Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “directional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Analysis of a Decision-Directed Receiver with Unknown Priors

A decision-directed receiver (DDR) uses previous outputs (decisions) to estimate unknown parameters and, on the basis of these estimates, modifies the detector structure for subsequent decisions. Although the DDR is less complex to instrument than other adaptive schemes, inherent in the decision-directed approach is the possibility of a runaway. This occurs when the detector commits a sequence of decision errors resulting in a degradation of parameter estimates, which, in turn, results in a further deterioration of detector performance. Because of the dependencies introduced by the learning process, runaway is difficult to analyze. In this paper, a DDR with unknown a priori probabilities is considered. The priors are estimated by the relative frequency of decisions of that event. For binary detection, it is shown that there is a positive probability of a runaway (the estimates converge to 1 or 0), which equals 1 if the signal-to-noise ratio is below a critical value. A tight bound on the probability of a runaway is obtained by approximating the learning process by a random walk with independent increments. The analysis demonstrates that a runaway is quite improbable even for moderate signal-to-noise ratios. The analysis is extended to multiple signals and to the situation where the estimates of the priors are updated continuously through exponential weighting rather than allowed to converge.

Davisson, Lee D.↗

Wind tunnel study of slot spoilers for direct lift control

An investigation was conducted in a 300-mph 7- by 10- foot tunnel to obtain data for a slot spoiler direct lift control system. Slot spoilers are believed to have advantages over flap-type direct lift control (DLC) systems because of the small amount of power required for actuation. These tests, run at a Reynolds number of 1,400,000 showed that up to 78 percent of the lift due to flap deflection could be spoiled by opening several spanwise slots within the flaps. For a given lift change the drag change was significantly less than that which would be obtained by a variable flap DLC system. A nozzle-shaped slot was the most effective of the slot shapes tested.

Andrisani, D., II↗

Directive gain of circular Taylor patterns.

The practicality of various classes of planar aperture distributions in high-gain antenna design is discussed, and optimal circular Taylor distributions are illustrated. In particular, the directive gain of circular Taylor patterns is determined. It is shown that so-called optimum patterns - i.e., uniform sidelobes in all planes, are severly limited for planar apertures because of excessive sidelobe power. The optimum directive gain of the circular Taylor pattern with a given sidelobe level can be obtained by appropriate design.

Rudduck, R. C.↗

Skin and muscle components of forearm blood flow in directly heated resting man.

Changes in forearm muscle blood flow (FMBF) during direct whole-body heating were measured in 17 normal subjects using three different methods. We conclude that FMBF is not increased by direct whole-body heating. Since renal and splanchnic blood flow fall 30% under these conditions, maximal total skin blood flow in 12 previously studied subjects can be estimated from the rise in cardiac output to be 7.6 L/min (3.0-11.1 L/min).

Detry, J.-M. R.↗

Experiment and analysis of directional effects on radiant heat transfer.

Critical examination of the validity of the commonly used simplified models for predicting local and overall radiant heat interchange among real surfaces. The spectral local irradiation was measured at wavelengths of 3.08 and 4.51 microns in a configuration consisting of three plane parallel surfaces of finite extent. The test surfaces were gold with mechanical roughness and temperature varying from 0.02 to 7.1 microns and 77 to 760 K, respectively. Comparisons between experimental data and predictions for six different models ranging from the simple diffuse to the most detailed diffuse-plus-specular-directional-property model with specular component calculated according to Beckmann are presented. It is shown that the calculation of the overall irradiation using appropriate constant-property models agrees well with the experimental data to within combined experimental and analytical uncertainty. In general, it is concluded that for accurate prediction of local irradiation the directional characteristics of the surfaces must be considered.

Toor, J. S.↗

Direction-specific adaptation effects acquired in a slow rotation room

Thirty-eight subjects were required to execute 120 head movements in a slow rotation room at each 1-rpm increase in velocity of the room between 0 and 6 rpm and, after a single-step gradual return to zero velocity, execute 120 head movements either immediately after the return or after delay periods varying from 1 to 24 hours unless, at any time, more than mild symptoms of motion sickness were elicited. A second stress profile differed by the sequential addition of an incremental adaptation schedule in which the direction of rotation was reversed. The experimental findings demonstrated the acquisition of direction-specific adaptation effects that underwent spontaneous decay with a short time constant (hours). Speculations are presented which could account for the simultaneous acquisition of short-term and long-term adaptation effects. The findings support the theory that motion sickness, although a consequence of vestibular stimulation, has its immediate origin in nonvestibular systems, implying a faculative or temporary linkage between the vestibular and nonvestibular systems.

Graybiel, A.↗

Development of high temperature fasteners using directionally solidified eutectic alloys

The suitability of the eutectics for high temperature fasteners was investigated. Material properties were determined as a function of temperature, and included shear parallel and perpendicular to the growth direction and torsion parallel to it. Techniques for fabricating typical fastener shapes included grinding, creep forming, and direct casting. Both lamellar Ni3Al-Ni3Nb and fibrous (Co,Cr,Al)-(Cr,Co)7C3 alloys showed promise as candidate materials for high temperature fastener applications. A brief evaluation of the performance of the best fabricated fastener design was made.

George, F. D.↗

A directional low energy gamma-ray detector

The sensitivity of a directional gamma ray detector, which relies on blocking a source to determine its direction and energy spectrum, is calculated and compared to the more conventional well-shaped shielded detectors. It is shown that such an anticollimator detection system provides a basis for measuring the celestial diffuse gamma ray background, gamma ray sources and bursts with good energy, angular, and time resolution, and that additionally the system is 20 to 50 times as sensitive as conventional detectors when compared on a per unit mass basis.

Morfill, G.↗

Direction-specific adaptation effects acquired in a slow rotation room.

Thirty-eight subjects were required to execute 120 head movements in a slow rotation room at each 1-rpm increase in velocity of the room between 0 and 6 rpm and, after a single-step gradual return to zero velocity, execute 120 head movements either immediately after return or after delay periods varying from 1 to 24 hours unless, at any time, more than mild symptoms of motion sickness were elicited. A second stress profile differed by the sequential addition of an incremental adaptation schedule (identical to the first) in which the direction of rotation was reversed. The experimental findings demonstrated the acquisition of direction-specific adaptation effects that underwent spontaneous decay with a short time constant (hours). With their disappearance a nondirection-specific adaptation was revealed with a long-time constant (days). Speculations are presented which could account for the simultaneous acquisition of short-term and long-term adaptation effects.

Graybiel, A.↗

Degree and direction of polarization of multiple scattered light. II - Earth's atmosphere with aerosols.

The radiance, polarization, and direction of polarization of the radiation reflected and transmitted through the atmosphere are calculated by a Monte Carlo method on the basis of a realistic model of the atmosphere. The calculated polarization is shown to depend on the aerosol amount and to have normally a value intermediate between that for pure Rayleigh and pure aerosol scattering. The polarization for multiple scattered photons is usually less than the value calculated for single scattering, but may be larger in low-polarization regions near other regions of high polarization. The direction of polarization shows little variation with either the aerosol amount or the value of the surface albedo.

Plass, G. N.↗

An analysis of jet noise directivity.

This paper is intended for pointing out several factors which may be important to the calculation of directivity patterns of jet noise. In a hot, high speed jet the directional pattern can be divided into a maximum of four zones. The convection law and the correspondence between the sound field and turbulence are different in each zone. The convection law for high and low frequencies is also different. Numerical examples are presented in parallel to the discussions.

Pao, S. P.↗

Directivity of high-energy X-ray emission during flares.

The solar X-ray flare model of Jager and Kundu (1963), supported by the direct evidence recently provided by Tindo et al. (1972) for the presence of radial electron beams indicated in Jager-Kundu's model, is discussed with respect to its apparent conflict with Ohki's (1969) and Pinter's (1969) indications of a directivity effect likely to occur for X-ray flares at very high photon energies. An attempt is made to explain this apparent conflict.

Phillips, K. J. H.↗

Direct numerical solution of three-dimensional equations containing elliptic operators.

A direct three-dimensional elliptic solver is presented for application in a wide class of numerical methods for solving partial differential equations in physics and engineering. The derived algorithm and FORTRAN code implement Buzbee, Golub and Nielson's proposed extension of Buneman's Cyclic-Reduction Poisson solver to three dimensions. Both a 'most direct' cyclic reduction and a revised method (to eliminate roundoff error difficulties) are derived. Tests on an IBM 360/67 computer, using various optional combinations of subroutines, showed significant differences in accuracy and computing time, with the optimum subroutine combination depending on mesh size.

Martin, E. D.↗

On the role of the radiation directivity in noise reduction for STOL aircraft.

The radiation characteristics of distributed randomly fluctuating acoustic sources when shielded by finite surfaces are discussed briefly. A number of model tests using loudspeakers as artificial noise sources with a given broadband power density spectrum are used to demonstrate the effectiveness of reducing the radiated noise intensity in certain directions due to shielding. In the lateral direction of the source array noise reductions of 12 dB are observed with relatively small shields. The same shields reduce the backward radiation by approximately 20 dB. With the results obtained in these acoustic model tests the potentials of jet noise reduction of jet flap propulsion systems applicable in future STOL aircraft are discussed. The jet flap configuration as a complex aerodynamic noise source is described briefly.

Gruschka, H. D.↗

Structural optimization by methods of feasible directions.

A general design algorithm based on methods of feasible directions is presented. Zoutendijk's method of feasible directions is first presented as applied to structural design. This method is modified to improve numerical stability of the design process and is then further modified to deal efficiently with infeasible designs. The algorithm requires the analytic gradient of the objective function and the constraint functions which are active at a given stage in the design process. Gradient information is not required for nonactive constraints. Complex constraint functions may be ignored in the initial design stages because violation of these constraints is efficiently overcome later in the design process. The algorithm is demonstrated with elastic design of redundant trusses.

Vanderplaats, G. N.↗