Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Warp”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Investigation at Mach Numbers of 0.60 to 3.50 of Blended Wing-Body Combinations with Cambered and Twisted Wings with Diamond, Delta and Arrow Plan Forms

This investigation is a continuation of the experimental and theoretical evaluation of blended wing-body combinations. The basic diamond, delta, and arrow plan forms which had an aspect ratio of 2 with leading-edge sweeps of 45.00 deg., 59.04 deg., and 70.82 deg. and trailing edge of -45.00 deg., -18.43 deg., and 41.19 deg., respectively, are used herein as standards for evaluating the effects of camber and warp. The wing thickness distributions were computed by varying the section shape along with the body radii (blending process) to match the prescribed area distribution and wing plan form. The wing camber and warp were computed to try to obtain nearly elliptical spanwise and chordwise load distributions for each plan form and thus to obtain low drag due to lift for a range of Mach numbers for which the velocities normal to the wing leading edge are subsonic. Elliptical chordwise load distributions were not possible for the plan forms and design conditions selected, so these distributions were somewhat different for each plan form. The models were tested with transition fixed at Mach numbers from 0.60 to 3.50 and at Reynolds numbers, based on the mean aerodynamic chord of the wing, of roughly 4,000,000 to 9,000,000. At speeds where the velocities normal to the wing leading edges were supersonic, an increase in the experimental wave-drag coefficients due to camber and twist was evident, but this penalty decreased with increased sweep. Thus the minimum wave-drag coefficients for the cambered arrow model were almost identical with the zero-lift wave- drag coefficients for the uncambered arrow model at all test Mach numbers.

Holdaway, George H.↗

Interior Noise Reduction by Adaptive Feedback Vibration Control

The objective of this project is to investigate the possible use of adaptive digital filtering techniques in simultaneous, multiple-mode identification of the modal parameters of a vibrating structure in real-time. It is intended that the results obtained from this project will be used for state estimation needed in adaptive structural acoustics control. The work done in this project is basically an extension of the work on real-time single mode identification, which was performed successfully using a digital signal processor (DSP) at NASA, Langley. Initially, in this investigation the single mode identification work was duplicated on a different processor, namely the Texas Instruments TMS32OC40 DSP. The system identification results for the single mode case were very good. Then an algorithm for simultaneous two mode identification was developed and tested using analytical simulation. When it successfully performed the expected tasks, it was implemented in real-time on the DSP system to identify the first two modes of vibration of a cantilever aluminum beam. The results of the simultaneous two mode case were good but some problems were identified related to frequency warping and spurious mode identification. The frequency warping problem was found to be due to the bilinear transformation used in the algorithm to convert the system transfer function from the continuous-time domain to the discrete-time domain. An alternative approach was developed to rectify the problem. The spurious mode identification problem was found to be associated with high sampling rates. Noise in the signal is suspected to be the cause of this problem but further investigation will be needed to clarify the cause. For simultaneous identification of more than two modes, it was found that theoretically an adaptive digital filter can be designed to identify the required number of modes, but the algebra became very complex which made it impossible to implement in the DSP system used in this study. The on-line identification algorithm developed in this research will be useful in constructing a state estimator for feedback vibration control.

Lim, Tae W.↗

Development of Textile Reinforced Composites for Aircraft Structures

NASA has been a leader in development of composite materials for aircraft applications during the past 25 years. In the early 1980's NASA and others conducted research to improve damage tolerance of composite structures through the use of toughened resins but these resins were not cost-effective. The aircraft industry wanted affordable, robust structures that could withstand the rigors of flight service with minimal damage. The cost and damage tolerance barriers of conventional laminated composites led NASA to focus on new concepts in composites which would incorporate the automated manufacturing methods of the textiles industry and which would incorporate through-the-thickness reinforcements. The NASA Advanced Composites Technology (ACT) Program provided the resources to extensively investigate the application of textile processes to next generation aircraft wing and fuselage structures. This paper discusses advanced textile material forms that have been developed, innovative machine concepts and key technology advancements required for future application of textile reinforced composites in commercial transport aircraft. Multiaxial warp knitting, triaxial braiding and through-the-thickness stitching are the three textile processes that have surfaced as the most promising for further development. Textile reinforced composite structural elements that have been developed in the NASA ACT Program are discussed. Included are braided fuselage frames and window-belt reinforcements, woven/stitched lower fuselage side panels, stitched multiaxial warp knit wing skins, and braided wing stiffeners. In addition, low-cost processing concepts such as resin transfer molding (RTM), resin film infusion (RFI), and vacuum-assisted resin transfer molding (VARTM) are discussed. Process modeling concepts to predict resin flow and cure in textile preforms are also discussed.

Dexter, H. Benson↗

Multi-Epoch XMM Observations of NGC4258

The goal of this project is to better understand whether the well known, warped accretion disk around the supermassive black hole in NGC4258 is responsible for the observed X-ray absorbing column of gas. The active galactic nuclei (AGN) paradigm suggests that doughnut-like tori obscure black holes, not warped disks. Using radio interferometry, we have mapped the disk and its orientation. Through time monitoring radio observations we are following the rotation and variability in the disk structure. The disk crosses the line of sight to the black hole, if it is clumpy, then we will observe variations in the X-ray spectrum of NGC4258 on month to year time scales. We have reduced 14 epochs of very long base interferometry (VLBI) observations that we use to characterize the structure of the maser-laden accretion disk and its evolution. Five epochs of data remain to be reduced in the next year. We have received distributions of data for two of our four intended epochs of X-ray Multimirror Mission (XMM) observation. Because the first two epochs are relatively close in time, and because community understanding of how to calibrate XMM data has until recently been relatively immature, we are waiting until we receive the third epoch of data before we reduce the several datasets. Delivery of the third epoch should take place late this year. The last epoch of XMM observation will take place in mid-2002. In the next year, we will begin to combine constraints on disk clumpiness with estimates of X-ray variability observed by XMM.

Greenhill, Lincoln J.↗

Long-Term Properties of Accretion Discs in X-ray Binaries: The Variable Third Period in SMC X-1 - 1

Long term X-ray monitoring data from the RXTE All Sky Monitor (ASM) reveal that the third (superorbital) period in SMC X-1 is not constant but varies between 40-60 days. A dynamic power spectrum analysis indicates that the third period has been present continuously throughout the five years of ASM observations. This period changed smoothly from 60 days to 45 days and then returned to its former value, on a timescale of approximately 1600 days. During the nearly 4 years of overlap between the CGRO & RXTE missions, the simultaneous BATSE hard X-ray data confirm this variation in SMC X-1. Sources of systematic error and possible artefacts are investigated and found to be incapable of reproducing the results reported here. Our disco cry of such an instability in the superorbital period of SMC X-1 is interpreted in the context of recent theoretical studies of warped, precessing accretion discs. We find that the behaviour of SMC X-1 is consistent with a radiation - driven warping model.

Charles, P. A.↗

Multi-Epoch XMM Observations of NGC4258

The goal of this project was detection of variability in the X-ray absorption column of the AGN in NGC4258 through monitoring with the XMM satellite. We have accomplished this goal and submitted the results to ApJ for publication in a paper entitled, "X-ray Luminosity and Absorption Column Fluctuations in the H2O Maser Galaxy NGC4258 from Weeks to Years," by Fruscione, A., Greenhill, L.J., Filippedco, A.V., Moran, J.M., Hermstein, J.R., and Galle, E. We have received a favorable referee report and expect the article will appear in 2005. To complete the project, we reduced our four epochs of XMM data for NGC4258, one archival XMM observation, and all existing Chandra datasets for NGC4258 (with the latest calibration tables and a grid of corrections for pileup). Self-consistent reduction of all these data permitted detailed comparison that could not have been accomplished simply by taking published model fits that appear in the literature. To accumulate a broader monitoring record, we combined the Chandra and XMM results with those published for SAX and ASCA. We modeled the Chandra and XMM data self-consistently with partially absorbed, hard power-law, soft thermal plasmas, and soft power-law components. Over nine years, the photo-electric absorbing column exhibited a 40% drop between two ASCA epochs separated by 3 years and a 60% rise between two XMM epochs separated by just 5 months. In contract, uncorrelated factor of of 2-3 changes were seen in absorbed flux on te timescale of years, which suggests intrinsic variability of the central engine. The warped disk that is a known source of H2O maser emission in 4258 is believed to cross the line of sight to the central engine. We have proposed that the variations in absorbing column arise from inhomogeneities in the rotating disk, as they sweep across the line of sight. We estimate from the XMM data that the inhomogeneities are about 1E+15 cm in size at radii greater than 0.27 pc. This is consistent with the estimated radius of the disk crossing estimated entirely independently, and it solidifies evidence that the warped accretion disk is the absorber in this (and possible other) AGN.

Greenhill, Lincoln J.↗

Design and Experimental Verification of Deployable/Inflatable Ultra-Lightweight Structures

Because launch cost of a space structural system is often proportional to the launch volume and mass and there is no significant gravity in space, NASA's space exploration programs and various science missions have stimulated extensive use of ultra-lightweight deployable/inflatable structures. These structures are named here as Highly Flexible Structures (HFSs) because they are designed to undergo large displacements, rotations, and/or buckling without plastic deformation under normal operation conditions. Except recent applications to space structural systems, HFSs have been used in many mechanical systems, civil structures, aerospace vehicles, home appliances, and medical devices to satisfy space limitations, provide special mechanisms, and/or reduce structural weight. The extensive use of HFSs in today's structural engineering reveals the need of a design and analysis software and a database system with design guidelines for practicing engineers to perform computer-aided design and rapid prototyping of HFSs. Also to prepare engineering students for future structural engineering requires a new and easy-to- understand method of presenting the complex mathematics of the modeling and analysis of HFSs. However, because of the high flexibility of HFSs, many unique challenging problems in the modeling, design and analysis of HFSs need to be studied. The current state of research on HFSs needs advances in the following areas: (1) modeling of large rotations using appropriate strain measures, (2) modeling of cross-section warpings of structures, (3) how to account for both large rotations and cross- section warpings in 2D (two-dimensional) and 1D structural theories, (4) modeling of thickness thinning of membranes due to inflation pressure, pretension, and temperature change, (5) prediction of inflated shapes and wrinkles of inflatable structures, (6) development of efficient numerical methods for nonlinear static and dynamic analyses, and (7) filling the gap between geometrically exact elastic analysis and elastoplastic analysis. The objectives of this research project were: (1) to study the modeling, design, and analysis of deployable/inflatable ultra-lightweight structures, (2) to perform numerical and experimental studies on the static and dynamic characteristics and deployability of HFSs, (3) to derive guidelines for designing HFSs, (4) to develop a MATLAB toolbox for the design, analysis, and dynamic animation of HFSs, and (5) to perform experiments and establish an adequate database of post-buckling characteristics of HFSs.

Pai, P. Frank↗

The Interstellar Conspiracy

If we were designing a human-carrying starship that could be launched in the not-too-distant future, it would almost certainly not use a warp drive to instantaneously bounce around the universe, as is done in Isaac Asimov's classic Foundation series or in episodes of Star Trek or Star Wars. Sadly, those starships that seem to be within technological reach could not even travel at high relativistic speeds, as does the interstellar ramjet in Poul Anderson's Tau Zero. Warp-speeds seem to be well outside the realm of currently understood physical law; proton-fusing ramjets may never be technologically feasible. Perhaps fortunately in our terrorist-plagued world, the economics of antimatter may never be attractive for large-scale starship propulsion. But interstellar travel will be possible within a few centuries, although it will certainly not be as fast as we might prefer. If humans learn how to hibernate, perhaps we will sleep our way to the stars, as do the crew in A. E. van Vogt's Far Centaurus. However, as discussed in a landmark paper in The Journal of the British Interplanetary Society, the most feasible approach to transporting a small human population to the planets (if any) of Alpha Centauri is the worldship. Such craft have often been featured in science fiction. See for example Arthur C. Clarke's Rendezvous with Rama, and Robert A. Heinlein's Orphans of the Sky. Worldships are essentially mobile versions of the O Neill free-space habitats. Constructed mostly from lunar and/or asteroidal materials, these solar-powered, multi-kilometer-dimension structures could house 10,000 to 100,000 humans in Earth-approximating environments. Artificial gravity would be provided by habitat rotation, and cosmic ray shielding would be provided by passive methods, such as habitat atmosphere and mass shielding, or magnetic fields. A late 21st century space-habitat venture might support itself economically by constructing large solar-powered satellites to beam energy back to Earth.

Johnson, Les↗

Adjustable reed for weaving net-shaped tailored fabrics

An apparatus and method for forming woven fabrics through the use of an adjustable reed. The adjustable reed has multiple groups of reed wires that guide the warp yarns. The groups of reed wires move on reed rails parallel to the warp direction. In addition, rail expanders permit the space between the reed wires to be modified and telescoping rods attached to the rail sliders can be turned to permit the reed wires to be skewed to alter the fill yarn angle. These adjustments to the reed permit simultaneous variation of fill yarn angles and fabric widths and allow these variations to be made during fabrication, without the need to halt production.

Farley, Gary L.↗

Laboratory-Based Bidirectional Reflectance Distribution Functions of Radiometric Tarps

Laboratory-based bidirectional reflectance distribution functions of radiometric tarp samples used in the vicarious calibration of Earth remote sensing satellite instruments are presented in this paper. The results illustrate the BRDF dependence on the orientation of the tarps weft and warp threads. The study was performed using the GSFC scatterometer at incident zenith angles of 0 deg, 10 deg, and 30 deg; scatter zenith angles from 0 deg. to 60 deg.; and scatter azimuth angles of 0 deg., 45 deg., 90 deg., 135 deg. and 180 deg. The wavelengths were 485nm, 550nm, 633nm and 800nm. The tarp's weft and warp dependence on BRDF is well defined at all measurement geometries and wavelengths. The BRDF difference can be as high as 8% at 0o incident angle and 12% at 30 deg. incident angle. The fitted BRDF data shows a very small discrepancy from the measured ones. New data on the forward and backscatter properties of radiometric tarps are reported. The backward scatter is well pronounced for the white samples. The black sample has well pronounced forward scatter. The provided BRDF characterization of radiometric tarps is an excellent reference for anyone interested in using tarps for radiometric calibrations. The results are NIST traceable.

Georgiev, Georgi T.↗

Parallel-Processing Software for Creating Mosaic Images

A computer program implements parallel processing for nearly real-time creation of panoramic mosaics of images of terrain acquired by video cameras on an exploratory robotic vehicle (e.g., a Mars rover). Because the original images are typically acquired at various camera positions and orientations, it is necessary to warp the images into the reference frame of the mosaic before stitching them together to create the mosaic. [Also see "Parallel-Processing Software for Correlating Stereo Images," Software Supplement to NASA Tech Briefs, Vol. 31, No. 9 (September 2007) page 26.] The warping algorithm in this computer program reflects the considerations that (1) for every pixel in the desired final mosaic, a good corresponding point must be found in one or more of the original images and (2) for this purpose, one needs a good mathematical model of the cameras and a good correlation of individual pixels with respect to their positions in three dimensions. The desired mosaic is divided into slices, each of which is assigned to one of a number of central processing units (CPUs) operating simultaneously. The results from the CPUs are gathered and placed into the final mosaic. The time taken to create the mosaic depends upon the number of CPUs, the speed of each CPU, and whether a local or a remote data-staging mechanism is used.

Klimeck, Gerhard↗

Probing the Accretion Disk and Central Engine Structure of the NGC 4258 with Suzaku and XMM-Newton Observations

We present an X-ray study of the low-luminosity active galactic nucleus (AGN) in NGC 4258 using data from Suzaku, XMM-Newton, and the Swift/Burst Alert Telescope survey. We find that signatures of X-ray reprocessing by cold gas are very weak in the spectrum of this Seyfert-2 galaxy; a weak, narrow fluorescent K(alpha) emission line of cod iron is robustly detected in both the Suzaku and XMM-Newton spectra but at a level much below that of most other Seyfert-2 galaxies. We conclude that the circumnuclear environment of this AGN is very "clean" and lacks the Compton-thick obscuring torus of unified Seyfert schemes. From the narrowness of the iron line, together with evidence of line flux variability between the Suzaku and XMM-Newton observations, we constrain the line emitting region to be between 3 x 10(exp 3)r(sub g) and 4 x 10(exp 4)r(sub g), from the black hole. We show that the observed properties of the iron line can be explained if the line originates from the surface layers of a warped accretion disk. In particular, we present explicit calculations of the expected iron line from a disk warped by Lens-Thirring precession from a misaligned central black hole. Finally, the Suzaku data reveal clear evidence of large amplitude 2-10 keV variability on timescales of 50 ksec and smaller amplitude flares on timescales as short as 5-10 ksec. If associated with accretion disk processes, such rapid variability requires an origin in the innermost regions of the disk (r approx. equals 10(r(sub g) or less). Analysis of the difference spectrum between a high- and low-flux states suggests that the variable component of the X-ray emission is steeper and more absorbed than the average AGN emission, suggesting that the primary X-ray source and absorbing screen have a spatial structure on comparable scales. We note the remarkable similarity between the circumnuclear environment of NGC 4258 and another well studied low-luminosity AGN, M81*.

Reynolds, Christopher S.↗

Holodeck: Telepresence Dome Visualization System Simulations

This paper explores the simulation and consideration of different image-projection strategies for the Holodeck, a dome that will be used for highly immersive telepresence operations in future endeavors of the National Aeronautics and Space Administration (NASA). Its visualization system will include a full 360 degree projection onto the dome's interior walls in order to display video streams from both simulations and recorded video. Because humans innately trust their vision to precisely report their surroundings, the Holodeck's visualization system is crucial to its realism. This system will be rigged with an integrated hardware and software infrastructure-namely, a system of projectors that will relay with a Graphics Processing Unit (GPU) and computer to both project images onto the dome and correct warping in those projections in real-time. Using both Computer-Aided Design (CAD) and ray-tracing software, virtual models of various dome/projector geometries were created and simulated via tracking and analysis of virtual light sources, leading to the selection of two possible configurations for installation. Research into image warping and the generation of dome-ready video content was also conducted, including generation of fisheye images, distortion correction, and the generation of a reliable content-generation pipeline.

Hite, Nicolas↗

Advanced Propulsion Physics Lab: Eagleworks Investigations

Eagleworks Laboratory is an advanced propulsions physics laboratory with two primary investigations currently underway. The first is a Quantum Vacuum Plasma Thruster (QVPT or Q-thrusters), an advanced electric propulsion technology in the development and demonstration phase. The second investigation is in Warp Field Interferometry (WFI). This is an investigation of Dr. Harold "Sonny" White's theoretical physics models for warp field equations using optical experiments in the Electro Optical laboratory (EOL) at Johnson Space Center. These investigations are pursuing technology necessary to enable human exploration of the solar system and beyond.

Scogin, Tyler↗

The Effect of Laser Scan Strategy on Distortion and Residual Stresses of Arches Made With Selective Laser Melting

The NASA Marshall Space Flight Center (MSFC) is developing Additive Manufacturing (AM) - both in-space AM for on-demand parts, tools, or structures, and on-earth AM for rapid, reduced-cost, small volume production of complex space-flight hardware. Selective Laser Melting (SLM) is an on-earth AM technology that MSFC is using to build Alloy 718 rocket engine components. An understanding of the SLM-718 material properties is required to design, build, and qualify these components for space flight. Residual stresses and are of particular interest for this AM process, since SLM is a series of approximately 100 micron-wide welds, where highly non-linear heating and cooling, severe thermal gradients and repeated thermal cycling can result in high residual stresses within the component. These stresses may cause degraded material properties, and warp or distort the geometry of the SLM component. The distortions can render the component out-of-tolerance when inspected, and even interrupt or halt the build process if the warped material prevents the SLM machine from operating properly. The component must be scrapped and re-designed, which is time consuming and costly. If residual stresses are better understood, and can be predicted, these effects can be mitigated early in the component's design. the compressive residual stresses in the z-direction were highest in the chess sample, followed by island then continuous. This may be due to the binding nature of the segments

Bagg, Stacey D.↗

Integral Textile Structure for 3-D CMC Turbine Airfoils

An integral textile structure for 3-D CMC turbine airfoils includes top and bottom walls made from an angle-interlock weave, each of the walls comprising warp and weft fiber tows. The top and bottom walls are merged on a first side parallel to the warp fiber tows into a single wall along a portion of their widths, with the weft fiber tows making up the single wall interlocked through the wall's thickness such that delamination of the wall is inhibited. The single wall suitably forms the trailing edge of an airfoil; the top and bottom walls are preferably joined along a second side opposite the first side and parallel to the radial fiber tows by a continuously curved section in which the weave structure remains continuous with the weave structure in the top and bottom walls, the continuously curved section being the leading edge of the airfoil.

Marshall, David B.↗

Open Source Mission Control for Chrome

New technology presents the possibility to evolve mission control. WARP (Web Applications for Resource Prospector) a new open source toolset for mission visualization, brings mission control to the Chrome Web Browser. WARP integrates multiple data sources into a coherent visualization toolset from which users may assemble their own software, thus giving mission controllers more flexibility. This frees us to operate based on mission needs, rather than constraints enforced by software application boundaries.

software engineering↗

Memory Optimizations for Sparse Linear Algebra on GPU Hardware

An effort to maximize memory bandwidth utilization for a sparse linear algebra kernel executing on NVIDIA® Tesla V100 and A100 Graphics Processing Units (GPUs) is described. The kernel consists of a block-sparse matrix-vector product and a series of forward/backward triangular solves. The computation is memory-bound and exhibits low arithmetic intensity. Along with a relatively small block size, the data layout poses a challenge to effectively utilize the available memory bandwidth on common GPU architectures. An earlier implementation using a warp to process a single row of the matrix was found to yield good memory performance on the V100 architecture. However, anew approach, which assigns a warp to six rows of the matrix, is proposed for the A100. In addition, two new features offered by the A100 architecture are explored.L2residency control enables a portion of theL2cache to be used for persistent data access, and the asynchronous copy instruction allows data to be loaded directly from main memory into shared memory. Demonstrations show that the new implementation improves memory bandwidth utilization from 71.5% to 81.2% of the peak available on theA100 architecture.

GPU↗