SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Wind-tunnel tests have been conducted at Mach numbers of 0.85, 0.88, and 0.90 to determine the aerodynamic load distribution for the 39 deg swept-wing configuration of a variable-wing-sweep fighter airplane with a NASA supercritical airfoil. Chordwise pressure distributions were measured at two wing stations. Also measured were the overall longitudinal aerodynamic force and moment characteristics and the buffet characteristics. The analysis indicates that localized regions of shock-induced flow separation may exist on the rearward portions of the supercritical wing at high subsonic speeds, and caution must be exercised in the prediction of buffet onset when using variations in trailing-edge pressure coefficients at isolated locations.
An investigation was performed in the Langley Unitary Plan wind tunnel to determine the aerodynamic characteristics of a model of a 45 deg swept-wing fighter airplane, and to determine the loads on attached stores and detached missiles in the presence of the model. Also included was a determination of aileron-spoiler effectiveness, aileron hinge moments, and the effects of wing modifications on model aerodynamic characteristics. Tests were performed at Mach numbers of 1.57, 1.87, 2.16, and 2.53. The Reynolds numbers for the tests, based on the mean aerodynamic chord of the wing, varied from about 0.9 x 10(exp 6) to 5 x 10(exp 6). The results are presented with minimum analysis.
The statis stability and control characteristics and air loads on the wing and aileron of a 0.09 scale model of an airplane with a 17 percent thick supercritical wing were investigated. The longitudinal aerodynamic characteristics were determined over a lift coefficient range sufficiently high to induce buffet onset at Mach numbers from 0.30 to 0.80. In addition, the lateral aerodynamic characteristics were determined as a function of sideslip angle and angle of attack at selected Mach numbers.
The performances of a derivative concept of a 1985 STOL tilt rotor transport, and of a second concept having a complex mechanical flap system similar to a short field B737 aircraft were compared for a 370 kilometer (200 nautical mile) short haul mission. The flap system of the latter allowed lift to be shifted from the rotor system to the wing, permitting a 26 percent reduction in dynamic component weight, while also permitting the use of a smaller wing. The wing and disc loading of this concept were 5746 (120 psf) and 1915 (40 psf) newtons per square meter, respectively, while the wing and disc loading of the derivative concept were 4788 (100 psf) and 1197 (25 psf) newtons per square meter, respectively. The high lift wing tilt rotor showed slightly improved fuel usage over its entire operating range and about 6 to 8 percent improvement in direct operating costs, resulting from its improved cruise efficiency and reduced weight. Other advantages include improved reliability with potentially reduced maintenance and better riding quality.
A numerical scheme is presented for the computation of transonic aerodynamic loads on flexible wings. The method consists of iteratively applying the loads computed by a 3D transonic aerodynamics code to a structural model to obtain elastic twist, and then recomputing the loads. Because this iteration is performed concurrently with the iterations performed in computing the aerodynamics, flexible loads are obtained in roughly the same amount of computing time as required to obtain rigid loads. Applications of this method to a flexible supercritical transonic transport wing are presented and compared with model test data.
Time-history data of airspeed, altitude, and acceleration obtained with the NACA VGH recorder from a twin-engine airplane operated by a regional feeder airline in the Rocky Mountains are evaluated to determine the magnitude and frequency of occurrence of gusts and gust accelerations and the operating airspeeds and altitudes. The results obtained are compared with the results previously obtained from a representative short-haul and long-haul operation.
This report deals with the analysis of 2-spar cantilever wings in torsion, taking cognizance of the fact that the spars are not independent, but are interconnected by ribs and other structural members. The principles of interaction are briefly explained, showing that the mutual relief action occurring depends on the "pure torsional stiffness" of the wing cross section. Various practical methods of analysis are outlined. The "Friedrichs-Von Karman equations" are shown to require the least amount of labor. Numerical examples by the several methods of analysis are given and the agreement between the calculation and experiment is shown.
This paper reports on a wind-tunnel test where load distributions were obtained at transonic speeds on both the canard and wing surfaces of a closely-coupled wing-canard configuration. The investigation included detailed component and configuration arrangement studies to provide insight into the various aerodynamic interference effects for the leading-edge vortex flow conditions encountered. Data indicate that increasing the Mach number from 0.70 to 0.95 caused the wing leading-edge vortex to burst over the wing when the wing was in the presence of the high canard. For some of the outboard span locations, the leading-edge vortex reattachment streamline intersects the wing trailing edge inboard of these span locations, thus, the Kutta condition was not satisfied. In general, the effect of adding a canard was to reduce the lift inboard and somewhat increase the lift outboard similar to the trends that would have been expected had the flow been attached.
A composite sandwich single bay wing box test article was developed by Northrop Grumman and tested recently at NASA Langley Research Center. The objectives for the wing box development effort were to provide a demonstration article for manufacturing scale up of structural concepts related to a high speed transport wing, and to validate the structural performance of the design. The box concept consisted of highly loaded composite sandwich wing skins, with moderately loaded composite sandwich spars. The dimensions of the box were chosen to represent a single bay of the main wing box, with a spar spacing of 30 inches, height of 20 inches constant depth, and length of 64 inches. The bismaleimide facesheet laminates and titanium honeycomb core chosen for this task are high temperature materials able to sustain a 300F service temperature. The completed test article is shown in Figure 1. The tests at NASA Langley demonstrated the structures ability to sustain axial tension and compression loads in excess of 20,000 lb/in, and to maintain integrity in the thermal environment. Test procedures, analysis failure predictions, and test results are presented.
The results of take-off calculations are given for an application of simple trailing-edge flaps to two hypothetical flying boats, one having medium wing and power loading and consequently considerable excess of thrust over total resistance during the take-off run, the other having high wing and power loading and a very low excess thrust. For these seaplanes the effect of downward flap settings was: (1) to increase the total resistance below the stalling speed, (2) to decrease the get-away speed, (3) to improve the take-off performance of the seaplane having considerable excess thrust, and (4) to hinder the take-off of the seaplane having low excess thrust. It is indicated that flaps would allow a decrease in the high angles of wing setting necessary with most seaplanes, provided that the excess thrust is not too low.
A new airfoil, the NLF(1)-0115, has been recently designed at the NASA Langley Research Center for use in general-aviation applications. During the development of this airfoil, special emphasis was placed on experiences and observations gleaned from other successful general-aviation airfoils. For example, the flight lift-coefficient range is the same as that of the turbulent-flow NACA 23015 airfoil. Also, although beneficial for reducing drag and having large amounts of lift, the NLF(1)-0115 avoids the use of aft loading which can lead to large stick forces if utilized on portions of the wing having ailerons. Furthermore, not using aft loading eliminates the concern that the high pitching-moment coefficient generated by such airfoils can result in large trim drags if cruise flaps are not employed. The NASA NLF(1)-0115 has a thickness of 15 percent. It is designed primarily for general-aviation aircraft with wing loadings of 718 to 958 N/sq m (15 to 20 lb/sq ft). Low profile drag as a result of laminar flow is obtained over the range from c sub l = 0.1 and R = 9x10(exp 6) (the cruise condition) to c sub l = 0.6 and R = 4 x 10(exp 6) (the climb condition). While this airfoil can be used with flaps, it is designed to achieve c(sub l, max) = 1.5 at R = 2.6 x 10(exp 6) without flaps. The zero-lift pitching moment is held at c sub m sub o = 0.055. The hinge moment for a .20c aileron is fixed at a value equal to that of the NACA 63 sub 2-215 airfoil, c sub h = 0.00216. The loss in c (sub l, max) due to leading edge roughness, rain, or insects at R = 2.6 x 10 (exp 6) is 11 percent as compared with 14 percent for the NACA 23015.
Available information on the effects of wing-fuselage-tail and wing-nacelle interference on the distribution of the air load among components of airplanes is analyzed. The effects of wing and nacelle incidence, horizontal andvertical position of wing and nacelle, fuselage shape, wing section and filleting are considered. Where sufficient data were unavailable to determine the distribution of the air load, the change in lift caused by interference between wing and fuselage was found. This increment is affected to the greatest extent by vertical wing position.
Explore the source record for details and available documents.
A hover test of a 0.658-scale model of a V-22 rotor and wing was conducted at the Outdoor Aerodynamic Research Facility at Ames Research Center. The primary objectives of the test were to obtain accurate measurements of the hover performance of the rotor system, and to measure the aerodynamic interactions between the rotor and wing. Data were acquired for rotor tip Mach numbers ranging from 0.1 to 0.73. This report presents data on rotor performance, rotor-wake downwash velocities, rotor system loads, wing forces and moments, and wing surface pressures.
An iteration method is presented by which the detailed aerodynamic loading and twist characteristics of a flexible wing with known elastic properties may be calculated. The method is applicable at Mach numbers approaching 1.0 as well as at subsonic Mach numbers. Calculations were made for a wing-body combination; the wing was swept back 45 deg and had an aspect ratio of 4. Comparisons were made with experimental results at Mach numbers from.0.80 to 0.98.
An investigation has been conducted in the Langley high- speed 7- by 10-foot tunnel to determine the effect of steady rolling on the aerodynamic loading characteristics of a 45° sweptback wing of aspect ratio 4 in combination with a fuselage. The investigation covered Mach numbers of 0.70, 0.85, and 0.91 at angles of attack up to 13°. The r esults indicate that the loss in damping in roll previously noted for this wing is due to stalling of the tip sections. The effects of rolling velocity on the span load distrib~tion can be satisfactorily estimated if measured pressure-distribution data in pitch are available.
A static aeroelastic analysis capability that calculates flexible air loads for generic configuration wings was developed. It was made possible by integrating a finite element structural analysis code (MSC/NASTRAN) and a panel code of aerodynamic analysis based on linear potential flow theory. The framework already built in MSC/NASTRAN was used, and the aerodynamic influence coefficient matrix was computed externally and inserted in the NASTRAN by means of a DMAP program. It was shown that deformation and flexible air loads of an oblique wing configuration including asymmetric wings can be calculated reliably by this code both in subsonic and supersonic speeds.