SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Dye laser gains were measured at various pump-beam irradiances on a dye cell in order to evaluate the feasibility of solar pumping. Rhodamine 6G dye was considered as a candidate for the solar-pumped laser because of its high utilization of the solar spectrum and high quantum efficiency. Measurements show that a solar concentration of 20,000 is required to reach the threshold of the dye.
This paper presents the results of a feasibility study to determine whether the measurements from GPS satellites can be used to estimate the OMV attitude to an accuracy comparable to the onboard sun sensors, i.e., better than 0.5 degree in each axis. The results documented in this paper demonstrate that OMV attitude can be estimated to an accuracy of 0.1 - 0.5 degree in each axis by processing GPS measurements in an onboard integrated, 17-state GPS/inertial navigation filter. The result is particularly significant for missions of short duration burns where accurate attitude information is needed to minimize guidance and control errors. It is shown that the GPS attitude technique described in this paper can be easily implemented in the current OMV navigation system design. Results reported in this paper are expected to support the goal of developing a fault-tolerant guidance, navigation, and control system offering an improved total navigation performance for the OMV.
Various drag accounts for about half of the total drag on commercial aircraft at subsonic cruise conditions. Two avenues are available to achieve drag reduction: either laminar flow control or turbulence manipulation. The present research deals with the latter approach. The primary objective of Phase 2 research was to investigate experimentally the feasibility of substantially reducing the skin-friction drag in a turbulent boundary layer. The method combines the beneficial effects of suction and a longitudinally ribbed surface. At a sufficiently large spanwise separation, the streamwise grooves act as a nucleation site causing a focusing of low-speed streaks over the peaks. Suction is then applied intermittently through longitudinal slots located at selected locations along those peaks to obliterate the low-speed regions and to prevent bursting. Phase 2 research was divided into two tasks. In the first, selective suction from a single streamwise slot was used to eliminate either a single burst-like event or a periodic train of artificially generated bursts in laminar and turbulent boundary layers that develop on a flat plate towed in a water channel. The results indicate that equivalent values of the suction coefficient as low as 0.0006 were sufficient to eliminate the artificially generated bursts in a laminar boundary layer.
By employing technology developed for the Tethered Satellite Program, it appears feasible to obtain Martian dust samples from the atmosphere using an orbiting spacecraft. If collected during an annual dust storm, such a sample would contain a global selection of windborne materials. Atmospheric dust sampling is of importance to the study of Martian surface geochemistry, soil mechanics, atmospheric dynamics, and atmospheric and radiative transfer. Tethered sample return offers two key advantages over a lander sample return: relative simplicity and low spacecraft weight. In another vein, the collection of atmospheric dust by a lander sample return mission is itself of scientific merit. By employing a mast and collection plate aboard a lander mission, it is possible to obtain dust from distant locations transported as entrained material in the local aeolian environment.
A study was undertaken to see if magnetic forces can be used at the Space Station to attract or repel spacecrafts such as the Orbital Manuevering Vehicle (OMV) or the Orbiter. A large magnet, in the form of a current loop, is assumed to be placed at the Space Station and another one on the spacecraft. The expression for the force between the two dipoles (loops) is obtained. Using a force of 15 Newtons (3.4 pounds) in order to move the spacecraft, the number of ampere-turn needed in the current loops was calculated at various distances between them. The expression for the force of attraction between a current loop and a soft magnetic material was also examined and the number of amp-turn needed to provide a force of one-tenth of a pound at various distances is also calculated. This one tenth of a pound force would be used in a life line system for the retrieval of an adrift crewman or tool at the Space Station. The feasibility of using conventional antenna on the Station and the incoming vehicle for attraction or repulsion was also examined.
The bonding of liner material to the inner metal surfaces of solid rocket booster cases is adversely affected by minute amounts of impurities on the metal surface. Suitable non-destructive methods currently used for detecting these surface contaminants do not provide the means of identifying their elemental composition. The feasibility of using isotopic source excited energy dispersive X-ray fluorescence as a possible technique for elemental analysis of such contaminants is investigated. A survey is made of the elemental compositions of both D-6ac steel, a common construction material for the booster cases, and Conoco HD-2 grease, a common surface contamination. Source and detector choices that maximize signal to noise ratio in a Recessed Source Geometry are made. A Monte Carlo simulation is then made of the optimized device incorporating the latest available X-ray constants at the energy of the chosen source to determine the device's response to a D-6ac steel surface contained with Conoco HD-2 grease.
The feasibility of using two intersecting beams for plasma generation in the upper atmosphere as an over-the-horizon radar reflector was investigated. A cube was filled with dry air to a pressure corresponding to the simulated altitude, and two components of a split microwave beam were fed into the cube at right angles. Plasma layers were generated where the two beams intersected. Three critical issues were addressed: (1) reflectivity of the generated plasma layers; (2) propagation of high power microwave pulses; and (3) lifetime of the plasma.
An overview of the Gas-Grain Simulation Facility (GGSF) project and its current status is provided. The proceedings of the Gas-Grain Simulation Facility Experiments Workshop are recorded. The goal of the workshop was to define experiments for the GGSF--a small particle microgravity research facility. The workshop addressed the opportunity for performing, in Earth orbit, a wide variety of experiments that involve single small particles (grains) or clouds of particles. Twenty experiments from the fields of exobiology, planetary science, astrophysics, atmospheric science, biology, physics, and chemistry were described at the workshop and are outlined in Volume 2. Each experiment description included specific scientific objectives, an outline of the experimental procedure, and the anticipated GGSF performance requirements. Since these experiments represent the types of studies that will ultimately be proposed for the facility, they will be used to define the general science requirements of the GGSF. Also included in the second volume is a physics feasibility study and abstracts of example Gas-Grain Simulation Facility experiments and related experiments in progress.
The results of an investigation into the feasibility of using the MPP for direct and large eddy simulations of the Navier-Stokes equations is presented. A major part of this study was devoted to the implementation of two of the standard numerical algorithms for CFD. These implementations were not run on the Massively Parallel Processor (MPP) since the machine delivered to NASA Goddard does not have sufficient capacity. Instead, a detailed implementation plan was designed and from these were derived estimates of the time and space requirements of the algorithms on a suitably configured MPP. In addition, other issues related to the practical implementation of these algorithms on an MPP-like architecture were considered; namely, adaptive grid generation, zonal boundary conditions, the table lookup problem, and the software interface. Performance estimates show that the architectural components of the MPP, the Staging Memory and the Array Unit, appear to be well suited to the numerical algorithms of CFD. This combined with the prospect of building a faster and larger MMP-like machine holds the promise of achieving sustained gigaflop rates that are required for the numerical simulations in CFD.
The heavy rain aerodynamic performance penalty program is detailed. This effort supported the design of a fullscale test program as well as examined the feasibility of estimating the degradation of performance of airfoils from first principles. The analytic efforts were supplemented by a droplet splashback test program in an attempt to observe the physics of impact and generation of ejecta. These tests demonstrated that the interaction of rain with an airfoil is a highly complex phenomenon and this interaction is not likely to be analyzed analytically with existing tools.
The results of a feasibility study conducted to determine the possibility of passively measuring the vertical profile of carbon monoxide in the troposphere on a global basis are presented. The instrument considered is a nadir-viewing gas correlation filter radiometer (GCFR). The basic instrument concept and radiative transfer equations are presented. The calculated signal functions, signal levels, sensitivity, and system noise levels of a spaceborne GCFR instrument are presented and discussed. It is concluded that a three- or four-level measurement of the atmospheric carbon monoxide mixing ratio in the troposphere is possible with this type of instrument.
This paper is a study of the feasibility of a 35-GHz microwave power transmission system in space. It was found that a dc to dc transmission efficiency better than 50 percent can be achieved over a distance of 50 km by using a transmitting antenna of 20 m in diameter and a receiving antenna of 40 m in diameter. Technology requirements at 35 GHz have been assessed and several stages of development have been proposed.
The feasibility of controlling vortex interactions or merger on a blended chine forebody and delta wing configuration was experimentally investigated. Low-speed wind tunnel diagnostics using smoke visualizations and wing upper-surface pressure measurements were performed on a generic 60 deg delta and chine forebody model, to assess chine modifications and leading edge flaps. Both techniques were shown to promote uncoupled vortex flows at high angles of attack and sideslip, with significant influence on the wing flow field, indicating potential for alleviating adverse high-alpha characteristics of blended chine swept wing configurations.
The crew emergency return vehicle (CERV) autoland feasibility study focused on determining the controllability of the NASA Langley high lift over drag CERV for performing an automatic landing at a prescribed runway. An autoland system was developed using integral linear quadratic Gaussian (LQG) design techniques. The design was verified using a nonlinear 6 DOF simulation. Simulation results demonstrate that the CERV configuration is a very flyable configuration for performing an autoland mission. Adequate stability and control was demonstrated for wind turbulence and wind shear. Control surface actuator requirements were developed.
Laser Induced Fluorescence (LIF) studies are carried out on nitric oxide and oxygen molecules in the arc jet flows at the NASA Johnson Space Center Reentry Testing Facility. Measurements are taken in the free stream and from a blunt body shock layer. Tests are performed under different flow conditions to determine the feasibility and sensitivity of the LIF technique for various species. This is developed as a part of high enthalpy flow diagnostics and will be useful to elucidate the rotational and vibrational temperatures. Adequate sensitivity for the detection of O(2) and NO is demonstrated. Proposed improvements of the existing system are presented.
The feasibility of an experiment which will provide an on-orbit validation of Controls-Structures Interaction (CSI) technology, was investigated. The experiment will demonstrate the on-orbit characterization and flexible-body control of large flexible structure dynamics using the shuttle Remote Manipulator System (RMS) with an attached payload as a test article. By utilizing existing hardware as well as establishing integration, operation and safety algorithms, techniques and procedures, the experiment will minimize the costs and risks of implementing a flight experiment. The experiment will also offer spin-off enhancement to both the Shuttle RMS (SRMS) and the Space Station RMS (SSRMS).
A program to demonstrate the feasibility of a high-performance 445 Newton (100 lb(sub f)) NTO/NMH rocket engine is presented. An existing high-performance injector was coupled with three different thrust chambers to acquire test data for the program. A stainless-steel sea-level chamber was used for test stand checkout, calibration and initial injector performance determinations. Two high-temperature iridium lined rhenium thrust chambers were used to determine altitude performance and durability. The first chamber was tested for a total duration of 3381 s and the second was tested for a total duration of 15,000 s with no measurable degradation. Extrapolation of epsilon = 44:1 experimental data to the recommended epsilon = 467:1 expansion nozzle, using the JANNAF methodology, showed that a performance of 3138 to 3167 N-s/kg (320 to 323 lb(sub f-s)/lb(sub m) could be achieved with the present design. Recommendations are presented which would allow a redesigned engine to achieve the 3195 N-s/kg (326 lb(sub f-s)/lb(sub m)) program goal.
The feasibility is discussed for an experimental program for studying the behavior of acoustic wave propagation in the presence of strong gradients of pressure, temperature, and flow. Theory suggests that gradients effects can be experimentally observed as resonant frequency shifts and mode shape changes in a waveguide. A convenient experimental geometry for such experiments is the annular region between two co-rotating cylinders. Radial temperature gradients in a spinning annulus can be generated by differentially heating the two cylinders via electromagnetic induction. Radial pressure gradients can be controlled by varying the cylinder spin rates. Present technology appears adequate to construct an apparatus to allow independent control of temperature and pressure gradients. A complicating feature of a more advanced experiment, involving flow gradients, is the requirement for independently controlled cylinder spin rates. Also, the boundary condition at annulus terminations must be such that flow gradients are minimally disturbed. The design and construction of an advanced apparatus to include flow gradients will require additional technology development.