Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transients (Dynamics)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Correlating armature and needle dynamics with voltage waveforms of solenoid-actuated GDI injector

The injector voltage hump that appears near the needle closing has been used for the real-time monitoring and feedback control of fuel injection duration in modern engines. This voltage hump has been thought to result from the abrupt change in electromagnetic induction by the stoppage of needle motion but detailed electromagnetic processes and associated armature and needle dynamics during the needle closing have not been thoroughly investigated in a wide range of injection conditions, which knowledge is crucial for the delicate control of fuel injection based on the voltage hump. Here, the current study analyzes the transient armature and needle dynamics of a solenoid-actuated gasoline direct injection injector using an X-ray phase-contrast imaging technique. Then, the results are correlated with voltage waveforms during the needle closing transient under various injection pressures, injection pulse durations, and dwell times of split injections. The time derivatives of voltage waveforms showed lower and upper peaks in order in the regime of the voltage hump. Inconsistent with conventional understandings, the lower peak timing of the voltage derivative did not match with the timing of needle closing (end of injection) but rather matched with the abrupt descent timing of the armature and needle. The inflection timing and upper peak timing of the voltage derivative matched with the timings of actual needle closing and armature closing respectively. The amplitude of the voltage hump was near linearly dependent on the needle closing speed. The needle closing speed decreased upon the decrease of injection pulse duration and injection pressure which made it difficult to detect the voltage humps in ballistic injection regimes and low injection pressures. In split injection conditions, the voltage hump of the first injection was not detectable if the dwell time was shorter than the needle closing delay, the time from the current cut-off to the actual needle closing.

42 ENGINEERING↗
NASA NTRS1982

Application of the Hughes-LIU algorithm to the 2-dimensional heat equation

An implicit explicit algorithm for the solution of transient problems in structural dynamics is described. The method involved dividing the finite elements into implicit and explicit groups while automatically satisfying the conditions. This algorithm is applied to the solution of the linear, transient, two dimensional heat equation subject to an initial condition derived from the soluton of a steady state problem over an L-shaped region made up of a good conductor and an insulating material. Using the IIT/PRIME computer with virtual memory, a FORTRAN computer program code was developed to make accuracy, stability, and cost comparisons among the fully explicit Euler, the Hughes-Liu, and the fully implicit Crank-Nicholson algorithms. The Hughes-Liu claim that the explicit group governs the stability of the entire region while maintaining the unconditional stability of the implicit group is illustrated.

Malkus, D. S.↗
DOE OSTI2020

Anisotropic X-Ray Scattering of Transiently Oriented Water

We study the structural dynamics of liquid water by time-resolved anisotropic x-ray scattering under the optical Kerr effect condition. In this way, we can separate the anisotropic scattering decay of 160 fs from the delayed temperature increase of ~ 0.1 K occurring at 1 ps and quantify transient changes in the O-O pair distribution function. Polarizable molecular dynamics simulations reproduce well the experiment, indicating transient alignment of molecules along the electric field, which shortens the nearest-neighbor distances. In addition, analysis of the simulated water local structure provides evidence that two hypothesized fluctuating water configurations exhibit different polarizability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Development of k{sub eff} in the unfolding process of the LOTUS reactor design

An innovative small thermal reactor concept named LOTUS, which is a pool-type reactor aimed at heat supply. The passive concept applied in the LOTUS and it has a separable core. It means that its core can passively unfold into four parts along its central axis only with the buoyancy and gravity when some accidents happen, especially the wall rupture of the pool caused by earthquake, aircraft impact and so on. This idea can effectively enhance the ability of pool-type reactor for resisting some severe accidents. We have executed some pre-computations in order to check a non-supercritical system for the transient simulation. In this paper, the development of k{sub eff} have been calculated by both stepwise steady-state and transient modes using Serpent, as well as including some sensitivity analyses about the k{sub eff} to unfolding velocity, inserting velocity of control rod (CR) and time step. The result showed that k{sub eff} value decreased definitely as the reactor unfolded and the consistent change exposed between the stepwise steady state and transient result when the unfolding angle varied from 0 to 1 degree. However, the stepwise steady state k{sub eff} negatively declined after that angle, which demonstrated that for such a dynamic unfolding change the transient mode was more suitable, peculiarly for considering delayed neutrons and neutron moderation. For sensitivity calculation, the k{sub eff} decreased more rapidly as the unfolding velocity and inserting velocity of CR increased, and a smaller time step corresponded to a more stable change. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Accelerating transients with NekRS: GPU overlapping domain implementation and multi-rate timestepping

The simulation of nuclear transients using Computational Fluid Dynamics (CFD) presents significant computational challenges due to the inherent complexity and the wide separation in temporal scales between various flow physical phenomena. These disparities lead to high computational costs, often making the simulation of transients impractical without advanced techniques. Consequently, multiple research initiatives are being pursued by the NEAMS thermal-hydraulic area, some driven by academic institutions and some by national laboratories. Overall, they are exploring novel methods to make transient simulations more feasible and efficient. This report delves into recent advancements within the CFD code NekRS, specifically those achieved in Fiscal Year 2024 under the CONNECT effort, aimed at improving the performance and feasibility of transient simulations. The first major advancement involves the porting of NekRS to Aurora, one of the Department of Energy’s (DOE) most powerful supercomputers. Additionally, the report discusses the implementation of an overlapping domain capability within NekRS. This novel GPU-accelerated capability allows different spatial regions of the domain to be solved independently, enhancing the code’s efficiency, particularly when running large-scale simulations in complex domains. The scalability of this approach is demonstrated, highlighting its potential to transform how transients are approached in CFD simulations. Lastly, the report focuses on how this overlapping domain capability specifically accelerates transient simulations through multi-rate timestepping. By decoupling different regions and facilitating faster computations, this method offers a promising pathway to making nuclear transient simulations more computationally feasible, addressing one of the critical bottlenecks in the field. Together, these advancements represent a significant leap forward in transient simulation technology, bringing closer the possibility of handling highly complex nuclear scenarios with greater efficiency and accuracy.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Hindered segmental dynamics in associative protein hydrogels studied by neutron spin-echo spectroscopy

Transient binding between associating macromolecules can cause qualitative changes to chain dynamics, including modes of conformational relaxation and diffusion, through tethering effects imparted by long-range connectivity. Here, in this work, the role of binding on short-time segmental dynamics in associative polymer gels is investigated by neutron spin-echo (NSE) measurements on a class of model artificial coiled-coil proteins with a systematically varied architecture, probing timescales of 0.1–130 ns, and length scales close to the molecular radius of gyration. The results illustrate effects of transient cross-linking on chain dynamics on different timescales, manifested in changes in segmental relaxation behavior with variations in strand length, chain concentration, and sticker distribution (endblock- vs midblock-functionalized). In all gels, a short-time cooperative diffusion mode is seen over all wave vectors, analogous to a semidilute solution, with no transitions seen at any known structural length scale. However, the diffusion coefficients are found to decrease with increasing junction density across all gels, with the strand length and number of stickers per chain in each gel appearing to play a relatively minor role. The slowing of cooperative diffusion with junction density contrasts with classical predictions of a greater restoring force for fluctuation dissipation due to the increased elasticity, suggesting additional effects of the coiled-coil junctions such as an enhancement in local viscosity that slows dynamics. Notably, the relaxation rates for all gels can be rescaled by the interjunction spacing inferred from small-angle neutron scattering, where they collapse onto a master curve suggestive of self-similar dynamics even in networks with different strand lengths and chain architectures. On long timescales (but shorter than the junction exchange time), a slowing of network relaxation is observed, resulting in a nondecaying plateau in the spin-echo amplitude attributed to a freezing of chain dynamics due to tethering. A characteristic length scale corresponding to the extent of dynamic fluctuations is estimated for each gel, which appears to be smaller than the interjunction spacing but similar to the correlation blob size of the overlapping strands. The results indicate an important role of transient binding on molecular-scale dynamics in associative polymer gels, even on timescales shorter than the junction exchange time, in addition to its effects on long-range self-diffusion previously observed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Assessing the Impact of a Novel TBC Material on Heat Transfer in a Spark Ignition Engine through 3D CFD-FEA Co-Simulation Routine

Thermal barrier coatings (TBCs) have been of interest since the 1970s for application in internal combustion (IC) engines. Thin TBCs exhibit a temperature swing phenomenon wherein wall temperatures dynamically respond to the transient working-gas temperature throughout the engine cycle, thus reducing the temperature difference driving the heat transfer. Determining these varying wall temperatures is necessary to evaluate and study the effect of coatings on wall heat transfer. This study focuses on developing a 3D computational fluid dynamics (CFD)-finite element analysis (FEA) coupled simulation, or co-simulation, routine to determine the wall temperatures of a piston coated with a thin TBC layer subject to spark ignition combustion heat flux. A CONVERGE 3D-CFD model was used to simulate the combustion process in a single-cylinder, light-duty experimental spark ignition (SI) engine. Transient piston heat transfer analysis was conducted using ABAQUS, a FEA package, under the simulated combustion heat flux load. The effect of the temperature swing phenomenon due to this TBC layer was observed in a CFD simulation by implementing the FEA results as the piston thermal boundary conditions. The boundary conditions were passed between the CFD and FEA tools until a quasi-steady state solution was achieved. Furthermore, a reduction in wall heat transfer was observed due to a reduced temperature difference between the wall and the working gas.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1979

Experimental Investigation of Launch Vehicle Transient Input Simulation in Payload Tests

The technique of electronically simulating the structural dynamics of a launch vehicle in transient tests of payloads using multiple vibration excitation systems was investigated. The development of computer programs to determine transfer functions, synthesize shaker forcing functions, and control vibration exciters is described. A demonstration test using the techniques was described and results are presented. The evaluation of the potential for applying this technique to large Shuttle payloads is discussed.

Rader, P.↗
NASA NTRS2021

Transient evolution of basal drag during glacier slip

Glacier slip is usually described using steady-state sliding laws that relate drag, slip velocity and effective pressure, but where subglacial conditions vary rapidly transient effects may influence slip dynamics. Here we use results from a set of laboratory experiments to examine the transient response of glacier slip over a hard bed to velocity perturbations. The drag and cavity evolution from lab experiments are used to parameterize a rate-and-state drag model that is applied to observations of surface velocity and ice-bed separation from the Greenland ice sheet. The drag model successfully predicts observed lags between changes in ice-bed separation and sliding speed. These lags result from the time (or displacement) required for cavities to evolve from one steady-state condition to another. In comparing drag estimates resulting from applying rate-and-state and steady-state slip laws to transient data, we find the peaks in drag are out of phase. This suggests that in locations where subglacial conditions vary on timescales shorter than those needed for cavity adjustment transient slip processes control basal drag.

Glacier↗
DOE OSTI2021

Excited-state structural dynamics of nickel complexes probed by optical and X-ray transient absorption spectroscopies: insights and implications

Excited states of nickel complexes undergo a variety of photochemical processes, such as charge transfer, ligation/deligation, and redox reactions, relevant to solar energy conversion and photocatalysis. The efficiencies of the aforementioned processes are closely coupled to the molecular structures in the ground and excited states. The conventional optical transient absorption spectroscopy has revealed important excited-state pathways and kinetics, but information regarding the metal center, in particular transient structural and electronic properties, remains limited. These deficiencies are addressed by X-ray transient absorption (XTA) spectroscopy, a detailed probe of 3d orbital occupancy, oxidation state and coordination geometry. The examples of excited-state structural dynamics of nickel porphyrin and nickel phthalocyanine have been described from our previous studies with highlights on the unique structural information obtained by XTA spectroscopy. Furthermore, we close by surveying prospective applications of XTA spectroscopy to active areas of Ni-based photocatalysis based on the knowledge gained from our previous studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Multi-Timescale Integrated Dynamic and Scheduling Model (MIDAS-Solar)

Solar photovoltaic (PV) installations have experienced unprecedented growth in the United States. PV will become not only an energy producer but also a necessary provider of ancillary services at multiple timescales. Conventional methods to simulate power system operations - such as long-term production simulation (which typically considers schedules from hours to minutes by using an optimization framework) and short-term transient studies (which simulate dynamics from seconds to sub-seconds using state variables and differential equations) are not sufficient for studying the multiple-timescale variation of solar generation and its impact on system reliability. Long-term system economics and short-term system dynamics are highly coupled, particularly when the penetration level of renewable generation is extremely high, because the uncertainty and variability of solar generation will impact both power systems steady-state and dynamic performance. This project helps meet and exceed the Solar Energy Technologies Office goal of systems integration by directly addressing this stability and reliability challenge for electric grid planning and operation. This will be accomplished by developing temporally comprehensive, closed-loop simulation models that seamlessly simulate power systems operations from economic scheduling (day-ahead to hours) to dynamic response analysis (seconds to sub-seconds). Both a multi-timescale grid model and an integrated PV model will be developed in this project to accurately study the impacts of PV variability and uncertainty on system reliability at multiple timescales. Using quasi-dynamic simulation methods and data-driven security assessment (DSA) criteria will allow the dynamic characteristics of PV to be fed forward into longer-timescale scheduling models for a complete understanding of the effect of short-term PV dynamics on bulk systems operations (e.g., reserve scheduling and deployment). Upon completion of the proposed model, this project will help operators accurately assess system reliability by deploying energy and reserve scheduling under critical contingency conditions and studying interactions among all types of essential reliability services provided by modern PV power plants.

14 SOLAR ENERGY↗
NASA NTRS1972

The effect of support flexibility and damping on the dynamic response of a single mass flexible rotor in elastic bearings

The dynamic unabalance response and transient motion of the single mass Jeffcott rotor in elastic bearings mounted on damped, flexible supports are discussed. A steady state analysis of the shaft and the bearing housing motion was made by assuming synchronous precession of the system. The conditions under which the support system would act as a dynamic vibration absorber at the rotor critical speed were studied. Plots of the rotor and support amplitudes, phase angles, and forces transmitted were evaluated by the computer and the performance curves were plotted by an automatic plotter unit. Curves are presented on the optimization of the support housing characteristics of attenuate the rotor synchronous unbalance response.

Kirk, R. G.↗
NASA NTRS1989

Enhanced element-specific modal formulations for flexible multibody dynamics

The accuracy of current flexible multibody formalisms based on assumed modes is examined in the context of standard spacecraft motions involving structural components undergoing both slow and fast overall translational and rotational motions as well as small deformations. Limitations of current techniques in treating: (1) element-specific coupling behavior of large motion and small deformation, and (2) motion-induced structural stiffness variations, are noted. The roles of nonlinear and linear elastic structural theories in accurately predicting transient large-displacement dynamic behavior of flexible multibody systems are examined in detail. Coupling effects between deformation and overall motion are carefully scrutinized in the context of assumed-mode discretization techniques. Consistently linearized beam, plate, and shell formulations involving in-plane stretch variables are proposed and shown to yield very accurate simulation results and extremely fast modal convergence for most motions involving small strains. In some particular cases, however, in which membrane stiffness dominates bending stiffness, a nonlinear strain formulation is required in order to capture proper coupling between deformation and overall motion.

Ryan, Robert R.↗
DOE OSTI2024

Energy Level Gradients from Surface to Bulk in Hybrid Metal-Halide Perovskite Thin Films

Variations in local strain, defect densities, and composition of hybrid metal-halide perovskites have been reported to create heterogeneous energy landscapes in thin films, which impact charge-carrier diffusion and recombination dynamics. Here, we employ one- and two-photon transient absorption spectroscopy to selectively probe the dynamics of charge carriers from surface and bulk regions of methylammonium lead bromide thin films. Differences in the transient absorption spectra indicate that an energy gradient of approximately 100 meV is formed between the higher band-gap surface and lower band-gap bulk regions. Thus, during their lifetime, photoexcited carriers move away from the surface to recombine in the bulk, where our experiments detect long-lived charge populations despite the significant band splitting that has conventionally been assumed to inhibit efficient radiative recombination. Supported by first-principles calculations, we demonstrate that bright emission can still arise from the bulk with states that occupy a wide range of momenta in the vicinity of the band extrema, which show strong dipole transitions. Our results report that photoexcitations in the hybrid perovskites avoid defect-rich surface regions, and that particularly strong emission is generated from accumulated excitation populations in the bulk. Published by the American Physical Society 2024

Bourelle, Sean A.↗
DOE OSTI2021

Transmission-and-Distribution Dynamic Co-simulation Framework for Distributed Energy Resource Frequency Response

The rapid deployment of distributed energy resources (DERs) in distribution networks has made it challenging to balance the transmission system and stabilize frequency. DERs have the ability to provide frequency regulation services; however, existing frequency dynamic simulation tools - which were developed mainly for the transmission system - lack the capability to simulate distribution network dynamics with high penetrations of DERs. Although electromagnetic transient simulation tools can simulate distribution network dynamics, the computation efficiency limits their use for large-scale transmission-and-distribution (T&D) co-simulation. This paper presents an efficient open-source T&D dynamic co-simulation framework for DER frequency response based on the HELICS platform and off-the-shelf T&D simulators. The challenge of synchronizing the simulation time between the transmission network and the DERs in the distribution network is solved through the detailed modeling of DERs in frequency dynamic models while DER power flow models are also preserved in the distribution networks, thereby respecting local voltage constraints when dispatching DER power for frequency response. DER frequency response (primary and secondary) is simulated in case studies to validate the proposed framework. Last, the accuracy of the proposed co-simulation model is benchmarked, and a large T&D system simulation (2k transmission and 1M distribution nodes) is presented to demonstrate the efficiency and effectiveness of the overall framework.

24 POWER TRANSMISSION AND DISTRIBUTION↗