Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VORTEX”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Vortex generator installation studies on steady state and dynamic inlet distortion

The theoretical and experimental work carried out under the NASA/MOD Joint Aeronautical Program has shown that CFD vortex generator installations designs successfully managed inlet duct flow distortion and that significant benefits in flow unsteadiness at the engine face were also present. The main conclusions to date from the collaborative effort between NASA/Lewis and DRA/Bedford are as follows: (1) vortex generator installations can be designed to be effective over a wide range of inlet operating conditions using Computational Fluid Dynamics and formal optimization procedures, (2) reductions in steady state engine face distortion of up to 80% have been measured in the M2129 inlet S-duct using CFD designed vortex generator installations, (3) reductions in flow unsteadiness of up to 80% have been measured in the W129 inlet S-duct using CFD designed vortex generator installations, and (4) the Reduced Navier-Stokes code RNS3D is a useful tool to design vortex generator installations to manage engine face distortions over a wide range of inlet operating conditions.

Anderson, Bernhard H.↗

Analog Processing Assembly for the Wake Vortex Lidar Experiment

The Federal Aviation Administration (FAA) and NASA have initiated a joint study in the development of reliable means of tracking, detecting, measuring, and predicting trailing wake-vortices of commercial aircraft. Being sought is an accurate model of the wake-vortex hazard, sufficient to increase airport capacity by reducing minimum safe spacings between planes. Several means of measurement are being evaluated for application to wake-vortex detection and tracking, including Doppler RADAR (Radio Detection and Ranging) systems, 2-micron Doppler LIDAR (Light Detection And Ranging) systems, and SODAR (Sound Detection And Ranging) systems. Of specific interest there is the lidar system, which has demonstrated numerous valuable capabilities as a vortex sensor Aerosols entrained in the vortex flow make the wake velocity signature visible to the lidar, (the observable lidar signal is essentially a measurement of the line-of-sight velocity of the aerosols). Measurement of the occurrence of a wake vortex requires effective reception and monitoring of the beat signal which results from the frequency-offset between the transmitted pulse and the backscattered radiation. This paper discusses the mounting, analysis, troubleshooting, and possible use of an analog processing assembly designed for such an application.

Stowe, Edwood G.↗

Wake Vortex Encounter Research

The National Aeronautics and Space Administration (NASA) is conducting research to improve airport capacity by reducing the separation distance between aircraft. The limiting factor in reducing separation distances and improving airport capacity is the wake vortex hazard. The ability to accurately model wake vortices and predict the outcome of a vortex encounter is critical in developing a system to safely improve airport capacity. This is the focus of the wake vortex research being done at NASA Langley Research Center (LaRC). This paper will concentrate on two topics. The first topic is the control system developed for the Boeing 737 freeflight model in support of vortex encounter tests to be conducted in the 30- by 60- foot tunnel at NASA Langley Research Center later this year. The second topic discussed is the limited degree of freedom (DOF) trajectory generation study that is being conducted to determine the relative severity of a multitude of paths through a wake vortex.

Wilson, Jeffrey M.↗

A Computational-Experimental Development of Vortex Generator Use for a Transitioning S-Diffuser

The development of an effective design strategy for surface-mounted vortex generator arrays in a subsonic diffuser is described in this report. This strategy uses the strengths of both computational and experimental analyses to determine beneficial vortex generator locations and sizes. A parabolized Navier-Stokes solver, RNS3D, was used to establish proper placement of the vortex generators for reduction in circumferential total pressure distortion. Experimental measurements were used to determine proper vortex generator sizing to minimize total pressure recovery losses associated with vortex generator device drag. The best result achieved a 59% reduction in the distortion index DC60, with a 0.3% reduction in total pressure recovery.

Wendt, Bruce J.↗

Rotor Vortex Filaments: Living on the Slipstream's Edge

The purpose of this paper is to gain a better understanding of rotor wake evolution in hover and axial flow by deriving an analytical solution for the time dependent behavior of vortex filament circulation and core size. This solution is applicable only for vortex filaments in the rotor far-wake. A primarily inviscid vortex/shear layer interaction (where the slipstream boundary is modeled as a shear layer) has been identified in this analytical treatment. This vortex/shear layer interaction results in decreasing, vortex filament circulation and core size with time. The inviscid vortex/shear layer interaction is shown, in a first-order treatment, to be of greater magnitude than viscous diffusion effects. The rate of contraction, and ultimate collapse, of the vortex filament core is found to be directly proportional to the rotor inflow velocity. This new insight into vortex filament decay promises to help reconcile several disparate observations made in the literature and will, hopefully, promote new advances in theoretical modeling of rotor wakes.

Young, Larry A.↗

ATMOS/ATLAS-3 Observations of Long-Lived Tracers and Descent in the Antarctic Vortex in November 1994

Observations of the long-lived tracers N2O, CH4 and HF obtained by the Atmospheric Trace Molecule Spectroscopy (ATMOS) instrument in early November 1994 are used to estimate average descent rates during winter in the Antarctic polar vortex of 0.5 to 1.5 km/month in the lower stratosphere, and 2.5 to 3.5 km/month in the middle and upper stratosphere. Descent rates inferred from ATMOS tracer observations agree well with theoretical estimates obtained using radiative heating calculations. Air of mesospheric origin (N2O less than 5 ppbV) was observed at altitudes above about 25 km within the vortex. Strong horizontal gradients of tracer mixing ratios, the presence of mesospheric air in the vortex in early spring, and the variation with altitude of inferred descent rates indicate that the Antarctic vortex is highly isolated from midlatitudes throughout the winter from approximately 20 km to the stratopause. The 1994 Antarctic vortex remained well isolated between 20 and 30 km through at least mid-November.

Abrams, M. C.↗

ATMOS Measurements of H2O + 2CH4 and Total Reactive Nitrogen in the November 1994 Antarctic Stratosphere: Dehydration and Denitrification in the Vortex

Simultaneous stratospheric volume mixing ratios (VMR's) measured inside and outside the Antarctic vortex by the Atmospheric Trace Molecule Spectroscopy (ATMOS) instrument in November 1994 reveal previously unobserved features in the distributions of total reactive nitrogen (NO(y)) and total hydrogen (H2O + 2CH4). Maximum removal of NO(y) due to sedimentation of polar stratospheric clouds (PSC's) inside the vortex occurred at a potential temperature (Theta) of 500-525 K (approximately 20 km), where values were 5 times smaller than measurements outside. Maximum loss of H2O + 2CH4 due to PSC's occurred in the vortex at 425-450 K, approximately 3 km lower than the peak NO(y) loss. At that level, H2O + 2CH4 VMR's inside the vortex were approximately 70% of corresponding values outside. The Antarctic and April 1993 Arctic measurements by ATMOS show no significant differences in H2O + 2CH4 VMR's outside the vortices in the two hemispheres. Elevated NO(y) VMRs were measured inside the vortex near 700 K. Recent model calculations indicate that this feature results from downward transport of elevated NO(y) produced in the thermosphere and mesosphere.

Rinsland, C. P.↗

Proceedings of the NASA First Wake Vortex Dynamic Spacing Workshop

A Government and Industry workshop on wake vortex dynamic spacing systems was conducted on May 13-15, 1997, at the NASA Langley Research Center. The purpose of the workshop was to disclose the status of ongoing NASA wake vortex R&D to the international community and to seek feedback on the direction of future work to assure an optimized research approach. Workshop sessions examined wake vortex characterization and physics, wake sensor technologies, aircraft/wake encounters, terminal area weather characterization and prediction, and wake vortex systems integration and implementation. A final workshop session surveyed the Government and Industry perspectives on the NASA research underway and related international wake vortex activities. This document contains the proceedings of the workshop including the presenters' slides, the discussion following each presentation, the wrap-up panel discussion, and the attendees' evaluation feedback.

Creduer, Leonard↗

NASA Research on the Hydrodynamics of the Gaseous Vortex Reactor

The experimental and analytical results to date of a study of a two-component gaseous vortex system are presented in this paper. Analytical expressions for tangential velocity and static-pressure profiles in a turbulent vortex show good agreement with experimental data. Airflow rates from 0.075 to 0.14 pound per second and corresponding tangential velocities from 160 to 440 feet per second are correlated by turbulent Reynolds numbers from 1.95 to 2.4. An analysis of an air-bromine gas mixture in a turbulent vortex indicates that a boundary value of bromine-to-air radial velocity ratio (u(2)/u(1)) of 0.999 gives essentially no bromine buildup, while a value of 0.833 results in considerable separation. For a constant value of (u(2)/u(1))(0) the bromine buildup increases as (1) the tangential velocity increases, (2) the air-to-bromine weight-flow ratio decreases, (3) the airflow rate decreases, (4) the temperature decreases, and (5) the turbulence decreases. Analytical temperature, pressure, and tangential-velocity profiles are also presented. Preliminary experimental results indicate that the flow of an air-bromine mixture through a vortex field results in a bromine density increase to a maximum value; followed by a decrease; the air density exhibits a uniform decrease from the outer vortex radius to the exhaust-nozzle radius.

Ragsdale, Robert G.↗

Experiments on Diffusion Flame Structure of a Laminar Vortex Ring

The study of flame-vortex interactions provides one of the means to better understand turbulent combustion, and allows for canonical configurations that contain the fundamental elements found in turbulent flames, These include concentrated vorticity, entrainment and mixing, strain and nonequilibrium phenomena, diffusion and differential diffusion, partial premixing and diluent effects, and heat release effects. In flame- vortex configurations, these fundamental elements can be studied under more controlled conditions than is possible in direct investigations of turbulent flames. Since the paper of Marble, the problem of the flame-vortex interaction has received considerable attention theoretically, numerically and experimentally. Several configurations exist for study of the premixed flame/vortex ring interaction but more limited results have been obtained to date for the diffusion flame/vortex ring case. The setup of Chen and Dahm, which is conceptually similar to that of Karagozian and Manda and Karagozian, Suganuma and Strom where the ring is composed of fuel and air and combustion begins during the ring formation process, is used in the current study. However, it is essential to conduct the experiments in microgravity to remove the asymmetries caused by buoyancy and thus obtain highly symmetric and repeatable interactions. In previous studies it was found that the flame structure of the vortex ring was similar to that obtained analytically by Karagozian and Manda. Dilution of propane with nitrogen led mainly to a reduction in flame luminosities, flame burnout times were affected by both fuel volumes and amount of dilution, and a simple model of the burnout times was developed. In this paper, a discussion on reacting ring displacement and flame burnout time will be given, and the flame structures of vortex rings containing ethane and air will be compared to those of propane reacting in air.

Chen, Shin-Juh↗

Vortex-State Complex Hall Conductivity of Superconducting YBa2Cu3O7 Epitaxial Films at Radio Frequencies

The first intermediate-frequency measurements of the vortex-state complex Hall conductivity \sigma_xy of YBa_2CU_3O_7 superconducting epitaxial films are reported. A direct transport measurement technique from dc to 7 MHz was used. The results are analyzed in terms of a phenomenological model, generalized from that for the dc Hall conductivity, with the assumptions that: 1) the sign reversal in the vortex-state Hall conductivity is associated with the different carrier densities within and far away from the vortex cores; 2) the Drude approximation Is applicable; and 3) the anomalous sign reversal occurs in the flux-flow Limit. The temperature, frequency, and magnetic field (B) dependencies of our \sigma_xy data are in good agreement with the model. The B-dependence of \sigma_xy reveals that both vortices (\sigma_xyAv \propto BA-1) and quasiparticles (sigma_xyAq \propto B) contribute to the vortex-state Hall conduction. The magnitude of the real part of \sigma_xy, \sigma_xyA\prime, is in good agreement with our model, while that of the imaginary part, \sigma_xyA\prime \prime, is significantly Luger than the theoretical prediction. This may be attributed to the unconventional electronic structures in the vortex core of cuprate superconductors with d-wave or mixed pairing symmetries.

Beam, D. A.↗

Defining the Polar Vortex Edge Using an N2O: Potential Temperature Correlation Versus the Nash Criterion: A Comparison

A prerequisite to study phenomena in the winter stratospheric polar vortex is the separation of measurements inside and outside the dynamical barrier of the vortex edge. We describe a technique to accurately determine the inner edge of the vortex boundary region from measurements of potential temperature and a trace gas, such as N2O, and apply it to in situ aircraft and balloon measurements from the SOLVE/THESE02000 Arctic campaign. The method may be used to refine the Nash algorithm, which, due to the inherently coarser resolution of potential vorticity on which it is dependent, may misidentify the inner edge by up to 466 km, and omit the identification of small, extra-vortex filaments within the vortex.

Greenblatt, Jeffery B.↗

Vortex Core Size in the Rotor Near-Wake

Using a kinetic energy conservation approach, a number of simple analytic expressions are derived for estimating core size of tip vortices in the near-wake of rotors in hover or axial-flight (climb). The influence of thrust, axial-flight advance ratio, blade count, blade aspect ratio, nonuniform disk loading, and vortex structure on rotor vortex core size is assessed. Vortex core size is found to be directly proportional to rotor thrust and inversely proportional to axial-flight advance ratio. Further, it is found that the more efficient the rotor is with respect to factors that affect induced power, the smaller the vortex core size. In particular, uniformity of the rotor disk loading clearly has the greatest influence on vortex core size of the parameters studied in this paper.

Young, Larry A.↗

Simulation of Rotary-Wing Near-Wake Vortex Structures Using Navier-Stokes CFD Methods

This paper will use high-resolution Navier-Stokes computational fluid dynamics (CFD) simulations to model the near-wake vortex roll-up behind rotor blades. The locations and strengths of the trailing vortices will be determined from newly-developed visualization and analysis software tools applied to the CFD solutions. Computational results for rotor nearwake vortices will be used to study the near-wake vortex roll up for highly-twisted tiltrotor blades. These rotor blades typically have combinations of positive and negative spanwise loading and complex vortex wake interactions. Results of the computational studies will be compared to vortex-lattice wake models that are frequently used in rotorcraft comprehensive codes. Information from these comparisons will be used to improve the rotor wake models in the Tilt-Rotor Acoustic Code (TRAC) portion of NASA's Short Haul Civil Transport program (SHCT). Accurate modeling of the rotor wake is an important part of this program and crucial to the successful design of future civil tiltrotor aircraft. The rotor wake system plays an important role in blade-vortex interaction noise, a major problem for all rotorcraft including tiltrotors.

Kenwright, David↗

Wake-Vortex Hazards During Cruise

Even though the hazard posed by lift-generated wakes of subsonic transport aircraft has been studied extensively for approach and departure at airports, only a small amount of effort has gone into the potential hazard at cruise altitude. This paper reports on a studio of the wake-vortex hazard during cruise because encounters may become more prevalent when free-flight becomes available and each aircraft, is free to choose its own route between destinations. In order to address the problem, the various fluid-dynamic stages that vortex wakes usually go through as they age will be described along with estimates of the potential hazard that each stage poses. It appears that a rolling-moment hazard can be just as severe at cruise as for approach at airports, but it only persists for several minutes. However, the hazard posed by the downwash in the wake due to the lift on the generator aircraft persists for tens of minutes in a long narrow region behind the generating aircraft. The hazard consists of severe vertical loads when an encountering aircraft crosses the wake. A technique for avoiding vortex wakes at cruise altitude will be described. To date the hazard posed by lift-generated vortex wakes and their persistence at cruise altitudes has been identified and subdivided into several tasks. Analyses of the loads to be encounter and are underway and should be completed shortly. A review of published literature on the subject has been nearly completed (see text) and photographs of vortex wakes at cruise altitudes have been taken and the various stages of decay have been identified. It remains to study and sort the photographs for those that best illustrate the various stages of decay after they are shed by subsonic transport aircraft at cruise altitudes. The present status of the analysis and the paper are described.

Rossow, Vernon J.↗

A Discrete-Vortex Method for Studying the Wing Rock of Delta Wings

A discrete-vortex method is developed to investigate the wing rock problem associated with highly swept wings. The method uses two logarithmic vortices placed above the wing to represent the vortex flow field and uses boundary conditions based on conical flow, vortex rate of change of momentum, and other considerations to position the vortices and determine their strengths. A relationship based on the time analogy and conical-flow assumptions is used to determine the hysteretic positions of the vortices during roll oscillations. Static and dynamic vortex positions and wing rock amplitudes and frequencies calculated by using the method are generally in good agreement with available experimental data. The results verify that wing rock is caused by hysteretic deflections of the vortices and indicate that the stabilizing moments that limit wing rock amplitudes are the result of the one primary vortex moving outboard of the wing where it has little influence on the wing.

Gainer, Thomas G.↗

Rotor Wake Vortex Definition: Initial Evaluation of 3-C PIV Results of the Hart-II Study

An initial evaluation is made of extensive three-component (3C) particle image velocimetry (PIV) measurements within the wake across a rotor disk plane. The model is a 40 percent scale BO-105 helicopter main rotor in forward flight simulation. This study is part of the HART II test program conducted in the German-Dutch Wind Tunnel (DNW). Included are wake vortex field measurements over the advancing and retreating sides of the rotor operating at a typical descent landing condition important for impulsive blade-vortex interaction (BVI) noise. Also included are advancing side results for rotor angle variations from climb to steep descent. Using detailed PIV vector maps of the vortex fields, methods of extracting key vortex parameters are examined and a new method was developed and evaluated. An objective processing method, involving a center-of-vorticity criterion and a vorticity 'disk' integration, was used to determine vortex core size, strength, core velocity distribution characteristics, and unsteadiness. These parameters are mapped over the rotor disk and offer unique physical insight for these parameters of importance for rotor noise and vibration prediction.

Burley, Casey L.↗

Source Term Model for an Array of Vortex Generator Vanes

A source term model was developed for numerical simulations of an array of vortex generators. The source term models the side force created by a vortex generator being modeled. The model is obtained by introducing a side force to the momentum and energy equations that can adjust its strength automatically based on a local flow. The model was tested and calibrated by comparing data from numerical simulations and experiments of a single low-profile vortex generator vane, which is only a fraction of the boundary layer thickness, over a flat plate. The source term model allowed a grid reduction of about seventy percent when compared with the numerical simulations performed on a fully gridded vortex generator without adversely affecting the development and capture of the vortex created. The source term model was able to predict the shape and size of the stream wise vorticity and velocity contours very well when compared with both numerical simulations and experimental data.

Buning, P. G.↗