Frequency-dependent dielectric constant of KH sub 2 PO sub 4.
Frequency and temperature dependent dielectric constant of potassium dihydrogen phosphate above transition temperature, discussing proton tunneling and damping times
Silverman, B. D.↗
SEARCH · Engineering Papers
Results for “TRANSITION TEMPERATURE”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effects of hydrothermal exposure on a low-temperature cured epoxy
Thermal mechanical analysis was employed to monitor the penetration temperature of a low-temperature epoxy resin. Both neat resin and E-glass composite samples were examined. The effects of cure temperature variation and moisture content on the apparent glass transition temperature were determined.
Lauver, R. W.↗
Effects of hydrothermal exposure on a low-temperature cured epoxy
Thermal mechanical analysis was employed to monitor the penetration temperature of a low-temperature epoxy resin (EPON 826/D230). Both neat resin and E-glass composite samples were examined. The effects of cure temperature variation and moisture content on the apparent glass transition temperature were determined.
Lauver, R. W.↗
Liquid crystal polyester-carbon fiber composites
Liquid crystal polymers (LCP) have been developed as a thermoplastic matrix for high performance composites. A successful melt impregnation method has been developed which results in the production of continuous carbon fiber (CF) reinforced LCP prepreg tape. Subsequent layup and molding of prepreg into laminates has yielded composites of good quality. Tensile and flexural properties of LCP/CF composites are comparable to those of epoxy/CF composites. The LCP/CF composites have better impact resistance than the latter, although epoxy/CF composites possess superior compression and shear strength. The LCP/CF composites have good property retention until 200 F (67 % of room temperature value). Above 200 F, mechanical properties decrease significantly. Experimental results indicate that the poor compression and shear strength may be due to the poor interfacial adhesion between the matrix and carbon fiber as adequate toughness of the LCP matrix. Low mechanical property retention at high temperatures may be attributable to the low beta-transition temperature (around 80 C) of the LCP matrix material.
Chung, T. S.↗
Effect of boron on tensile properties of B2 BeAl
Small additions of boron were shown to improve the room temperature ductility of the intermetallic compound Ni3Al. Boron is believed to segregate to the gain boundaries and strengthen them, allowing the inheret ductility of the grains to be achieved. The present study was undertaken to see if boron has a similar effect on the low temperature tensile properties of the equiatomic intermetallic compound FeAl. A binary alloy without boron is compared with an alloy containing 0.78 at % B (0.2 wt %) B, by tensile testing over the temperature range of 300 K to 640 K. Both alloys were processed by powder metallurgy. Results showed that 0.78 at % B addition to FeAl does indeed change the room temperature fracture mode from intergranular to transgranular, suggesting a strengthening of grain boundaries. The alloy containing boron is, however, still brittle at room temperature. A slight decrease in the ductile to brittle transition temperature is, nevertheless, observed. In addition a significant increase in strength of the alloy is observed with boron addition.
Crimp, M.↗
Initial adhesive screening of novel polyamide-imides and their copolymers
Continued interest by the research community in thermally stable, tough, high temperature adhesives has resulted in the investigation by Langley Research Center of two linear aromatic polyamide-imide (PAI) homopolymers and two linear aromatic PAI copolymers. The homopolymers were made with either 3,3'=DABA or 4,4'-DABA and BTDA. The two polymers were prepared with a monomer ratio of 0.75 DABP:0.25 DABA:1.00 BTDA. These aromatic PAIs possess high thermal stability because of intermolecular hydrogen bonding and chain stiffness. Lap shear strength (LSS) was the main criteria used to evaluate the polymers as adhesives. LSS of bonded Ti-6Al-4V was determined at room temperature (RT), 177, 204 and 232 C. The glass transition temperature and the type of bond failure were also determined. The best LSS values of the four adhesive systems investigated were obtained with the PAI copolymer identified in the report as LARC-TPI (25 percent 3,3'-DABA); however, it did not produce LSSs nearly as high as LARC-TPI. The poor flow properties observed appear to be due to a combination of high molecular weight and the increased interchain electronic interactions associated with the amide group.
Donald J Progar↗
Initial evaluation of novel polyamide-imides and their copolymers as adhesives
Continued interest by the research community in thermally stable, tough, high temperature adhesives has resulted in the investigation by Langley Research Center of two linear aromatic polyamide-imide (PAI) homopolymers and two linear aromatic PAI copolymers. The homopolymers were made with either 3,3'=DABA or 4,4'-DABA and BTDA. The two polymers were prepared with a monomer ratio of 0.75 DABP:0.25 DABA:1.00 BTDA. These aromatic PAIs possess high thermal stability because of intermolecular hydrogen bonding and chain stiffness. Lap shear strength (LSS) was the main criteria used to evaluate the polymers as adhesives. LSS of bonded Ti-6Al-4V was determined at room temperature (RT), 177, 204 and 232 C. The glass transition temperature and the type of bond failure were also determined. The best LSS values of the four adhesive systems investigated were obtained with the PAI copolymer identified in the report as LARC-TPI (25 percent 3,3'-DABA); however, it did not produce LSSs nearly as high as LARC-TPI. The poor flow properties observed appear to be due to a combination of high molecular weight and the increased interchain electronic interactions associated with the amide group.
Progar, Donald J.↗
Phase transformations in SrAl2Si2O8 glass
Bulk glass of SrAl2Si2O8 composition crystallized at temperatures below 1000 C into hexacelsian, a hexagonal phase which undergoes a reversible, rapid transformation to an orthorhombic phase at 758 C, and at higher temperatures crystallized as celsian, a monoclinic phase. The glass transition temperature and crystallization onset temperature were determined to be 883 C and 1086 C, respectively, from DSC at a heating rate of 20 C/min. Thermal expansion of the various phases and density and bend strengths of cold isostatically pressed glass powder bars, sintered at various temperatures, were measured. The kinetics of the hexacelsian-to-celsian transformation for SrAl2Si2O8 were studied. Hexacelsian flakes were isothermally heat treated at temperatures from 1025-1200 C for various times. Avrami plots were determined by quantitatively measuring the amount of monoclinic celsian formed at various times using x ray diffraction. The Avrami constant was determined to be 1.1, suggesting a diffusionless, one dimensional transformation mechanism. The activation energy was determined from an Arrhenius plot of 1n k vs. 1/T to be 125 kilocal/mole. This value is consistent with a mechanism which transforms the layered hexacelsian structure to a three dimensional framework celsian structure and involves the breaking of Si-O bonds.
Drummond, Charles H., III↗
New developments in thermally stable polymers
Advances in high-temperature polymers since 1985 are discussed with the emphasis on the chemistry. High-temperature polymers refer to materials that exhibit glass-transition temperatures greater than 200 C and have the chemical structure expected to provide high thermooxidative stability. Specific polymers or series of polymers were selected to show how the chemical structure influences certain properties. Poly(arylene ethers) and polyimides are the two principal families of polymers discussed. Recent work on poly(arylene ethers) has concentrated on incorporating heterocyclic units within the polymer backbone. Recent polyimide work has centered on the synthesis of new polymers from novel monomers, several containing the trifluoromethyl group strategically located on the molecule. Various members in each of these polymer families display a unique combination of properties, heretofore unattainable. Other families of polymers are also briefly discussed with a polymer from an AB maleimidobenzocyclobutene exhibiting an especially attractive combination of properties.
Hergenrother, Paul M.↗
Low cycle fatigue behavior of polycrystalline NiAl at 300 and 1000 K
The low cycle fatigue behavior of polycrystalline NiAl was determined at 300 and 1000 K - temperatures below and above the brittle- to-ductile transition temperature (BDTT). Fully reversed, plastic strain-controlled fatigue tests were conducted on two differently fabricated alloy samples: hot isostatically pressed (HIP'ed) prealloyed powder and hot extruded castings. HIP'ed powder (HP) samples were tested only at 1000 K, whereas the more ductile cast-and-extruded (C+E) NiAl samples were tested at both 1000 and 300 K. Plastic strain ranges of 0.06 to 0.2 percent were used. The C+E NiAl cyclically hardened until fracture, reaching stress levels approximately 60 percent greater than the ultimate tensile strength of the alloy. Compared on a strain basis, NiAl had a much longer fatigue life than other B2 ordered compounds in which fracture initiated at processing-related defects. These defects controlled fatigue life at 300 K, with fracture occurring rapidly once a critical stress level was reached. At 1000 K, above the BDTT, both the C+E and HP samples cyclically softened during most of the fatigue tests in air and were insensitive to processing defects. The processing method did not have a major effect on fatigue life; the lives of the HP samples were about a factor of three shorter than the C+E NiAl, but this was attributed to the lower stress response of the C+E material. The C+E NiAl underwent dynamic grain growth, whereas the HP material maintained a constant grain size during testing. In both materials, fatigue life was controlled by intergranular cavitation and creep processes, which led to fatigue crack growth that was primarily intergranular in nature. Final fracture by overload was transgranular in nature. Also, HP samples tested in vacuum had a life three times longer than their counterparts tested in air and, in contrast to those tested in air, hardened continuously over half of the sample life, thereby indicating an environmentally assisted fatigue damage mechanism. The C+E samples were tested only in air. At 1000 K, NiAl exhibited a superior fatigue life when compared to most superalloys on a plastic strain basis, but was inferior to most superalloys on a stress basis.
Lerch, Bradley A.↗
Tape-Drop Transient Model for In-Situ Automated Tape Placement of Thermoplastic Composites
Composite parts of nonuniform thickness can be fabricated by in-situ automated tape placement (ATP) if the tape can be started and stopped at interior points of the part instead of always at its edges. This technique is termed start/stop-on-the-part, or, alternatively, tape-add/tape-drop. The resulting thermal transients need to be managed in order to achieve net shape and maintain uniform interlaminar weld strength and crystallinity. Starting-on-the-part has been treated previously. This paper continues the study with a thermal analysis of stopping-on-the-part. The thermal source is switched off when the trailing end of the tape enters the nip region of the laydown/consolidation head. The thermal transient is determined by a Fourier-Laplace transform solution of the two-dimensional, time-dependent thermal transport equation. This solution requires that the Peclet number Pe (the dimensionless ratio of inertial to diffusive heat transport) be independent of time and much greater than 1. Plotted isotherms show that the trailing tape-end cools more rapidly than the downstream portions of tape. This cooling can weaken the bond near the tape end; however the length of the affected region is found to be less than 2 mm. To achieve net shape, the consolidation head must continue to move after cut-off until the temperature on the weld interface decreases to the glass transition temperature. The time and elapsed distance for this condition to occur are computed for the Langley ATP robot applying PEEK/carbon fiber composite tape and for two upgrades in robot performance. The elapsed distance after cut-off ranges from about 1 mm for the present robot to about 1 cm for the second upgrade.
Costen, Robert C.↗
Fabrication and Radio Frequency Properties of 3-GHz SRF Cavities Coated with MgB 2
Magnesium diboride (MgB 2 ) is considered a potential material for superconducting radio frequency cavities. MgB 2 coated Cu cavity will allow for a higher operational temperature than a bulk Nb cavity because of the higher transition temperature of MgB 2 and the high thermal conductivity of Cu. Using the hybrid physical chemical vapor deposition technique, MgB 2 coatings were successfully achieved on the inner wall of 3-GHz Cu cavities. The surface and superconducting properties of the coatings were characterized using small samples on Cu plugs mounted at different locations of mock cavities. RF measurement of a MgB 2 coated single-cell 3-GHz test cavity was carried out and it showed superconducting transition at 36 K. Here, the quality factor of this test cavity was lower than expected due to poor connectivity and inclusion of Mg-Cu alloy in the MgB 2 coating.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Pressure-induced high-temperature superconductivity retained without pressure in FeSe single crystals
To raise the superconducting-transition temperature (T c ) has been the driving force for the long-sustained effort in superconductivity research. Recent progress in hydrides with T c s up to 287 K under pressure of 267 GPa has heralded a new era of room temperature superconductivity (RTS) with immense technological promise. Indeed, RTS will lift the temperature barrier for the ubiquitous application of superconductivity. Unfortunately, formidable pressure is required to attain such high T c s. The most effective relief to this impasse is to remove the pressure needed while retaining the pressure-induced T c without pressure. Here, we show such a possibility in the pure and doped high-temperature superconductor (HTS) FeSe by retaining, at ambient pressure via pressure quenching (PQ), its T c up to 37 K (quadrupling that of a pristine FeSe at ambient) and other pressure-induced phases. We have also observed that some phases remain stable without pressure at up to 300 K and for at least 7 d. The observations are in qualitative agreement with our ab initio simulations using the solid-state nudged elastic band (SSNEB) method. We strongly believe that the PQ technique developed here can be adapted to the RTS hydrides and other materials of value with minimal effort.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Reflected shock-initiated ignition probed via simultaneous lateral and endwall high-speed imaging with a transparent, cylindrical test-section
A TRAnsparent cylindrical (TRAC) shock tube test section has been developed to explore the ignition structure behind reflected shockwaves via simultaneous lateral and endwall high-speed imaging using three fuel/oxidizer mixtures: 0.1% n-C 7 H 16 /1.10% O 2 /4.14% N 2 /94.66% Ar, 0.1% iC 8 H 18 /1.25% O 2 /4.69% N 2 /93.96% Ar, and 5% CH 4 /10% O 2 /85% CO 2 . During mild ignition, the first exothermic centers were located outside of the observable test section. It is shown that with increasing temperature the far-wall ignition events move closer to the endwall, until a strong ignition is achieved. The temperature gradients that promote mild ignition were quantified and were found to have a slight dependence on fuel with the RMS temperature gradients being 0.80% for n-heptane and 1.07% for isooctane. The impact of temperature gradients on metrics used to improve kinetic models, such as species time histories, is noteworthy. From this temperature gradient, an experimental correlation is provided to estimate the transition temperature from mild to strong ignition for a mixture. The effect of diagnostic location in non-homogeneous reactions is quantified in reference to ignition delay. In conclusion, the unique and insightful perspective on the ignition process under heavy shock bifurcation is also discussed.
02 PETROLEUM↗
Recent trends in all-organic polymer dielectrics for high-temperature electrostatic energy storage capacitors
Electrostatic energy storage (EES) capacitors are critical for renewable energy and high-power systems, driving the search for dielectric materials that combine superior electrical insulation, mechanical flexibility, low density, cost-effectiveness, and processability. Polymer-based dielectrics have emerged as leading candidates, particularly for high electric field applications. However, conventional polymers often fail to meet the demands of high-temperature environments due to increased electrical conductivity and reduced discharged energy density at elevated temperatures, resulting in energy loss and reduced performance. High glass transition temperature (T g) polymers show promise but require further optimization to enhance their energy storage capabilities under thermal and electrical stress. This review provides a comprehensive update on recent advancements in high-T g polymer-based dielectrics for EES capacitors, focusing on both intrinsic polymers and all-organic composites. It outlines key design principles, critical performance parameters, and innovative strategies—such as nanofiller doping, layered architectures, physical blending, and chemical crosslinking—to improve electrical, thermal, and mechanical properties. The review also highlights emerging trends, including the integration of machine learning algorithms to explore novel polymer structures and expand the chemical design space. By bridging the gap between academic research and industrial application, this review aims to accelerate the development of next-generation dielectric materials capable of balancing multiple performance metrics for high-temperature EES capacitors.
Xie, Zongliang↗
Irradiation damage concurrent challenges with RAFM and ODS steels for fusion reactor first-wall/blanket: a review
Reduced activation ferritic martensitic (RAFM) and oxide dispersion strengthened (ODS) steels are the most promising candidates for fusion first-wall/blanket (FW/B) structures. The performance of these steels will deteriorate during service due to neutron damage and transmutation-induced gases, such as helium/hydrogen, at elevated operating temperatures. Here, after highlighting the operating conditions of fusion reactor concepts and a brief overview, the main irradiation-induced degradation challenges associated with RAFM/ODS steels are discussed. Their long-term degradation scenarios such as (a) low-temperature hardening embrittlement (LTHE)—including dose-temperature dependent yield stress, tensile elongations, necking ductility, test temperature effect on hardening, Charpy impact ductile-to-brittle transition temperature and fracture toughness, (b) intermediate temperature cavity swelling, (c) the effect of helium on LTHE and cavity swelling, (d) irradiation creep and (e) tritium management issues are reviewed. The potential causes of LTHE are discussed, which highlights the need for advanced characterisation techniques. The mechanical properties, including the tensile/Charpy impact of RAFM and ODS steels, are compared to show that the current generation of ODS steels also suffers from LTHE, and shows irradiation hardening up to high temperatures of ~400 °C–500 °C. To minimise this, future ODS steel development for FW/B-specific application should target materials with a lower Cr concentration (to minimise α'), and minimise other elements that could form embrittling phases under irradiation. RAFM steel-designing activities targeting improvements in creep and LTHE are reviewed. The need to better understand the synergistic effects of helium on the thermo-mechanical properties in the entire temperature range of FW/B is highlighted. Because fusion operating conditions will be complex, including stresses due to the magnetic field, primary loads like coolant pressure, secondary loads from thermal gradients, and due to spatial variation in damage levels and gas production rates, an experimentally validated multiscale modelling approach is suggested as a pathway to future reactor component designing such as for the fusion neutron science facility.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Scaling behavior of order parameters for the hybrid improper ferroelectric (Ca, Sr) 3 Ti 2 O 7
Here, we show that in contrast to the conventional view of a mean-field Landau-type behavior, the oxygen octahedral tilt ($\textit{R}$) and polarization (P) in the $A_3B_2\text{O}_7$ Ruddlesden-Popper hybrid improper ferroelectric (Ca,Sr) 3 Ti 2 O 7 exhibits the scaling behavior of a 2D Ising class near the para-to-ferroelectric transition temperature ($T_c$). We also show that $\textit{P}$ exhibits an additional transition from a 2D Ising to a 3D mean-field critical behavior at a temperature $T_{\text{d}} < T_{\text{c}}$, which is driven by enhanced interlayer dipolar correlations due to an increase in the ferroelectrically active $\textit{B}$-site centered dipoles.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Nonmetallic impurities improve mechanical properties of vapor-deposited tungsten
Mechanical properties of vapor deposited tungsten are improved by selective incorporation of various nonmetallic impurities. Addition of trace quantities of carbon, nitrogen, or oxygen can significantly increase both low and high temperature yield strength without greatly affecting ductile-to-brittle transition temperature.
Chin, J.↗