Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 deg to 90 deg. 1: Influence of airplane components for model D

The influence of airplane components, as well as wing location and tail length, on the rotational flow aerodynamics is discussed for a 1/6 scale general aviation airplane model. The airplane was tested in a built-up fashion (i.e., body, body-wing, body-wing-vertical, etc.) in the presence of two wing locations and two body lengths. Data were measured, using a rotary balance, over an angle-of-attack range of 8 deg to 90 deg, and for clockwise and counter-clockwise rotations covering an omega b/2V range of 0 to 0.9.

Ralston, J.↗
NASA NTRS1972

Jet effects on the drag of conical afterbodies at supersonic speeds

A parametric investigation has been conducted to determine the jet effects on the boattail drag of nozzles with truncated conical afterbodies. The boattail drag for nozzle configurations with boattail angles of 3 deg, 5 deg, and 10 deg and ratios of boattail length to maximum diameter of 1.0, 0.8, and 0.6 was compared for the jet-off condition and for a wide range of jet pressure ratios. A nozzle configuration with a circular-arc boattail was tested also. The tests were run at Mach numbers of 1.83 and 2.20 with the model at an angle of attack of 0 deg.

Compton, W. B., III↗
NASA NTRS1973

Supersonic Experiments on Dynamic Cross-Derivatives Due to Pitching and Yawing of Aircraft-Like Vehicles

A wind tunnel apparatus has been developed and constructed for the determination of moment cross-derivatives due to pitching and yawing on models at moderate angles of attack and sideslip. The apparatus can also be used to determine the direct moment derivatives in pitch and yaw. Experimental results were obtained at Mach 2 on a cone-wing-fin configuration at angles of attack and sideslip up to 15. Although at small values of these angles the cross-derivatives were always negligibly small, measureable effects were sometimes observed, at all angles of attack included in this investigation (i.e. up to 15 deg), when the angle of sideslip was 10 deg or 15 deg.

Orlik-Ruckemann, K. J.↗
NASA NTRS1973

Evaluation of experimental flow properties in the wake of a Viking '75 entry vehicle.

An experimental investigation has been conducted to obtain the flow properties in the wake of a model of the Viking '75 entry vehicle. Data are presented for the model at several angles of attack at free-stream Mach numbers from 0.2 to 3.95. The characteristics of the wake flow field are discussed and results are shown to demonstrate the significant variation of wake center-line flow properties in the transonic speed range, the shift in wake profiles with change in angle of attack, and the similarity exhibited by the velocity profiles across the wake.

Campbell, J. F.↗
NASA NTRS1974

System design optimization for a Mars-roving vehicle and perturbed-optimal solutions in nonlinear programming

Work in two somewhat distinct areas is presented. First, the optimal system design problem for a Mars-roving vehicle is attacked by creating static system models and a system evaluation function and optimizing via nonlinear programming techniques. The second area concerns the problem of perturbed-optimal solutions. Given an initial perturbation in an element of the solution to a nonlinear programming problem, a linear method is determined to approximate the optimal readjustments of the other elements of the solution. Then, the sensitivity of the Mars rover designs is described by application of this method.

Pavarini, C.↗
NASA NTRS1975

Development of a remote digital augmentation system and application to a remotely piloted research vehicle

A cost-effective approach to flight testing advanced control concepts with remotely piloted vehicles is described. The approach utilizes a ground based digital computer coupled to the remotely piloted vehicle's motion sensors and control surface actuators through telemetry links to provide high bandwidth feedback control. The system was applied to the control of an unmanned 3/8-scale model of the F-15 airplane. The model was remotely augmented; that is, the F-15 mechanical and control augmentation flight control systems were simulated by the ground-based computer, rather than being in the vehicle itself. The results of flight tests of the model at high angles of attack are discussed.

Edwards, J. W.↗
NASA NTRS1975

Low-speed upwash interference on a transport model in a rectangular slotted-wall wind tunnel

A study was made of the upwash interference caused by the wind tunnel walls at a Mach number of 0.20. The wind tunnel has slotted horizontal walls and solid vertical walls and the wind tunnel model is a wing-fuselage combination typical of a short take-off and landing (STOL) transport. Measurements were made of the model forces and angle of attack. The experimental results are compared to theoretical solutions for the upwash interference. This comparison enabled an indirect determination of one of the constants in the slotted wall boundary condition. The magnitude of the experimental upwash interference is also compared to the accuracy of the data. This comparison indicates that it is difficult to make definite conclusions based on the experimental data. Suggestions are made for future research which could provide a practical means of accurately determining the wall-interference velocities in wind tunnels with rigid slotted walls.

Mann, M. J.↗
NASA NTRS1975

High-attitude low-speed static aerodynamic characteristics of an F-4D fighter airplane model with leading edge slats

An investigation was conducted to determine the effects of two-position leading edge slats on the low speed aerodynamic characteristics of a swept wing twin-jet supersonic fighter airplane model at high angle of attack and various Reynolds numbers. The investigation was performed at a Mach number of 0.20 over a range of angle of attack from 19 deg to 90 deg and angles of slideslip from -10 deg to 30 deg and Reynolds numbers from 1.97 to 13.12 million per meter.

Monfort, J. C.↗
NASA NTRS1981

Curved-flow, rolling-flow, and oscillatory pure-yawing wind-tunnel test methods for determination of dynamic stability derivatives

Dynamic stability derivatives are evaluated on the basis of rolling-flow, curved-flow and snaking tests. Attention is given to the hardware associated with curved-flow, rolling-flow and oscillatory pure-yawing wind-tunnel tests. It is found that the snaking technique, when combined with linear- and forced-oscillation methods, yields an important method for evaluating beta derivatives for current configurations at high angles of attack. Since the rolling flow model is fixed during testing, forced oscillations may be imparted to the model, permitting the measurement of damping and cross-derivatives. These results, when coupled with basic rolling-flow or rotary-balance data, yield a highly accurate mathematical model for studies of incipient spin and spin entry.

Chambers, J. R.↗
NASA NTRS1981

Determination of wind tunnel constraint effects by a unified pressure signature method. Part 2: Application to jet-in-crossflow

The development of an improved jet-in-crossflow model for estimating wind tunnel blockage and angle-of-attack interference is described. Experiments showed that the simpler existing models fall seriously short of representing far-field flows properly. A new, vortex-source-doublet (VSD) model was therefore developed which employs curved trajectories and experimentally-based singularity strengths. The new model is consistent with existing and new experimental data and it predicts tunnel wall (i.e. far-field) pressures properly. It is implemented as a preprocessor to the wall-pressure-signature-based tunnel interference predictor. The supporting experiments and theoretical studies revealed some new results. Comparative flow field measurements with 1-inch "free-air" and 3-inch impinging jets showed that vortex penetration into the flow, in diameters, was almost unaltered until 'hard' impingement occurred. In modeling impinging cases, a 'plume redirection' term was introduced which is apparently absent in previous models. The effects of this term were found to be very significant.

Hackett, J. E.↗
NASA NTRS1982

Calculation of the flow field including boundary layer effects for supersonic mixed compression inlets at angles of attack

The flow field in supersonic mixed compression aircraft inlets at angle of attack is calculated. A zonal modeling technique is employed to obtain the solution which divides the flow field into different computational regions. The computational regions consist of a supersonic core flow, boundary layer flows adjacent to both the forebody/centerbody and cowl contours, and flow in the shock wave boundary layer interaction regions. The zonal modeling analysis is described and some computational results are presented. The governing equations for the supersonic core flow form a hyperbolic system of partial differential equations. The equations for the characteristic surfaces and the compatibility equations applicable along these surfaces are derived. The characteristic surfaces are the stream surfaces, which are surfaces composed of streamlines, and the wave surfaces, which are surfaces tangent to a Mach conoid. The compatibility equations are expressed as directional derivatives along streamlines and bicharacteristics, which are the lines of tangency between a wave surface and a Mach conoid.

Vadyak, J.↗
NASA NTRS1983

Hypersonic shock tunnel heat transfer tests of the Space Shuttle SILTS pod configuration

Heat transfer measurements have been made on a 0.0175-scale NASA Space Shuttle orbiter model having a simulated SILTS (Shuttle Infrared Leeside Temperature Sensor) pod on top of the vertical tail. Heat transfer distributions were measured both on the pod and on the vertical tail. The test program covered Mach numbers of 8, 11 and 16 in air, at Reynolds numbers from 100,000 to 18 million, based on model length. The angle of attack ranged from 30 deg to 40 deg at sideslip angles from -2 to +2 deg. Data were obtained with 92 thin film assistance thermometers located on the SILTS pod and on the upper 30 percent of the vertical tail. Heat transfer rates measured on the vertical tail show good agreement with flight data obtained from missions STS-1, -2 and -3. The variation of heat transfer to the pod with Reynolds number, Mach number and angle of attack is discussed.

Wittliff, C. E.↗
NASA NTRS1986

Method for the prediction of the installation aerodynamics of a propfan at subsonic speeds: User manual

This document is the user's guide for the method developed earlier for predicting the slipstream wing interaction at subsonic speeds. The analysis involves a subsonic panel code (HESS code) modified to handle the propeller onset flow. The propfan slipstream effects are superimposed on the normal flow boundary condition and are applied over the surface washed by the slipstream. The effects of the propeller slipstream are to increase the axial induced velocity, tangential velocity, and a total pressure rise in the wake of the propeller. Principles based on blade performance theory, momentum theory, and vortex theory were used to evaluate the slipstream effects. The code can be applied to any arbitrary three dimensional geometry, expressed in the form of HESS input format. The code can handle a propeller alone configuration or a propeller/nacelle/airframe configuration, operating up to high subcritical Mach numbers over a range of angles of attack. Inclusion of a viscous modelling is briefly outlined. Wind tunnel results/theory comparisons are included as examples for the application of the code to a generic supercritical wing/overwing Nacelle with a powered propfan. A sample input/output listing is provided.

Chandrasekaran, B.↗
NASA NTRS1985

Steady and unsteady incompressible free-wake analysis

The flows around highly sweptback wings and bodies of revolution at high angle of attack are described, and inviscid model approximations and mathematical formulation of the problem are given to steady and unsteady incompressible flows. A general presentation of the methods of solution is given, with emphasis on current computational techniques. Detailed descriptions of the nonlinear vortex-lattice and vortex-panel techniques are presented to show how the boundary conditions are enforced using iteration. Typical numerical results are compared with the available experimental data.

Kandil, O. A.↗
NASA NTRS1987

Design and fabrication requirements for low noise supersonic/hypersonic wind tunnels

A schematic diagram of the new proposed Supersonic Low Disturbance Tunnel (SLDT) is shown. Large width two dimensional rapid expansion nozzles guarantee wide quiet test cores that are well suited for testing models at large angle of attack and for swept wings. Hence, this type of nozzle will be operated first in the new proposed large scale SLDT. Test results indicate that the surface finish of pilot nozzles is critical. The local roughness Reynolds number criteria R sub k is approx. = 10 will be used to specify allowable roughness on new pilot nozzles and the new proposed tunnel. Experimental data and calculations for M = 3.0, 3.5, and 5.0 nozzles give N-factors from 6 to 10 for transition caused by Goertler vortices. The use of N is approx. = 9.0 for the Goertler instability predicts quiet test cores in the new M = 3.5 and M = 6.0 axisymmetric long pilot nozzles that are 3 to 4 times longer than observed in the test nozzles to date. The new nozzles utilize a region of radial flow which moves the inflection point far downstream and delays the onset and amplification of the Goertler vortices.

Beckwith, Ivan E.↗
NASA NTRS1989

Report from ionospheric science

The general strategy to advance knowledge of the ionospheric component of the solar terrestrial system should consist of a three pronged attack on the problem. Ionospheric models should be refined by utilization of existing and new data bases. The data generated in the future should emphasize spatial and temporal gradients and their relation to other events in the solar terrestrial system. In parallel with the improvement in modeling, it will be necessary to initiate a program of advanced instrument development. In particular, emphasis should be placed on the area of improved imaging techniques. The third general activity to be supported should be active experiments related to a better understanding of the basic physics of interactions occurring in the ionospheric environment. These strategies are briefly discussed.

Raitt, W. J.↗
NASA NTRS1992

Improvements to the missile aerodynamic prediction code DEMON3

The computer program DEMON3 was developed for the aerodynamic analysis of nonconventional supersonic configurations comprising a body with noncircular cross section and up to two wing or fin sections. Within a wing or fin section, the lifting surfaces may be cruciform, triform, planar, or low profile layouts; the planforms of the lifting surfaces allow for breaks in sweep. The body and fin sections are modeled by triplet and constant u-velocity panels, respectively, accounting for mutual body-fin interference. Fin thickness effects are included for the use of supersonic planar source panels. One of the unique features of DEMON3 is the modeling of high angle of attack vortical effects associated with the lifting surfaces and the body. In addition, shock expansion and Newtonian pressure calculation methods can be optionally engaged. These two dimensional nonlinear methods are augmented by aerodynamic interference determined from the linear panel methods. Depending on the geometric details of the body, the DEMON3 program can be used to analyze nonconventional configurations at angles of attack up to 25 degrees for Mach numbers from 1.1 to 6. Calculative results and comparisons with experimental data demonstrate the capabilities of DEMON3. Limitations and deficiencies are listed.

Dillenius, Marnix F. E.↗
NASA NTRS1954

Experimental Effects of Propulsive Jets and Afterbody Configurations on the Zero-lift Drag of Bodies of Revolution at a Mach Number of 1.59

The present investigation was made at a free-stream Mach number of 1.59 to compare the afterbody drags to a series of conical boattailed models at zero angle of attack. Afterbody drags were obtained for both the power-off and the power-on conditions. Power-on drags were obtained as a function of afterbody fineness ratio, jet pressure ratio and divergence, and jet Mach number.

De Moraes, Carlos A↗