SEARCH · Engineering Papers

Results for “model scaling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Engineering-scale Modeling of High-Temperature Creep and Creep Crack Growth in Alloy 316H

This document demonstrates completion of the goals described in the technical narrative of the Department of Energy’s Industry Funding Opportunity Announcement (iFOA) project entitled “Modeling and Simulation Development Pathways to Accelerating KP-FHR Licensing,” which relates to the development and demonstration of capabilities for conducting engineering-scale simulations of Alloy 316H components under high-temperature conditions. This work encompassed two major aspects: integrating and testing constitutive models for the creep response of 316H at high temperatures, and developing tools for modeling creep crack growth (CCG) in 316H. Two classes of constitutive models were used in this effort: phenomenological models based on behavior observed at the engineering scale, and reduced-order models (ROMs) that represent the nonlinear response of mesoscale models that capture the sensitivity to material microstructure and processing. Likewise, the approaches employed for CCG modeling considered both simplified engineering approaches and detailed simulations of creep and damage ahead of the crack tip. These developments, which were performed by utilizing the Grizzly code as well as the open-source libraries it depends on, strengthen Grizzly’s ability to support licensing and safety analyses of high-temperature reactor components.

316H↗

NASA NTRS1972

Heat transfer and pressure distributions at M equals 8 on 0.029 scale models of the Viking entry vehicle

An investigation in the Langley Research Center Mach-8 Variable Density Hypersonic Tunnel was made of the pressure distributions and heat transfer rate distributions on two 0.029 scale Viking Entry Vehicle models. Comparable ranges of test Reynolds number were exercised for the two tests between run conditions around 4 million and conditions of about 1.6 million. At angles of attack less than 20 degrees the pressure ratio distribution referenced to stagnation pressure appeared invariant with Reynolds number. Increasing angle of attack results in a flatter distribution of both the windward and leeward pressure distributions; in addition, the stagnation point shifted into the windward plane. A subsequent rise in the heating rate profile on the leeward side with further increase in angle of attack is attributed to boundary layer natural transition to turbulent flow. Schlieren photographs were taken for flow field visualization and to correct model angle of attack.

Faye-Petersen, R.↗

NASA NTRS1979

Evaluation of subgrid-scale models using an accurately simulated turbulent flow

A calculation of periodic homogeneous isotropic turbulence is used to simulate the experimental decay of grid turbulence. The calculation is found to match the experiment in a number of important aspects and the computed flow field is then treated as a realization of a physical turbulent flow. From this flow, a calculation is conducted of the large eddy field and the various averages of the subgrid-scale turbulence that occur in the large eddy simulation equations. These quantities are compared with the predictions of the models that are usually applied in large eddy simulation. The results show that the terms which involve the large-scale field are accurately modeled but the subgrid-scale Reynolds stresses are only moderately well modeled. It is also possible to use the method to predict the constants of the models without reference to experiment. Attempts to find improved models have not met with success.

Clark, R. A.↗

NASA NTRS1975

Results of aerodynamic heat transfer tests of a 0.0175-scale model of the Rockwell International Space Shuttle Orbiter 139 (model number 22-0) in the NASA/Ames 3.5-foot hypersonic wind tunnel (test OH6)

The results of a hypersonic wind tunnel test program conducted using a 0.0175 scale thin-skin thermocouple model of the Space Shuttle Orbiter to obtain aerodynamic heat transfer data on the Orbiter under simulated reentry conditions were presented. The test program was conducted at a Mach number of 7.3 and a freestream Reynolds number ranging between 1.0 and 6.0 million/foot. The model was tested for angles of attack ranging between 10 deg and 30 deg and a sideslip angle of 0 deg. The model was constructed of 15-5 PH stainless steel with the instrumented areas machined to a nominal skin thickness of 0.030 in. The model instrumentation consisted of 288 iron-constantan thermocouples spot welded to the skin inner surface, but only 75 of these were used in this test program. A high-speed, analog-to-digital data acquisition system was used to record data on magnetic tape.

Dye, W. H.↗

NASA NTRS1973

Aerodynamic investigations on a 0.004 scale model MCR 0074 baseline space shuttle launch vehicle at Mach numbers between 0.6 and 4.96

A test of a 0.004-scale MCR 0074 Baseline Launch Configuration Space Shuttle model was conducted in the NASA-MSFC 14 x 14-inch Trisonic Wind Tunnel (MSFC TWT 566). The objective of the test was to determine the effects of model parametric variations on aerodynamic static stability characteristics over a Mach number range from 0.6 to 4.96. Angles-of-attack from minus 10 deg to plus 10 deg at 0 deg sideslip and angles-of-sideslip from minus 10 deg to plus 10 deg at minus 5 deg, 0 deg, and plus 5 deg angle-of-attack were investigated. The basic configuration investigated was the integrated vehicle consisting of the orbiter, and external tank, and two solid rocket boosters. It was designated 03T9S3.

Ramsey, P.↗

NASA NTRS1974

Aerodynamic results of support system interference effects tests conducted in NASA/ARC 6 by 6-foot supersonic wind tunnel using an 0.015-scale model of the configuration 14OA/B SSV orbiter (OA59), volume 1

An experimental aerodynamic investigation was conducted in the NASA/ARC 6- by 6-foot supersonic wind tunnel on an 0.015-scale configuration 140A/B SSV Orbiter model. The primary objective was to determine the extent aerodynamic simulation is compromised by sting base mounting with MPS nozzles removed. Both a conventional sting (through the base) and an alternate model mounting system were utilized. The alternate mounting system consisted of a non-metric blade strut, which approximated the vertical tail and entered the model through the upper aft section of its fuselage. The model was tested both in and out of the presence of a dummy sting with and without MPS nozzles when on the alternate mounting system. Data were obtained at Mach numbers from 0.6 through 2.0, a Reynolds number of 2.5 million per foot, angles of attack from -4 through 14 degrees, angles of sideslip from -15 through 15 degrees, elevon deflections of 0 and 15 degrees, and bodyflap deflections of -11.7, 0, and 16.3 degrees.

Campbell, J. H., II↗

DOE OSTI2023

CompLaB v1.0: a scalable pore-scale model for flow, biogeochemistry, microbial metabolism, and biofilm dynamics

Abstract. Microbial activity and chemical reactions in porous media depend on the local conditions at the pore scale and can involve complex feedback with fluid flow and mass transport. We present a modeling framework that quantitatively accounts for the interactions between the bio(geo)chemical and physical processes and that can integrate genome-scale microbial metabolic information into a dynamically changing, spatially explicit representation of environmental conditions. The model couples a lattice Boltzmann implementation of Navier–Stokes (flow) and advection–diffusion-reaction (mass conservation) equations. Reaction formulations can include both kinetic rate expressions and flux balance analysis, thereby integrating reactive transport modeling and systems biology. We also show that the use of surrogate models such as neural network representations of in silico cell models can speed up computations significantly, facilitating applications to complex environmental systems. Parallelization enables simulations that resolve heterogeneity at multiple scales, and a cellular automaton module provides additional capabilities to simulate biofilm dynamics. The code thus constitutes a platform suitable for a range of environmental, engineering and – potentially – medical applications, in particular ones that involve the simulation of microbial dynamics.

58 GEOSCIENCES↗

NASA NTRS1984

Results of a wind tunnel/flight test program to compare afterbody/nozzle pressures on a 1/12 scale model and an F-15 aircraft

In 1975 NASA Dryden Flight Research Facility received the No. 2 prototype F-15 aircraft from the USAF to conduct the F-15 Propulsion/Airframe Interactions Program. About the same time, NASA Langley Research Center acquired a 1/12 scale F-15 propulsion model, whose size made it suitable for detailed afterbody/nozzle static pressure distribution studies. Close coordination between Langley and Dryden assured identical orifice locations and nozzle geometries on the model and aircraft. This paper discusses the sequence of the test programs and how retesting the model after completion of the flight tests greatly increased the ability to match hardware and test conditions. The experience gained over the past decade from involvement in the program should prove valuable to any future programs attempting to match wind tunnel and flight test conditions and hardware.

Pendergraft, O. C., Jr.↗

NASA NTRS1975

Landing impact studies of a 0.3-scale model air cushion landing system for a Navy fighter airplane

An experimental study was conducted in order to determine the landing-impact behavior of a 0.3-scale, dynamically (but not physically) similar model of a high-density Navy fighter equipped with an air cushion landing system. The model was tested over a range of landing contact attitudes at high forward speeds and sink rates on a specialized test fixture at the Langley aircraft landing loads and traction facility. The investigation indicated that vertical acceleration at landing impact was highly dependent on the pitch angle at ground contact, the higher acceleration of approximately 5g occurring near zero body-pitch attitude. A limited number of low-speed taxi tests were made in order to determine model stability characteristics. The model was found to have good pitch-damping characteristics but stability in roll was marginal.

Leland, T. J. W.↗

NASA NTRS2010

The Vertical Structure of Relative Humidity and Ozone in the Tropical Upper Troposphere: Intercomparisons Among In Situ Observations, A-Train Measurements and Large-Scale Models

In situ measurements in the tropics have shown that in regions of active convection, relative humidity with respect to ice in the upper troposphere is typically close to saturation on average, and supersaturations greater than 20% are not uncommon. Balloon soundings with the cryogenic frost point hygrometer (CFH) at Costa Rica during northern summer, for example, show this tendency to be strongest between 11 and 15.5 km (345-360 K potential temperature, or approximately 250-120 hPa). this is the altitude range of deep convective detrainment. Additionally, simultaneous ozonesonde measurements show that stratospheric air (O3 greater than 150 ppbv) can be found as low as approximately 14 km (350 K/150 hPa). In contrast, results from northern winter show a much drier upper troposphere and little penetration of stratospheric air below the tropopause at 17.5 km (approximately 383 K). We show that these results are consistent with in situ measurements from the Measurement of Ozone and water vapor by Airbus In-service airCraft (MOZAIC) program which samples a wider, though still limited, range of tropical locations. To generalize to the tropics as a whole, we compare our insitu results to data from two A-Train satellite instruments, the Atmospheric Infrared Sounder (AIRS) and the Microwave Limb Sounder (MLS) on the Aqua and Aura satellites respectively. Finally, we examine the vertical structure of water vapor, relative humidity and ozone in the NASA Goddard MERRA analysis, an assimilation dataset, and a new version of the GEOS CCM, a free-running chemistry-climate model. We demonstrate that conditional probability distributions of relative humidity and ozone are a sensitive diagnostic for assessing the representation of deep convection and upper troposphere/lower stratosphere mixing processes in large-scale analyses and climate models.

Selkirk, Henry B.↗

NASA NTRS1975

Results of investigations with an 0.015-scale model (49-0) of the Rockwell International space shuttle vehicle 140A/B configuration with modified OMS pods and elevons in the AEDC VKF tunnel B (0A79)

Aerodynamic data obtained from wind tunnel tests of an 0.015-scale space shuttle vehicle Orbiter model of a 140A/B configuration with modified orbital manuevering system pods and elevons are documented. Force data was obtained at various control surface settings and Reynolds numbers in the angle of attack range of 15 deg to 45 deg and at angles of sideslip of -5 deg to +5 deg. Control surface variables included elevon, rudder, speed brake, and body flap configurations.

Esparza, V.↗

NASA NTRS1974

Results of wind tunnel tests at Mach 5 on the .004 scale model 2A configuration space shuttle to determine proximity effects and orbiter control effectiveness during orbiter/external tank abort separation (IAG)

Results from tests in the NASA/MSFC Trisonic Wind Tunnel on 0.004-Scale Orbiter and External Tank Force Models in Close Proximity (RTLS Abort Separation Conditions) are presented. The primary test objectives were to obtain data concerning proximity effects on the aerodynamic forces and moments experienced by Vehicle 2A Configuration Shuttle Orbiter and External Tank during an abort separation (Return to Launch Site) at a Mach number of 5. Additionally, data on orbiter control effectiveness during such an abort was obtained. Proximity effects were investigated for relative angles of incidence from minus 5 deg to plus 10 deg of the orbiter FRL with respect to the external tank centerline over a range of vertical and longitudinal displacements from the mated position to 2.5 tank diameters below and 3 tank diameters aft of the mated position.

Garton, W. P.↗

NASA NTRS1976

An investigation in the MSFC TWT to determine spoiler effects on wing loads and elevon hinge moments utilizing 0.004-scale models (77-0 and 74-OTS) of the shuttle vehicle 5 configuration (IA125)

Information is presented for wind tunnel tests (IA125) of a 0.004-scale orbiter, external tank, and solid rocket motor integrated vehicle model (77-0 and 74-OTS) in the MSFC Trisonic Wind Tunnel. These tests were conducted in support of MCR's 1344 and 1346. Data from these tests provide spoiler effects on wing bending/torsion and elevon hinge moments, elevon effectiveness data and the influence of solid plumes from Mach numbers of 0.6 through 2.74 at angles of attack and sideslip from -10 through 10 degrees.

Allen, E. C.↗

NASA NTRS1976

Results of an investigation of Reynolds effects on integrated vehicle elevon hinge moments and wing panel loads obtained with 0.010 scale model 72 OTS in the Rockwell trisonic wind tunnel (IA141)

Wind tunnel investigations were conducted on an 0.010-scale representation of the VL70-000140C Integrated Space Shuttle Launch Vehicle. The primary test objective was to obtain Reynolds number effects on orbiter elevon hinge moments and wing bending/torsional moments. Launch vehicle aerodynamic force data were also recorded. The elevon hinge moments, wing bending/torsional moments, and vehicle force data were recorded over an angle of attack range of -6 deg to +6 deg, an angle of sideslip range of -6 deg to +6 deg, at Mach numbers of 0.6, 0.975, 1.05 and 1.25. The Reynolds number was varied from a minimum of 4.5 million/foot to a maximum of 11.5 million/foot. The complete integrated configuration was tested with the orbiter elevons set at 0 deg and deflected to 9 deg on the outboard elevon and 10 deg on the inboard elevon. Testing was conducted in the TWT 19.7% porous transonic test section with the model sting mounted through the orbiter base. All aerodynamic force data were obtained from internal strain gage balance located in the orbiter.

Mennell, R. C.↗

DOE OSTI2026

Hacking Kilometer-Scale Models: A Participative Model for Climate Information

In May 2025, nearly 700 participants from all around the world coalesced at 10 regional nodes and a few satellite nodes to take part in a global hackathon of kilometer-scale (horizontal grid spacing < 10 km) regional and global Earth system models. Exciting science is emerging from these efforts, ranging across novel model analysis, new ways of integrating with satellite data, and emulation with machine learning. New technologies were trialed that enable the community to work in new and complementary ways to democratize access to global information at a local scale from a set of the world’s highest-resolution climate models. The hackathon demonstrated how exascale data can be organized to be accessible to anyone. Fundamentally, the community could apply these techniques and technologies to move toward more participative models for coproduction and delivery of diverse sources of climate information for climate scientists and citizens alike.

Climate models↗

NASA NTRS1975

Results of experimental tests in the MSFC 14 x 14 inch trisonic wind tunnel on a .004 scale model space shuttle integrated vehicle 5 (model 77-O, 74-TS) to relieve wing loads during ascent (IA71)

Results are presented for the 0.004-scale orbiter, external tank, and solid rocket boosters combined as an integrated vehicle in a trisonic wind tunnel at mach numbers from 0.6 to 2.0. The primary test objective was to determine the effectiveness of several methods in relieving the Orbiter wing bending and torsion loads and moments during launch. Effects of several midwing spoilers, termed flipper doors, and Orbiter/external tank incidence were investigated. Photographs are included.

Allen, E. C.↗

NASA NTRS1949

Aerodynamic Characteristics of a 0.5-Scale Model of the Fairchild XSAM-N-2 Lark Missile at High Subsonic Speeds

An investigation was conducted to determine the longitudinal- and lateral-stability characteristics of a 0.5-scale moue1 of the Fairchild Lark missile, The model was tested with 0 deg and with 22.5 deg of roll. Three horizontal wings having NACA 16-009, 16-209, and 64A-209 sections were tested. Pressures were measured on both pointed and blunt noses. The wind-tunnel-test data indicate that rolling the missile 22.5 deg. had no serious effect on the static longitudinal stability. The desired maneuvering acceleration could not be attained with any of the horizontal wings tested, even with the horizontal wing flaps deflected 50 deg. The flaps on the 64A-209 wing (with small trailing-edge angles and flat sides) were effective at all flap deflections, while the flaps on the 16-series wings (with large trailing-edge angles) lost effectiveness at small flap deflections. The data showed that rolling moment existed when the vertical wing flaps were deflected with the model at other than zero angle of attack. A similar rolling moment probably would be found . with the horizontal wing flaps deflected and the model yawed.

Martin, Andrew↗

NASA NTRS1991

BVI impulsive noise reduction by higher harmonic pitch control - Results of a scaled model rotor experiment in the DNW

Results are presented of a model rotor acoustics test performed to examine the benefit of higher harmonic control (HHC) of blade pitch to reduce blade-vortex interaction (BVI) impulsive noise. A dynamically scaled, four-bladed, rigid rotor model, a 40-percent replica of the B0-105 main rotor, was tested in the German Dutch Wind Tunnel. Noise characteristics and noise directivity patterns as well as vibratory loads were measured and used to demonstrate the changes when different HHC schedules were applied. Dramatic changes of the acoustic signatures and the noise radiation directivity with the HHC phase variations are found. Compared to the baseline conditions (without HHC), significant mid-frequency noise reductions of locally 6 dB are obtained for low-speed descent conditions where GVI is most intense. For other rotor operating conditions with less intense BVI there is less or no benefit from the use of HHC. LF noise and vibratory loads, especially at optimum noise reduction control settings, are found to increase.

Splettstoesser, Wolf R.↗