AERODYNAMIC CHARACTERISTICS IN GROUND EFFECT OF A LARGE-SCALE MODEL WITH A HIGH DISK-LOADING LIFTING FAN MOUNTED IN THE FUSELAGE
Aerodynamic characteristics in ground effect of a large scale model
AERODYNAMIC CHARACTERISTICS↗
SEARCH · Engineering Papers
Results for “high loading”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Helicopter rotor rotational noise predictions based on measured high-frequency blade loads
In tests conducted at the Langley helicopter rotor test facility, simultaneous measurements of up to 200 harmonics of the fluctuating aerodynamic blade surface pressures and far-field radiated noise were made on a full-scale nontranslating rotor system. After their characteristics were determined, the measured blade surface pressures were converted to loading coefficients and used in an existing theory to predict the far-field rotational noise. A comparison of the calculated and measured noise shows generally good agreement up to 300 to 600 Hz, depending on the discreteness of the loading spectrum. Specific attention is given to the effects of the blade loading coefficients, chordwise loading distributions, blade loading phases, and observer azimuthal position on the calculations.
Hosier, R. N.↗
An elastic-plastic analysis of fatigue crack closure in modes I and II
In this paper, an efficient elastic-plastic finite element procedure to analyze crack-closure and, its effects on fatigue crack growth under general spectrum loading, is presented. A hybrid-displacement finite element procedure is used to properly treat the stress and strain singularities near the crack-tip; and crack-growth under cyclic loading is simulated by the translation of certain 'core' elements, near the crack-tip, in which proper stress and strain singularities were embedded. Both pure mode I and mode II types of cyclic loading are considered. In the mode I case, four types of cyclic loading, viz., constant amplitude block loading, high-to-low block loading, low-to-high block, and a single overload in an otherwise constant amplitude block loading are considered; whereas in mode II, only a constant amplitude block loading is considered. Detailed results are presented for the crack-closure and opening-stresses, crack-surface deformation profiles, etc., in each case. Certain observations, based on the present numerical results, concerning various factors that cause crack growth acceleration or retardation under general spectrum loading, are presented and discussed.
Nakagaki, M.↗
H-P adaptive methods for finite element analysis of aerothermal loads in high-speed flows
The commitment to develop the National Aerospace Plane and Maneuvering Reentry Vehicles has generated resurgent interest in the technology required to design structures for hypersonic flight. The principal objective of this research and development effort has been to formulate and implement a new class of computational methodologies for accurately predicting fine scale phenomena associated with this class of problems. The initial focus of this effort was to develop optimal h-refinement and p-enrichment adaptive finite element methods which utilize a-posteriori estimates of the local errors to drive the adaptive methodology. Over the past year this work has specifically focused on two issues which are related to overall performance of a flow solver. These issues include the formulation and implementation (in two dimensions) of an implicit/explicit flow solver compatible with the hp-adaptive methodology, and the design and implementation of computational algorithm for automatically selecting optimal directions in which to enrich the mesh. These concepts and algorithms have been implemented in a two-dimensional finite element code and used to solve three hypersonic flow benchmark problems (Holden Mach 14.1, Edney shock on shock interaction Mach 8.03, and the viscous backstep Mach 4.08).
Chang, H. J.↗
High-speed Landing Loads Measured on the Douglas X-3 Research Airplane
Explore the source record for details and available documents.
Marcy, William L↗
Microgravity Production of Nanoparticles of Novel Materials Using Plasma Synthesis
The research goal is to study the formation in reduced gravity of high quality nanoparticulate of novel materials using plasma synthesis. Particular emphasis will be placed on the production of powders of non-oxide materials like diamond, SiC, SiN, c-BN, etc. The objective of the study is to investigate the effect of gravity on plasma synthesis of these materials, and to determine how the microgravity synthesis can improve the quality and yield of the nanoparticles. It is expected that the reduced gravity will aid in the understanding of the controlling mechanisms of plasma synthesis, and will increase the yield, and quality of the synthesized powder. These materials have properties of interest in several industrial applications, such as high temperature load bearings or high speed metal machining. Furthermore, because of the nano-meter size of the particulate produced in this process, they have specific application in the fabrication of MEMS based combustion systems, and in the development and growth of nano-systems and nano-structures of these materials. These are rapidly advancing research areas, and there is a great need for high quality nanoparticles of different materials. One of the primary systems of interest in the project will be gas-phase synthesis of nanopowder of non-oxide materials.
Frenklach, Michael↗
Characterization of Composites Response at High Rates of Loading
The objective of the proposed research is to experimentally study the effect of strain rate on mechanical response (deformation and failure) carbon fiber/epoxy matrix composites. The experimental data provide the information needed for the development of a nonlinear, rate dependent deformation and strength models that can subsequently be used in design. This year effort was directed into testing the epoxy resin. Two types of epoxy were tested each in tension and shear at various strain rate that ranges from 5x10(exp -5), to 700/s. The results show that both the strain rate and the mode of loading affect the epoxy response.
Gilat, Amos↗
Aerodynamic Characteristics of a Large-Scale Model with a High Disk-Loading Lifting Fan Mounted in the Fuselage
An investigation was conducted to determine the longitudinal characteristics during low-speed flight of a large-scale VTOL airplane model with a direct lifting fan enclosed in the fuselage. The model had a shoulder-mounted unswept wing of aspect ratio 5. The effect on longitudinal characteristics of fan operation, propulsion by means of deflecting the fan efflux, trailing-edge flap deflection, and horizontal-tail height were studied.
Aoyagi, Kiyoshi↗
Crack Growth Behavior in the Threshold Region for High Cycle Fatigue Loading
This presentation describes results obtained from a research project conducted at the NASA Johnson Space Center (JSC) that was jointly supported by the FAA Technical Center and JSC. The JSC effort was part of a multi-task FAA program involving several U.S. laboratories and initiated for the purpose of developing enhanced analysis tools to assess damage tolerance of rotorcraft and aircraft propeller systems. The research results to be covered in this presentation include a new understanding of the behavior of fatigue crack growth in the threshold region. This behavior is important for structural life analysis of aircraft propeller systems and certain rotorcraft structural components (e.g., the mast). These components are often designed to not allow fatigue crack propagation to exceed an experimentally determined fatigue crack growth threshold value. During the FAA review meetings for the program, disagreements occurred between the researchers regarding the observed fanning (spread between the da/dN curves of constant R) in the threshold region at low stress ratios, R. Some participants believed that the fanning was a result of the ASTM load shedding test method for threshold testing, and thus did not represent the true characteristics of the material. If the fanning portion of the threshold value is deleted or not included in a life analysis, a significant penalty in the calculated life and design of the component would occur. The crack growth threshold behavior was previously studied and reported by several research investigators in the time period: 1970-1980. Those investigators used electron microscopes to view the crack morphology of the fatigue fracture surfaces. Their results showed that just before reaching threshold, the crack morphology often changed from a striated to a faceted or cleavage-like morphology. This change was reported to have been caused by particular dislocation properties of the material. Based on the results of these early investigations, a program was initiated at JSC to repeat these examinations on a number of aircraft structural alloys that were currently being tested for obtaining fatigue crack growth properties. These new scanning electron microscope (SEM) examinations of the fatigue fracture faces confirmed the change in crack morphology in the threshold crack tip region. In addition, SEM examinations were further performed in the threshold crack-tip region before breaking the specimens open (not done in the earlier published studies). In these examinations, extensive crack forking and even 90-degree crack bifurcations were found to have occurred in the final threshold crack-tip region. The forking and bifurcations caused numerous closure points to occur that prevented full crack closure in the threshold region, and thus were the cause of the fanning at low-R values. Therefore, we have shown that the fanning behavior was caused by intrinsic dislocation properties of the different alloy materials and were not the result of a plastic wake that remains from the load-shedding test phase. Also, to accommodate the use of da/dN data which includes fanning at low R-values, an updated fanning factor term has been developed and will be implemented into the NASGRO fatigue crack growth software. The term can be set to zero if it is desired that the fanning behavior is not be modeled for particular cases, such as when fanning is not a result of the intrinsic properties of a material.
Forman, Royce G.↗
Evaluation of LS-DYNA MAT162 for Modeling Composite Fastener Joints for High Rates of Loading
In the present work, the behavior of composite-fastener joints in bearing failure at dynamic stroke rates of 500 in/s, 300 in/s and 100 in/s has been evaluated through progressive damage analysis (PDA) material model in LS-DYNA, namely MAT162. Two joint types: titanium pin and Hi-Lok® fastener were analyzed to identify the differences between without and with preload conditions. A meso-level approach where each lamina was modeled separately was employed and a contact definition based on fracture toughness data was defined to represent composite delamination behavior. Test fixture had been modeled in a detailed manner to account for the dynamic effects and the simulation results were validated against experimental data. Preliminary test-analysis correlation indicated that MAT162 predicted results conservatively when compared to tests. Debris accumulation were observed to greatly affect the test results which were not considered in the current modelling strategies.
Kona, A.↗
Tensile-strength apparatus applies high strain-rate loading with minimum shock
Tensile-strength testing apparatus employs a capillary bundle through which a noncompressible fluid is extruded and a quick-release valve system. This apparatus applies the test loads at relatively constant very high strain rates with minimal shock and vibration to the tensile specimen and apparatus.
Cotrill, H. E., Jr.↗
Intermountain West Wildland Fires: Mapping Tree Mortality and Burn Patches using NASA Earth Observations to Determine Fire Risk and Inform Fire Management Practices
Within the intermountain west, monitoring fuel loads is a major concern for wildland fire management efforts. To address this concern, we partnered with the U.S. Forest Service to inform the agency which forested areas should be prioritized for prescribed burning and fuel reduction near human communities in the Bridger-Teton National Forest, Wyoming. We created burn maps, fuel load maps, and a tutorial document to identify forest impact trends and provide the partner with the tools to replicate project methods for expansion to other wildfire crisis strategy sites. These end products were made using two NASA Earth observations: Landsat 8 Operational Land Imager and Shuttle Radar Topography Mission. Based on our random forest analysis, our maps identified 998 acres within the Wildland Urban Interface that are predicted to have high fuel loading and high burn severity within the Bridger-Teton National Forest. Forested areas closer to heavily populated areas such as Jackson, Kelly, Moran, New Forks Lake, and Star Valley Ranch should be prioritized for fuel reduction. However, our random forest model analysis was limited to using vegetation and topographical indices with no field data for model validation. Therefore, future studies should use field data for model validation to improve model accuracy and additionally incorporate Global Ecosystem Dynamics Investigation data into models to create better predictions of forested areas with high fuel load and high burn severity.
Remote Sensing↗
Multifunctional Structures for High-Energy Lightweight Load-Bearing Storage
This is a pull-up banner of the Multifunctional Structures for High-Energy Lightweight Load-bearing Storage (M-SHELLS) technology that will be on display at the SciTech Conference in January 2018. Efforts in Multifunctional Structures for High Energy Load-Bearing Storage (M-Shells) are pushing the boundaries of development for hybrid electric propulsion for future commercial aeronautical transport. The M-Shells hybrid material would serve as the power/energy storage of the vehicle and provide structural integrity, freeing up usable volume and mass typically occupied by bulky batteries. The ultimate goal is to demonstrate a system-level mass savings with a multifunctional structure with energy storage.
Loyselle, Patricia L.↗
Experiments investigating advanced materials under thermomechanical loading
Many high temperature aircraft and rocket engine components experience large mechanical loads as well as severe thermal gradients and transients. These nonisothermal conditions are often large enough to cause inelastic deformations, which are the ultimate cause for failure in those parts. A way to alleviate this problem is through improved engine designs based on better predictions of thermomechanical material behavior. To address this concern, an experimental effort was recently initiated within the Hot Section Technology (HOST) program at Lewis. As part of this effort, two new test systems were added to the Fatigue and Structures Lab., which allowed thermomechanical tests to be conducted under closely controlled conditions. These systems are now being used for thermomechanical testing for the Space Station Receiver program, and will be used to support development of metal matrix composites.
Bartolotta, Paul A.↗
Some important aspects in testing high-modulus fiber composite tubes designed for multiaxial loading
Tubular specimens were potted in metal grips to determine the feasibility of this gripping method in applying multiaxial loads. Strain gage rosettes were used to assess grip transitional strains, through thickness strain variation and strain variations along the tube length and circumference. The investigation was limited to loading 0 deg, + or - 45 deg, and 90 deg graphite/epoxy and glass/epoxy tubes in axial tension. Results include modifications made to the grips to reduce transitional strains, illustrations of the tube failure modes, and some material properties. The gripping concept shows promise as a satisfactory technique for applying multiaxial loads to high strength, high modulus fiber composite tubes.
Sullivan, T. L.↗
The effect of load sequence on the statistical fatigue of composites
A theoretical model to predict the effect of loading sequence on the statistical distributions of the fatigue life and the residual strength under n-stress levels of cyclic loading is derived on the basis of a three-parameter model. In particular, the dual stress fatigue cumulative damage is studied, showing that the Miner's sum (the cumulative damage sum at fatigue failure) is a statistical variable. It is proved theoretically that the Miner's sum is always greater than or equal to unity for the high-low load sequence, while it is always smaller than or equal to unity for the low-high load sequence, with the deviation from unity increasing as the difference between the high and the low stress levels increases. An experimental test program using graphite/epoxy angle-ply laminates, carried out to generate statistically meaningful data for verifying the proposed model, is discussed.
Yang, J. N.↗
Aerodynamic Loads on Tails at High Angles of Attack and Sideslip
Results are presented for the loads and moments acting on the individual tail surfaces of a body-tail combination over a wide range of angles of attack and sideslip. The effects of forebody length and panel-panel interference on the characteristics are included. It is shown that large nonlinear variations in these loads and moments, which occur at some combinations of angle of attack and sideslip, cannot be predicted by low-angle theory. A relatively simple, but general, theoretical method for calculating these load and moment characteristics is described, and the results from this method are found to be in good agreement with experiment provided the initial positions of the forebody vortices are known. It is shown that a simple application of slender-body theory can be used to predict the side loads due to sideslip that are contributed by a vertical tail on a wide variety of wing-body-tail combinations at low angles of attack. For several configurations, changes are indicated which reduced the vertical-tail loads per unit yawing moment of each complete configuration at large angles of attack. Some results are presented on the effect of high angle of attack on the induced-flow field and tail loads due to a wing at supersonic speed.
SLENDER BODY↗
Evaluation of SAGE II and Balloon-Borne Stratospheric Aerosol Measurements: Evaluation of Aerosol Measurements from SAGE II, HALOE, and Balloonborne Optical Particle Counters
Stratospheric aerosol measurements from the University of Wyoming balloonborne optical particle counters (OPCs), the Stratospheric Aerosol and Gas Experiment (SAGE) II, and the Halogen Occultation Experiment (HALOE) were compared in the period 1982-2000, when measurements were available. The OPCs measure aerosol size distributions, and HALOE multiwavelength (2.45-5.26 micrometers) extinction measurements can be used to retrieve aerosol size distributions. Aerosol extinctions at the SAGE II wavelengths (0.386-1.02 micrometers) were computed from these size distributions and compared to SAGE II measurements. In addition, surface areas derived from all three experiments were compared. While the overall impression from these results is encouraging, the agreement can change with latitude, altitude, time, and parameter. In the broadest sense, these comparisons fall into two categories: high aerosol loading (volcanic periods) and low aerosol loading (background periods and altitudes above 25 km). When the aerosol amount was low, SAGE II and HALOE extinctions were higher than the OPC estimates, while the SAGE II surface areas were lower than HALOE and the OPCS. Under high loading conditions all three instruments mutually agree to within 50%.
Hervig, Mark↗