Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “paints”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Forward Skirt Structural Testing on the Space Launch System (SLS) Program

Structural testing was performed to evaluate heritage forward skirts from the Space Shuttle program for use on the Space Launch System (SLS) program. One forward skirt is located in each solid rocket booster. Heritage forward skirts are aluminum 2219 welded structures. Loads are applied at the forward skirt thrust post and ball assembly. Testing was needed because SLS ascent loads are roughly 40% higher than Space Shuttle loads. Testing objectives were to determine margins of safety, demonstrate reliability, and validate analytical models. Two forward skirts were structurally tested using the test configuration. The test stand applied loads to the thrust post. Four hydraulic actuators were used to apply axial load and two hydraulic actuators were used to apply radial and tangential loads. The first test was referred to as FSTA-1 (Forward Skirt Structural Test Article) and was performed in April/May 2014. The purpose of FSTA-1 was to verify the ultimate capability of the forward skirt subjected to ascent ultimate loads. Testing consisted of two liftoff load cases taken to 100% limit load followed by an ascent load case taken to 110% limit load. The forward skirt was unloaded to no load after each test case. Lastly, the forward skirt was tested to 140% limit and then to failure using the ascent loads. The second test was referred to as FSTA-2 and performed in July/August of 2014. The purpose of FSTA-2 was to verify the ultimate capability of the forward skirt subjected to liftoff ultimate loads. Testing consisted of six liftoff load cases taken to 100% limit load followed by the six liftoff cases taken to 140% limit load. Two ascent load cases were then tested to 100% limit load. The forward skirt was unloaded to no load after each test case. Lastly, the forward skirt was tested to 140% limit and then to failure using the ascent loads. The forward skirts on FSTA-1 and FSTA-2 successfully carried all applied liftoff and ascent load cases. Both FSTA-1 and FSTA-2 were tested to failure by increasing the ascent loads. Failure occurred in the forward skirt thrust post radius. The forward skirts on FSTA-1 and FSTA-2 had nearly identical failure modes. FSTA-1 failed at 1.72 times limit load and FSTA-2 failed at 1.62 times limit load. This difference is primarily attributed to variation in material properties in the thrust post region. Test data were obtained from strain gages, deflection gages, ARAMIS digital strain measurement, acoustic emissions, and high-speed video. Strain gage data and ARAMIS strain were compared to finite element (FE) analysis predictions. Both the forward skirt and tooling were modeled. This allows the analysis to simulate the loading as close as possible to actual test configuration. FSTA-1 and FSTA-2 were instrumented with over 200 strain gages to ensure all possible failure modes could be captured. However, it turned out that three gages provided critical strain data. One was located in the post bore and two on the post radius. More gages were not specified due to space limitations and the desire to not interfere with the use of the ARAMIS system on the post radius. Measured strains were compared to analysis results for the load cycle to failure. Note that FSTA-1 gages were lost before failure was reached. FSTA-2 gages made it to the failure load but one of the radius gages was lost before testing began. This gage was not replaced because of the time and cost associated with disassembly of the test structure. Correlation to analysis was excellent for FSTA-1. FSTA-2 was not quite as good because there was more residual strain from previous load cycles. FSTA-2 was loaded and unloaded with 12 liftoff cases and two ascent cases before taking the skirt to failure. FSTA-1 only had two liftoff cases and one ascent case before taking the skirt to failure. The ARAMIS system was used to determine strain at the post radius by processing digital images of a speckled paint pattern. Digital cameras recorded images of the speckled paint pattern. ARAMIS strain results for FSTA-2 just prior to failure. Note a high strain location develops near the left side. This high strain compares well to analysis prediction for both FSTA-1 and FSTA-2. The strain at this location was also plotted versus limit load. Both FSTA-1 and FSTA-2 had excellent correlation between ARAMIS and analysis strains. Acoustic emission (AE) sensors were used to monitor for damage formation that may occur during testing (e.g., crack formation and growth or propagation). AE was very important because after disassembly of FSTA-1, a crack was observed in the ball fitting radius. The ball fitting did not crack on FSTA-2. AE data was used to reconstruct when the crack occurred. The AE energy versus time plot for FSTA. The energy increased considerably at 850 seconds (152% limit load), indicating a crack could have formed at this point. The only visual evidence found that could have corresponded to this was the crack that initiated in the ball fitting. The cracks in the forward skirt aluminum structures would likely have been lower energy due to a lower modulus and all that were found after failure correlated to occurring after the initial crack in the post radius. This was verified by high-speed cameras used to record the failure.

Lohrer, J. D.↗
NASA NTRS2017

Application of Molecular Adsorber Coatings in Chamber A for the James Webb Space Telescope

As a coating made of highly porous zeolite materials, the Molecular Adsorber Coating (MAC) was developed to capture outgassed molecular contaminants, such as hydrocarbons and silicones. For spaceflight applications, the adsorptive capabilities of the coating can alleviate on-orbit outgassing concerns on or near sensitive surfaces and instruments within the spacecraft. Similarly, this sprayable paint technology has proven to be significantly beneficial for ground-based space applications, in particular, for vacuum chamber environments. This presentation describes the application of the MAC technology for the James Webb Space Telescope (JWST) at NASA Johnson Space Center (JSC). The coating was used as a mitigation tool to entrap outgassed contaminants, specifically silicone-based diffusion pump oil, from within JSCs cryogenic optical vacuum chamber test facility called Chamber A. This presentation summarizes the background, fabrication, installation, chemical analysis test results, and future plans for the MAC technology, which was effectively used to protect the JWST test equipment from vacuum chamber contamination. As a coating made of highly porous zeolite materials, the Molecular Adsorber Coating (MAC) was developed to capture outgassed molecular contaminants, such as hydrocarbons and silicones. For spaceflight applications, the adsorptive capabilities of the coating can alleviate on-orbit outgassing concerns on or near sensitive surfaces and instruments within the spacecraft. Similarly, this sprayable paint technology has proven to be significantly beneficial for ground-based space applications, in particular, for vacuum chamber environments. This presentation describes the application of the MAC technology for the James Webb Space Telescope (JWST) at NASA Johnson Space Center (JSC). The coating was used as a mitigation tool to entrap outgassed contaminants, specifically silicone-based diffusion pump oil, from within JSCs cryogenic optical vacuum chamber test facility called Chamber A. This presentation summarizes the background, fabrication, installation, chemical analysis test results, and future plans for the MAC technology, which was effectively used to protect the JWST test equipment from vacuum chamber contamination.

molecular contamination↗
NASA NTRS2016

Cryogenic Selective Surfaces

There are many challenges involved in deep-space exploration, but several of these can be mitigated, or even solved, by the development of a coating that can reject most of the Sun's energy and yet still provide some far-infrared heat emission. Such a coating would allow non-heat-generating objects in space to reach cryogenic temperatures without using an active cooling system. This would be a benefit to deep-space sensors that require low temperatures, such as the James Webb Telescope focal plane array. It would also allow the use of superconductors in deep space, which could lead to magnetic energy storage rings, lossless power delivery, or perhaps a large-volume magnetic shield against galactic cosmic radiation. But perhaps the most significant enablement achieved from such a coating would be the long-term storage in deep space of cryogenic liquids, such as liquid oxygen (LOX).In this report, we review the state of the art in low-temperature coatings and calculate the lowest temperatures each of these can achieve, demonstrating that cryogenic temperatures cannot be reached in deep space in this fashion. We then propose a new coating that does allow coated objects in deep space to achieve the very low temperatures required to store liquid oxygen or nitrogen. These new coatings consist of a moderately thick scattering layer (typically 5 mm) composed of a material transparent to most of the solar spectrum. This layer acts as a scatterer to the Sun's light, performing the same process as titanium dioxide in white paint in the visible. Under that layer, we place a metallic reflector, e.g. silver, to reflect long-wave radiation that is not well scattered. The result is a coating we call "Solar White," in that it scatters most of the solar spectrum just as white paint does for the visible. Our modeling of these coatings has shown that temperatures as low as 50 K can be reached for a coated object fully exposed to sunlight at 1 AU from the Sun and far from the Earth.In the second half of the report we explore a mission application of this coating in order to show that it allows LOX to be carried on a mission to Mars. Heat can reach a LOX tank in five ways: direct radiation from the Sun, scattered or reflected radiation from the Sun off of spacecraft components, radiation from nearby planets or the Moon, radiation from the infrared emission of other parts of the spacecraft, and conduction along support struts and flow lines. We discuss these and sum their total contribution when using a Solar White coating to demonstrate an architecture that allows the transportation of LOX to Mars. After this, other applications of Solar White are listed.

Cryogenic Materials↗
NASA NTRS2019

Wind Tunnel Flow Field Visualizations of the Space Launch System Vehicle Ascent

A series of wind tunnel tests were conducted to characterize the force-and-moment, and aeroacoustic environment of several configurations of the Space Launch System during ascent. The tests were conducted in the 11-by-11 foot transonic and 9-by-7 foot supersonic test sections at NASA Ames research center. Throughout these experiments data was collected from several types of instrumentation including: multicomponent force-and-moment strain gage balances, dynamic and steady-state pressure sensors, unsteady and steady pressure-sensitive paint, time-resolved shadowgraph and infrared imaging. The following details results and analysis from the time-resolved shadowgraph and infrared imaging data systems. The time-resolved shadowgraph and infrared imaging provided a qualitative measurement of the near-field turbulent fluctuations. These results helped provide context to the relative magnitude and frequency content of the fluid-structure-interaction driving the surface pressure phenomena characterized by the discrete pressure transducers and unsteady pressure sensitive paint.

Garbeff, Theodore J., II↗
NASA NTRS2019

NIAC Phase I Final Report: On-Orbit, Collision-Free Mapping of Small Orbital Debris

Sub-centimeter orbital debris is currently undetectable using ground-based radar and optical methods. However, the pits in Space Shuttle windows produced by paint chips (e.g. the 3.8mm diameter pit produced by a 0.2mm paint chip on STS-7) demonstrate that small debris can cause serious damage to spacecraft. Recent analytical, computational and experimental work has shown that charged objects moving quickly through a plasma will cause the formation of solitons in the plasma density. Due to their exposure to the solar wind plasma environment, even the smallest space debris will be charged. Depending on the debris size, charge and velocity, the plasma signature of the solitons may be detected by simple instrumentation on spacecraft. We will describe the amplitude and velocity of solitons that may be produced by mm-cm scale orbital debris in LEO. We will discuss the feasibility of mapping sub-cm orbital debris using a fleet of CubeSats equipped with Langmuir probes. The time and fleet size required to map the debris will also be described. Plasma soliton detection would be the first collision-free method of mapping the small debris population.

Orbital Debris↗
NASA NTRS2019

Space Launch System Booster Separation Supersonic Powered Testing with Surface and Off-Body Measurements

A wind tunnel test was run in the NASA Langley Unitary Plan Wind Tunnel simulating the separation of the two solid rocket boosters (SRB) from the core stage of the NASA Space Launch System (SLS). The test was run on a 0.9% scale model of the SLS Block 1B Cargo (27005) configuration and the SLS Block 1B Crew (28005) configuration at a Mach of 4.0. High pressure air was used to simulate plumes from the booster separation motors located at the nose and aft skirt of the two boosters. Force and moment data were taken on both SRBs and on the core stage. Schlieren still photos and video were recorded throughout testing. A set of points were acquired using Cross-correlation Doppler Global Velocimetry (CCDGV) readings to get 3 component velocity measurements between the core and the left-hand SRB. The CCDGV laser was utilized to record flow visualization in the same location, between the core and the left-hand SRB. Pressure Sensitive Paint data were taken on a separate set of runs. Computational Fluid Dynamics (CFD) runs were computed on a subset of the wind tunnel data points for comparison. A combination of the force/moment, CCDGV and Pressure Sensitive Paint (PSP) data (as well as schlieren images) at the CFD-specified test conditions will be used te the CFD simulations that will be used to build an SLS booster separation database flight conditions.

Winski, Courtney S.↗
NASA NTRSDate not supplied

Testing of Mars Retropropulsion Concepts in the Langley Unitary Plan Wind Tunnel

Future Mars human lander missions will require using retrorockets beginning at supersonic conditions, something which has never been done before at Mars. Significant aerosciences challenges exist due to interactions between the retrorocket exhaust plumes, the freestream flow, and the vehicle that alter the aerodynamic behavior. Historical retropropulsion ground and flight data do not provide a basis for calibrating the computational uncertainties for aerodynamic interference forces and moments on proposed Mars descent vehicles, either because of insufficient data or dissimilar vehicles geometries and/or conditions. A new retropropulsion wind tunnel test was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to address some of the deficiencies of previous tests and to provide a basis for computational model comparisons on relevant geometries. The test included improvements in model design and measured data. Two sub-scale model geometries derived from full-scale vehicle concepts were tested: a blunt low lift-to-drag vehicle and a more slender geometry. The first model includes variations in nozzle parameters that were estimated to have first-order effects on the measurements: location, pointing direction, size, and exit-to-throat area ratio. Both models were instrumented with discrete steady and unsteady pressure sensors on the aerodynamic and interior flow path surfaces. The heats shields of both models also were covered with pressure sensitive paint that effectively measures a steady pressure distribution in an otherwise unsteady flow field. This pressure distribution was integrated over the surface geometry in order to estimate the steady aerodynamic force and moment coefficient contribution from the painted surfaces; this approach was used as a replacement for using a flow-through balance. This paper will cover the test objectives, model design, test matrix, and available test results for each model configuration at different freestream Mach numbers, model attitude, and non-dimensional thrust magnitude. A subsequent publication will cover uncertainty quantification of the test data and comparisons to computational fluid dynamics model results.

Powered Descent↗
NASA NTRSDate not supplied

Visualizing UPSP Data with Python

The Unsteady Pressure-Sensitive Paint (uPSP) projects uses Pressure-Sensitive paint applied over aerospace models during wind tunnel testing to collect pressure data with high spatial and temporal resolution in order to inform unsteady aerodynamics studies. For each of the 800+ experimental runs, four cameras generate up to 50 GB of video data, which must then be processed, analyzed, and visualized on the NASA Advanced Supercomputing system (NAS) to assess the result. One of the final data analysis products is the dynamic modal decomposition (DMD) results, which decomposes the pressure reading signals by their frequency component. The goal of this project is to visualize the DMD results over a 3D rendering of the model, using efficient and parallelized python routines. The software uses the pytecplot library, a high-level API that connects python scripting to a Tecplot 360 engine. Tecplot is an industry standard high-performance visualization tool that can handle large datasets and workflow. Various animation, rendering, and image-combination techniques were investigated to generate the final videos using OpenCV on the NAS. The final result is a software tool that takes in data products from the uPSP processing chain and generates high resolution visualization videos in parallel for every data file, allowing researchers to view their results efficiently and at an unprecedentedly detailed level.

Emma Dolores McMillian↗
NASA NTRS2021

Pedestal Hazard Abatement and Soil Removal Construction Completion Report for Launch Complex 34, Solid Waste Management Unit CC054, Cape Canaveral Space Force Station, Florida

This Construction Completion Report summarizes the activities associated with implementation of an interim measure (IM) for hazard abatement of the Launch Pedestal and soil removal at Launch Complex 34 (LC34), Cape Canaveral Space Force Station, Florida. The purpose of the hazard abatement IM was to mitigate any continuing source of contamination associated with residual paint on the Launch Pedestal that contained polychlorinated biphenyls (PCBs). Sampling determined that residual PCB concerns were limited to the steel elements on the top-side of the Pedestal, which included the torus ring, feed pipe, down pipes, pipe straps and shields, remaining steel cover plates and bolts, and railing support steel. The IM also mitigated the potential spread of contamination to surrounding areas by removing fallen metal fragments from the concrete launch pad, as well as soil from trenches on the launch pad where PCB-containing paint chips may have accumulated prior to or during Pedestal hazard abatement activities.

Complex 34↗
NASA NTRSDate not supplied

Unsteady PSP in the NASA Transonic Dynamics Tunnel

For the first time, unsteady pressure sensitive paint (uPSP) has been applied in the NASA Langley Transonic Dynamics Tunnel. Obtaining global surface pressure measurements using the uPSP technique required the development of a new paint formulation for use in the low oxygen heavy gas atmosphere, as well as environmental enclosures to protect sensitive electro-optical components from the high temperature, low pressure environment present during tunnel operation. A high-speed datalink connecting the wind tunnel to Langley’s local high performance compute resource was also established for this test to enable near real time processing of the large datasets that were obtained throughout the campaign. A high-speed lifetime measurement technique was also utilized to yield steady state surface pressures at each condition using the same equipment that was used to provide unsteady measurements. Important metrics such as pressure time histories and power spectral density are compared against traditional unsteady pressure point measurements, and more advanced data products such as dynamic mode decomposition are also explored to provide insight into the underlying flow phenomena.

Daniel T. Reese↗
DOE OSTI2022

Pattern bonded finned cold plate

An apparatus includes a fin pack of parallel plates that protrude from a base, a lid attachable to the fin pack opposite the base, and a brazing material painted onto the lid only in a plurality of wettable regions. The lid is positioned against the fin pack, opposite the base, with portions of the plurality of regions contacting edges of the parallel plates. The lid is brazed to the fin pack without intrusion of the brazing material between the parallel plates. This is accomplished by obtaining a lid to be attached to a fin pack of parallel plates that protrude from a base, painting the lid with the brazing material only in a plurality of wettable regions, positioning the lid against the fin pack, opposite the base, with portions of the plurality of regions contacting edges of the parallel plates, and brazing the lid to the fin pack.

Schultz, Mark D.↗
NASA NTRSDate not supplied

Polymeric Materials Application and Testing for Space Missions

The EM41 Non-metallics polymers team performs polymeric materials screening, characterization, development, qualification, verification and validation testing for flight hardware and in-space applications. They perform insight, testing and application of polymeric materials for launch vehicles and space environments. Personnel have a deep understanding of the technologies associated with cryogenic insulation, high temperature thermal protection materials, paints, primers, coatings, and adhesive materials. Numerous TPS material characterization tests can also be performed by the Lab. The team has both internal and partner test capabilities to subject polymeric materials to Aerospace and Space environments Material properties, response and performance are tested within environments from the launch pad, through the launch environment and into space. A primary role of the team is to select materials and organize test regimen then analyze test results. Test regiment are established to confirm the materials meet the performance requirements levied by customers within the environments that are expected for the mission.

Thermal↗
DOE OSTI2023

Room Temperature Stamping of High-Strength Aluminum for Lightweight Structural Automotive Components

The use of aluminum (Al) 7xxx series in automobile structural applications is limited by factors such as its low room-temperature formability in T6 temper and the need for off-line artificial aging to regain high strength if it is formed in soft temper. In this study, two tempers were established that enable Al 7075 blanks to be room temperature stamped to create side impact beams that achieve near-T6 strength without post-forming artificial aging. It is shown that natural aging at room temperature, after solution treatment and before stamping, provides an alternative to high temperature pre-aging and hot stamping techniques in 7xxx alloys. Both tempers enabled room temperature stamping of the beams without cracking, indicating good formability. The Al beams were ~38% lighter than the benchmark boron steel beam. Further, the hardness in the low-deformation regions of the stamped Al beams were within 88% of a conventional 7075-T6 sheet. Paint-bake treatment of the beams appeared to cause over aging, lowering the ultimate tensile strength and ductility. Finite element three point bending simulations of the beams showed higher bending force and energy absorption before failure for the Al 7075 showing good promise for 7xxx series Al as a light-weight alternative to steel beams.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Surface Properties of Double-Fin Generated Shock-Wave/Boundary-Layer Interactions

Shock-Wave/Boundary-Layer Interaction (SBLI) is ubiquitous in high-speed air vehicles. SBLI surface flowfield properties of crossing shocks induced by symmetric Double-Fins (DFs) at fin angles of 8° and 10° at Mach 2 are experimentally investigated; a 10° Single-Fin (SF) is also explored as a comparison. Surface visualization is used to capture distinct flowfield structures such as separation and upstream influence. Steady and unsteady Pressure-Sensitive Paints (PSPs) are used to obtain global surface pressure fields. Characteristics of DF-SBLI surface topology are discussed by comparing the corresponding SF-SBLI. Here, the effect of fin angle on DF-SBLI is characterized, and unsteady dynamics of the pressure field are examined. Spectral Proper Orthogonal Decomposition (SPOD) is performed on unsteady PSP, and traveling surface pressure waves and their frequency-dependent behavior are discussed. Dispersion relation of surface pressure waves is revealed by performing two-dimensional space–time Fourier transform on unsteady PSP, and the results are compared with the phase velocity distributions obtained from SPOD. Accompanying group velocity behavior is examined for distinct SBLI regions wherein wave propagation is found dependent on its frequency. Steady surface pressures along the centerline are compared with previous experimental data. Fin-tip spacing is found to be an essential parameter for scaling of upstream influence length.

33 ADVANCED PROPULSION SYSTEMS↗