Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “annular”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Performance of an Experimental Annular Turbojet Combustor with Methane and Propane

Combustion efficiencies obtained with gaseous methane were compared with reported data obtained with gaseous propane for the same experimental combustor configuration. The combustion efficiencies obtained with methane were 98, 91, and 77 percent at simulated flight altitudes of 56,000, 70,000 and 80,000 feet, corresponding to combustor inlet-air pressures from 15 to 5 inches of mercury absolute. Combustion efficiencies with propane were equivalent to those with methane up to a simulated altitude of 70,000 feet. At the most severe conditions investigated propane operated with a higher efficiency and over a wider range of fuel-air ratio than methane.

Norgren, Carl T↗
NASA NTRS1931

The Design and Development of an Automatic Injection Valve with an Annular Orifice of Varying Area

The purpose of this investigation was to provide an automatic injection valve of simple construction which would produce a finely atomized oil spray of broad cone angle and would fulfill the requirements of fuel injection in aircraft oil engines. The injection valve designed has only six parts - i. e., two concentric nozzle tubes flared at one end, two body parts, and two nuts. Analysis and engine tests indicate that the fuel spray from this type of injection valve has characteristics which reduce the time lag of autoignition and promote efficient combustion in high-speed oil engines.

Joachim, William F↗
NASA NTRS1949

Investigation of Altitude Performance of AN-F-58 Fuels in Annular Combustor of J34-WE-22 Engine

An investigation was conducted in the combustor of a 3000-pound-thrust turbojet engine to determine the altitude performance characteristics of AN-F-58 fuels. Three fuels conforming to AN-F-58 specification were prepared in order to determine the influence of boiling-temperature range and aromatic content on altitude performance. The performance of the three AN-F-58 fuels was compared with the performance of AN-F-48 (grade 100/130) fuel in the range of simulated altitudes from 20,000 to 55,000 feet, corrected engine speeds from 6000to 12,500 rpm, and flight Mach numbers of 0.2 and 0.6.

Tischler, Adelbert O↗
NASA NTRS1994

Hotfire testing of a SSME HPOTP with an annular hydrostatic bearing

A new fluid film bearing package has been tested in the Space Shuttle Main Engine (SSME) High Pressure Oxygen Turbopump (HPOTP). This fluid film element functions as both the pump end bearing and the preburner pump rear wear ring seal. Most importantly, it replaces a duplex ball bearing package which has been the primary life limiting component in the turbopump. The design and predicted performance of the turbopump are reviewed. Results are presented for measured pump and bearing performance during testing on the NASA Technology Test Bed (TTB) Engine located at MSFC. The most significant results were obtained from proximity probes located in the bearing bore which revealed large subsynchronous precession at ten percent of shaft speed during engine start which subsided prior to mainstage power levels and reappeared during engine shutdown at equivalent power levels below 65% of nominal. This phenomenon has been attributed to rotating stall in the diffuser. The proximity probes also revealed the location of the bearing in the bore for different operating speeds. Pump vibration characteristics were improved as compared to pumps tested with ball bearings. After seven starts and more than 700 seconds of testing, the pump showed no signs of performance degradation.

Nolan, Steven A.↗
NASA NTRS1994

Compliant Metal Enhanced Convection Cooled Reverse-Flow Annular Combustor

A joint Army/NASA program was conducted to design, fabricate, and test an advanced, reverse-flow, small gas turbine combustor using a compliant metal enhanced (CME) convection wall cooling concept. The objectives of this effort were to develop a design method (basic design data base and analysis) for the CME cooling technique and tben demonstrate its application to an advanced cycle, small, reverse-flow combustor with 3000 F (1922 K) burner outlet temperature (BOT). The CME concept offers significant improvements in wall cooling effectiveness resulting in a large reduction in cooling air requirements. Therefore, more air is available for control of burner outlet temperature pattern in addition to the benefit of improved efficiency, reduced emissions, and smoke levels. Rig test results demonstrated the benefits and viability of the CME concept meeting or exceeding the aerothermal performance and liner wall temperature characteristics of similar lower temperature-rise combustors, achieving 0.15 pattern factor at 3000 F (1922 K) BOT, while utilizing approximately 80 percent less cooling air than conventional, film-cooled combustion systems.

Paskin, Marc D.↗
NASA NTRS1994

Planar Rayleigh scattering and laser-induced fluorescence for visualization of a hot, Mach 2 annular air jet

Planar Rayleigh scattering (PRS) and planar laser-induced fluorescence (PLIF) were used to investigate the vitiated air component of a coaxial hydrogen/vitiated air nonpremixed turbulent jet flame that is ejected at a Mach number of 2. All experiments were performed with a xenon chloride tunable excimer laser. Planar information for both techniques was obtained using laser sheets 6 cm high, 5 cm wide, and 300 micron thick. In this flow field, the effective Rayleigh cross section of the components in the vitiated air was assumed to be independent of composition. Therefore, the PRS technique produced signals which were proportional to total density. When the flow field was assumed to be at a known and uniform pressure, the PRS signal data for the vitiated air could be converted to temperature information. Also, PLIF images were generated by probing the OH molecule. These images contain striation patterns attributed to small localized instantaneous temperature nonuniformities. The results from the PLIF and PRS techniques were used to show that this flow field contains a nongaseous component, most likely liquid water that can be reduced by increasing the settling chamber wall temperature.

Balla, R. Jeffrey↗