Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface capturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

iButton and Tinytag snow/ground interface temperature measurements at Teller 27 and Kougarok 64 from 2022-2023, Seward Peninsula, Alaska

Snow/ground interface temperature measurements were collected at the NGEE Arctic Teller Road Site at mile marker 27 (TL_MM27) and at the Kougarok Road Site at mile marker 64 (KG_MM64) on the Seward Peninsula, Alaska. Data were collected between October 1, 2022 to September 18, 2023 using iButton Link DS1921G-F5# Thermochron miniature temperature sensors (https://www.ibuttonlink.com/products/ds1921g) and Tinytag TGP-4017 internal sensors (https://www.micronmeters.com/product/tgp-4017-internal-sensor-40-to-85-c-40-f-to-185-f) deployed across the Kougarok and Teller sites. These sensors are a cost-efficient way to collect snowpack temperatures at a higher spatial resolution than what is normally achieved. iButton data were collected every 4 hours, while Tinytag data were collected every 30 minutes. In total, data were collected from 196 iButtons and 26 Tinytags. This dataset contains four *.csv files of near-ground surface temperatures at various locations throughout each study site and two *.kml files of sensor locations. Data were collected throughout the snow cover season so that snowpack characteristics could be derived using the temperature data. Sensors were placed both inside and outside of vegetation to better capture the spatial variability of snow properties across each domain.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) was a 15-year research effort (2012-2027) to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy’s Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy’s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Implement and Test 3D Mortar Contact in BISON

We leverage the extension of the generation of mortar segment meshes to three dimensions in MOOSE’s framework to extend thermomechanical modeling capabilities to problems with three dimensions. A modular approach to gap heat transfer physics using the mortar finite element method was created and documented, mechanical contact was extended to three dimensions—including frictional behavior, performance and ease of use were improved, and steps towards scalability of solid mechanics problems involving contact were taken. Many of these new developments are demonstrated in the simulation of 3D light-water reactor (LWR) problems, where the thermomechanical interface problem is solved using the mortar finite element method. Usage of the mortar framework has improved convergence in 2D problems and has enabled employing friction in 3D problems, of which we show results of a short, local stack of 3D pellets. Consequently, the benefits of mortar in terms of solution convergence and quality are extended to three dimensions. Section 2 discusses fundamental developments that enabled the simulation of practical mortar problems in three dimensions and other general improvements, including the reduction of the derivative container size, the modification of dual basis computations when edge dropping (lack of secondary element projection) takes place, the improvement of conditioning when employing the VCP in-edge dropping conditions, and code usability and quality improvements. These latter code enhancements include the migration of tests using “old” mortar contact constraints to using dual mortar with a semi-smooth Newton solution strategy and the reuse of lower dimensional domains for straightforwardly setting up a mortar thermomechanical LWR problem, i.e. the MOOSE action is employed for mechanical contact and the thermal LWR action is employed to capture the gas conductance, contact, and radiation components of gap heat transfer physics. Independently of the mortar LWR thermal action, we developed a modular approach to gap heat transfer that resides in MOOSE and can be leveraged, e.g., in metallic fuel problems. This approach, whose code design based on MOOSE’s user objects to model specific physics was proposed by the maintenance activity, is detailed in Section 3. Based on the dual mortar finite element method, the frictional contact constraints were extended to three dimensions. A block sheared in two directions in and out of contact with a rigid plane is employed in Section 4 to show the way the approach handles changes in frictional states (e.g. stick to slip) within a competitive number of Newton iterations. Equations and numerical results on the use of the VCP with Cartesian Lagrange multipliers, whose combination enables their direct condensation, are described in Section 5.3. Two-dimensional and three-dimensional BISON LWR simulations are discussed in Section 6. Particularly, a stack of five eccentric pellets with a surface defect is simulated and the effect of pellet-cladding friction is assessed. Finally, conclusions are outlined in Section 7.

42 ENGINEERING↗
DOE OSTI2021

Hardware-Based Emulator with Deep Learning Model for Building Energy Control and Prediction Based on Occupancy Sensors’ Data

Heating, ventilation, and air conditioning (HVAC) is the largest source of residential energy consumption. Occupancy sensors’ data can be used for HVAC control since it indicates the number of people in the building. HVAC and sensors form a typical cyber-physical system (CPS). In this paper, we aim to build a hardware-based emulation platform to study the occupancy data’s features, which can be further extracted by using machine learning models. In particular, we propose two hardware-based emulators to investigate the use of wired/wireless communication interfaces for occupancy sensor-based building CPS control, and the use of deep learning to predict the building energy consumption with the sensor data. We hypothesize is that the building energy consumption may be predicted by using the occupancy data collected by the sensors, and question what type of prediction model should be used to accurately predict the energy load. Another hypothesis is that an in-lab hardware/software platform could be built to emulate the occupancy sensing process. The machine learning algorithms can then be used to analyze the energy load based on the sensing data. To test the emulator, the occupancy data from the sensors is used to predict energy consumption. The synchronization scheme between sensors and the HVAC server will be discussed. We have built two hardware/software emulation platforms to investigate the sensor/HVAC integration strategies, and used an enhanced deep learning model—which has sequence-to-sequence long short-term memory (Seq2Seq LSTM)—with an attention model to predict the building energy consumption with the preservation of the intrinsic patterns. Because the long-range temporal dependencies are captured, the Seq2Seq models may provide a higher accuracy by using LSTM architectures with encoder and decoder. Meanwhile, LSTMs can capture the temporal and spatial patterns of time series data. The attention model can highlight the most relevant input information in the energy prediction by allocating the attention weights. The communication overhead between the sensors and the HVAC control server can also be alleviated via the attention mechanism, which can automatically ignore the irrelevant information and amplify the relevant information during CNN training. Our experiments and performance analysis show that, compared with the traditional LSTM neural network, the performance of the proposed method has a 30% higher prediction accuracy.

Ye, Zhijing↗
DOE OSTI2025

Integrated CO 2 capture and hydrogenation in presence of Ru–Na 2 ZrO 3 : An in-situ study

Integrated CO 2 capture and conversion (ICCC) by hydrogenation is a promising strategy to utilize carbon dioxide and this work add to the effort to elucidate the catalytic hydrogenation mechanism using Ru based dual functional materials (DFM). Ru-Na 2 ZrO 3 DFMs, obtained through different wet methods, were evaluated for the first time and the relationship between Ru and support systematically investigated. The thermally stable and cyclable Ru-Na 2 ZrO 3 -a (obtained without filtration step) exhibited CO 2 conversion of 80% and a higher yield of CO at 400°C compared to previously tested DFM, while the Na depleted/Zr rich Ru-Na 2 ZrO 3 -b resulted in 90% selectivity to CH 4 with yield of 1.11 mmol/g at the same temperature. The in-situ experiments have provided conclusive evidence showing that CO 2 hydrogenation on the two Ru DFMs is fundamentally different. In Ru-Na 2 ZrO 3 -a, the monoclinic Na 2 ZrO 3 support acted as the active centre (not as promoter) for CO 2 bridging binding and hydrogenation to CH 4 at the metal-support interface through associative formate pathway with limited further reduction to methane due to lack of H 2 spillover from the small and well dispersed Ru NPs, which results in CO desorption. Conversely, abundant clusters of larger Ru NPs in Ru-Na 2 ZrO 3 -b, led to CH 4 production due to co-existent Ru on-top direct dissociation of CO 2 (preferential) and monodentate formate adsorption and further methanation. Alkali zirconates doped metals, and their synthesis method could thus play a crucial role in designing tuneable heterogeneous catalysis in C 1 chemistry, which could significantly benefit the environment by lowering CO 2 levels, encouraging cleaner industrial practices, supporting a circular economy, and converting waste CO 2 into valuable products.

36 MATERIALS SCIENCE↗
DOE OSTI2026

From bulk to surface: Structure and dynamics of amorphous alumina from deep potential molecular dynamics

Understanding the atomic-scale structure and dynamics of amorphous oxide surfaces is essential for interpreting their chemical reactivity, mechanical stability, and interfacial behavior, yet direct experimental characterization remains challenging. We employ Deep Potential (DP) molecular dynamics to generate large-scale, ab initio -quality models of amorphous Al 2 O 3 bulk glasses and melt-quenched free surfaces, enabling a quantitative analysis of both structure and relaxation dynamics with statistical confidence inaccessible to direct ab initio simulation. The trained DP model reproduces experimental liquid and glass structure, captures the cooling-rate dependence of the bulk glass transition, and corrects systematic biases in the polyhedral populations predicted by widely used classical force fields. At the free surface, mass density recovers to bulk values over ~10 Å, while local coordination requires a slightly wider subsurface region to fully converge. The outermost layer is oxygen-enriched, exhibits altered polyhedral connectivity with contracted Al–O bonds, and hosts a broad population of under-coordinated motifs (notably AlO 3 and OAl 2 ) whose abundances are governed by glass stability. These under-coordinated surface motifs exhibit distinct vibrational signatures and occur as locally paired Lewis acid and Brønsted base sites consistent with bond-valence compensation, yet remain spatially dispersed rather than aggregating into extended clusters. Despite this pronounced structural heterogeneity, surface relaxation and the glass-transition temperature remain comparable to their bulk counterparts, suggesting that the disordered surface is kinetically stable once formed. Together, these results establish a molecular-level picture of amorphous alumina surfaces and demonstrate the capability of machine-learned potentials to resolve structure–property relationships in disordered oxide interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Systems Innovation: Modernization & Efficiencies for ESH&Q Reviews

Environmental compliance reviews at INL have traditionally been managed through fragmented systems, relying on multiple spreadsheets and manual processes. This inefficiency led to time-consuming status updates and redundant tasks, such as manually sending reminder emails and transferring data from Excel to the Environmental Review Process (ERP). Initial attempts to streamline these processes using Power Automate and Excel revealed significant limitations, necessitating a more comprehensive solution. To address these immediate inefficiencies, automated workflows were developed using Power Automate. These workflows were designed to send scheduled status update reminders and capture responses through standardized forms, with submitted data flowing directly into centralized Excel trackers. This automation reduced the administrative burden, improved data accuracy, and enabled faster, more consistent reporting. Specifically, email automation achieved a 65% efficiency gain, while data integration saw a 48% improvement, resulting in 91% of project statuses being updated within two months. Despite the improvements brought by Power Automate, the fragmented nature of the review processes persisted. To further enhance efficiency and accuracy, the Integrated Review Tool (IRT) was developed. The IRT aims to centralize review initiation and connect team systems, creating an interconnected data infrastructure that preserves team autonomy while enhancing overall efficiency. This tool automates email reminders, centralizes reviews, and streamlines data integration, significantly improving the accuracy and efficiency of environmental compliance reviews. The design and development of the IRT involved advanced systems methodology, process mapping, project management, and collaboration with subject matter experts. The minimum viable product design is 100% complete, and system development is currently underway, with expected outcomes including a centralized entry point for all ESH&Q reviews, automated routing, real-time tracking and analytics, AI integration, and a user-friendly interface. This project demonstrates the potential of leveraging automation and integrated systems to enhance efficiency, accuracy, and decision-making in environmental reporting and compliance processes at INL.

99 - GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

An Eulerian multimaterial framework for simulating high-explosive aquarium tests

Aquarium tests of cylindrical high-explosive charges provide optical data of the detonation front velocity and shape, propagation of the shock wave in the surrounding water, and expansion rates of the detonation products behind the front. Data from aquarium experiments is often used for calibration of reactive burn models based on phenomenological equations of state (EOS) and reaction rate laws. This paper presents a multimaterial numerical modeling framework to solve the 2D axisymmetric reactive Euler equations for high-explosive aquarium tests, in particular for ammonium nitrate - fuel oil (ANFO) explosives. An extension of the Ghost Fluid Method (GFM) is used to handle the dynamic material interfaces for the ANFO explosion products, the charge-confining material (polymethyl methacrylate PMMA), and the surrounding water. This study analyzes the sensitivity of calculations (both computational efficiency and numerical accuracy) to different algorithms for the material interface models including the original GFM versus Riemann solver-based strategies. A novel method for defining the left and right states in the interfacial Riemann problem eliminates the need for sorting or nodal interpolation during the projection along the material interface. Numerical tests indicate that populating the interface node values using the Riemann solution mitigate the overheating error observed in steady-state calculations. Solution convergence and computational efficiency are explored as a function of the spatial and temporal order of the schemes. Results from the computational model with analytical equations of state and fitted reaction rate parameters show very good quantitative agreement with experimentally observed detonation front velocity, reaction products expansion, and shock wave propagation in the surrounding water for a cylindrical ANFO charge encased in PMMA. Finally, the proposed modeling framework, in conjunction with experimental tests, provides a reliable tool to assess equations of state and reaction rate expressions for reactive burn models of confined high explosives.

42 ENGINEERING↗
DOE OSTI2021

Identifying and tracking bubbles and drops in simulations: A toolbox for obtaining sizes, lineages, and breakup and coalescence statistics

Knowledge of bubble and drop size distributions in two-phase flows is important for characterizing a wide range of phenomena, including combustor ignition, sonar communication, and cloud formation. The physical mechanisms driving the background flow also drive the time evolution of these distributions. Accurate and robust identification and tracking algorithms for the dispersed phase are necessary to reliably measure this evolution and thereby quantify the underlying mechanisms in interface-resolving flow simulations. The identification of individual bubbles and drops traditionally relies on an algorithm used to identify connected regions. This traditional algorithm can be sensitive to the presence of spurious structures. A cost-effective refinement is proposed to maximize volume accuracy while minimizing the identification of spurious bubbles and drops. An accurate identification scheme is crucial for distinguishing bubble and drop pairs with large size ratios. The identified bubbles and drops need to be tracked in time to obtain breakup and coalescence statistics that characterize the evolution of the size distribution, including breakup and coalescence frequencies, and the probability distributions of parent and child bubble and drop sizes. An algorithm based on mass conservation is proposed to construct bubble and drop lineages using simulation snapshots that are not necessarily from consecutive time steps. These lineages are then used to detect breakup and coalescence events, and obtain the desired statistics. Accurate identification of large-size-ratio bubble and drop pairs enables accurate detection of breakup and coalescence events over a large size range. Accurate detection of successive breakup and coalescence events requires that the snapshot interval be an order of magnitude smaller than the characteristic breakup and coalescence times to capture these successive events while minimizing the identification of repeated confounding events. Together, these algorithms serve as a toolbox for detailed analysis of two-phase simulations, and enable insights into the mechanisms behind bubble and drop formation and evolution in flows of practical importance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Quantifying and visualizing the microscopic degrees of freedom of grain boundaries in the Wigner–Seitz cell of the displacement-shift-complete lattice

Here we introduce a grain boundary (GB) translation vector, t ws , to describe and quantify the domain of the microscopic degrees of freedom of GBs. It has long been recognized that for fixed macroscopic degrees of freedom of a GB there exists a large multiplicity of states characterized by different relative grain translations. More recently another degree of freedom, [n], the number of GB atoms, has emerged and is now recognized as an equally important component of GB structural multiplicity. In this work, we show that all GB microstates can be uniquely characterized by their value of t ws , which is located within the Wigner–Seitz (WS) cell of the Displacement-Shift-Complete lattice (DSCL) of the GB. The GB translation vector captures information about both the translation state and the number of GB atoms. We show that the density of GB microstates inside the WS cell of the DSCL is not uniform and can form clusters that correspond to different GB phases. Further, the vectors connecting the centers of the clusters correspond to the Burgers vectors of GB phase junctions, which can be predicted without building the junctions. Using t ws , we quantify GB excess shear and argue that it is defined up to a DSCL vector, which has implications for thermodynamic equilibrium conditions. Additionally, this work generalizes the definition of the number of GB atoms [n] to asymmetric boundaries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multiphysics Degradation Modeling of Energy Storage Materials via RKPM with a Neural Network-Enhancement

In energy storage materials, strong electrochemical-mechanical coupling and highly anisotropic material properties contribute to the formation and propagation of micro-cracking during charge/discharge cycling, resulting in reduced performance and service life. A coupled electro-chemo-mechanical reproducing kernel particle method (RKPM) formulation is developed, and a patch-test is formulated to certify optimal convergence of the proposed RKPM method for the coupled physics system. With microstructural images supplied by the National Renewable Energy Laboratory (NREL), pixel-based model construction by RKPM is then used to represent the complex material microstructures for modeling the coupled physics of these systems. Further, a neural network-enhanced reproducing kernel particle method (NN-RKPM) [1, 2] is introduced to effectively model damage and crack propagation in the material microstructures; the location, orientation, and solution transition near a localization are automatically captured by superimposed block-level NN optimizations. This NN enrichment approach allows for effective modeling of localizations via a fixed background discretization, relieving tedious efforts for adaptive refinement in traditional mesh-based methods. Applications to the heterogeneous microstructures of Li-ion battery cathodes will be presented to demonstrate the effectiveness of the proposed methods. Reference: [1] Baek, J., Chen, J. S., Susuki, K., "Neural Network enhanced Reproducing Kernel Particle Method for Modeling Localizations," International Journal for Numerical Methods in Engineering, Vol. 123, pp 4422-4454, https://doi.org/10.1002/nme.7040, 2022. [2] Baek, J., Chen, J. S., "A Neural Network-Based Enrichment of Reproducing Kernel Approximation for Modeling Brittle Fracture", Computer Methods in Applied Mechanics and Engineering Vol. 410, 116590, 2024.

electro-chemo-mechanical coupling↗
DOE OSTI2024

Liquid Interfacial Electron Microscopy Identifies Nanogalvanic Corrosion in Pearlitic Steel

The nanoscale mechanisms of localized corrosion in low carbon steels have remained elusive due to the complexity of studying the degradative material behavior at nanoscale solid-liquid interfaces. We identified various steps in the nanogalvanic corrosion processes using in-situ liquid-cell scanning transmission electron microscopy (STEM) using a microfluidic holder by Hummingbird Scientific. Initial work, performed at low magnification, identified the initiation point on a 1018 low-carbon steel surface. This initiation point was determined to be a triple junction of two ferrite grains bridging a cementite grain in contact with a baseline electrolyte of 6 uM CO2 dissolved in a buffered (2.78 uM Na2SO4) aqueous solution, pH 6.1. The pre-etched low-carbon steel surface was prepared using focused ion beam lift-out procedures to extract a cross-section of the low-carbon steel surface, which then was thinned to about 150 nm and transferred to a SiN membrane microfluidic window. The transfer was made using a lift-out needle to attach the low-carbon steel lamella to the corner of the SiN window, and then Pt/C deposition held the lamella in contact with the window while it was released from the lift out needle. To identify the triple point on the low carbon steel lamella, prior to attachment on the SiN window, the sample was characterized for compositional variations with energy dispersive x-ray spectroscopy mapping, grain orientation and phase mapping with precession electron diffraction, and thickness mapping with energy filtered transmission electron microscopy. This pre-characterization prior to the in-situ experiment provided a map of the multiphase and multigrain structure, where the in-situ liquid cell imaging provided a clear understanding of the initiation point on the sample. These data were cross-correlated to paint a holistic picture of the triple junction site, enabling low electron-fluence in-situ snapshot imaging to avoid dominating the native corrosion reactions with effects from the incident electron beam. This initial result identified that localized, nanogalvanic corrosion at the phase interface was the dominant corrosion process in the low-carbon steel, so we next targeted the observation of an array of these nanogalvanic features phase boundaries in a pearlite grain. Near-surface ferrite/cementite phase interfaces that typify pearlitic low-carbon steel were extracted, pre-characterized, and imaged for the in-situ corrosion processes. The sample was a cross-section from a pearlite grain, with alternating ferrite and cementite grains that extended microns down from the pre-etched low-carbon steel pipe surface. After contact with a buffered aqueous solution, the phase boundaries between the ferrite and cementite began to dissolve, with observable material loss and thickness changes in the dark-field and bright-field STEM images. Within minutes, the corrosion front proceeded deeper into the material, claiming a thin layer of ferrite around all exposed phase boundaries before progressing laterally into the ferrite matrix, converting the ferrite to corrosion product normal to each buried cementite grain. Formation of the corrosion product causes a volumetric expansion, creating a lateral wedging force that mechanically ejects the cementite grains from their grooves and leaves behind percolation channels into the steel substructure. Rapid and deleterious, this nanogalvanic corrosion pathway represents an important target for understanding and preventing run-away degradation in this common building material. Observation of this corrosion mechanism was enabled by the combination of pre-characterization using standard structural, grain, and compositional analysis in the TEM, which provides maps for understanding the reaction propagation captured in low-dose, in-situ, liquid-cell STEM.

corrosion↗
DOE OSTI2020

Modeling of fluid injection-induced fault reactivation using coupled fluid flow and mechanical interface model

The present study is aimed at developing a numerical model to reproduce coupled hydro-mechanical processes associated with fault reactivation by fluid injection in low permeability rock, as part of the DECOVALEX-2019 project Task B. We proposed a modeling approach for simulating the processes using the TOUGH-FLAC simulator, and modeled a fault reactivation experiment conducted at Mont Terri Rock Laboratory in Switzerland. The first step of the study involved benchmark calculations considering a simplified fault plane and geometry. Fluid flow along a fault was modeled using elements of aperture-sized thickness on the basis of Darcy's law and the cubic law in TOUGH2, whereas the mechanical behavior of a single fault was represented by zero-thickness interface elements in FLAC3D upon which a slip and/or separation is allowed. A methodology to connect a TOUGH2 volume element to a FLAC3D interface element was developed for handling the hydro-mechanical interactions on the fault during fluid injection. Two different fault models for describing the evolutions of hydraulic aperture by elastic fracture opening and failure-induced aperture increase were considered in the benchmark calculations. In the coupling process, the changes in geometrical features and hydrological properties induced by mechanical deformation were continuously updated. The transient responses of the fault and host rock to stepwise pressurization were examined during the simulation. The hydro-mechanical behavior, including the injection flow rate, pressure distribution around the borehole, stress conditions, and displacements in normal and shear directions were monitored in the surrounding rock and along the fault. The results of benchmark calculations suggest that the developed model reasonably represents the hydro-mechanical behavior of a fault and the surrounding rock. This modeling approach was applied to the fault reactivation experiment of the Mont Terri Rock Laboratory. In this interpretive modeling, a parametric study was conducted to examine the effects of input parameters regarding in situ stress and fault properties on the hydro-mechanical responses of the fault to water injection. Then, an optimal parameter set to reproduce the field experiment results was chosen by trial-and-error. The injection flow rate and pressure response during fault reactivation closely matched those obtained at the site, which indicates the capability of the model to appropriately capture the progressive pathway evolution during fault reactivation tests at the site. Finally, the anchor displacements were overestimated by the model, but a fair agreement was obtained in terms of the order of magnitude and the variation tendency.

58 GEOSCIENCES↗
DOE OSTI2023

A comparative study of solute trapping in Fe-(33–45 at%) Cu alloys manufactured by laser directed energy deposition

The high cooling rates in laser directed energy deposition (DED-LB) of alloys lead to substantial amounts of solute trapping as solute atoms cannot diffuse away from the solid/liquid interface before it advances. In some concentrated alloys, this results in supersaturated solid phases that form nanoscale hierarchical microstructures when the solute atoms precipitate out during reheating from subsequent laser passes. We choose the Iron-Copper (Fe-Cu) binary alloy as model system as it is chemically homogeneous in the liquid phase and has negligible solid solubility at room temperature. Two alloys with nominal compositions in atomic (at.) %, Fe67Cu33 and Fe55Cu45, were manufactured using DED-LB. Scanning transmission electron microscopy (STEM), energy dispersive spectroscopy (EDS) and wavelength dispersive spectroscopy (WDS) were used to characterize the nanostructures and heterogeneous chemical compositions. A non-equilibrium solute partitioning model was used to compute the supersaturated chemistries of the constituent phases and validated with experimentally measured compositions. The measured phase compositions of the two alloys were very similar, at roughly 12 at.% Cu and 4 at.% Fe in the α(bcc)-Fe and ε(fcc)-Cu phases respectively, despite having different processing parameters and mechanical behavior. This indicates that the total thermal history, that depends on both the processing parameters and laser scan pattern, plays a stronger role on the final microstructure evolution than just the initial quantity of trapped solute. In addition, we find that current non-equilibrium solute partitioning models applied on the continuum scale fall short of predicting accurate quantitative phase compositions in concentrated alloys, although the qualitative trends are captured correctly.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The importance of explicitly representing the streambed in watershed models

Abstract The streambed is the critical interface between the aquatic and terrestrial systems and hosts important biogeochemical hot spots within river corridors. Although the streambed characteristics are significantly different from those of its surrounding soil, the streambed itself has not been explicitly represented in watershed models. Here, we explicitly incorporated a streambed layer into an integrated hydrologic model through model parameterization and discretization. We examined the hydrological effects of streambed characteristics, including hydraulic conductivity ( K ), layer thickness, and resolution, on the exchange fluxes across the streambed as well as the streamflow at the watershed outlet. The numerical experiments were performed in the American River Watershed, a headwater, mountainous watershed within the Yakima River Basin in central Washington. Despite having a negligible effect on the watershed streamflow, an explicit representation of the streambed with distinctive properties dramatically changed the magnitude and variability of the exchange flux. In general, a larger streambed K along with a thicker streambed layer induced larger exchange fluxes. The exchange flux was most sensitive to the streambed resolution. A finer streambed resolution increased exchange fluxes per unit area while reducing the overall exchange volumes across the entire streambed. The amount of baseflow decreased by 6% as the streambed resolution increased from 250 to 50 m. This finding is important because these hydrological changes may, in turn, affect the exchange of nutrients and contaminants between surface water and groundwater and the associated biogeochemical processes. Our work demonstrated the importance of representing streambeds in fully distributed, process‐based watershed models to better capture the exchange flow dynamics in river corridors.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Process Modeling of CO 2 Absorption with Monoethanolamine Aqueous Solutions Using Rotating Packed Beds

A first-principle process simulation model is presented for the chemical absorption of carbon dioxide (CO 2 ) with monoethanolamine (MEA) aqueous solutions using rotating packed beds (RPB). Built on a proven rate-based packed bed absorber model, the RPB model rigorously simulates the phase and chemical equilibria at the vapor-liquid interface, the heat and mass transfer across the gas and liquid films, the fast reactions between MEA and CO 2 in the liquid film, and the RPB hydraulics. Here, estimation of the mass transfer rate across the liquid film is central to accurate simulation of the CO 2 absorption process with MEA aqueous solutions. We show that the literature lab-scale RPB data for CO 2 removal efficiency can be satisfactorily correlated by introducing a correction factor for the effective packing surface area predicted by the Onda correlation. Given the validated RPB model, we further show that, among the gas-phase mass transfer coefficient, the liquid-phase mass transfer coefficient, and the reaction rate constant for the reaction between amine and CO 2 , the reaction rate constant is the controlling step with the highest potential to enhance the CO 2 absorption performance in RPB.

42 ENGINEERING↗
DOE OSTI2024

Fluidized-Bed Gasification of Coal-Biomass-Plastics for Hydrogen Production

Coal is one of the most abundant fossil energy resources in the United States and in the world. The recoverable reserves in the United States are estimated to be about 252 billion tons – more than 350 years of supply at current rates of usage. However, the share of coal in total primary energy consumption in the US has been declining over the years. The decline of coal is mainly attributed to cheap natural gas and precipitous declines in the cost of electricity production from renewable technologies such as wind and solar. Coal can potentially be used if it is coupled with carbon-neutral feedstock such as biomass-agricultural residues, forest biomass, and forest residues. Co-gasification of coal and biomass can become a negative carbon emission technology if the carbon dioxide (CO 2 ) is captured and sequestered. Although the biomass gasification process has a lot of similarities to coal gasification, the large-scale adaptation of power production sourced from biomass has not come to fruition. The main reason is that the power production from biomass is still expensive when compared with natural gas or coal power technologies. To address the feedstock cost, one approach is to use low-cost feedstocks, such as municipal solid wastes (MSW) or plastics, for gasification. Gasification involves the partial oxidation of coal and/or biomass feedstocks to produce a combustible fuel called synthesis gas (syngas) which is composed of carbon monoxide (CO), hydrogen (H 2 ), CO 2 , methane (CH 4 ), nitrogen (N 2 ), water (H 2 O), and other compounds that might be considered as contaminants. Raw syngas from gasification must go through multiple steps to produce high-purity hydrogen. The specific steps depend upon the quality (gas composition, contaminants, and their concentration) and condition (pressure and temperature) of syngas. The long-term goal of the project was to utilize coal and plastics together with biomass to produce energy and fuels using a gasification platform while reducing greenhouse gas emissions. The main objective of this research was to examine gasification performance in a laboratory-scale fluidized-bed gasifier for hydrogen production. The specific objectives of the research were to: (i) study coal-plastic-biomass mixture flowability for consistent feeding in the gasifier; (ii) understand the gasification behavior of the mixture in steam and oxygen environments; (iii) perform thermal property characterization of ash and slag from the mixture feedstock and refractory-ash interface of the mixture under gasification conditions; and (iv) develop process models to determine the technology needed for syngas cleanup and contaminants. The study found that there was no apparent segregation when biomass, coal, and waste plastics were mixed together during feeding. Although there were differences in hydrogen production when individual feedstock were fed, the hydrogen concentration remained almost constant with various blends. Therefore, blending waste plastics with biomass and coal, which are all abundant, is a better approach for energy production. Results of the techno-economic analysis suggested that integration of advanced gasification (GTI’s R-GAS™) and syngas cleanup and conditioning technologies (RTI’s WDP and AFWGS) for clean hydrogen production resulted in substantial benefits, including significant capital cost and operating cost reductions. Advanced technologies resulted in 16% reduction in the hydrogen production cost (COH) from 2.94 $\$$/kg to 2.47 $\$$/g, with further scope for optimization and cost reduction. These advanced technologies also result in lower emissions, and improved energy efficiency.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Predictive Tools for Customizing Heat Treatment of Additively Manufactured Aerospace Components

Laser-bed powder fusion (LBPF) additive manufacturing is increasingly being used to produce components of complex geometries using the Ni-base superalloy Inconel 718. The composition and the microstructure of the alloy are currently well optimized for wrought components made using conventional manufacturing processes such as rolling, forging, extrusion, etc. The attractive mechanical properties of the alloy result from the underlying austenitic matrix with fine equiaxed grains, and a high density and uniform distribution of the precipitation hardening phase, γ". Heat treatment steps such as homogenization, solutioning and aging are well documented for the wrought alloy. However, when the same wrought alloy compositions are used for the additive manufacturing (AM) processes, the asprocessed microstructure is significantly different, because of the different thermal history associated with LBPF, including rapid solidification and multiple temperature excursions that lead to multiple re-melting and reheating in the solid state. Rapid solidification introduces potential non-equilibrium effects at the moving solid-liquid interfaces that impact the extent of solute segregation, as well as the morphology of the dendritic grains that form. In order to recover the target mechanical properties, AM components have to undergo post-process heat treatments. However, such heat treatments have to be custom designed for the AM process and the component geometry because of the expected vast differences in the microstructure at various locations of a component with complex geometry. The homogenization and precipitation steps should be optimized for the component so that target mechanical properties can be obtained throughout the part. The objective of this research is to utilize High Performance Computing in phase field simulations of microstructure evolution during post-processing of AM components. The physics-based modeling will be beneficial in reducing the experimental effort required for heat treatment process selection, optimization, and certification, thus leading to a significant reduction in energy consumption for AM and post-processing heat treatment. The optimization study will help identify heat treatments steps that are critical for development of a final desired microstructure with the minimum energy input. This combined with shortening of the production cycle (time-to-market) by reducing the number of failed parts (property targets), and reduction in the number of iterations for process optimization, will enable 30-40% savings in the energy costs. Phase field simulations of the degree of homogenization and the effect of local matrix composition on the nucleation and growth of competing precipitating phases were performed using the Microstructure Evolution Using Massively Parallel Phase Field Simulations code developed in-house at the Oak Ridge National Laboratory. The simulations were able to successfully capture the kinetics of nucleation and growth, and morphologies of various precipitating phases as a function of local matrix compositions and composition gradients characteristic of local microstructures arising from location-dependent variations in the thermal conditions. Future work will involve extending the simulations to a length scale consisting of multiple dendrites, so that the effect of homogenization on the coarsening of the dendrites can be simulated and used as an additional input to the optimization of the heat treatment process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Materials Challenges and Opportunities for Energy Generation, Conversion, Delivery, and Storage (Applied Energy Tri-Laboratory Consortium Workshop Report)

This report documents the outcomes of the Tri-Laboratory Materials Workshop that was held July 31 and August 1, 2019 to begin addressing the needs, opportunities, and challenges associated with the development, fabrication, and testing of the needed materials and components for integrated hybrid energy systems (i.e., incorporating nuclear, fossil, and renewables for electric and thermal applications). This was accomplished by assembling the research program leads and principal investigators at Idaho National Laboratory (INL), National Energy Technology Laboratory (NETL), and National Renewable Energy Laboratory (NREL), who support the research and development of new technology and system integration. The team then identified and prioritized key materials development needs. This effort was intended to enhance communications and synergy among the Tri-Lab partners. Advanced functional and structural materials are central to transformative energy technologies for energy generation, conversion, delivery, and storage. With that in mind, the workshop focused on identifying and assessing the foundational materials research needs at both the basic and applied levels. Materials challenges include the ability to withstand harsh environments, such as high temperatures and pressures, corrosion, oxidation, or irradiation while maintaining flexible mission profiles and long service lifespans. Advanced energy system material challenges and needs range from materials for the capture, upgrading/concentration, storage, and delivery of low-grade heat to materials for high temperature environments that involve liquid metals, molten salt, and very high temperature gas heat delivery and storage systems. Material improvements are needed for hybrid energy systems due to accelerated corrosion and stress-fatigue failure of materials and equipment, which results from increased frequency and amplitude of thermal, mechanical, and electrical cycling of systems components. Multifunctional materials are needed for high temperature solid-oxide fuel cells, advanced electrochemical reactors, and in-process separation. Relative to materials manufacturing, application of advanced additive and subtractive methods need to be understood to develop both thin-layer homogenous materials and materials of graded composition. Materials modeling and machine learning will be critical to accelerate the design and production of power electronics, and nuclear reactor materials and fuel, as well as to gain an understanding of beneficial materials phenomena or deleterious microstructure evolution. There is also a need for standardized models, computational structures, data reporting protocols and modeling tools across the three laboratories. This would allow consistent results, analysis, and data sharing. Combining computational capabilities between the three laboratories (e.g., hardware, software) would greatly increase computational capabilities and throughput. The workshop identified the need for laboratories to anticipate and address problems that will occur during scale-up. Laboratory work must connect with industry to ensure that research focuses on processes that are scalable and marketable. Industry input and perspective are essential to guide laboratory research to meet these requirements and deploy new technology in industrial demonstrations. Another aspect of scale-up is the integration of multiple systems since new challenges often arise at the subsystem interfaces. Establishing a scale-up manufacturing demonstration/pilot plant, potentially as an industrial user facility, would be beneficial to the laboratories and industry. That modular scale-up manufacturing demonstration/pilot plant would allow researchers to find and resolve interface problems that cannot be identified by focusing only on individual parts. Communication exchanges among the organizers, attendees, and workshop survey responses indicate that the workshop was successful in achieving its goal to identify key technology gaps and research needs. Strong positive feedback was received on the sharing of ideas, capabilities, talent, and passion to move forward on the materials-related action items.

36 MATERIALS SCIENCE↗