Results for “configuration mixing” — Page 30

NASA NTRS1975

Numerical techniques for the solution of the compressible Navier-Stokes equations and implementation of turbulence models

The time-splitting explicit numerical method of MacCormack is applied to separated turbulent boundary layer flow problems. Modifications of this basic method are developed to counter difficulties associated with complicated geometry and severe numerical resolution requirements of turbulence model equations. The accuracy of solutions is investigated by comparison with exact solutions for several simple cases. Procedures are developed for modifying the basic method to improve the accuracy. Numerical solutions of high-Reynolds-number separated flows over an airfoil and shock-separated flows over a flat plate are obtained. A simple mixing length model of turbulence is used for the transonic flow past an airfoil. A nonorthogonal mesh of arbitrary configuration facilitates the description of the flow field. For the simpler geometry associated with the flat plate, a rectangular mesh is used, and solutions are obtained based on a two-equation differential model of turbulence.

Baldwin, B. S.↗

NASA NTRS1985

Dilution jet mixing program, phase 3

The main objectives for the NASA Jet Mixing Phase 3 program were: extension of the data base on the mixing of single sided rows of jets in a confined cross flow to discrete slots, including streamlined, bluff, and angled injections; quantification of the effects of geometrical and flow parameters on penetration and mixing of multiple rows of jets into a confined flow; investigation of in-line, staggered, and dissimilar hole configurations; and development of empirical correlations for predicting temperature distributions for discrete slots and multiple rows of dilution holes.

Srinivasan, R.↗

NASA NTRS1995

Moving base simulation of an ASTOVL lift-fan aircraft

Using a generalized simulation model, a moving-base simulation of a lift-fan short takeoff/vertical landing fighter aircraft was conducted on the Vertical Motion Simulator at Ames Research Center. Objectives of the experiment were to (1) assess the effects of lift-fan propulsion system design features on aircraft control during transition and vertical flight including integration of lift fan/lift/cruise engine/aerodynamic controls and lift fan/lift/cruise engine dynamic response, (2) evaluate pilot-vehicle interface with the control system and head-up display including control modes for low-speed operational tasks and control mode/display integration, and (3) conduct operational evaluations of this configuration during takeoff, transition, and landing similar to those carried out previously by the Ames team for the mixed-flow, vectored thrust, and augmentor-ejector concepts. Based on results of the simulation, preliminary assessments of acceptable and borderline lift-fan and lift/cruise engine thrust response characteristics were obtained. Maximum pitch, roll, and yaw control power used during transition, hover, and vertical landing were documented. Control and display mode options were assessed for their compatibility with a range of land-based and shipboard operations from takeoff to cruise through transition back to hover and vertical landing. Flying qualities were established for candidate control modes and displays for instrument approaches and vertical landings aboard an LPH assault ship and DD-963 destroyer. Test pilot and engineer teams from the Naval Air Warfare Center, Boeing, Lockheed, McDonnell Douglas, and the British Defence Research Agency participated in the program.

Chung, William W. Y.↗

NASA NTRS2008

Evolutionary Paths to Internationally-Standardized Space Internetworking

The space community is now poised at the start of an exciting new era of space exploration, where many different organization will be launching spacecraft to investigate nearby bodies, such as the Moon and Mars. International fleets of spacecraft are thus likely to begin to fly and interoperability will often become a mission-enabling technology. These fleets will require a mix of powerful data communications capabilities to be available, ranging from conventional point-to-point architectures to new configurations supporting internetworked operations. This paper reviews the various CCSDS capabilities to support fully-standardized in-space internetworking, and outlines a strategy for smoothly evolving into the new era with minimum impact on the highly successful installed base of CCSDS-compatible systems, which are now widely deployed across the international space community.

Space Internet↗

NASA NTRS2015

Downscaling GISS ModelE Boreal Summer Climate over Africa

The study examines the perceived added value of downscaling atmosphere-ocean global climate model simulations over Africa and adjacent oceans by a nested regional climate model. NASA/Goddard Institute for Space Studies (GISS) coupled ModelE simulations for June- September 1998-2002 are used to form lateral boundary conditions for synchronous simulations by the GISS RM3 regional climate model. The ModelE computational grid spacing is 2deg latitude by 2.5deg longitude and the RM3 grid spacing is 0.44deg. ModelE precipitation climatology for June-September 1998-2002 is shown to be a good proxy for 30-year means so results based on the 5-year sample are presumed to be generally representative. Comparison with observational evidence shows several discrepancies in ModelE configuration of the boreal summer inter-tropical convergence zone (ITCZ). One glaring shortcoming is that ModelE simulations do not advance the West African rain band northward during the summer to represent monsoon precipitation onset over the Sahel. Results for 1998-2002 show that onset simulation is an important added value produced by downscaling with RM3. ModelE Eastern South Atlantic Ocean computed sea-surface temperatures (SST) are some 4 K warmer than reanalysis, contributing to large positive biases in overlying surface air temperatures (Tsfc). ModelE Tsfc are also too warm over most of Africa. RM3 downscaling somewhat mitigates the magnitude of Tsfc biases over the African continent, it eliminates the ModelE double ITCZ over the Atlantic and it produces more realistic orographic precipitation maxima. Parallel ModelE and RM3 simulations with observed SST forcing (in place of the predicted ocean) lower Tsfc errors but have mixed impacts on circulation and precipitation biases. Downscaling improvements of the meridional movement of the rain band over West Africa and the configuration of orographic precipitation maxima are realized irrespective of the SST biases.

Regional climate models↗

NASA NTRS2000

Acoustic and Aerothermal Performance Test of the Axisymmetric Coannular Ejector Nozzle: Acoustic Performance - Volume 2

Acoustic and propulsion performance testing of a model-scale Axisymmetric Coannular Ejector nozzle was conducted in the Boeing Low-speed Aeroacoustic Facility. This nozzle is a plug nozzle with an ejector design to provide aspiration of about 20% of the engine flow. A variety of mixing enhancers were designed to promote mixing of the engine and the aspirated flows. These included delta tabs, tone-injection rods, and wheeler ramps. This report addresses the acoustic aspects of the testing. The spectral characteristics of the various configurations of the nozzle are examined on a model-scale basis. This includes indentifying particular noise sources contributing to the spectra and the data are projected to full-scale flyover conditions to evaluate the effectiveness of the nozzle, and of the various mixing enhancers, on reducing the Effective Perceived Noise Levels.

Herkes, William↗

NASA NTRSDate not supplied

Pretest Simulations of a Supersonic Mixing and Combustion Validation Experiment to Assess Sensitivities

The reliance on CFD simulations to develop, design, and optimize scramjet systems (or components) has become commonplace. This reliance inevitably hinges on the ability of the computational analyst to quantify the level of confidence in their computational results. Unfortunately, nearly all the measured data available for this assessment comes from antiquated experimental datasets, or from tests that focused on the extraction of scramjet system (or component) performance. The objective of a CFD validation experiment is to quantify the predictive accuracy of one or more of the CFD physics submodels, implying that other uncertainties related to replicating the facility flow environment (e.g., knowledge of boundary conditions) must be minimized to the extent possible. This inevitably places stringent requirements on the quality and quantity of measurements taken to accurately specify inflow, outflow, and surface conditions for the CFD simulations; in addition to the measurements taken for the validation of physics submodels. This places additional demands on the experimental process above and beyond those for test article performance assessment. A recent high speed code credibility workshop series sponsored by AFRL identified a gap in existing validation data for fundamental assessments of turbulent mixing and combustion CFD closure models at scramjet engine relevant conditions. To address this gap, engineers at AFRL have designed a coaxial jet flame configuration that will be tested at two facilities (Research Cell 19 at the Air Force Research Lab, and at Purdue University). The effort described here documents pretest simulations of this validation experiment with the goal of fleshing out the extent of the facility flowpath that must be included to adequately reproduce the facility test section flow environment. The findings indicate that the flow around the support structure for the fuel injection centerbody upstream of the facility nozzle generates disturbances that persist throughout the nozzle expansion process; corrupting the azimuthal symmetry that was desired in the fuel/air mixing region of the test section. Simulations without this support structure maintained a high degree of azimuthal symmetry up until the fuel injection plane. However, even in this scenario the azimuthal symmetry was not maintained once the centerbody boundary layer transitioned to a wake flow downstream of the fuel injection plane.

CFD↗

NASA NTRSDate not supplied

Pretest Simulations of a Supersonic Mixing and Combustion Validation Experiment to Assess Sensitivities

The reliance on CFD simulations to develop, design, and optimize scramjet systems (or components) has become commonplace. This reliance inevitably hinges on the ability of the computational analyst to quantify the level of confidence in their computational results. Unfortunately, nearly all the measured data available for this assessment comes from antiquated experimental datasets, or from tests that focused on the extraction of scramjet system (or component) performance. The objective of a CFD validation experiment is to quantify the predictive accuracy of one or more of the CFD physics submodels, implying that other uncertainties related to replicating the facility flow environment (e.g., knowledge of boundary conditions) must be minimized to the extent possible. This inevitably places stringent requirements on the quality and quantity of measurements taken to accurately specify inflow, outflow, and surface conditions for the CFD simulations; in addition to the measurements taken for the validation of physics submodels. This places additional demands on the experimental process above and beyond those for test article performance assessment. A recent high speed code credibility workshop series sponsored by AFRL identified a gap in existing validation data for fundamental assessments of turbulent mixing and combustion CFD closure models at scramjet engine relevant conditions. To address this gap, engineers at AFRL have designed a coaxial jet flame configuration that will be tested at two facilities (Research Cell 19 at the Air Force Research Lab, and at Purdue University). The effort described here documents pretest simulations of this validation experiment with the goal of fleshing out the extent of the facility flowpath that must be included to adequately reproduce the facility test section flow environment. The findings indicate that the flow around the support structure for the fuel injection centerbody upstream of the facility nozzle generates disturbances that persist throughout the nozzle expansion process; corrupting the azimuthal symmetry that was desired in the fuel/air mixing region of the test section. Simulations without this support structure maintained a high degree of azimuthal symmetry up until the fuel injection plane. However, even in this scenario the azimuthal symmetry was not maintained once the centerbody boundary layer transitioned to a wake flow downstream of the fuel injection plane.

CFD↗

NASA NTRS2000

AST Critical Propulsion and Noise Reduction Technologies for Future Commercial Subsonic Engines: Separate-Flow Exhaust System Noise Reduction Concept Evaluation

This report describes the work performed by General Electric Aircraft Engines (GEAE) and Allison Engine Company (AEC) on NASA Contract NAS3-27720 AoI 14.3. The objective of this contract was to generate quality jet noise acoustic data for separate-flow nozzle models and to design and verify new jet-noise-reduction concepts over a range of simulated engine cycles and flight conditions. Five baseline axisymmetric separate-flow nozzle models having bypass ratios of five and eight with internal and external plugs and 11 different mixing-enhancer model nozzles (including chevrons, vortex-generator doublets, and a tongue mixer) were designed and tested in model scale. Using available core and fan nozzle hardware in various combinations, 28 GEAE/AEC separate-flow nozzle/mixing-enhancer configurations were acoustically evaluated in the NASA Glenn Research Center Aeroacoustic and Propulsion Laboratory. This report describes model nozzle features, facility and data acquisition/reduction procedures, the test matrix, and measured acoustic data analyses. A number of tested core and fan mixing enhancer devices and combinations of devices gave significant jet noise reduction relative to separate-flow baseline nozzles. Inward-flip and alternating-flip core chevrons combined with a straight-chevron fan nozzle exceeded the NASA stretch goal of 3 EPNdB jet noise reduction at typical sideline certification conditions.

Janardan, B. A.↗

DOE OSTI2021

Carbonate clumped isotope analysis (Δ 47 ) of 21 carbonate standards determined via gas‐source isotope‐ratio mass spectrometry on four instrumental configurations using carbonate‐based standardization and multiyear data sets

Rationale Clumped isotope geochemistry examines the pairing or clumping of heavy isotopes in molecules and provides information about the thermodynamic and kinetic controls on their formation. The first clumped isotope measurements of carbonate minerals were first published 15 years ago, and since then, interlaboratory offsets have been observed, and laboratory and community practices for measurement, data analysis, and instrumentation have evolved. Here we briefly review historical and recent developments for measurements, share Tripati Lab practices for four different instrument configurations, test a recently published proposal for carbonate‐based standardization on multiple instruments using multi‐year data sets, and report values for 21 different carbonate standards that allow for recalculations of previously published data sets. Methods We examine data from 4628 standard measurements on Thermo MAT 253 and Nu Perspective IS mass spectrometers, using a common acid bath (90°C) and small‐sample (70°C) individual reaction vessels. Each configuration was investigated by treating some standards as anchors (working standards) and the remainder as unknowns (consistency standards). Results We show that different acid digestion systems and mass spectrometer models yield indistinguishable results when instrument drift is well characterized. For linearity correction, mixed gas‐and‐carbonate standardization or carbonate‐only standardization yields similar results. No difference is observed in the use of three or eight working standards for the construction of transfer functions. Conclusions We show that all configurations yield similar results if instrument drift is robustly characterized and validate a recent proposal for carbonate‐based standardization using large multiyear data sets. Δ 47 values are reported for 21 carbonate standards on both the absolute reference frame (ARF; also refered to as the Carbon Dioxide Equilibrated Scale or CDES) and the new InterCarb‐Carbon Dioxide Equilibrium Scale (I‐CDES) reference frame, facilitating intercomparison of data from a diversity of labs and instrument configurations and restandardization of a broad range of sample sets between 2006, when the first carbonate measurements were published, and the present.

58 GEOSCIENCES↗

NASA NTRSDate not supplied

Optimization of a Parametric Lobe Mixer for Internally Mixed Nozzles

The results of the first phase of an optimization study on a parametric procedurally-generated lobe mixer are presented. This mixer is part of a dual-stream plug nozzle system, designed under NASA’s CST project for use in near-term commercial supersonic applications. Data was obtained numerically using NASA’s in-house CFD code FUN3D and analyzed to determine mixer performance. Phase I of the study examined five independently-variable geometric parameters describing the lobe mixer. Methods of Design of Experiments (DoE) were used to obtain a parametric model to quickly evaluate mixer performance and determine an optimum configuration. Mixers that induced strong axial vorticity and shear layers without causing flow separation were found to perform best, with exit temperature variance highly inversely correlated to mixing effectiveness.

Lobe Mixer↗

NASA NTRSDate not supplied

Optimization of a Parametric Lobe Mixer for Internally Mixed Nozzles

The results of the first phase of an optimization study on a parametric procedurally-generated lobe mixer are presented. This mixer is part of a dual-stream plug nozzle system, designed under NASA’s CST project for use in near-term commercial supersonic applications. Data was obtained numerically using NASA’s in-house CFD code FUN3D and analyzed to determine mixer performance. Phase I of the study examined five independently-variable geometric parameters describing the lobe mixer. Methods of Design of Experiments (DoE) were used to obtain a parametric model to quickly evaluate mixer performance and determine an optimum configuration. Mixers that induced strong axial vorticity and shear layers without causing flow separation were found to perform best, with exit temperature variance highly inversely correlated to mixing effectiveness.

Lobe mixer↗

DOE OSTI2022

Adapting UFF4MOF for Heterometallic Rare-Earth Metal–Organic Frameworks

Heterometallic metal–organic frameworks based on rare-earth metals (RE-MOFs) have potential in a number of applications where energy transfer between nearby metal atoms is required. This observation implies that it is important to understand the level of local mixing that is achieved between metals of different types during synthesis of RE-MOFs. Density functional theory calculations can give quantitative information on the relative energy of different configurations of RE-MOFs, but these calculations cannot be applied to the full range of medium- and long-range orderings that are possible in heterometallic materials. This limitation can be overcome using force field (FF)-based calculations if appropriate FFs are available. In this work, we show that an existing generic FF for MOFs, UFF4MOF, does not accurately predict energies of mixing in heterometallic Nd/Yb MOFs and introduce a modified FF to address this shortcoming. The resulting FF is used to explore metal orderings in large simulation volumes for a Nd/Yb MOF, illustrating the complexities that can arise in the structure of heterometallic RE-MOFs.

36 MATERIALS SCIENCE↗

DOE OSTI2024

The Role of Low-Carbon Fuels and Carbon Capture in Decarbonizing the U.S. Clinker Manufacturing for Cement Production: CO2 Emissions Reduction Potentials

Low-carbon fuels, feedstocks, and energy sources can play a vital role in the decarbonization of clinker production in cement manufacturing. Fuel switching with renewable natural gas, green hydrogen, and biomass can provide a low-carbon energy source for the high-temperature process heat during the pyroprocessing steps of clinker production. However, up to 60% of CO2 emissions from clinker production are attributable to process-related CO2 emissions, which will need the simultaneous implementation of other decarbonization technologies, such as carbon capture. To evaluate the potential of fuel switching and carbon capture technologies in decarbonizing the cement industry, a study of the facility-level CO2 emissions is necessary. This study evaluates the potential for using a single low-carbon fuel as an energy source in clinker production for cement manufacturing compared to conventional clinker production (which uses a range of fuel mixes). In addition, conventional carbon capture (operated with natural gas-based steam for solvent regeneration) and electrified carbon capture configurations were designed and assessed for net-zero emission targets. Carbon emissions reductions with and without biogenic emissions credits were analyzed to ascertain their impact on the overall carbon accounting. Results show that carbon emissions intensity of cement can vary from 571 to 784 kgCO2eq/metric ton of cement without carbon capture and from 166.33 to 438.66 kgCO2eq/metric ton of cement with carbon capture. We find that when biogenic carbon credits are considered, cement production with a sustainably grown biomass as fuel source coupled with conventional carbon capture can lead to a net-negative emission cement (−271 kgCO2eq/metric ton of cement), outperforming an electrified capture design (35 kgCO2eq/metric ton of cement). The carbon accounting for the Scope 1, 2, and biogenic emissions conducted in this study is aimed at helping researchers and industry partners in the cement and concrete sector make an informed decision on the choice of fuel and decarbonization strategy to adopt.

42 ENGINEERING↗

NASA NTRS1958

A Preliminary Investigation of the Performance of a Short-length Turbojet Combustor Using Vaporized Hydrocarbon Fuels

Two short turbojet combustors designed for use with vaporized hydrocarbon fuels were tested in a one-quarter annular duct. The experimental combustors consisted of many small "swirl-can" combustor elements manifolded together. This design approach allowed the secondary mixing zone to be considerably reduced over that of conventional combustors. The over-all combustion lengths, for the two configurations were 13.5 and 11.0 inches, approximately one-half the length of the shortest conventional combustors. These short combustors did not provide combustion efficiencies as high as those for conventional combustors at low pressures. However, over the range of combustor-inlet total-pressures expected in aircraft capable of flight at Mach numbers of 2.5 and above, these short combustors gave very high efficiencies. A combustion efficiency of 97 percent was obtained at a combustor-inlet total-pressure of 25.0 inches of mercury absolute, reference velocity of 120 feet per second, and inlet-air total temperature of 1160 deg R. By proportioning the fuel flow between the manifold rows of can combustor elements, control of the combustor-outlet radial total-temperature profile was demonstrated. Combustor totalpressure loss varied from 0.75 percent of the inlet total pressure at isothermal conditions and a reference velocity of 75 feet per second to 5.5 percent at a total-temperature ratio of 1.8 and a reference velocity of 180 feet per second.

Jones, R. E.↗

NASA NTRS1974

A 727/JT8D-100 series engine exhaust system propulsion performance model test

The results are presented from testing one-eighth scale models of the Pratt and Whitney aircraft reference and Boeing nozzles for the JT8D-100 series mixed flow engines. The objective of the test was to obtain the nozzle velocity and flow coefficients for the reference configurations and compare these with the Boeing configurations which incorporated a longer splitter between the fan and primary flows. A further comparison was made between the JT8D-100 series nozzles and the Boeing JT8D-9/727 production nozzle performance. A statistical analysis was used to compare configurations which showed the performance (velocity coefficient) of the reference and the Boeing configuration was the same for the JT8D-109. It also showed no difference between reference and the Boeing configuration for the JT8D-115 and no difference for the JT8D-117 nozzles. Bypass ratio (match) was shown to be equally dependent on splitter position as on nozzle area within the range investigated. The nozzles were very similar in flow coefficient within an engine family. Excellent profile data was recorded. The effects of swirl on the nozzle performance was examined and found to degrade the velocity and flow coefficients.

Haugan, W. J.↗

NASA NTRS1998

Injector Design Tool Improvements: User's manual for FDNS V.4.5

The major emphasis of the current effort is in the development and validation of an efficient parallel machine computational model, based on the FDNS code, to analyze the fluid dynamics of a wide variety of liquid jet configurations for general liquid rocket engine injection system applications. This model includes physical models for droplet atomization, breakup/coalescence, evaporation, turbulence mixing and gas-phase combustion. Benchmark validation cases for liquid rocket engine chamber combustion conditions will be performed for model validation purpose. Test cases may include shear coaxial, swirl coaxial and impinging injection systems with combinations LOXIH2 or LOXISP-1 propellant injector elements used in rocket engine designs. As a final goal of this project, a well tested parallel CFD performance methodology together with a user's operation description in a final technical report will be reported at the end of the proposed research effort.

Chen, Yen-Sen↗

NASA NTRS1998

Bacteriorhodopsin Material and Film Fabrication Issues for Holographic Applications

We discuss issues associated with bacteriorhodopsin (BR) materials and films that affect optical performance in holographic applications. For the D85N variant, some critical parameters include degree of hydration and recording wavelength. The quantum efficiency of the molecular state transition is observed to be apparently dependent on the illumination wavelength. We explain this effect by modeling the photo-activity of the D85N variant as two competing photocycles between the 9-cis and 13-cis retinal configurations. We are able to determine the pure excited P-state absorbance spectrum from the ground state spectrum and mixed population spectra obtained by bleaching to steady-state conditions.

Downie, John D.↗