Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathode loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Mitigation of Shuttle Effect in Li–S Battery Using a Self-Assembled Ultrathin Molybdenum Disulfide Interlayer

Lithium–sulfur batteries are promising for low-cost and high-energy storage, but their applications are still limited by poor cycling stability owing to soluble lithium polysulfide shuttling during battery operation. Avoiding shuttle effect is challenging but it is essential to avoid active material loss and prevent performance decay. We use an ultrathin layer of MoS 2 with thickness of 10–40 nm, which is 1–2 orders of magnitude thinner than conventional interlayers, for Li–S batteries to mitigate polysulfide shuttling. The MoS2 layer formed by exfoliated nanoflakes is deposited by the scalable liquid-based self-assembly method. With less than 1% of additional weight in the cathode, the MoS 2 interlayer with complete coverage inhibits polysulfide diffusion across the separator and therefore remarkably improves the battery performances. Reversible specific capacity reaches 1010 and 600 mA h g –1 at 0.5 and 2C rates, respectively, which decay slowly over 400 cycles (0.11% per cycle). Moreover, the MoS 2 films with high density of catalytic active flake edges enable high areal sulfur loading up to 10 mg cm –2 and areal capacity up to 9.7 mA h cm –2 at a current density of 3.2 mA cm –2 .

25 ENERGY STORAGE↗

An asymmetric emittance electron source for the GALAXIE dielectric-laser accelerator injector

The GALAXIE project is a program to develop an all-optical, very high field accelerator and undulator integrated SASE FEL system based on dielectric laser-excited structures that support >GV/m fields. These structures are very wide in one direction to allow adequate charge given beam loading considerations, but also having small (subwavelength) apertures in the narrow direction. Such small vertical dimensions yield strict restrictions on the emittance in this direction, while no such constraint exists in the wide transverse direction. However, the overall beam brightness is restricted by the performance requirements on the FEL. To meet these demands, we are studying a very high field gun with a magnetized cathode, yielding a beam with angular momentum content. This beam is then subject to a skew-quad triplet that splits the emittances; this process is reversed to give a round beam after acceleration. This symmetric emittance beam avoids gain-degrading multiple-transverse-mode operation of the FEL, which also demands that the effects of the angular momentum in the beam be mitigated. In this paper we discuss the RF design of an X-band gun to be operated at {approx}200 MV/m peak field giving a 1 pC magnetized beam with unprecedented brightness. We examine the design of the focusing and skew-quad systems, investigating the associated beam dynamics and efficacy of emittance splitting.

43 PARTICLE ACCELERATORS↗

Controlled Nucleation and Growth Process of Li 2 S 2 /Li 2 S in Lithium-Sulfur Batteries

Lithium-sulfur battery is a promising next-generation energy storage system because of its potentially three to five times higher energy density than that of traditional lithium ion batteries. However, the dissolution and precipitation of soluble polysulfides during cycling initiate a series of key-chain reactions that significantly shorten battery life. Herein, we demonstrate that through a simple but effective strategy, significantly improved cycling performance is achieved for high sulfur loading electrodes through controlling the nucleation and precipitation of polysulfieds on the electrode surface. More than 400 or 760 stable cycling are successfully displayed in the cells with locked discharge capacity of 625 mAh g -1 or 500 mAh g -1 , respectively. The nucleation and growth process of dissolved polysulfides has been electrochemically altered to confine the thickness of discharge products passivated on the cathode surface, increasing the utilization rate of sulfur while avoiding severe morphology changes on the electrode. More importantly, the exposure of new lithium metal surface to the S-containing electrolyte is also greatly reduced through this strategy, largely minimizing the anode corrosion caused by polysulfides. This work interlocks the electrode morphologies and its evolution with electrochemical interference to modulate cell performances by using Li-S system as a platform, providing different but critical directions for this community.

25 ENERGY STORAGE↗

Tore Supra LH transmitter upgrade, a new RF driver for the power spectrum

New real time tools have been developed for testing new 700kW/3.7GHz/CW klystrons and for the operations on very long plasma shots. After the commissioning of the 18 series tubes on the high power test bed facility, the installation of the first 8 klystrons in the Tore Supra transmitter and the adjustment tests on load, this upgrade work has been materialized during the last 2010 campaign by a successful operation on the Full Active Multijunction (FAM) C3 antenna, with new performances: 3.5MW/40s on plasma. The RF output power control in amplitude and phase has been improved for a better control of the wave spectrum launched into the plasma. The new klystrons have no modulating anode and the high cathode voltage must be adjusted with the RF input power in order to optimize the RF output power with a minimization of the thermal power losses in the collector. A new phase correction, depending on the 3 RF output power ranges used, has been introduced. The improvements made in 2009 and 2010 on the generic phase loop and the procedures used during the real time tests of the RF transfer functions in amplitude and phase are detailed below. All RF measurements systems, RF safety systems and the RF calibration procedures have been revised in order to have the best consistency, reproducibility and with a measurement error against the calorimetry measurement lower than 10%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Axial mass fraction measurements in a 300kA dense plasma focus

The dynamics and characteristics of the plasma sheath during the axial phase in a ~300 kA, ~2 kJ dense plasma focus using a static gas load of Ne at 1–4 Torr are reported. The sheath, which is driven axially at a constant velocity ~10 5 m/s by the j × B force, is observed using optical imaging, to form an acute angle between the electrodes. This angle becomes more acute (more parallel to the axis) along the rundown. The average sheath thickness nearer the anode is 0.69 ± 0.02 mm and nearer the cathode is 0.95 ± 0.02 mm. The sheath total mass increases from 1 ± 0.02 μg to 6 ± 0.02 μg over the pressure range of 1–4 Torr. However, the mass fraction (defined as the sheath mass/total mass of cold gas between the electrodes) decreases from 7% to 5%. In addition, the steeper the plasma sheath, the more mass is lost from the sheath, which is consistent with radial and axial motion. Lastly, experimental results are compared to the Lee code when 100% of the current drives the axial and radial phase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Application of a temporal multiscale method for efficient simulation of degradation in PEM Water Electrolysis under dynamic operating conditions

Hydrogen is emerging as a vital energy carrier, driven by the need to reduce carbon emissions. Proton Electrolyte Membrane Water Electrolysis (PEMWE) enables hydrogen production under fluctuating renewable power conditions but requires improved understanding and stability of the anode catalyst layer under dynamic operating conditions, especially with low noble metal loadings. Long-term degradation experiments are both time-consuming and costly; therefore, a systematic, model-aided approach is essential. In the present work, a temporal multiscale method is applied to reduce the computational effort of simulating long-term degradation processes in PEMWE, with an exemplary focus on catalyst dissolution. A mechanistic model incorporating the oxygen evolution reaction, catalyst dissolution, and hydrogen permeation from the cathode to the anode was hypothesized and implemented. In this way, the local periodicity of transport and reaction processes in dynamic PEMWE operation, which influence the gradual degradation of the catalyst layer, is captured. The temporal multiscale method significantly reduces the computational effort of simulation, decreasing processing time from hours to mere minutes. This efficiency gain is attributed to the limited evolution of Slow-Scale variables during each period of time P of the Fast-Scale variables. Consequently, simulation is required only until local periodicity is achieved within each Slow-Scale time step. Hence, the fully resolved dynamic problem is decoupled into these two scales, employing a heterogeneous multiscale technique. The developed approach effectively accelerates parameter estimation and predictive simulations, supporting systematic modeling of PEMWE degradation under dynamic conditions.

08 HYDROGEN↗

Enhanced Densification of SDC Barrier Layers

This technical report explores the Enhanced Densification of SCD Barrier Layers A samaria-doped ceria (SDC) barrier layer separates the lanthanum strontium cobalt ferrite (LSCF) cathode from the yttria-stabilized zirconia (YSZ) electrolyte in a solid oxide fuel cell (SOFC) to prevent the formation of electrically resistive interfacial SrZrO 3 layers that arise from the reaction of Sr from the LSCF with Zr from the YSZ. However, the sintering temperature of this SDC layer must be limited to 1200°C to avoid extensive interdiffusion between SDC and YSZ to form a resistive CeO 2 -ZrO 2 solid solution. Therefore, the conventional SDC layer is often porous and therefore not as impervious to Sr-diffusion as would be desired. In the pursuit of improved SOFC performance, efforts have been directed toward increasing the density of the SDC barrier layer without increasing the sintering temperature. The density of the SDC barrier layer can be greatly increased through small amounts of Cu-doping of the SDC powder together with increased solids loading and use of an appropriate binder system in the screen print ink. However, the resulting performance of cells with these barrier layers did not exhibit the expected increase in accordance with that achieved with the prototypical PLD SDC layer. It was determined by XRD that increased sinterability of the SDC also results in increased interdiffusivity between the SDC and YSZ, resulting in formation of a highly resistive solid solution.

30 DIRECT ENERGY CONVERSION↗

Incorporating Solvate and Solid Electrolytes for All‐Solid‐State Li 2 S Batteries with High Capacity and Long Cycle Life

Abstract The development of all‐solid‐state lithium–sulfur batteries is hindered by the poor interfacial properties at solid electrolyte (SE)/electrode interfaces. The interface is modified by employing the highly concentrated solvate electrolyte, (MeCN) 2 −LiTFSI:TTE, as an interlayer material at the electrolyte/electrode interfaces. The incorporation of an interlayer significantly improves the cycling performance of solid‐state Li 2 S batteries compared to the bare counterpart, exhibiting a specific capacity of 760 mAh g −1 at cycle 100 (330 mAh g −1 for the bare cell). Electrochemical impedance spectroscopy shows that the interfacial resistance of the interlayer‐modified cell gradually decreases as a function of cycle number, while the impedance of the bare cell remains almost constant. Cross‐section scanning electron microscopy (SEM)/ energy dispersive X‐ray spectroscopy (EDS) measurements on the interlayer‐modified cell confirm the permeation of solvate into the cathode and the SE with electrochemical cycling, which is related to the decrease in cell impedance. In order to mimic the full permeation of the solvate across the entire cell, the solvate is directly mixed with the SE to form a “solvSEM” electrolyte. The hybrid Li 2 S cell using a solvSEM electrolyte exhibits superior cycling performance compared to the solid‐state cells, in terms of Li 2 S loading, Li 2 S utilization, and cycling stability. The improved performance is due to the favorable ionic contact at the battery interfaces.

Shin, Minjeong↗

Filamentation and Self-Focusing of Electron Beams in Vacuum and Gas Diodes

In this paper, we experimentally studied pulsed electron beams with a high local density. The conditions in which the energy density cumulation is observed during the interaction of electrons with the anode are shown to develop in vacuum and gas diodes at nanosecond and subnanosecond durations of a beam current pulse and a decrease in the interelectrode gap. The average electron energy in filamentation and self-focusing of an electron beam in a vacuum diode of an accelerator at a current of ~2 kA and a no-load voltage of ~400 kV was established to be 50–100 keV while the energy density was 10{sup 9}–10{sup 10} J/cm{sup 3}. It is confirmed that the beam current density in a gas diode can exceed 1 kA/cm{sup 2}. It is hypothesized that superdense electron beams in vacuum and gas diodes are formed as a result of avalanche multiplication of runaway electrons in the cathode–anode gap plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interdigitated power connector

An electrical connector carries large amounts of electrical current between two circuit boards with low resistance and low self-inductance by means of an interdigitated anode and cathode, thereby providing low dynamic voltage loss. The connector also may include, near where power will be consumed, an interposer board with on-board capacitance to provide even lower dynamic voltage loss. The connector has application to delivering low-voltage, high-current power from a power supply on a first board to electronics on a second board: the low resistance provides low voltage drop for a load current that is constant, while the low inductance and the capacitors provide low voltage fluctuation for a load current that changes. These issues are of great importance, for example, in designing high-performance computers.

Coteus, Paul W.↗

Optimization of mesoporous carbon structures for lithium–sulfur battery applications

Mesoporous carbon (MC) with tunable pore sizes (22nm, 12nm, 7nm, and 3nm) and pore volumes (from 1.3 to 4.8 cc/g) containing sulfur inside the pores were systematically studied as mesoporous carbon-sulfur (MCS) composite electrodes for Li-S batteries. Investigation on these MCS composites reveals that the pore structure has no influence on the battery performance at full sulfur loading conditions (the pore volume is fully filled by sulfur) but the maximum sulfur loading capability is higher for MC with larger pore volume. MC with large pore volumes, partial sulfur filling (part of the pore volume left unfilled), and surface modification, can have reasonably high sulfur loading, improved electrical and ionic contacts of sulfur with MC and with electrolytes, which subsequently promotes the battery performance. An initial capacity of ~1250 mAh/g (based on sulfur) and 650 mAh/g capacity retention over 100 cycles were obtained with 50 wt% sulfur loading in the MC with 22nm pore size (4.8 cc/g). When the surface of MCS was coated with Clevios P to reduce the dissolve of polysulfide anions in electrolytes, it exhibits a high initial discharge capacity of ~1390 mAh/g and improved cycling stability with capacity retention of ~840 mAh/g over 100 cycles. The reported correlation among the structure, sulfur filling, surface modification and the electrochemical performance of the MCS composite cathodes provides guidance in designing new electrodes for lithium-sulfur batteries

25 ENERGY STORAGE↗

Experimental Investigations into U/TRU Recovery using a Liquid Cadmium Cathode and Salt Containing High Rare Earth Concentrations

Experimental Investigations into U/TRU Recovery using a Liquid Cadmium Cathode and Salt Containing High Rare Earth Concentrations Shelly X. Li, Steven D. Herrmann, and Michael F. Simpson Pyroprocessing Technology Department Idaho National Laboratory P.O. Box 1625, Idaho Falls, ID 83415 USA Abstract - A series of six bench-scale liquid cadmium cathode (LCC) tests was performed to obtain basic separation data with focus on the behavior of rare earth elements. The electrolyte used for the tests was a mixed salt from the Mk-IV and Mk-V electrorefiners, in which spent metal fuels from Experimental Breeder Reactor-II (EBR-II) had been processed. Rare earth (RE) chlorides, such as NdCl3, CeCl3, LaCl3, PrCl3, SmCl3, and YCl3, were spiked into the salt prior to the first test to create an extreme case for investigating rare earth contamination of the actinides collected by a LCC. For the first two LCC tests, an alloy with the nominal composition of 41U-30Pu-5Am-3Np-20Zr-1RE was loaded into the anode baskets as the feed material. The anode feed material for Runs 3 to 6 was spent ternary fuel (U-19Pu-10Zr). The Pu/U ratio in the salt varied from 0.6 to 1.3. Chemical and radiochemical analytical results confirmed that U and transuranics can be collected into the LCC as a group under the given run conditions. The RE contamination level in the LCC product was up to 6.7 wt% of the total metal collected. The detailed data for partitioning of actinides and REs in the salt and Cd phases are reported in the paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A rejuvenation process to enhance the durability of low Pt loaded polymer electrolyte membrane fuel cells

Here, an effective method to enhance the durability of polymer electrolyte membrane fuel cells (PEMFCs) is reported. PEMFC performance loss is mitigated by exposing the electrodes of fuel cells to dry nitrogen gas periodically at high temperature. This method extends the lifetime of fuel cells significantly compared to their non-treated counterparts. The impact of treatment temperature and exposure time on PEMFC durability is reported, using potential cycling accelerated stress tests. The enhanced durability is attributed to the suppression of “ionomer relaxation” that occurs under the nearly water saturated operating conditions of a PEMFC cathode.

30 DIRECT ENERGY CONVERSION↗

Resolving Electrode Morphology’s Impact on Platinum Group Metal-Free Cathode Performance Using Nano-CT of 3D Hierarchical Pore and Ionomer Distribution

This paper reports on the characterization of polymer electrolyte fuel cell (PEFC) cathodes featuring a platinum group metal-free (PGM-free) catalyst using nano-scale resolution X-ray computed tomography (nano-CT) and morphological analysis. PGM-free PEFC cathodes have gained significant interest in the past decade since they have the potential to dramatically reduce PEFC costs by eliminating the large platinum (Pt) raw material cost. However, several challenges remain before they are commercially viable. Since these catalysts have lower volumetric activity, the PGM-free cathodes are thicker and are subject to increased gas and proton transport resistances that reduce the performance. To better understand the efficacy of the catalyst and improve electrode performance, a detailed understanding the correlation between electrode fabrication, morphology, and performance is crucial. In this work, the pore/solid structure and the ionomer distribution was resolved in three dimensions (3D) using nano-CT for three PGM-free electrodes of varying Nafion® loading. The associated transport properties were evaluated from pore/particlescale simulations within the nano-CT imaged structure. These characterizations are then used to elucidate the microstructural origins of the dramatic changes in fuel cell performance with varying Nafion® ionomer loading. We show that this is primarily a result of distinct changes in ionomer’s spatial distribution. The significant impact of electrode morphology on performance highlights the importance of PGM-free electrode development in concert with efforts to improve catalyst activity and durability.

42 ENGINEERING↗

High-Platinum-Content Catalysts on Atomically Dispersed and Nitrogen Coordinated Single Manganese Site Carbons for Heavy-Duty Fuel Cells

Fuel cells for heavy-duty vehicles (HDVs) have attracted considerable attention because of their unique scalability, better fuel economy, the less demand for hydrogen refilling infrastructure. However, the potential application requires more stringent fuel cell durability up to 25,000 h. Membrane electrode assemblies (MEAs) made from platinum group metal (PGM) catalyst with relatively high loading 0.3 mgPt cm –2 play a crucial role in ensuring high-power and long-term durability. Integrating fine PGM nanoparticles and robust carbon support with strengthened interactions is critical for improving MEA performance and durability. Herein, a unique atomically dispersed and nitrogen coordinated single Mn site-rich carbon (M–N–C) support was developed for high content (40 wt%) platinum catalysts for the oxygen reduction reaction (ORR) cathode with reduced thickness. Compared with two controls studied in this work (e.g., a porous graphitic carbon-supported Pt and a commercial TKK Pt/C catalysts), the Pt (40 wt%)/Mn–N–C catalyst exhibited much enhanced catalytic activity and stability for the ORR in both aqueous acidic electrolyte and polymer electrolyte-based MEA. Here, we carefully elucidated the—role of the Mn–N–C support in promoting Pt catalyst concerning its high surface area, partially graphitic structure, and nitrogen dopants, providing better Pt nanoparticle dispersion, and strengthened interactions between Pt and carbon. Consequently, the MEA from the Pt (40 wt%)/Mn–N–C catalyst generated a 1.61 A cm –2 at 0.7 V based on HDV conditions (0.2 mgPt cm –2 and 250 kPa air). More importantly, the MEA is highly durable and can retain 1.31 A cm –2 at 0.7 V after 30,000 voltage cycles (~19% loss), surpassing the commercial Pt/C catalyst (loss of ~56%). Therefore, the Mn–N–C carbon-supported Pt catalyst holds a great promise to meet the challenging DOE target (1.07 A cm –2 at 0.7 V after 150,000 cycles) for HDVs.

25 ENERGY STORAGE↗

R&D ERL: Vacuum

The ERL Vacuum systems are depicted in a figure. ERL has eight vacuum volumes with various sets of requirements. A summary of vacuum related requirements is provided in a table. Five of the eight volumes comprise the electron beamline. They are the 5-cell Superconducting RF Cavity, Superconducting e-gun, injection, loop and beam dump. Two vacuum regions are the individual cryostats insulating the 5-cell Superconducting RF Cavity and the Superconducting e-gun structures. The last ERL vacuum volume not shown in the schematic is the laser transport line. The beamline vacuum regions are separated by electropneumatic gate valves. The beam dump is common with loop beamline but is considered a separate volume due to geometry and requirements. Vacuum in the 5-cell SRF cavity is maintained in the {approx}10{sup -9} torr range at room temperature by two 20 l/s ion pumps and in the e-gun SRF cavity by one 60 l/s ion pump. Vacuum in the SRF cavities operated at 2{sup o}K is reduced to low 10{sup -11} torr via cryopumping of the cavity walls. The cathode of the e-gun must be protected from poisoning, which can occur if vacuum adjacent to the e-gun in the injection line exceeds 10-11 torr range in the injection warm beamline near the e-gun exit. The vacuum requirements for beam operation in the loop and beam dump are 10-9 torr range. The beamlines are evacuated from atmospheric pressure to high vacuum level with a particulate free, oil free turbomolecular pumping cart. 25 l/s shielded ion pumps distributed throughout the beamlines maintain the vacuum requirement. Due to the more demanding vacuum requirement of the injection beamline proximate to the e-gun, a vacuum bakeout of the injection beamline is required. In addition, two 200 l/s diode ion pumps and supplemental pumping provided by titanium sublimation pumps are installed in the injection line just beyond the exit of the e-gun. Due to expected gas load a similar pumping arrangement is planned for the beam dump. The cryostat vacuum thermally insulating the SRF cavities need only reduce the convective heat load such that heat loss is primarily radiation through several layers of multi-layer insulation and conductive end-losses which are contained by 5{sup o}K thermal transitions. Prior to cool down rough vacuum {approx}10{sup -5} torr range is established and maintained by a dedicated turbomolecular pump station. Cryopumping by the cold mass and heat shields reduces the insulating vacuum to 10{sup -7} torr range after cool down.

43 PARTICLE ACCELERATORS↗