDE’s.

Detonation↗

NASA NTRSDate not supplied

Computational Assessment of Inlet Backflow Effects on Rotating Detonation Engine Performance and Operability

detonation↗

DOE OSTI2022

FY22 Progress on Computational Modeling of the Water-Based NSTF

This report summarizes the system-level modeling effort by Argonne National Laboratory (Argonne) of the Natural convection Shutdown heat removal Test Facility (NSTF) in FY22. As an extension of the effort from FY21, this year’s work focuses primarily on the two-phase modeling of the NSTF using RELAP5-3D, particularly with the inclusion of the cavity model. The results from simulations were used to compare against experimental data for benchmarking purposes of the RELAP5 deck. Additionally, RELAP5 was used as a predictive tool to guide planned test operations and identify expected system behaviors. In the first part of this report, details are provided of the cavity omitted model where heat flux is applied directly as a boundary condition to the risers. The general trend predicted by the RELAP5 model matches that from the experimental data when a single-phase natural circulation flow is first established, followed by an oscillatory two-phase period and finally a stable two-phase flow. However, the onset of oscillations is predicted early by the model due to the smaller thermal mixing region in the tank. However, by expanding the simulated thermal mixing region in the tank, the onset of oscillations predicted by the model is able to match that from the experiment. These oscillations where studied in depth and are deduced to be flashing-induced instability. The model was then modified to simulate an accident scenario case where a representative heat load based on the full-scale Framatome’s 625 MW t SC-HTGR was applied directly to the riser channels. The simulated initial and boundary conditions were identical to those performed experimentally, facilitating direct comparisons between the predicted and experimental results. It was determined that the results showed some discrepancies remain, likely due to the overprediction of vapor generation rate by the computer model. In the second part of this report, the cavity model is re-introduced where it is observed that the RELAP5 prediction is now able to capture the major trends of the observed flow commonly observed during two-phase conditions. However, the onset of oscillations is once again predicted early by the model, possibly caused by the underprediction of heat loss from the heater and cavity. This is likely due to the omission of support structures in the cavity that can act as additional pathways for heat to escape to the environment. To overcome the underprediction of heat loss, part of the insulation surrounding the cavity side panels and the back of the heaters are removed to allow heat to escape directly to the environment, which then improves the RELAP5 prediction. Parametric studies are also performed to investigate the effects of heater power, tank inventory level, and tank gas space pressure on flow behaviors, also in direct comparison to conditions tested experimentally. User option-61 in the RELAP5-3D input deck, which changes the heat transfer coefficient correlations used for calculating the vapor generation, is also investigated where it is found that by enabling the option, the overall duration of oscillations is increased and matches that from the experiment better. The RELAP5 model is further benchmarked with a header inlet- throttling case where it is observed that the prediction from the model fails to capture some major features observed in the experiment. By using a modified loss coefficient curve for the valve, the accuracy of the prediction is improved where most of the major features observed in the experiment are predicted by the model. Lastly, the model is benchmarked with an inventory depletion scenario where it is observed that despite the modeling limitation of RELAP5, the prediction shows good agreement with the experimental data where major trends and features are captured by the model. Future work will see continued development of the current RELAP5-3D input deck of the NSTF to both improve the accuracy of the model’s predictive capability and continuing serving the experimental program. The mutually beneficial relationship between analysis and experimental efforts has become integral to the parent NSTF program, and the greater objective to fully understand and accurately predict the heat removal performance of a full scale RCCS concept.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1979

User's manual for PRESTO: A computer code for the performance of regenerative steam turbine cycles

Standard turbine cycles for baseload power plants and cycles with such additional features as process steam extraction and induction and feedwater heating by external heat sources may be modeled. Peaking and high back pressure cycles are also included. The code's methodology is to use the expansion line efficiencies, exhaust loss, leakages, mechanical losses, and generator losses to calculate the heat rate and generator output. A general description of the code is given as well as the instructions for input data preparation. Appended are two complete example cases.

Fuller, L. C.↗

DOE OSTI2024

CMPLE: Correlation Modeling to Decode Photosynthesis Using the Minorize–Maximize Algorithm

In plant genomic experiments, correlations among various biological traits (phenotypes) give new insights into how genetic diversity may have tuned biological processes to enhance fitness under diverse conditions. Consequently, knowing how the correlations are affected by genetic (G) and environmental (E) factors helps develop climate-resilient plants. However, the current literature lacks any method for assessing the effect of predictors on pairwise correlations among multiple phenotypes together with easily interpretable model parameters. To address this need, we propose to model pairwise correlations directly in terms of G and E and develop a computationally efficient inference procedure. Two major novelties in our methodology are (1) the use of a composite pairwise likelihood method to avoid the positive definiteness restriction on the correlation matrix and (2) the use of a novel Minorize–Maximize (MM) algorithm for the efficient estimation of a large number of parameters. The proposed method shows excellent numerical performance on synthetic datasets. Here, the analysis of the motivating data on cowpea reveals that the rates of solar energy storage by photosynthesis (the aggregate trait) are differentially affected by different genetic loci through two distinct processes: “photoinhibition” which results from photodamage caused by excess light, and “photoprotection” which protects plants from photodamage but also results in energy loss.

Correlation modeling↗

DOE OSTI2020

Benchmark Simulation of the Natural Convection Shutdown Heat Removal Test Facility Using SAM

Natural convection systems are a promising method to passively remove heat from reactor cavities during loss of forced flow accident scenarios. In this work at Argonne National Laboratory (ANL), a highly instrumented Natural Convection Shutdown Heat Removal Test Facility (NSTF) was used to demonstrate the effectiveness of air-cooled natural convection systems. In previous work, RELAP5-3D simulations were performed on this facility with favorable comparisons to experiment for mass flow rate, pressure drop, air temperature increase, and air velocity. Both experimental and simulation efforts with this facility present a useful opportunity to perform a benchmark study with the System Analysis Module (SAM). SAM is an advanced thermal-hydraulic system code currently in development at ANL for advanced non-light water reactor safety analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Testing the LSST Difference Image Analysis Pipeline Using Synthetic Source Injection Analysis

Abstract We evaluate the performance of the Legacy Survey of Space and Time Science Pipelines Difference Image Analysis (DIA) on simulated images. By adding synthetic sources to galaxies on images, we trace the recovery of injected synthetic sources to evaluate the pipeline on images from the Dark Energy Science Collaboration Data Challenge 2. The pipeline performs well, with efficiency and flux accuracy consistent with the signal-to-noise ratio of the input images. We explore different spatial degrees of freedom for the Alard–Lupton polynomial-Gaussian image subtraction kernel and analyze for trade-offs in efficiency versus artifact rate. Increasing the kernel spatial degrees of freedom reduces the artifact rate without loss of efficiency. The flux measurements with different kernel spatial degrees of freedom are consistent. We also here provide a set of DIA flags that substantially filter out artifacts from the DIA source table. We explore the morphology and possible origins of the observed remaining subtraction artifacts and suggest that given the complexity of these artifact origins, a convolution kernel with a set of flexible bases with spatial variation may be needed to yield further improvements.

Liu, S. (ORCID:0000000244612143)↗

NASA NTRS1983

Development of a distributed-parameter mathematical model for simulation of cryogenic wind tunnels

A one-dimensional distributed-parameter dynamic model of a cryogenic wind tunnel was developed which accounts for internal and external heat transfer, viscous momentum losses, and slotted-test-section dynamics. Boundary conditions imposed by liquid-nitrogen injection, gas venting, and the tunnel fan were included. A time-dependent numerical solution to the resultant set of partial differential equations was obtained on a CDC CYBER 203 vector-processing digital computer at a usable computational rate. Preliminary computational studies were performed by using parameters of the Langley 0.3-Meter Transonic Cryogenic Tunnel. Studies were performed by using parameters from the National Transonic Facility (NTF). The NTF wind-tunnel model was used in the design of control loops for Mach number, total temperature, and total pressure and for determining interactions between the control loops. It was employed in the application of optimal linear-regulator theory and eigenvalue-placement techniques to develop Mach number control laws.

Tripp, J. S.↗

NASA NTRS1989

The use of interleaving for reducing radio loss in convolutionally coded systems

The use of interleaving after convolutional coding and deinterleaving before Viterbi decoding is proposed. This effectively reduces radio loss at low-loop Signal to Noise Ratios (SNRs) by several decibels and at high-loop SNRs by a few tenths of a decibel. Performance of the coded system can further be enhanced if the modulation index is optimized for this system. This will correspond to a reduction of bit SNR at a certain bit error rate for the overall system. The introduction of interleaving/deinterleaving into communication systems designed for future deep space missions does not substantially complicate their hardware design or increase their system cost.

Divsalar, D.↗

NASA NTRS2011

Thermal Protection System Aerothermal Screening Tests in HYMETS Facility

The Entry, Descent, and Landing (EDL) Technology Development Project has been tasked to develop Thermal Protection System (TPS) materials for insertion into future Mars Entry Systems. A screening arc jet test of seven rigid ablative TPS material candidates was performed in the Hypersonic Materials Environmental Test System (HYMETS) facility at NASA Langley Research Center, in both an air and carbon dioxide test environment. Recession, mass loss, surface temperature, and backface thermal response were measured for each test specimen. All material candidates survived the Mars aerocapture relevant heating condition, and some materials showed a clear increase in recession rate in the carbon dioxide test environment. These test results supported subsequent down-selection of the most promising material candidates for further development.

thermal protection systems (TPS)↗

DOE OSTI2025

Computer-Based Procedures Among Older Adults: Findings from the Rancor Microworld Simulator

As with many industries worldwide, nuclear energy is experiencing an aging workforce; older than other energy sources and the national average. For example, while almost one in three nuclear industry professionals are 55+ years, for oil and gas that number is one in five. The challenges brought about by an aging workforce are one of the industry’s top concerns. However, the industry lacks for empirical research that examines the effects of developmental aging in older workers, as well as the interactions between aging and new digital technologies. We present the results of an experiment that tested three different computer-based procedures in a sample of 30 older adults (55+ years). While the industry has traditionally relied on paper-based procedures, these are being modernized by digital technology. Participants were randomly assigned to one of three procedure-types that varied by the level of digitalization, based on the IEEE Standard-1786. Type 1 essentially represents a digital representation of a paper-based procedure, Type 2 adds embedded indicators, and Type 3 adds soft controls. Participants performed two different operational scenarios (startup and loss of feedwater) on a simplified nuclear power plant simulator. Results revealed a weak signal that Type 2 may produce lower workload and lower completion times in some instances. However, there were no significant effects of procedure-type across any other outcomes, including simulator log data, situation awareness, and preference ratings. We discuss our findings in terms of optimal levels of digitalization/automation for an aging nuclear workforce and suggest pathways for future directions.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗

DOE OSTI2021

Fitness cost of vancomycin-resistant Enterococcus faecium plasmids associated with hospital infection outbreaks

Abstract Background Vancomycin resistance is mostly associated with Enterococcus faecium due to Tn1546-vanA located on narrow- and broad-host plasmids of various families. This study’s aim was to analyse the effects of acquiring Tn1546-carrying plasmids with proven epidemicity in different bacterial host backgrounds. Methods Widespread Tn1546-carrying plasmids of different families RepA_N (n = 5), Inc18 (n = 4) and/or pHTβ (n = 1), and prototype plasmids RepA_N (pRUM) and Inc18 (pRE25, pIP501) were analysed. Plasmid transferability and fitness cost were assessed using E. faecium (GE1, 64/3) and Enterococcus faecalis (JH2-2/FA202/UV202) recipient strains. Growth curves (Bioscreen C) and Relative Growth Rates were obtained in the presence/absence of vancomycin. Plasmid stability was analysed (300 generations). WGS (Illumina-MiSeq) of non-evolved and evolved strains (GE1/64/3 transconjugants, n = 49) was performed. SNP calling (Breseq software) of non-evolved strains was used for comparison. Results All plasmids were successfully transferred to different E. faecium clonal backgrounds. Most Tn1546-carrying plasmids and Inc18 and RepA_N prototypes reduced host fitness (–2% to 18%) while the cost of Tn1546 expression varied according to the Tn1546-variant and the recipient strain (9%–49%). Stability of Tn1546-carrying plasmids was documented in all cases, often with loss of phenotypic resistance and/or partial plasmid deletions. SNPs and/or indels associated with essential bacterial functions were observed on the chromosome of evolved strains, some of them linked to increased fitness. Conclusions The stability of E. faecium Tn1546-carrying plasmids in the absence of selective pressure and the high intra-species conjugation rates might explain the persistence of vancomycin resistance in E. faecium populations despite the significant burden they might impose on bacterial host strains.

Tedim, Ana P.↗

DOE OSTI2023

Developing a microwave-driven reactor for ammonia synthesis: insights into the unique challenges of microwave catalysis

Rapid development of new ammonia (NH 3 ) synthesis techniques that enable modular, intermittent production is essential to actualizing NH 3 's potential as a clean energy carrier, since contemporary methods are configured to centralized, continuous production methods with high emissions and are incompatible with renewable sources. Here, in this mission, microwave-driven catalysis is promising for its ability to enhance reaction kinetics and apply targeted heating for efficient energy use. However, owing to an incomplete understanding of the interaction between microwave fields and catalyst beds, the development of such microwave-catalysis systems remains underexplored and challenging. This paper investigates the 10× scale-up of a microwave-based NH 3 synthesis reactor using numerical and experimental approaches, achieving the largest reported microwave-driven NH 3 reactor to date. Results elucidate phenomena unique to microwave processes that are only predictable through numerical modeling, including how a catalyst's dielectric properties influence microwave field distribution by affecting penetration depth and how energy utilization can be poor even with sufficient attenuation. These dynamics change with scale, constrain reactor geometry, and potentially hamper performance. Nonetheless, we demonstrate a production rate of 56.6 g NH$_3$ per day, the highest reported NH 3 synthesis rate for laboratory-scale alternative techniques; correspondingly, the benchmark energy efficiency achieved in this paper (45.6 g NH$_3$ kW h -1 ) is the highest reported for such reactors of sufficient scale. Even with this exemplary energy efficiency, energy losses were found in excess of 50%, an issue resolvable through scale and reactor design. The efficiencies imparted by microwaves were key in these achievements, warranting further investigation toward development of microwave-driven NH 3 systems.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1976

Effect of thermal cycling in a Mach 0.3 burner rig on properties and structure of directionally solidified gamma/gamma prime-delta eutectic

An experimental study was carried out to evaluate the effect of cyclic thermal exposures on the mechanical properties of a gamma/gamma prime-delta eutectic alloy parallel to the growth direction. The alloy had a nominal composition by weight of Ni-20 Nb-6 Cr-2.5 Al and was directionally solidified at 3 cm/hr in a furnace with a thermal gradient of at least 200 C/cm. Bars of the alloy were exposed in a Mach 0.3 burner rig and cycled 300 times between 1100 and 425 C. Oxidation-erosion characteristics of the alloy were determined by weight loss measurements at 300-cycle intervals. After cyclic exposure, stress rupture and tensile tests were performed at both 760 and 1040 C. Microstructural changes from cyclic exposure were determined. Thermal cycling resulted in gamma prime coarsening and Widmanstaetten delta precipitation in the gamma phase. An unidentified precipitate, presumably gamma prime, was observed within the delta phase. These microstructural changes did not affect the mechanical properties of the eutectic. High oxidation-erosion weight loss rate was observed.

Gray, H. R.↗

NASA NTRS2016

ACES M and S: Unmitigated Factorial Encounter Study on DAA/TCAS Interoperability

Realization of the expected proliferation of Unmanned Aircraft System (UAS) operations in the National Airspace System (NAS) depends on the development and validation of standards for UAS Detect and Avoid (DAA) Systems. The RTCA Special Committee 228 is charged with leading the development of draft Minimum Operational Performance Standards (MOPS) for UAS DAA Systems. NASA, as a participating member of RTCA SC-228 is committed to supporting the development and validation of draft requirements for DAA alerting and guidance systems. This presentation contains the results of two combinatorial encounter analysis studies using NASA's SAA Control fast-time simulation capability for this purpose. In these studies, encounters between two aircraft were simulated one at a time for the full factorial combination of encounter geometries (e.g., encounter angle, CPA offset) and aircraft performance (e.g., ownership and intruder ground speeds and vertical rates). The first study analyzes the relationships (e.g., timeline) between the different alerting-safety regions in the SC-228 MOPS (in order of increasing severity): 1) DAA warning alert, 2) well clear recovery (WCR) guidance, 3) DAA-Collision Avoidance (CA), and 4) TCAS RA. This study will focus primarily on encounter situations in which TCAS RA occurs prior to any of the other alerting-safety boundaries. In particular, this study will investigate whether using vertical distance or vertical distance at closest point of approach (i.e., vertical miss distance or VMD) is more appropriate for the definition of the DAA-CA region. In addition, cases where transitions between different regions skip an intermediate region will be analyzed. The second study in this presentation explores a proposal to use an altitude rate error threshold to determine if vertical maneuvers are acceptable for DAA WCR guidance against non-cooperative intruders. This study incorporates the radar from the Honeywell sensor model and examines a series of pairwise encounters between a non-cooperative intruder and a UAS ownship, with different combinations of intruder states and ownship performance levels. The study uses SAA Control as a simulation platform and pilot model, and Omnibands to provide DWC recovery guidance. Two simulation sets, one that allows vertical DWC recovery guidance and one that does not, are compared to determine if encounters with altitude rate errors above 250 feet-per-minute are more likely to have more severe losses of well clear, as determined by the Loss of Well-Clear Severity metric.

SaaControl↗