Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UNLOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Acoustic emission analysis of cyclically loaded superelastic shape memory alloy fiber reinforced mortar beams

Superelastic shape memory alloys (SMAs) are metallic alloys that can recover their nonlinear deformations upon unloading. The use of SMAs in cementitious composites as fibers can enable crack recovery and re-centering capabilities. In this study, the crack recovery characteristics of SMA fiber reinforced mortar specimens subjected to flexural cyclic loading are studied through acoustic emission analysis. SMA fiber reinforced mortar specimens with fiber volume ratios of 0.3%, 0.5% and 1.0% are tested under cyclic flexural loads. Acoustic emissions (AE) signals are captured and analyzed to characterize the crack formation and crack width development at each cycle of loading. In addition, the crack width propagation of the specimens is monitored by Digital Image Correlation measurement system and is used as a basis in AE analyses. Results show that the SMA fiber reinforced mortars exhibit considerable re-centering and crack recovery characteristics at large deformation amplitudes.

36 MATERIALS SCIENCE↗

Thermodynamic analysis and atomistic modeling of subsurface cavitation in photomechanical spallation

According to the article, the thermodynamic conditions defining the spatial extent of a subsurface region affected by the nucleation and growth of voids in photomechanical spallation of metals is investigated theoretically and in atomistic simulations. A theoretical analysis of cavitation in a surface region of a target melted by laser irradiation suggests a functional form for the temperature dependence of the cavitation threshold. A series of small-scale molecular dynamics simulations performed for Al, Ag, Cr, and Ni has revealed the minimum value of the free energy barrier that results in the onset of cavitation on the timescale of 10s of ps, which is a typical duration of transient tensile stresses produced by the unloading wave generated in the spallation regime. The predictive ability of the theoretical description is verified in large-scale simulations of photomechanical spallation of a Ni target and ablation of an Al target in the phase explosion regime. The temporal and spatial evolution of the free energy barrier for the onset of cavitation under conditions of short pulse laser processing is shown to univocally define the region where the nucleation of voids takes place.

Materials Science↗

Experimental investigation on the effects of fabric architectures on mechanical and damage behaviors of carbon/epoxy woven composites

The mechanical behaviors and damage evolutions of carbon/epoxy woven fabric composites with three different geometries, i.e., one plain weave and two twill weave patterns with different areal densities, are studied under tensile loading. The effects of weave patterns on mechanical properties are investigated by monotonic and cyclic tension tests. Remarkable variations in stress–strain curve, Poisson’s ratio, residual strain and strain map exist in the three composites. Crimp ratio is found to be a critical factor to govern the mechanical properties. With smaller crimp ratio, a quasi-linear stress–strain curve with higher elastic modulus and strength is observed. The stress–strain curves of composites with higher crimp ratio contain transition stages with significant tangent modulus degradation. Elastic modulus, strength and damage initiation are all correlated with the crimp ratio linearly regardless of the fabric pattern. Dramatic nonlinear evolution in Poisson’s ratio occurs in the composite with higher crimp ratio. Cyclic tension results indicate that the residual strain is a more appropriate damage indicator than the unloading elastic modulus. Microstructure examination shows that damage developments are essentially related to the fabric geometry, and result in various mechanical behaviors. This work provides important insights into the geometry-deformation mechanism-mechanical property relationship of the woven composites.

36 MATERIALS SCIENCE↗

The physics of desiccation cracks 1: Ductile fracturing and dependence on relative humidity

Ductile deformation is ubiquitously found in the shrinkage of geomaterials. The existence of ductility requires elastoplastic mechanics when analyzing the structure deformation under external stress. Here, in this work, we explore the physics of ductile fracturing based on the results from desiccation experiments and triaxial tests. By using the digital image correlation (DIC) method to generate the strain maps of samples undergoing desiccation cracking under different relative humidities, we obtain results showing the previously postulated Cnoidal Wave ductile failure patterns propagating under atmospheric condition-controlled crack velocities. We then correlate these observations with rate-dependent plasticity models calibrated through triaxial tests undergoing several unloading–reloading cycles and velocity stepping. This work demonstrates the necessity to consider ductility in soil cracking, indicating that the formation of crack patterns in soil desiccation is a slow and predictable process.

58 GEOSCIENCES↗

Deformation-induced spatiotemporal fluctuation, evolution and localization of strain fields in a bulk metallic glass

Deformation behavior and local strain evolutions upon loading and unloading of a bulk metallic glass (BMG) were systematically investigated by in situ digital image correlation (DIC). Distinct fluctuations and irreversible local strains were observed before the onset of macroscopic yielding. Statistical analysis shows that these fluctuations might be related to intrinsic structural heterogeneities, and that the evolution history and characteristics of local strain fields play an important role in the subsequent initiation of shear bands. Effects of sample size, pre-strain, and loading conditions were systematically analyzed in terms of the probability distributions of the resulting local strain fields. It is found that a higher degree of local shear strain heterogeneity corresponds to a more ductile stressestrain curve. Implications of these findings are discussed for the design of new materials.

36 MATERIALS SCIENCE↗

A crystal plasticity model incorporating the effects of precipitates in superalloys: Application to tensile, compressive, and cyclic deformation of Inconel 718

An elasto-plastic polycrystal plasticity model is developed and applied to an Inconel 718 (IN718) superalloy that was produced by additive manufacturing (AM). The model takes into account the contributions of solid solution, precipitates shearing, and grain size and shape effects into the initial slip resistance. Non-Schmid effects and backstress are also included in the crystal plasticity model for activating slip. The hardening law for the critical resolved shear stress is based on the evolution of dislocation density. In using the same set of material and physical parameters, the model is compared against a suite of compression, tension, and large-strain cyclic mechanical test data applied in different AM build directions. We demonstrate that the model is capable of predicting the particularities of both monotonic and cyclic deformation to large strains of the alloy, including decreasing hardening rate during monotonic loading, the non-linear unloading upon the load reversal, the Bauschinger effect, the hardening rate change during loading in the reverse direction as well as plastic anisotropy and the concomitant microstructure evolution. It is anticipated that the general model developed here can be applied to other multiphase alloys containing precipitates.

36 MATERIALS SCIENCE↗

Deformation twinning and detwinning in extruded Mg-4Al: In-situ experiment and crystal plasticity simulation

Deformation twinning and detwinning in extruded Mg-4Al were investigated using in-situ SEM-DIC experiments and crystal plasticity finite element (CPFE) simulation. In this study, the in-situ SEM-DIC method was used to provide a unique set of data including twin/detwin characteristics and twin area fraction in addition to strain maps. A statistical analysis of the activation of twin variants and twin area fraction during both twinning and detwinning was conducted. A strong correlation was found between twin growth/shrinkage and the Schmid Factor (SF) for individual twin variants Higher twin SF during loading and unloading led to higher twin growth and shrinkage, respectively. However, after the applied compressive strain was removed, the pattern of the twin area fractions of the residual twin variants versus their nominal SFs did not follow the trend observed at the maximum compressive strain. Using a systematic methodology and an advanced twin/detwin model, the PRISMS-Plasticity CPFE simulation was calibrated using experimentally determined stress versus strain and twin area fraction versus strain information. A comprehensive evaluation of the CPFE model was conducted to determine its ability to capture the statistics of twin variants activation and twin area fraction. CPFE accurately captured the statistical aspects of both twinning and detwinning. Finally, it also predicted the first dominant twin variant for 47.5% of the grains and at least one of the two dominant twin variants for 80% of the grains at maximum compressive strain.

36 MATERIALS SCIENCE↗

Statistical evaluation of microscale stress conditions leading to void nucleation in the weak shock regime

Here, we investigate the heterogeneity of the stress state driven by anisotropic deformation response at the single crystal level through five statistical volume element (SVE) calculations of polycrystalline BCC tantalum. This work focuses on grain boundaries as a prominent material defect type prone to void nucleation based upon experimental observations of predominantly intergranular void nucleation in this material. The SVEs are constructed to be statistically representative of larger volumes of material and are meshed such that mean and standard deviation of grain size and orientation information is reconstructed. The computational meshes feature hexahedral (brick) elements and smooth conformal grain boundaries where significant stress concentration is known to occur, a tail effect of interest in the extreme events process of dynamic ductile damage. An existing micromechanical crystallographic plasticity model shown to capture the single crystal behavior of BCC tantalum well is used to perform the polycrystal calculations. The model includes representation of the non-Schmid effect of non-planar screw dislocation kinetics in tantalum. A three-dimensional stress state time profile predicted by damage modeling of a flyer plate impact experiment is applied as boundary conditions to each SVE. Resulting grain boundary stress state statistics are strongly non-Gaussian. Significant structural evolution is observed within the compressive hold before unloading into tension in the stress profile. Strong angular dependence of grain boundary traction magnitude with shock direction is observed. Non-Schmid effects continue to suggest their influence on propensity of microstructural defect types to nucleate voids. A general void nucleation criterion is proposed using probability theory. The general framework is specified to polycrystalline BCC tantalum in the weak shock regime to include the SVE calculations and literature molecular dynamics calculations of grain boundary void nucleation strength. Probability density functions (PDFs) are used to describe the interaction between the local stress state heterogeneity and the distributed grain boundary void nucleation strength state. A causation entropy maximization procedure removes the requirement for ad hoc selection of a PDF functional form and provides a rigorous procedure for data-based PDF determination. The resulting physically informed PDF describes the spatial appearance frequency of nucleated voids as a function of applied macroscale pressure. Lower length scale physics are thus packaged in a precise and computationally efficient way to provide computational plasticity insight to macroscale dynamic ductile damage models.

36 MATERIALS SCIENCE↗

An analytical elastic plastic contact model with strain hardening and frictional effects for normal and oblique impacts

Impact between metallic surfaces is a phenomenon that is ubiquitous in the design and analysis of mechanical systems. We found that to model this phenomenon, a new formulation for frictional elastic–plastic contact between two surfaces is developed. The formulation is developed to consider both frictional, oblique contact (of which normal, frictionless contact is a limiting case) and strain hardening effects. The constitutive model for normal contact is developed as two contiguous loading domains: the elastic regime and a transitionary region in which the plastic response of the materials develops and the elastic response abates. For unloading, the constitutive model is based on an elastic process. Moreover, the normal contact model is assumed to only couple one-way with the frictional/tangential contact model, which results in the normal contact model being independent of the frictional effects. Frictional, tangential contact is modeled using a microslip model that is developed to consider the pressure distribution that develops from the elastic–plastic normal contact. This model is validated through comparisons with experimental results reported in the literature, and is demonstrated to be significantly more accurate than 10 other normal contact models and three other tangential contact models found in the literature.

36 MATERIALS SCIENCE↗

Prediction and demonstration of periodic tensile cracking in rate-dependent porous cement

Periodic dilation bands are shown to occur when cylinder-shaped saturated cement specimens are subjected to rapid decompression, with the spacing between the bands scaling as a power law of the decompression time. This behavior is predicted by theory, which is specified to this scenario based on prior work that was more general and applied to compaction. Specifically, the formation of the bands is shown to coincide with periodicity that naturally arises in the effective stress when the material follows a Terzaghi-type consolidation law, although in reverse for dilation and with material deformation described by a rate-dependent viscoplastic law. When strain rate is proportional to effective stress to a power that is greater than one, periodic regions of tensile effective stress arise through the poromechanical fluid-solid coupling. The theoretically-predicted exponent of the resulting power-law relationship between dilation band spacing and unloading time successfully brackets the experimental results, for which it is observed that the exponent is slightly stronger than a square-root relationship (0.28 to 0.67) at testing temperatures of 20 °C and 90 °C. Further, these results demonstrate that rapid-depressurization leads to periodic fracturing that could, on the one hand, be detrimental to the isolation provided by cement used to seal wellbores in the petroleum industry. On the other hand, the dilation bands could also be favorable to production if generated in low-permeability reservoir rocks such as shales that are targeted for petroleum production or granites that are targeted for geothermal energy.

36 MATERIALS SCIENCE↗

Investigation of deformation twinning under complex stress states in a rolled magnesium alloy

We employed a specially designed semi-circular notch specimen in the current study to generate the various strain conditions, including uniaxial, biaxial, shear, and plane strains, which was utilized to explore the evolution of different deformation twinning systems under complex loading conditions. We found that when using in situ synchrotron X-ray diffraction mapping method, that the extensive double twins were activated during loading, while nearly no extension twinning activity was detected. After the formation of {10.1} and {10.3} compression twins, they transformed into {10.1}-{10.2} and {10.3}-{10.2} double twins instantaneously at the early stage of deformation. The lattice strain evolutions in different hkls were mapped at selected load levels during the loading-unloading sequence. Finally, the relationship between the macroscopic straining and microscopic response was established.

36 MATERIALS SCIENCE↗

Achieving ultra-high bearing strength of tungsten nanoribbons in a transforming metal matrix

Nanowires (or nanoribbons) were identified as the most potential structural reinforcements for composites due to their ultrahigh strength, but it is difficult to transcribe their ultrahigh strength into the composite. Here, an in-situ W nanoribbbons-NiTi matrix composite was fabricated by mechanical reduction of a W-NiTi ingot, and the micromechanical deformation behavior was studied by in-situ high energy X-ray diffraction during tensile loading-unloading. It is revealed that the large elastic deformation of the W nanoribbons in a NiTi matrix is dictated by and synchronized with the martensitic transformation of the matrix. The bearing strength of the W nanoribbons, up to 11.6 GPa, was achieved in this composite. A significant load transfer took place from the matrix to the nanoribbons, exhibiting the characters of locality and rapidity. In conclusion, the stress fraction carried by the W nanoribbons with the volume fraction of 3% is up to 45% for the strength of the composite.

36 MATERIALS SCIENCE↗

Modeling and sensitivity analysis of electron capacitance for Geobacter in sedimentary environments

In situ stimulation of the metabolic activity of Geobacter species through acetate amendment has been shown to be a promising bioremediation strategy to reduce and immobilize hexavalent uranium [U(VI)] as insoluble U(IV). Although Geobacter species are reducing U(VI), they primarily grow via Fe(III) reduction. Unfortunately, the biogeochemistry and the physiology of simultaneous reduction of multiple metals are still poorly understood. A detailed model is therefore required to better understand the pathways leading to U(VI) and Fe(III) reduction by Geobacter species. Based on recent experimental evidence of temporary electron sinks in Geobacter we propose a novel kinetic model that physically distinguishes Geobacter species into neutral and electron-charged states. This model shows that the existence of an electron load-unload cycle might be responsible for efficient U(VI) reduction, and elucidates the relationship between U(VI) and Fe(III)-reducing activity and further explains the correlation of high U(VI) removal with high proportions of Geobacter species in a planktonic state in groundwater. Global sensitivity analysis was used to validate the beneficial effects of electron capacitance and determine the level of importance and interactions of physicochemical and biogeochemical processes controlling Geobacter growth and U(VI) reduction. As compared with current modeling approaches in which biomass is often assumed to maintain the same metabolic state over all conditions, the structured two-state model accounts for important aspects of the dynamic electron capacitance of subsurface Geobacter, thereby facilitating further applications in the optimal bioremediation design strategy.

09 BIOMASS FUELS↗

A finite viscoelastic constitutive model for low to high strain rate response of elastomers with application of strain rate-induced glass transition

Amorphous elastomers exhibit significant rate-stiffening and unique viscous flow characteristics across a wide range of strain rates, often undergoing glass transition above a strain rate threshold. We have developed a thermodynamically-consistent and micromechanically-inspired constitutive model for soft elastomeric materials to capture the rate-dependent stress-strain behavior and hysteresis when subjected to low to high strain rates. Here, our proposed constitutive model encapsulates the viscous flow of materials through molecular motion at low strain rates and local rearrangement and alignment of the molecules trying to overcome the intermolecular resistance at high strain rates, essentially covering the glass transition. We applied our constitutive model to uniaxial compression experiments performed at low and high strain rates for polyborosiloxane (PBS) to identify the material parameters, and subsequently, performed numerical simulations of single and multi-cycle compression, stress relaxation, and small amplitude oscillatory tension-compression. Our analyses indicate that the model predicts higher total energy dissipation with increasing strain rate; however, dissipation associated with molecular relaxation decreases (forming a cusp) because, beyond a crossover strain rate, intermolecular rearrangement and alignment become dominant, which is consistent with the onset of the glass transition. For cyclic loading-unloading, we observed that dissipation over a cycle remains constant at low strain rates but decreases non-monotonically at high strain rates before becoming constant, with the peak stress over the cycle becoming higher, which can be interpreted as more loading being carried elastically by the polymer network as the intermolecular rearrangement process occurs. Additionally, our model was able to predict the qualitative nature of the storage modulus and loss modulus in the limit of small strain over a wide range of frequency sweeps.

36 MATERIALS SCIENCE↗

Sugar transporters in grasses: Function and modulation in source and storage tissues

Carbohydrate partitioning, the process of transporting carbohydrates from photosynthetic (source) tissues, such as leaves, to non-photosynthetic (sink) tissues, such as stems, roots, and reproductive structures, is vital not only for the growth and development of plants but also for withstanding biotic and abiotic stress. In many plants, sucrose is the primary form of carbohydrate loaded into the phloem for long-distance transport and unloaded into the sink tissues for utilization or storage. Here, we highlight recent findings about 1) phloem loading in grasses, 2) the principal families of sugar transporters involved in sucrose transport, and 3) novel mechanisms by which the activities of sugar transporters are modulated. We discuss exciting discoveries from eudicot species that provide valuable insights regarding the regulation of these sugar transporters, which may be translatable to monocot species. As we better understand the intricate pathways that control the activities of various sugar transporters, we can utilize this knowledge for developing improved crop varieties.

59 BASIC BIOLOGICAL SCIENCES↗

Mechanical behavior and electrical conductivity of La1-xCaxCoO3 (x = 0, 0.2, 0.4, 0.55) perovskites

This paper compares the important mechanical properties and the electrical conductivities from room temperature to 800oC of four LaCoO3 based cobaltite compositions with 0, 20, 40 and 55% Ca2+ ions substituted on the A site of the perovskite structure respectively. Ca2+ doped lanthanum cobaltite materials are strong candidates for use as cathodes in lower temperature solid oxide fuel cells operating at or below 800oC. Among these four cobaltite compositions, two (LaCoO3 and La0.8Ca0.2CoO3) were found to be phase pure materials, whereas the remaining two compositions (La0.6Ca0.4CoO3 and La0.45Ca0.55CoO3) contained precipitation of secondary phases such as CaO and Co3O4. The mechanical properties of the four compositions, in terms of Young s modulus, four-point bending strength and fracture toughness measurements, were measured at both room temperature and 800oC. At room temperature, doping with Ca2+ was found to substantially increase the mechanical properties of the cobaltites, whereas at 800oC the pure LaCoO3 composition exhibited higher modulus and strength values than La0.8Ca0.2CoO3. All of the four compositions exhibited ferroelastic behavior, as shown by the hysteresis loops generated during uniaxial load-unload compression tests. Electrical conductivity measurements showed the La0.8Ca0.2CoO3 composition to have the highest conductivity among the four compositions.

30 DIRECT ENERGY CONVERSION↗

Geodetic imaging of thermal deformation in geothermal reservoirs - production, depletion and fault reactivation

Here, we investigate thermally induced surface deformation in geothermal systems. To define source mechanisms at depth, we assess the mechanical process of subsurface deformation by assuming a spherically cooled fractured reservoir in an infinite medium and derive relations that define magnitudes of thermal contraction, stress change and permeability evolution. The magnitude of thermal deformation in typical geothermal system is larger than anticipated and suggests two different modalities of surface subsidence – thermal contraction and fault reactivation. Here, surface deformation (vertical displacement, surface tilt and horizontal strain) induced by the two different modalities are assessed with Mogi (contraction) and Okada (slip) models and compared with instrumental sensitivity of high precision surface geodetic tools. Here, we show that 1 year of geothermal operation at 10 MW with a power plant conversion efficiency of 12% can yield ~ 3.0 × 10 4 m 3 of subsurface volume change. For a reservoir at 2000 m depth, this induces ~ 1.7 mm of vertical surface displacement, ~ 800 nano-radians of surface tilt and ~ 900 nano-strains of surface strain. This result implies that typically observed magnitudes of surface subsidence (order of cm/year) are naturally expected in massive (100 MW scale) geothermal operations and observed surface subsidence may largely be the result of thermal contraction. Conversely, thermal unloading can trigger fault reactivation. Analysis with an Okada slip model shows these shear offsets on pre-existing faults can also result in surface deformations of considerable magnitude. Our analysis of field operational data from various geothermal projects suggests that both thermal contraction and slow fault reactivation may contribute to the observed large surface deformation. Comparison of predicted deformation with instrumental sensitivity of high precision surface tools confirms that geodetic signals, especially tilt and strain, are indeed sufficiently large to describe reservoir evolution and to potentially deconvolve reservoir parameters of interest, such as permeability.

15 GEOTHERMAL ENERGY↗