SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Series of transducers with seven different configurations enable measurement of forces and displacements in heart wall. New transducers small, cause minimal perturbation of heart function and attached and detached without causing excessive tissue damage. All units implanted or removed during single heartbeat, permitting rapid relocation for detail mapping.
Eight flights of the Kuiper Airborne Observatory (KAO) were devoted to solar observation. The successful observation of a total solar eclipse was accomplished. The observations were made simultaneously at 30, 50, 100, and 200 microns. The successful adaptation of the KAO for solar observations thus provided the most detailed data to date in this spectral band. The results from a preliminary analysis of the KAO data are summarized: (1) the 200 micron limb is extended about 3 arc sec above the 30 micron limb, indicating the prescence of cool dense material up to the altitudes of spicules; (2) strong radial darkening of the quiet sun intensity profile appeared at 200 microns, probably an indication that hot material in the low chromosphere is recessed into vertical magnetic flux tubes embedded in a cooler nonmagnetic substrate, which obscures the heated material approaching the limb; (3) active regions were observed to undergo a strong increase in contrast above the quiet sun background at wave lengths of 100 microns and longer; and (4) the moon was mapped for use as a photometric standard for determining the absolute intensity of the sun in all four wavelength bands.
Differential radar interferometry uses data from synthetic-aperture radar (SAR). Three passes of SAR yield three amplitude-and-phase images, from which two interferograms (phase-difference images) made. Interferograms used to make third, "double-difference" interferogram indicating vertical motion of terrain between passes. Vertical earthquake motions as small as 1 cm detectable. Used to make extensive, accurate maps of such geophysical phenomena as heaving and buckling in fault zones, motions to tectonic plates, residual displacements from earthquakes, motions from prevolcanic swelling, motions of glaciers, tides, and thermal expansion of mountains from diurnal heating.
A thermal math model for the Space Shuttle Reinforced Carbon-Carbon (RCC) Plug Repair was developed to increase the confidence in the repair entry performance and provide a real-time mission support tool. The thermal response of the plug cover plate, local RCC, and metallic attach hardware can be assessed with this model for any location on the wing leading edge. The geometry and spatial location of the thermal mesh also matches the structural mesh which allows for the direct mapping of temperature loads and computation of the thermoelastic stresses. The thermal model was correlated to a full scale plug repair radiant test. To utilize the thermal model for flight analyses, accurate predictions of protuberance heating were required. Wind tunnel testing was performed at CUBRC to characterize the heat flux in both the radial and angular directions. Due to the complexity of the implementation of the protuberance heating, an intermediate program was developed to output the heating per nodal location for all OML surfaces in SINDA format. Three Design Reference Cases (DRC) were evaluated with the correlated plug thermal math model to bound the environments which the plug repair would potentially be used.
Maps of crustal thickness derived from NASA's Gravity Recovery and Interior Laboratory (GRAIL) mission revealed more large impact basins on the nearside hemisphere of the Moon than on its farside. The enrichment in heat-producing elements and prolonged volcanic activity on the lunar nearside hemisphere indicate that the temperature of the nearside crust and upper mantle was hotter than that of the farside at the time of basin formation. Using the iSALE-2D hydrocode to model impact basin formation, we found that impacts on the hotter nearside would have formed basins up to two times larger than similar impacts on the cooler farside hemisphere. The size distribution of lunar impact basins is thus not representative of the earliest inner Solar system impact bombardment.
Maps of crustal thickness derived from NASA's Gravity Recovery and Interior Laboratory (GRAIL) mission revealed more large impact basins on the nearside hemisphere of the Moon than on its farside. The enrichment in heat-producing elements and prolonged volcanic activity on the lunar nearside hemisphere indicate that the temperature of the nearside crust and uppermantle was hotter than that of the farside at the time of basin formation. Using the iSALE-2D hydrocode to model impact basin formation, we found that impacts on the hotter nearside would have formed basins up to two times larger than similar impacts on the cooler farside hemisphere. The size distribution of lunar impact basins is thus not representative of the earliest inner Solar system impact bombardment
Asymmetry is required by most numerical simulations of stellar core-collapse explosions, but the form it takes differs significantly among models. The spatial distribution of radioactive 44Ti, synthesized in an exploding star near the boundary between material falling back onto the collapsing core and that ejected into the surroundingmedium1, directly probes the explosion asymmetries. Cassiopeia A is a young2, nearby3, core-collapse4 remnant from which 44Ti emission has previously been detected5-8 but not imaged. Asymmetries in the explosion have been indirectly inferred from a high ratio of observed 44Ti emission to estimated 56Ni emission9, from optical light echoes10, and from jet-like features seen in the X-ray11 and optical12 ejecta. Here we report spatial maps and spectral properties of the 44Ti in Cassiopeia A. This may explain the unexpected lack of correlation between the 44Ti and iron X-ray emission, the latter being visible only in shock-heated material. The observed spatial distribution rules out symmetric explosions even with a high level of convective mixing, as well as highly asymmetric bipolar explosions resulting from a fast-rotating progenitor. Instead, these observations provide strong evidence for the development of low-mode convective instabilities in core-collapse supernovae.
The considered region comprises 81% of the surface of Mars. Thermal inertia I is a composite surface property, which is equal to the square root of the product of three factors, including the thermal conductivity, the density, and the specific heat. I is the sole thermal parameter which governs the temperature variation of a periodically heated homogeneous surface, and, as such, is the prime intermediary between remote temperature observations and their geologic interpretation. The values for the thermal inertia found imply particulate surface materials. The variation in Martian surface thermal conductivity is about two orders of magnitude. Three large regions of low-inertia material are defined. Low-inertia material always possesses high albedo. There is a general tendency for higher-thermal-inertia surfaces to be darker but exceptions occur which may be related to a thin mantling of light dust or bonding of light material.
The well-known starburst in M82 at 10.8, 19.2, and 30 microns has been mapped. Scans along the galactic plane which are derived from these data reveal marked color variations with position. These color variations are correlated with the UV energy density in a manner explicable in terms of a heated mixture of dust grains extending to very small sizes. Many of the small grains may have been destroyed in the most intense regions of the starburst, but they have survived in a halo where the UV energy density is too low to destroy them but still high enough to significantly heat them. Implications of the results for interpreting IR continuum emission from starburst galaxies are considered.
A 0.02-scale model of a lifting-body concept for possible application to the Assured Crew Return Vehicle from Space Station Freedom was tested at Mach 6 and 10 in air. Thermal mappings and surface streamline patterns were obtained at angles of attack ranging from 0 to 30 deg and unit Reynolds numbers Re from 2 to 8 x 10 to the 6th/ft. Areas that experienced the highest heating were near the model nose and tip-fin leading edges. The effect of Re on windward centerline heating coefficients was negligible, whereas increases in angles of attack produced increases in heating. At Mach 6 and the highest unit Re, turbulent heat at the windward centerline was three to four times the laminar level. Leeward crossflow separation and vortex reattachment along the centerline are evident across the Re and angle-of-attack ranges tested, indicative of a complex flowfield.
We have analyzed 50 ten-day cycles of TOPEX/POSEIDON (T/P) altimeter data to evaluate the ocean dynamic topography and its temporal variations. We have employed data from both the U.S. and French altimeters along with the NASA precision orbits in this analysis. Errors in the diurnal and semidiurnal components of the Cartwright-Ray tide model have been significantly reduced using a correction developed from a combination of JGM-2 and OSU91A was employed, as well as a geoid model based solely on OSU91A. The long wavelengths of the comparisons to historical data, although geoid error still corrupts the dynamic topography for wavelengths shorter than 2500 km. The root mean square (RMS) variability is similar to previous results from Geosat, with bakground 'noise' approaching 3 cm RMS. The computed annual and semiannual variations are also similar to previous Geosat results, although the hemispheric distribution of the annual heating cycle is much better presented in the T/P results. They also compare reasonably well with the Levitus hydrographic compilation in the northern hemisphere, although the T/P variations generally have larger amplitudes. Ten-day average maps of variations in sea level compare well with simulations measurements at ocean tide gauges, with RMS differences of less than 4 cm and correlations greater than 0.6 for most of the island gauges. Time-longitude plots of these sea level variations at different latitudes in the Pacific clearly show the presence of equatorial Kelvin waves and Rossby waves, with the wave speeds agreeing well with theoretical and observed values. Measurement of variations in global sea level over cycles 2-51 have an RMS variability of 6.3 mm and a rate of change of -3.5 +/- 8 mm/yr, the uncertainty primarily due to insufficient averaging of the interannual and periodic sea level variations. These results show that the accuracy of the T/P measurements of sea level has dramatically improved over previous missions, with estimated time variable errors of 4 cm or less. Although geographically correlated orbit errors have also been reduced to the few centimeter level, further improvement in determinations of the mean dynamic topography will be difficult to obtain until a more accurate model of the marine geoid is available.
The thrust capability of turbojet cycles is reduced at high flight Mach number (3+) by the increase in inlet stagnation temperature. The 'hot section' temperature limit imposed by materials technology sets the maximum heat addition and, hence, sets the maximum flight Mach number of the operating envelope. Compressor pre-cooling, either via a heat exchanger or mass-injection, has been suggested as a means to reduce compressor inlet temperature and increase mass flow capability, thereby increasing thrust. To date, however, no research has looked at compressor cooling (i.e., using a compressor both to perform work on the gas path air and extract heat from it simultaneously). We wish to assess the feasibility of this novel concept for use in low-to-high Mach number flight. The results to-date show that an axial compressor with cooling: (1) relieves choking in rear stages (hence opening up operability), (2) yields higher-pressure ratio and (3) yields higher efficiency for a given corrected speed and mass flow. The performance benefit is driven: (i) at the blade passage level, by a decrease in the total pressure reduction coefficient and an increase in the flow turning; and (ii) by the reduction in temperature that results in less work required for a given pressure ratio. The latter is a thermodynamic effect. As an example, calculations were performed for an eight-stage compressor with an adiabatic design pressure ratio of 5. By defining non-dimensional cooling as the percentage of compressor inlet stagnation enthalpy removed by a heat sink, the model shows that a non-dimensional cooling of percent in each blade row of the first two stages can increase the compressor pressure ratio by as much as 10-20 percent. Maximum corrected mass flow at a given corrected speed may increase by as much as 5 percent. In addition, efficiency may increase by as much as 5 points. A framework for characterizing and generating the performance map for a cooled compressor has been developed. The approach is based upon CFD computations and mean line analysis. Figures of merit that characterize the bulk performance of blade passage flows with and without cooling are extracted from CFD solutions. Such performance characterization is then applied to a preliminary compressor design framework (mean line). The generic nature of this approach makes it suitable for assessing the effect of different types of compressor cooling schemes, such as heat exchange or evaporative cooling (mass injection). Future work will focus on answering system level questions regarding the feasibility of compressor cooling. Specifically, we wish to determine the operational parametric space in which compressor cooling would be advantageous over other high flight Mach number propulsion concepts. In addition, we will explore the design requirements of cooled compressor turbomachinery, as well as the flow phenomena that limit and control its operation, and the technology barriers that must be crossed for its implementation.
The small helium cooled infrared telescope for Spacelab 2 is designed for sensitive mapping of extended, low-surface-brightness celestial sources as well as highly sensitive investigations of the shuttle contamination environment (FPA) for this mission is described as well as the design for a thermally isolated, self-heated J-FET transimpedance amplifier. This amplifier is Johnson noise limited for feedback resistances from less than 10 to the 8th power Omega to greater than 2 x 10 to the 10th power Omega at T = 4.2K. Work on the focal plane array is complete. Performance testing for qualification of the flight hardware is discussed, and results are presented. All infrared data channels are measured to be background limited by the expected level of zodiacal emission.
Two-phase flows under microgravity condition find a large number of important applications in fluid handling and storage, and spacecraft thermal management. Specifically, under microgravity condition heat transfer between heat exchanger surfaces and fluids depend critically on the distribution and interaction between different fluid phases which are often qualitatively different from the gravity-based systems. Heat transfer and flow analysis in two-phase flows under these conditions require a clear understanding of the flow pattern transition and development of appropriate dimensionless scales for its modeling and prediction. The physics of this flow is however very complex and remains poorly understood. This has led to various inadequacies in flow and heat transfer modeling and has made prediction of flow transition difficult in engineering design of efficient thermal and flow systems. In the present study the available published data for flow transition under microgravity condition are considered for mapping. The transition from slug to annular flow and from bubbly to slug flow are mapped using dimensionless variable combination developed in a previous study by the authors. The result indicate that the new maps describe the flow transitions reasonably well over the range of the data available. The transition maps are examined and the results are discussed in relation to the presumed balance of forces and flow dynamics. It is suggested that further evaluation of the proposed flow and transition mapping will require a wider range of microgravity data expected to be made available in future studies.
Two complementary sensors, the DAEDALUS DEI-1260 Multispectral Scanner aboard the NASA U-2 aircraft and the Advanced Very High Resolution Radiometer aboard National Oceanographic and Atmospheric Administration orbiting satellites were tested for their applicability in monitoring and predicting parameters such as fire location, temperature and rate of spread, soil heating and cooling rates, and plume characteristics and dimensions. In addition, the satellite system was tested for its ability to extend the relationships found between fire characteristics and biospheric consequences to regional and global scales. An overall system design is presented, and special requirements are documented for the application of this system for fire research and management.
It is noted that a knowledge of the thermal inertia of the earth's surface can be used in geologic mapping as a complement to surface reflectance data as provided by Landsat. Thermal inertia, which is a body property, cannot be determined directly but can be inferred from radiation temperature measurements made at various times in the diurnal heating cycle, combined with a model of the surface heating processes. A model of this type is developed and applied along with temperature measurements made in the field and by satellite to determine thermal properties of surface materials. An example from a test site in western Nevada is used to demonstrate the utility of this technique.
Measurements made by Viking Lander VL-2 (48 N) have shown that the near-surface wind and temperature regime on Mars displays striking similarities to terrestrial counterparts. The diurnal radiative cycle is responsible for establishment of a well-defined thermal circulation in which downslope (Katabatic) flows prevail during the nighttime hours and weak upslope (anabatic) conditions prevail during the daytime. Previous work has indicated that the slope flows are much like those found on Earth, particularly the Katabatic winds, which show striking similarities to drainage flows observed over Antarctica. The low-level wind regime appears to be an important factor in the scouring of the martian landscape. The north polar cap shows evidence of eolian features such as dunes, frost streaks, and grooves from Viking imagery. The direction of the prevailing wind can in cases be inferred from the eolian features. We examine the thermally induced flows that result from the radiative heating and cooling of the martian north polar region using a comprehensive three-dimensional atmospheric mesoscale numerical model. The same model has been used previously for simulation of Antarctic Katabatic winds. The model equations are written in terrain-following coordinates to allow for irregular terrain; prognostic equations include the flux forms of the horizontal momentum equations, temperature, continuity. A surface energy budget equation is also incorporated in which the surface temperature is determined. Explicit parameterization of both terrestrial (longwave) and solar (shortwave) radiation is included. Turbulent transfer of heat and momentum in the martian atmosphere is assumed to follow the similarity expressions in the surface boundary layer on Earth. The terrain heights for the martian north polar region have been obtained from the U.S. Geological Survey map and digitized onto a 57x57 grid with a spacing of 75 km. The resulting terrain map is shown in Fig. 1. The vertical grid consists of 15 levels (delta equals 0.998, 0.99, 0.98, 0.97, 0.96, 0.94, 0.92, 0.90, 0.85, 0.775, 0.70, 0.60, 0.50, 0.30, 0.10). The high resolution in the lower atmosphere is necessary to capture details of the boundary layer flows. The lowest level corresponds to a height of approximately 20 m above the ground, the seconds level 100 m.
Elevated temperatures resulting from the urban heat island (UHI) effect can have widespread impacts on human health, infrastructure, and ecosystems. These impacts can be exacerbated by changes in climate and extreme variation in regional temperature. By 2030, experts expect Cambridge, Massachusetts will experience warmer than average temperatures, more heat waves, and triple the number of abnormally warm days above 90°F per year. The NASA DEVELOP Program partnered with the City of Cambridge’s Community Development Department and the American Geophysical Union’s Thriving Earth Exchange to inform ongoing efforts aimed at reducing the impacts of urban heat in the city of Cambridge. The team used scenes obtained from High Resolution Orthoimagery and the National Agriculture Imagery Program in conjunction with building footprint data, to calculate rooftop albedo between 2008 and 2018. Using these results, maps displaying building-specific variation in albedo across Cambridge were created. A nighttime land surface temperature (LST) record for June, July, and August between 2003 and 2019 was constructed using the Aqua Moderate Resolution Imaging Spectroradiometer (MODIS) nighttime LST product. Lastly, temperature anomalies were calculated for Cambridge using seasonally averaged nighttime LST values obtained from Aqua MODIS to display ‘hot spots’ for summers between 2004 and 2019. The results of this project were then incorporated into an interactive ArcGIS Dashboard. This work will allow end users to explore spatial and temporal trends in albedo, nighttime LST, and temperature anomalies to assess whether the City of Cambridge is successfully reducing the effects of UHIs.