SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Simple battery-powered test circuit will contribute negligible error when taking open-loop measurements of gain and phase parameters. This is especially helpful when measuring high-grain circuits containing integrators.
A method was developed to determine the accuracy of a rangefinder when errors exist due to the test setup. An analytic procedure was developed to evaluate actual data from a test performed on the laser rangefinder for the Mars rover project.
A barotropic model of the atmosphere was used to test various sources of forecast error. These errors are classified as truncation error, physical error, or initial error. It was shown that growth patterns due to each category differ significantly. Initial errors were shown not to grow in a barotropic model contrary to reports of other studies which indicate that they basically do grow. Also, random initial errors were shown to decrease due to the filtering effect of the model itself. Results seem to indicate that instabilities are required for error growth, be they barotropic or baroclinic, and that random errors are not representative of true initial conditions.
Assumption that sample comes from population with particular distribution is made with confidence C if data lie between certain bounds. These "confidence bounds" depend on C and assumption about distribution of sampling errors around regression line. Graphical test criteria using tolerance bounds are applied in industry where statistical analysis influences product development and use. Applied to evaluate equipment life.
Known models of Shuttle Solid Rocket Motor (SRM) performance have failed to produce pressure-time traces which accurately matched actual motor performance, especially during the first 5 seconds after ignition and during the last quarter of web burn time. Efforts to compensate for these differences in model reconstruction and actual performance resulted in resorting to the use of a Burning Anomaly Rate Function (BARF). It was suspected that propellant erosive burning was primarily responsible for the variation of model from actual results. The three dimensional Hercules Grain Design and Internal Ballistics Evaluation Program was made operational and slightly modified and an extensive trial and error effort was begun to test the hypothesis of erosive burning as an explanation of the burning anomaly. It was found that introduction of erosive burning (using Green's erosive burning equation) over portions of the aft segment grain and above a threshold gas Mach number did, in fact, give excellent agreement with the actual motor trace.
A helicopter flight test program undertaken to evaluate the performance of Tetrad (a strap down, laser gyro, inertial navigation system) is described. The results of 34 flights show a mean final navigational velocity error of 5.06 knots, with a standard deviation of 3.84 knots; a corresponding mean final position error of 2.66 n. mi., with a standard deviation of 1.48 n. mi.; and a modeled mean position error growth rate for the 34 tests of 1.96 knots, with a standard deviation of 1.09 knots. No laser gyro or accelerometer failures were detected during the flight tests. Off line parity residual studies used simulated failures with the prerecorded flight test and laboratory test data. The airborne Tetrad system's failure--detection logic, exercised during the tests, successfully demonstrated the detection of simulated ""hard'' failures and the system's ability to continue successfully to navigate by removing the simulated faulted sensor from the computations. Tetrad's four ring laser gyros provided reliable and accurate angular rate sensing during the 4 yr of the test program, and no sensor failures were detected during the evaluation of free inertial navigation performance.
A statistical method for predicting tropical cyclone positions 12, 24, 48 and 72 hours after initial observation is described. Satellite measurements were at the 11.0 micron channel and at equivalent blackbody temperatures which give representations of the structure of the cyclones, as well as the circulation features surrounding them. In all, 197 individual measurements for blackbody temperature were made. Algorithms prepared from a single satellite image included 14 climatological and persistence type variables, and are based on eigenvector preprocessing and a series of independent screening tests. The independent tests showed that the average error made by the algorithms from the single satellite observation were comparable to the 48 hr Joint Typhoon Warning Center (JTWC) forecast and were about 10 percent better for 72 hr forecasts. Forecasts using only climatological persistence variables were found to be 20 percent worse than JTWC for 24 hr forecasts and 10 percent worse for 48 and 72 hr forecasts. When both satellite and nonsatellite variables were included, it was found that the method was comparable to JTWC for the 24 and 48 hr forecasts and about 25 percent better for the 72 hr forecasts.
Flexural clamp eliminates problems of operator variability. Extensometer opens and closes like clothespin and placed easily on specimen. Dimensions of block specimen are 1 by 1 by 2.2 inches (2.54 by 2.54 by 5.59 centimeters). By constructing central flexure units of various widths, one adapts extensometer to handle specimens ranging from thin strips to those many inches thick. New design reduces measurement errors caused by variability among test operators.
A helicopter flight-test program to evaluate the performance of Honeywell's Tetrad - a strapdown, laser gyro, inertial navitation system is discussed. The results of 34 flights showed a mean final navigational velocity error of 5.06 knots, with a standard deviation of 3.84 knots; a corresponding mean final position error of 2.66 n.mi., with a standard deviation of 1.48 n.m.; and a modeled mean-position-error growth rate for the 34 tests of 1.96 knots, with a standard deviation of 1.09 knots. Tetrad's four-ring laser gyros provided reliable and accurate angular rate sensing during the test program and on sensor failures were detected during the evaluation. Criteria suitable for investigating cockpit systems in rotorcraft were developed. This criteria led to the development of two basic simulators. The first was a standard simulator which could be used to obtain baseline information for studying pilot workload and interactions. The second was an advanced simulator which integrated the RODAAS developed by Honeywell into this simulator. The second area also included surveying the aerospace industry to determine the level of use and impact of microcomputers and related components on avionics systems.
Extendable Integrated Support Environment (EISE) is a real-time computer network consisting of commercially available hardware and software components to support systems level integration, modifications, and enhancement to weapons systems. The EISE approach offers substantial potential savings by eliminating unique support environments in favor of sharing common modules for the support of operational weapon systems. An expert system is being developed that will help support diagnosing faults in this network. This is a multi-level, multi-expert diagnostic system that uses experiential knowledge relating symptoms to faults and also reasons from structural and functional models of the underlying physical model when experiential reasoning is inadequate. The individual expert systems are orchestrated by a supervisory reasoning controller, a meta-level reasoner which plans the sequence of reasoning steps to solve the given specific problem. The overall system, termed the Diagnostic Executive, accesses systems level performance checks and error reports, and issues remote test procedures to formulate and confirm fault hypotheses.
A limited flight experiment was conducted to document the ground-effect characteristics of the X-29A research airplane. This vehicle has an aerodynamic platform which includes a forward-swept wing and close-coupled, variable incidence canard. The flight-test program obtained results for errors in the airdata measurement and for incremental normal force and pitching moment caused by ground effect. Correlations with wind-tunnel and computational analyses were made. The results are discussed with respect to the dynamic nature of the flight measurements, similar data from other configurations, and pilot comments. The ground-effect results are necessary to obtain an accurate interpretation of the vehicle's landing characteristics. The flight data can also be used in the development of many modern aircraft systems such as autoland and piloted simulations.
A system consisting of a single charge coupled device (CCD) video camera, computer controlled video digitizer, and software to automate the measurement was developed to measure the location of bullet holes in targets at the International Shooters Development Fund (ISDF)/NASA Ballistics Tunnel. The camera/digitizer system is a crucial component of a highly instrumented indoor 50 meter rifle range which is being constructed to support development of wind resistant, ultra match ammunition. The system was designed to take data rapidly (10 sec between shoots) and automatically with little operator intervention. The system description, measurement concept, and procedure are presented along with laboratory tests of repeatability and bias error. The long term (1 hour) repeatability of the system was found to be 4 microns (one standard deviation) at the target and the bias error was found to be less than 50 microns. An analysis of potential errors and a technique for calibration of the system are presented.
A limited flight experiment was conducted to document the ground effect characteristics of the X-29A research aircraft. This vehicle has an aerodynamic platform which includes a forward-swept wing and close-coupled, variable incidence canard. The flight-test program obtained results for errors in the air data measurement and for incremental normal force and pitching moment caused by ground effect. Correlations with wind-tunnel and computational analyses were made. The results are discussed with respect to the dynamic nature of the flight measurements, similar data from other configurations, and pilot comments. The ground effect results are necessary to obtain an accurate interpretation of the vehicle's landing characteristics. The flight data can also be used in the development of many modern aircraft systems such as autoland and piloted simulation.
The Advanced Rotorcraft Transmission (ART) Program was initiated to advance the state of the art for rotorcraft transmissions. The goal of the ART Program was to develop and demonstrate the technologies needed to reduce transmission weight by 25 pct. and reduce noise by 10 dB while obtaining a 5000 hr 'mean time between failure'. The research done under the ART Program is summarized. A split path design was selected as best able to meet the program goals. Key part technologies needed for this design were identified, studied, and developed. Two of these technologies are discussed in detail: the load sharing of split path designs including the use of a compliant elastomeric torque splitter and the application of a high ratio, low pitch line velocity gear mesh. Development of an angular contact spherical roller bearing, transmission error analysis, and fretting fatigue testing are discussed. The technologies for a light weight, quiet, and reliable rotorcraft transmission were demonstrated.
The Advanced Rotorcraft Transmission (ART) Program was initiated to advance the state of the art for rotorcraft transmissions. The goal of the ART Program was to develop and demonstrate the technologies needed to reduce transmission weight by 25 pct and reduce noise by 10 dB while obtaining a 5000 hr 'mean time between failure'. The research done under the ART Program is summarized. A split path design was selected as best able to meet the program goals. Key part technologies needed for this design were identified, studied, and developed. Two of these technologies are discussed in detail: the load sharing of split path designs including the use of a compliant elastomeric torque splitter and the application of a high ratio, low pitch line velocity gear mesh. Development of an angular contact spherical roller bearing, transmission error analysis, and fretting fatigue testing are discussed. The technologies for a light weight, quiet, and reliable rotorcraft transmission were demonstrated.
The efficient solution of the eigenvalue problem that results from inserting passive dampers with variable stiffness and damping coefficients into a structure is addressed. Eigenanalysis of reduced models obtained by retaining a number of normal modes augmented with Ritz vectors corresponding to the static solutions resulting from the load patterns introduced by the dampers has been empirically shown to yield excellent approximations to the full eigenvalue problem. An analysis of this technique in the case of a single damper is presented. A priori and a posteriori error estimates are generated and tested on numerical examples. Comparison theorems with modally truncated models and a Markov parameter matching reduced-order model are derived. These theorems corroborate the heuristic that residual flexibility methods improve low-frequency approximation of the system. The analysis leads to other techniques for eigenvalue approximation. Approximate closed-form solutions are derived that include a refinement to eigenvalue derivative methods for approximation. An efficient Newton scheme is also developed. A numerical example is presented demonstrating the effectiveness of each of these methods.
The variation of the coefficient of discharge with the length-diameter ratio of the orifice was determined for nozzles having single orifice 0.008 and 0.020 inch in diameter. Ratios from 0.5 to 10 were investigated at injection pressures from 500 to 5,000 pounds per square inch. The tests showed that, within the error of the observation, the coefficients were the same whether the nozzles were assembled at the end of a constant tube or in an automatic injection valve having a plain stem.
We present an outline of an algorithm to generate artificial helioseismic time-series, taking into account as much as possible of the knowledge we have on solar oscillations. The hope is that it will be possible to find the causes of some of the systematic errors in analysis algorithms by testing them with such artificial time-series.