Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixture experiment models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Measurements of scramjet thrust in shock tunnels

By using results obtained in tests on supersonic combustion of hydrogen in air, the conditions governing model size and operating pressure levels for shock tunnel experiments on models of flight vehicles with scramjet propulsion are established. It is seen that large models are required. The development of the stress wave force balance is then described, and its use as a method of measuring thrust/drag on such models is discussed. Test results on a simple, fully integrated scramjet model, with intakes, combustion chambers, thrust surfaces and exterior surfaces, using a 13 percent silane 87 percent hydrogen fuel mixture, showed that a steady state with thrust generation could be achieved within the shock tunnel test time, and the thrust could be measured. Results are presented for a range of stagnation enthalpies, and show that the scramjet model produces net positive thrust at velocities up to 2.4 km/sec.

Stalker, R. J.↗

CFD Predictions of Boiling Regime Transitions during Line Chilldown validated against a 1G LN2 Experiment

Introduction Before filling a propellant tank on the ground or in Space, the transfer line between the donor and receiver tanks must be cooled down preferably by sacrificing a minimum amount of the cryogenic fluid. The cryogenic line chill-down process involves a transition between different flow boiling regimes, namely, film boiling, transition film boiling, and nucleate boiling which are complex and may be quite gravity-dependent. Capturing these boiling phenomena and predicting the transition between them in a CFD framework is new and challenging both for 1g and microgravity applications. Materials & Methods The present work addresses this challenge by employing a two-phase Eulerian approach in the context of a homogeneous fluid mixture together with the Lee phase change model to capture the film boiling regime of the chill-down process using ANSYS Fluent®. The nucleate boiling regime is predicted by incorporating an in-house developed sub-grid model that accounts for bubble nucleation, bubble growth, bubble departure diameter, and their shedding frequency. The sub-grid model is encoded and implemented into Fluent via a user-defined function for the wall-fluid heat flux calculations. The mathematical formulation and numerical implementation of the CFD model are described in detail. The coupled CFD-Subgrid model is validated against published experimental data for liquid nitrogen chill-down of a heated stainless-steel pipe in 1g. Results Numerical simulation results show good agreements between the CFD predictions of the wall temperature evolution, rewetting temperature, and transition between film and nucleate boiling, with the experimental measurements published by Darr et al [2] for several different LN2 flowrates in the vertical pipe orientation. The CFD predictions for the wall temperature distribution indicate a rapid quenching of the wall at two upstream and downstream temperature sensing locations as compared to the experimental measurement. The only tuning parameter in the CFD model is the Lee mass transfer coefficient. The CFD Model predicts the Liedenfrost rewetting temperature in close agreement with the experiment. This marks a transition between stable and transitionary flow boiling regimes. The CFD-predicted boiling curve for the downstream sensor location is also compared against its experimental counterpart and indicates that the model is able to predict all the key temperature and heat flux parameters during the transitions from stable to transitionary film boiling to nucleate boiling in close agreement with the experiment. A sequence of predicted volume fraction, and temperature contours depicting these transitions will be presented.

Evaporation Condensation↗

Mixed neutralino dark matter in nonuniversal gaugino mass models

We have considered nonuniversal gaugino mass models of supergravity, arising from a mixture of two superfield contributions to the gauge kinetic term, belonging to a singlet and a nonsinglet representation of the grand unified theory group. In particular we analyze two models, where the contributing superfields belong to the singlet and the 75-dimensional, and the singlet and the 200-dimensional representations of SU(5). The resulting lightest superparticle is a mixed bino-Higgsino state in the first case and a mixed bino-wino-Higgsino state in the second. In both cases one obtains cosmologically compatible dark matter relic density over broad regions of the parameter space. We predict promising signals in direct dark matter detection experiments as well as in indirect detection experiments via high energy neutrinos coming from their pair annihilation in the Sun. Besides, we find interesting {gamma}-ray signal rates that will be probed in the Fermi gamma-ray space telescope. We also expect promising collider signals at LHC in both cases.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The Dynamics of Megafire Smoke Plumes in Climate Models: Why a Converged Solution Matters for Physical Interpretations

As the climate system warms, megafires have become more frequent with devastating effects. A byproduct of these events is the creation of smoke plumes that can rise into the stratosphere and spread across the globe where they reside for many months. To gain a deeper understanding of the plume dynamics, global climate simulations of a megafire were performed at a wide range of grid spacings from 2.0° down to 7 km, including a 7 km nonhydrostatic experiment. The analysis focuses on how the resolved dynamics affects the specification of the plume characteristics such as injection height and black carbon (BC) mass. Prior studies initialize the smoke plume at one or a few grid points and this is shown here to produce severely dissipative dynamics. In order to validate such simulations with observations, enhancements of the plume characteristics to offset the dissipation is necessary. Using a numerically converged simulation, sensitivity tests show that to approximate the observed stratospheric lifetime, a reduction in BC fraction by 50% is necessary for external mixtures. The vorticity dynamics of the plume is also analyzed with a Lagrangian budget to understand the mechanisms responsible for the evolution of a collocated anticyclonic vortex. The results can be distilled down into a simple conceptual model. As the plume rises, the air diverges at the top of the updraft where the largest concentrations of smoke are found. This divergence induces a dilution of the background cyclonic absolute vorticity producing an anticyclonic vortex. Vortex decay occurs from opposite arguments.

54 ENVIRONMENTAL SCIENCES↗

Mysterious SiB 3 : Identifying the Relation between α- and β-SiB 3

Binary silicon boride SiB 3 has been reported to occur in two forms, as disordered and nonstoichiometric α-SiB 3–x , which relates to the α-rhombohedral phase of boron, and as strictly ordered and stoichiometric β-SiB 3 . Similar to other boron-rich icosahedral solids, these SiB 3 phases represent potentially interesting refractory materials. However, their thermal stability, formation conditions, and thermodynamic relation are poorly understood. Here, we map the formation conditions of α-SiB 3–x and β-SiB 3 and analyze their relative thermodynamic stabilities. α-SiB 3–x is metastable (with respect to β-SiB 3 and Si), and its formation is kinetically driven. Pure polycrystalline bulk samples may be obtained within hours when heating stoichiometric mixtures of elemental silicon and boron at temperatures 1200–1300 °C. At the same time, α-SiB 3–x decomposes into SiB6 and Si, and optimum time-temperature synthesis conditions represent a trade-off between rates of formation and decomposition. The formation of stable β-SiB 3 was observed after prolonged treatment (days to weeks) of elemental mixtures with ratios Si/B = 1:1–1:4 at temperatures 1175–1200 °C. The application of high pressures greatly improves the kinetics of SiB 3 formation and allows decoupling of SiB 3 formation from decomposition. Quantitative formation of β-SiB 3 was seen at 1100 °C for samples pressurized to 5.5–8 GPa. β-SiB 3 decomposes peritectoidally at temperatures between 1250 and 1300 °C. The highly ordered nature of β-SiB 3 is reflected in its Raman spectrum, which features narrow and distinct lines. In contrast, the Raman spectrum of α-SiB 3–x is characterized by broad bands, which show a clear relation to the vibrational modes of isostructural, ordered B 6 P. The detailed composition and structural properties of disordered α-SiB 3–x were ascertained by a combination of single-crystal X-ray diffraction and 29 Si magic angle spinning NMR experiments. Notably, the compositions of polycrystalline bulk samples (obtained at T ≤ 1200 °C) and single crystal samples (obtained from Si-rich molten Si–B mixtures at T > 1400 °C) are different, SiB 2.93(7) and SiB 2.64(2) , respectively. The incorporation of Si in the polar position of B 12 icosahedra results in highly strained cluster units. This disorder feature was accounted for in the refined crystal structure model by splitting the polar position into three sites. The electron-precise composition of α-SiB 3–x is SiB 2.5 and corresponds to the incorporation of, on average, two Si atoms in each B 12 icosahedron. Accordingly, α-SiB 3–x constitutes a mixture of B 10 Si 2 and B 11 Si clusters. The structural and phase stability of α-SiB 3–x were explored using a first-principles cluster expansion. The most stable composition at 0 K is SiB 2.5 , which however is unstable with respect to the decomposition β-SiB 3 + Si. Modeling of the configurational and vibrational entropies suggests that α-SiB 3–x only becomes more stable than β-SiB 3 at temperatures above its decomposition into SiB 6 and Si. Hence, we conclude that α-SiB 3–x is metastable at all temperatures. Density functional theory electronic structure calculations yield band gaps of similar size for electron-precise α-SiB 2.5 and β-SiB 3 , whereas α-SiB 3 represents a p-type conductor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hot hydrogen atom reactions moderated by H2 and He

Photolysis experiments were performed on the H2-CD4-NH3 and He-CD4-NH3 systems. The photolysis (1849 A) involved only NH3. Mixtures of H2:CD4:NH3 included all combinations of the ratios (200,400,800):(10,20,40):4. Two He:CD4:NH3 mixtures were examined where the ratios equalled the combinations 100:(10,20):4. Abstraction of a D from CD4 by the photolytically produced hot hydrogen from ammonia was monitored by mass spectrometric determination of HD. Both experiment and semiempirical hot-atom theory show that H2 is a very poor thermalizer of hot hydrogens with excess kinetic energy of about 2 eV. Applications of the hard-sphere collision model to the H2-CD4-NH3 system resulted in predicted ratios of net HD production to NH3 decomposition that were two orders of magnitude smaller than the experimental ratios. On the other hand, helium is found to be a very efficient thermalizer; here, the classical model yields reasonable agreement with experiments. Application of a semiempirical hot-atom program gave quantitative agreement with experiment for either system.

Aronowitz, S.↗

Low temperature autoignition of 5-membered ring naphthenes: Effects of substitution [Low temperature autoignition study of substituted 5-membered ring naphthenes]

The development and design of future internal combustion engines requires fundamental understanding and the capability to model the autoignition and pollutant formation behavior of petroleum-based and other fuels. Naphthenes are an important constituent of gasoline, and they can comprise larger portions of unconventionally-derived gasoline. There is a lack of data and validated models for 5-membered ring naphthenes. In this work, the autoignition characteristics of cyclopentane, and two of its substituted analogues, methylcyclopentane, and ethylcyclopentane are investigated using a twin-piston rapid compression machine. Each fuel is studied at engine-representative conditions: 20, 50 bar and 700-980K, with mixtures containing stoichiometric fuel/oxygen ratios at various extents of dilution with inert gases. Negative temperature coefficient (NTC) behavior is observed for cyclopentane, though first-stage ignition and associated low temperature heat release behavior are only evident at temperatures below that for the transition to NTC. Pressure is found to have a larger impact on the reactivity than oxygen dilution, with both effects amplified in the NTC region. The cyclopentane experiments in this study are challenged by the sensitivity of this molecule to non-uniform, or mild ignition phenomena within the NTC region. The addition of saturated sidechains in methyl- and ethylcyclopentane significantly increases the reactivity of the molecules, especially at low temperature and NTC conditions. At the highest temperatures though, there is little difference between the three naphthenes. Typical two-stage ignition behavior is observed across a wide range of temperatures for these alkyl cyclopentanes with no mild ignition observed within the NTC region. A recently developed model for cyclopentane is extended to include reactions for methylcyclopentane, and this is used to simulate the new experiments. The simulation results indicate that low temperature reactivity of cyclopentane is dominated by HO 2 elimination of the RO 2 species producing cyclopentene, and this inhibits autoignition since it is a very stable molecule. When a methyl group is substituted on the ring, additional RO 2 isomerization pathways are available, and these substantially increase the fuel reactivity. HO 2 elimination is also important with methylcyclopentane, and this leads to significant production of cyclic olefins which can further react to produce diolefins. Furthermore, these findings are consistent with observations that have been made in other experimental apparatuses.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Produced Water and Waste Heat-aided Blowdown Water Treatment: Using Chemical and Energy Synergisms for Value Creation

The project objective was to develop a cooling blowdown water (BDW) treatment process utilizing produced water (PW) and low-grade heat to maximize water reuse and saleable by-product generation while reducing chemical and energy footprints of the treatment. The proposed treatment process consists of mixing, softening, organics and suspended solids removal, reverse osmosis (RO), thermal desalination, and brine electrolysis. BDW samples collected from a local coal-fired power plant and PW samples from two shale gas production wells were used in this study. Each treatment unit was first designed and tested to quantify its treatment efficiency, and its chemical and energy requirements. In addition, a process model was developed and model simulations were conducted based on the experimental results and literature data to optimize the treatment process. A techno-economic analysis was conducted to quantify chemical and energy savings as well as production of 10-lb brine as a saleable product. With the field-collected BDW and PW samples, mixing experiments determined a volumetric mixing ratio 10:1 (BDW:PW) resulted in the best performance of multivalent ions removal and largest chemical savings for softening. Softening of the BDW/PW mixtures using alkaline chemicals (Na 2 CO 3 and NaOH) achieved 95%-100% removal of scaling-forming cations (Ca, Mg, Fe, Ba, Sr) and 60% of silicon, and 10% of total organic carbon (TOC). The mixing and softening treatments yielded an effluent with total dissolved solids (TDS) concentration of 23 g/L. Activated carbon (AC) filtration removed TOC to a low level (< 3 mg/L) and further removed remaining scale-forming divalent metals and silica from the softened water. The AC filtration resulted in a slight reduction of TDS from 23 g/L to 20 g/L, leaving behind only mostly monovalent ions (i.e., sodium and chloride) in the filtered water. These pretreatments yielded a feed water that met the criteria of the downstream reverse osmosis (RO) to prevent membrane fouling. A cross-flow RO system was used to further concentrate the TDS of the AC effluent. Various factors including TDS, pH, and applied pressure were examined and optimal conditions were determined for the co-treatment process. An integrated process consisting of mixing, softening, AC filtration and RO was used to treat a continuous flow (0.25 – 1.2 L/min, or 0.07 – 0.32 gpm) and successfully generated RO permeate as product water (TDS < 0.5 g/L) for reuse in cooling operation, and a concentrate (TDS ~ 45 g/L) to be further treated in a thermal desalination unit. These flow rates meet the FOA’s criterion of 0.01 – 1 gpm. Overall, the co-treatment of BDW/PW allowed shorter ramp-up time compared to treatment of BDW alone. It resulted in 40% and 55% savings of Na 2 CO 3(s) and NaOH, respectively, compared to treating the BDW and PW individually for the same level of softening. The co-treatment also resulted in a 29% energy saving compared to treatment of BDW only for the level of TDS concentration. A thermal desalination system was designed using CFD simulations and manufactured in the WVU Innovation Hub for further treatment of the RO concentrate to generate 10-lb brine. The system has a design flow rate of 2 gpm and has been successfully tested. A bench-scale brine electrolysis system was developed for on-site generation of chlorine/hypochlorite (Cl 2 /OCl - ) and caustic soda (NaOH) as useful chemicals for the co-treatment process. Using salt solutions (0.5 M and 1 M), the system achieved faradaic efficiencies of 93%-97% and 70%-77% for caustic soda and chlorine/hypochlorite generation, respectively. An economic analysis showed that the electricity costs for on-site generation of these chemicals were significantly lower than the chemical prices offered by suppliers. An industrial-scale process model consisting of mixing, softening, AC filtration, RO, thermal desalination, and brine electrolysis was developed using the Aspen Plus V9 in conjunction with Aspen Custom Modeler V9. The model serves as a solvable Aspen Plus model and as basis to form the costing infrastructure. In addition, techno-economic analysis considering capital, operating, and transportation costs was conducted. An optimization solution showed that produced water for mixing is still advantageous in low quantities. The optimum solution approaches a leveled cost of water (LCW) of 2 $/m 3 which becomes cost competitive with nominal water treatment prices.

20 FOSSIL-FUELED POWER PLANTS↗

Kinetics of biological methane oxidation in the presence of non-methane organic compounds in landfill bio-covers

In this experimental program, the effects of non-methane organic compounds (NMOCs) on the biological methane (CH{sub 4}) oxidation process were examined. The investigation was performed on compost experiments incubated with CH{sub 4} and selected NMOCs under different environmental conditions. The selected NMOCs had different concentrations and their effects were tested as single compounds and mixtures of compounds. The results from all experimental sets showed a decrease in CH{sub 4} oxidation capacity of the landfill bio-cover with the increase in NMOCs concentrations. For example, in the experiment using compost with 100% moisture content at 35 deg. C without any NMOCs the V{sub max} value was 35.0 mug CH{sub 4}h{sup -1}g{sub wetwt}{sup -1}. This value was reduced to 19.1 mug CH{sub 4}h{sup -1}g{sub wetwt}{sup -1} when mixed NMOCs were present in the batch reactors under the same environmental conditions. The experimental oxidation rates of CH{sub 4} in the presence of single and mixed NMOCs were modeled using the uncompetitive inhibition model and kinetic parameters, including the dissociation constants, were obtained. Additionally, the degradation rates of the NMOCs and co-metabolic abilities of methanotrophic bacteria were estimated.

54 ENVIRONMENTAL SCIENCES↗

Rationalizing Acidic Oxygen Evolution Reaction over IrO 2 : Essential Role of Hydronium Cation

The development of active, stable, and more affordable electrocatalysts for acidic oxygen evolution reaction (OER) is of great importance for the practical application of electrolyzers and the advancement of renewable energy conversion technologies. Currently, IrO 2 is the only catalyst with high stability and activity, but a high cost. Further optimization of the catalyst is limited by the lack of understanding of catalytic behaviors at the acid-IrO 2 interface. Here, in strong interaction with the experiment, we develop an explicit model based on grand-canonical density function theory (GC-DFT) calculations to describe acidic OER over IrO 2 . Compared to the explicit models reported previously, hydronium cations (H 3 O + ) are introduced at the electrochemical interface in the current model. As a result, a variation in stable IrO 2 surface configuration under the OER operating condition from previously proposed complete *O-coverage to a mixture coverage of *OH and *O is revealed, which is well supported by in situ Raman measurements. In addition, the accuracy of predicted overpotential is increased in comparison with the experimentally measured. More importantly, in this study, an alteration of the potential limiting step from previously identified *O→*OOH to *OH→*O is observed, which opens new opportunities to advance the IrO 2 -based catalysts for acidic OER.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Swelling Inhibition of Liquid Crystalline Colloidal Montmorillonite and Beidellite Clays by DNA

Exploring the interaction of nucleic acids with clay minerals is important to understand such issues as the persistence in soils of biomolecules and the appearance of genetic polymers in prebiotic environments. Colloidal dispersions of double stranded DNA and clay nanosheets may also provide interesting model systems to study the statistical physics of mixtures of semi-flexible rods and plates. Here, we show that adding very small amounts of DNA to liquid-crystalline montmorillonite and beidellite smectite clay suspensions strongly widens the isotropic/nematic phase coexistence region. Moreover, a spectroscopic study shows that, upon DNA addition, the first DNA molecules adsorb onto the clay particles. Remarkably, synchrotron small-angle X-ray scattering experiments reveal that the average distance between the clay sheets, in the nematic phase at coexistence, decreases with increasing DNA concentration and that the inhibition of swelling by DNA becomes almost independent of clay concentration. We interpret this DNA-mediated attraction between clay nanosheets by bridging conformations of DNA strands (plates on a string structure). In addition to bridging, DNA chains can form "loops" between sections adsorbed on the same particle, giving rise to sheet repulsions due to protruding loops. Furthermore, this interpretation agrees with the observed inter-clay spacings being dependent only on the DNA concentration.

59 BASIC BIOLOGICAL SCIENCES↗

Overview of T and D–T results in JET with ITER-like wall

In 2021 JET exploited its unique capabilities to operate with T and D–T fuel with an ITER-like Be/W wall (JET-ILW). This second major JET D–T campaign (DTE2), after DTE1 in 1997, represented the culmination of a series of JET enhancements—new fusion diagnostics, new T injection capabilities, refurbishment of the T plant, increased auxiliary heating, in-vessel calibration of 14 MeV neutron yield monitors—as well as significant advances in plasma theory and modelling in the fusion community. DTE2 was complemented by a sequence of isotope physics campaigns encompassing operation in pure tritium at high T-NBI power. Carefully conducted for safe operation with tritium, the new T and D–T experiments used 1 kg of T (vs 100 g in DTE1), yielding the most fusion reactor relevant D–T plasmas to date and expanding our understanding of isotopes and D–T mixture physics. Furthermore, since the JET T and DTE2 campaigns occurred almost 25 years after the last major D–T tokamak experiment, it was also a strategic goal of the European fusion programme to refresh operational experience of a nuclear tokamak to prepare staff for ITER operation. The key physics results of the JET T and DTE2 experiments, carried out within the EUROfusion JET1 work package, are reported in this paper. Progress in the technological exploitation of JET D–T operations, development and validation of nuclear codes, neutronic tools and techniques for ITER operations carried out by EUROfusion (started within the Horizon 2020 Framework Programme and continuing under the Horizon Europe FP) are reported in (Litaudon et al Nucl. Fusion accepted), while JET experience on T and D–T operations is presented in (King et al Nucl. Fusion submitted).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ionic Transport Coefficients of Dense Plasmas without Molecular Dynamics

In this paper, we present a theoretical model that allows a fast and accurate evaluation of ionic transport properties of realistic plasmas spanning from warm and dense to hot and dilute conditions, including mixtures. This is achieved by combining a recent kinetic theory based on effective interaction potentials with a model for the equilibrium radial density distribution based on an average atom model and the integral equations theory of fluids. Lastly, the model should find broad use in applications where nonideal plasma conditions are traversed, including inertial confinement fusion, compact astrophysical objects, solar and extrasolar planets, and numerous present-day high energy density laboratory experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

World Ocean Circulation Experiment (WOCE) Young Investigator Workshops

The World Ocean Circulation Experiment (WOCE) Young Investigator Workshops goals and objectives are: a) to familiarize Young Investigators with WOCE models, datasets and estimation procedures; b) to offer intensive hands-on exposure to these models ard methods; c) to build collaborations among junior scientists and more senior WOCE investigators; and finally, d) to generate ideas and projects leading to fundable WOCE synthesis projects. To achieve these goals and objectives, the Workshop will offer a mixture of tutorial lectures on numerical models and estimation procedures, advanced seminars on current WOCE synthesis activities and related projects, and the opportunity to conduct small projects which put into practice the techniques advanced in the lectures.

Austin, Meg↗

Formulation and validation of a computational model for a dilute biomass slurry undergoing rotational mixing

In this paper we develop a computational model for the mixing and transport of a dilute biomass slurry. The objective was to create a sufficiently simple and efficient model for biomass transport that can be coupled with reaction models for the study of conversion of cellulosic biomass into fermentable sugars. Our target system is 5%-by-mass ..alpha..-cellulose, which is our proxy for more complex lignocellulosic biomass. In the authors' previous work, an experimental investigation with ..alpha..-cellulose under two vane-mixer configurations showed a bifurcation between a settling regime, for which settling effects dominate, and a suspended regime, for which solids are mostly suspended. Here, a mixed-fluid model was chosen, for which the model for the mixture-velocity field is the incompressible Navier-Stokes equations under the Boussinesq approximation for buoyancy. Solids transport includes solids motion due to diffusion, settling, advection, and shear. Comparison of simulated and experimental results show good agreement in the suspended regime, and in capturing the bifurcation rate. While the model captured well the distribution of solids in the settling regime, the model was incapable of capturing the high torque values seen in experiments with vanishing mixer rotation rate.

09 BIOMASS FUELS↗

Acoustic and electrical properties of Fe-Ti oxides with application to the deep lunar mantle

The overturn of titanium-rich mantle cumulates has been invoked to explain the structure and dynamics of the Moon. These dense cumulates are stable at the core-mantle boundary (CMB) and could explain field observations inferred from geophysical studies. Here, we report acoustic and electrical experiments on natural ilmenite-rutile aggregates up to 4.5 GPa and 1920 K. Seismic velocities show a weak pressure and temperature dependence, with Vs ~ 4.2 (+/-0.2) km/s and Vp ~8.0 (+/-0.2) km/s at the CMB conditions. Conductivity increases by a factor of 10 4 from 373 to 1920 K and is >10(3) S/m above 1573 K. Seismic and electrical models for the lunar mantle based on our results, considering mixtures of Fe-Ti oxides and olivine, indicate that field velocity and conductivity estimates are reproduced satisfactorily with 3-16 vol.% Fe-Ti oxides and 20 vol.% melt. Interactions between a Ti-rich, melt-bearing layer and the adjacent core likely affect the cooling and magnetic history of the Moon.

58 GEOSCIENCES↗

NbTaV-(Ti,W) refractory high-entropy alloys: Experiments and modeling

This study reports the design and development of ductile and strong refractory single-phase high-entropy alloys (HEAs) for high temperature applications, based on NbTaV with addition of Ti and W. Assisted by CALPHAD modeling, a single body-centered cubic solid solution phase was experimentally confirmed in the as-cast ingots using X-ray diffraction and scanning electron microscopy. The observed elemental segregation in each alloy qualitatively agrees with CALPHAD prediction. The Vickers microhardnesses (and yielding strengths) of the alloys are about 3 (and 3.5-4.4) times that those estimated from the rule of mixture. While NbTaTiVW shows an impressive yielding strength of 1,420 MPa with fracture strain of 20%, NbTaTiV exhibits exceptional compressive ductility at room temperature.

36 MATERIALS SCIENCE↗

Equations of state for polyethylene and its shock-driven decomposition products

We construct new equations of state (EOS) for high density and ultrahigh molecular weight polyethylene and their chemical decomposition products under shock loading. The former were built using the SESAME framework, based in part on new specific heat and thermal expansion data reported here. The products EOS was based on thermochemical modeling under the assumption of full thermodynamic and chemical equilibrium. The products are represented as the ideal mixture of bulk carbon in the form of diamond, H 2 , H, and CH 4 . In the process of building a new EOS for the products, we recalibrated our exponential-6 pair potential for methane in order to better agree with data that have appeared since its original parameterization. The polyethylene EOS were calibrated to thermal, thermomechanical, and shock data, and their performance was evaluated in hydrodynamic modeling of deep release experiments reported previously.

36 MATERIALS SCIENCE↗