Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “low temperatures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Practical low-temperature gasoline combustion for very high efficiency off-road, medium- and heavy-duty engines

Low-temperature gasoline combustion (LTGC) with additive-mixing fuel injection (AMFI) is a new combustion strategy that has been demonstrated to deliver 9%–25% better brake thermal efficiency than similar-sized market-leading diesel engines over the operating map. Moreover, the LTGC-AMFI engine shows near-zero smoke, and NOx emissions are 4–100 times lower than those of a diesel, sufficiently low that no aftertreatment, or only passive NOx aftertreatment, would be sufficient (diesel exhaust fluid is not required). LTGC-AMFI combustion is based on kinetically controlled compression ignition of a dilute charge with a variable amount of low-to-moderate fuel stratification. Fast combustion control is provided by adding minute amounts of an ignition-enhancing additive into the fuel each engine cycle to control its reactivity. This strategy was used to operate a medium-duty (MD) LTGC-AMFI engine at loads from idle to 16.3 bar BMEP and speeds from 600 to 2400 rpm with regular E10 gasoline, which covers nearly the entire operating map of a typical MD engine. Turbine-out temperatures were sufficient for an oxidation catalyst to control hydrocarbon and CO emissions. Autonomie simulations over the GEM ARB Transient and the GEM 55 mph Cruise driving cycles for class-6 trucks using this technology showed fuel economies of 8.1 and 11.4 mpg-gasoline-equivalent, respectively, corresponding to 18.6% and 13.4% improvements over a similar-size diesel engine. Engine-out NOx emissions were 0.024 and 0.01 g/bhp-h, respectively, well below current U.S. emission standards. These results show that switching from diesel to LTGC-AMFI engines would greatly reduce greenhouse gas (GHG) emissions for off-road, MD and HD applications, which will continue to rely on combustion engines because electrification is not practical in the foreseeable future. Finally, with their reduced fuel consumption, the lower cost of gasoline compared to diesel fuel, and much lower aftertreatment costs, LTGC-AMFI engines also offer a significantly lower total cost of ownership.

33 ADVANCED PROPULSION SYSTEMS↗

A Study of Low-Temperature Neutron Star Atmospheres

We present a study of how a low-temperature accreted atmosphere influences the emitted X-ray spectrum of a neutron star. The atmosphere models and spectra were computed with Zcode, a multigroup radiation transfer code developed at the Los Alamos National Laboratory. Though the underlying hot neutron star behaves as a blackbody, the atmosphere shifts the peak of spectrum away from a blackbody and toward higher energies, producing an emitted spectrum similar to a dilute blackbody. Quantifying the effects of this atmosphere will remove a source of uncertainty in X-ray observations and better constrain the mass-radius relation for neutron stars and thus the equation of state of dense matter. We present a suite of these atmospheres with varying compositions and temperatures as well as the resulting spectra.

79 ASTRONOMY AND ASTROPHYSICS↗

Influence of low temperatures of friction and wear

A brief review of studies on low-temperature friction are briefly reviewed. A facility and technique for studying friction both in air and in vacuum at temperatures of +20 and -190 C is described. Results of a wear study of structural steels operating together with chromium steel are presented. It is shown that reduction of the test temperature in vacuum leads in certain cases to marked increase of the wear magnitude and friction coefficient. This is associated not only with the general change of the mechanical properties of the materials but also with the influence of temperature reduction on the hardening and structural formation taking place in the surface layers during friction.

Udovenko, V. F.↗

Low temperature simulation of subliming boundary layer flow in Jupiter atmosphere

A low-temperature approximate simulation for the sublimation of a graphite heat shield under Jovian entry conditions is studied. A set of algebraic equations is derived to approximate the governing equation and boundary conditions, based on order-of-magnitude analysis. Characteristic quantities such as the wall temperature and the subliming velocity are predicted. Similarity parameters that are needed to simulate the most dominant phenomena of the Jovian entry flow are also given. An approximate simulation of the sublimation of the graphite heat shield is performed with an air-dry-ice model. The simulation with the air-dry-ice model may be carried out experimentally at a lower temperature of 3000 to 6000 K instead of the entry temperature of 14,000 K. The rate of graphite sublimation predicted by the present algebraic approximation agrees to the order of magnitude with extrapolated data. The limitations of the simulation method and its utility are discussed.

Chen, C. J.↗

Elastic constants at low temperatures - Recent measurements on technological materials at NBS

Solid-state low-temperature elastic properties have been experimentally studied at the NBS Cryogenic Division for four years. Most studies were between room temperature and liquid-helium temperature; some were only to liquid-nitrogen temperature. Two dynamic (high-frequency) experimental methods were used, pulse-echo and resonance, resulting in adiabatic elastic constants. The present paper reviews these studies for 47 technological materials - metals, alloys, and composites. The elastic constants primarily discussed are Young's modulus, the shear modulus, the bulk modulus (reciprocal compressibility), and Poisson's ratio. A summary table is presented to show which base metals tend to exhibit regular, irregular, or anomalous behavior in their elastic constant/temperature curves.

Ledbetter, H. M.↗

Low-Temperature CO-Oxidation Catalysts for Long-Life CO2 Lasers

Low-temperature CO-oxidation catalysts are necessary for closed-cycle pulsed CO2 lasers as well as for other applications, including air purification. The papers presented in this volume discuss several such catalysts, including information on catalyst preparation, techniques for enhancing catalyst performance, laboratory and laser test results, and mechanistic considerations.

Schryer, David R.↗

Low temperature performance of lithium/silver vanadium oxide cells

Lithium/silver vanadium oxide cells for low temperature applications have been developed. Prismatic and spirally wound AA cells were tested under constant load discharge of 0.3 to 1.8 amps or pulse discharge of 0.225 or 1.0 amps at temperatures from -40 to 25 C. At -40 C with current densities of 2.5 mA/cm2, 23 percent of theoretical capacity was achieved under constant load discharge and 40 percent of theoretical capacity was achieved under pulse test. Self-discharge estimates of 0.7 percent per year at 25 C were obtained from microcalorimetry. Preliminary safety testing of the cells revealed no violent performance under short circuit or crush tests.

Takeuchi, E. S.↗

Megawatt-Scale Low Temperature Electrolyzer Research Capability

The development and installation of a flexible low-temperature electrolyzer research capability at the multi-MW scale with integrated renewables will help lower the cost barrier to entry for electrolyzer manufactures needing at scale system and stack evaluation and enable more electrolyzer manufactures to accelerate to commercialization with building block scale demonstration and validation. This NREL capability represents a DOE HFTO investment to support the $1B DOE Clean Hydrogen Electrolysis Program working to achieve the Hydrogen Shot goal of $1 for 1 kg hydrogen in 1 decade, lower greenhouse gas emissions and criteria pollutants, build clean energy infrastructure, and provide pathways to private sector uptake.

electrical grid↗