Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TARGETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Conceptual Spacer Design for the ATR GEN I Target for Pu-238 Production in the Advanced Test Reactor at Idaho National Laboratory

The initial target design used for Pu-238 production at Idaho National Laboratory was designed by Oak Ridge National Laboratory to optimize the production of Pu-238 in the High Flux Isotope Reactor (HFIR) and are referred to as HFIR GEN II targets. To take advantage of the Advanced Test Reactor’s (ATR) taller active core region a redesign of the HFIR GEN II targets was needed. It was proposed to stack two HFIR GEN II targets nose to nose about the core center line; however, this resulted in excessive neutron and photon heating in the pellets located in the center. This peak heating was not desirable so three alternative designs were investigated for the ATR GEN I targets. The python-based code, MCNP to ORIGEN2 in Python (MOPY), was used to calculate the heating rates after 40 days of irradiation to capture the effects of each configuration. The purpose of this paper is to document the details of these conceptual design calculations and comparisons for the ATR GEN I targets.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2016

CFD Analysis and Design of Detailed Target Configurations for an Accelerator-Driven Subcritical System

High-fidelity analysis has been utilized in the design of beam target options for an accelerator driven subcritical system. Designs featuring stacks of plates with square cross section have been investigated for both tungsten and uranium target materials. The presented work includes the first thermal-hydraulic simulations of the full, detailed target geometry. The innovative target cooling manifold design features many regions with complex flow features, including 90 bends and merging jets, which necessitate three-dimensional fluid simulations. These were performed using the commercial computational fluid dynamics code STAR-CCM+. Conjugate heat transfer was modeled between the plates, cladding, manifold structure, and fluid. Steady-state simulations were performed but lacked good residual convergence. Unsteady simulations were then performed, which converged well and demonstrated that flow instability existed in the lower portion of the manifold. It was established that the flow instability had little effect on the peak plate temperatures, which were well below the melting point. The estimated plate surface temperatures and target region pressure were shown to provide sufficient margin to subcooled boiling for standard operating conditions. This demonstrated the safety of both potential target configurations during normal operation.

43 PARTICLE ACCELERATORS↗
DOE OSTI2015

Final Report on MEGAPIE Target Irradiation and Post-Irradiation Examination

Megawatt pilot experiment (MEGAPIE) was successfully performed in 2006. One of the important goals of MEGAPIE is to understand the behaviour of structural materials of the target components exposed to high fluxes of high-energy protons and spallation neutrons in flowing LBE (liquid lead-bismuth eutectic) environment by conducting post-irradiation examination (PIE). The PIE includes four major parts: non-destructive test, radiochemical analysis of production and distribution of radionuclides produced by spallation reaction in LBE, analysis of LBE corrosion effects on structural materials, T91 and SS 316L steels, and mechanical testing of the T91 and SS 316L steels irradiated in the lower part of the target. The non-destructive test (NDT) including visual inspection and ultrasonic measurement was performed in the proton beam window area of the T91 calotte of the LBE container, the most intensively irradiated part of the MEGAPIE target. The visual inspection showed no visible failure and the ultrasonic measurement demonstrated no detectable change in thickness in the beam window area. Gamma mapping was also performed in the proton beam window area of the AlMg 3 safety-container. The gamma mapping results were used to evaluate the accumulated proton fluence distribution profile, the input data for determining irradiation parameters. Radiochemical analysis of radionuclides produced by spallation reaction in LBE is to improve the understanding of the production and distribution of radionuclides in the target. The results demonstrate that the radionuclides of noble metals, 207 Bi, 194 Hg/Au are rather homogeneously distributed within the target, while radionuclides of electropositive elements are found to be deposited on the steel-LBE interface. The corrosion effect of LBE on the structural components under intensive irradiation was investigated by metallography. The results show that no evident corrosion damages. However, unexpected deep cracks were found in the EBW (electron beam weld) of the LBE container in the intensive irradiation zone of the target, which should be formed during irradiation. In the SS 316L steel of the flow guide tube, inclusions or precipitates enriched with O, Si, S, Ca, Ti and Mn were observed. Many of them are very long, up to a few mm, and located on grain boundaries along the extrusion direction of the tube. The degradation of the mechanical properties of the T91 and SS 316L steels has been investigated by conducting tensile tests on the specimens extracted from the T91 and SS 316L components in the intensive irradiation region. The results obtained from the proton beam window of the T91 calotte exhibit a good ductility of T91 steel after irradiation at 6-7 dpa (displacement per atom) in contact with flowing LBE.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Facility target insert shielding assessment

Main objective of this report is to assess the basic shielding requirements for the vertical target insert and retrieval port. We used the baseline design for the vertical target insert in our calculations. The insert sits in the 12”-diameter cylindrical shaft extending from the service alley in the top floor of the facility all the way down to the target location. The target retrieval mechanism is a long rod with the target assembly attached and running the entire length of the vertical shaft. The insert also houses the helium cooling supply and return lines each with 2” diameter. In the present study we focused on calculating the neutron and photon dose rate fields on top of the target insert/retrieval mechanism in the service alley. Additionally, we studied a few prototypical configurations of the shielding layers in the vertical insert as well as on the top.

Accelerator Design, Technology, and Operations↗
DOE OSTI2016

Initiated chemical vapor deposited nanoadhesive for bonding National Ignition Facility's targets

Currently, the target fabrication scientists in National Ignition Facility Directorate at Lawrence Livermore National Laboratory (LLNL) is studying the propagation force resulted from laser impulses impacting a target. To best study this, they would like the adhesive used to glue the target substrates to be as thin as possible. The main objective of this research project is to create adhesive glue bonds for NIF’s targets that are ≤ 1 μm thick. Polyglycidylmethacrylate (PGMA) thin films were coated on various substrates using initiated chemical vapor deposition (iCVD). Film quality studies using white light interferometry reveal that the iCVD PGMA films were smooth. The coated substrates were bonded at 150 °C under vacuum, with low inflow of Nitrogen. Success in bonding most of NIF’s mock targets at thicknesses ≤ 1 μm indicates that our process is feasible in bonding the real targets. Key parameters that are required for successful bonding were concluded from the bonding results. They include inert bonding atmosphere, sufficient contact between the PGMA films, and smooth substrates. Average bond strength of 0.60 MPa was obtained from mechanical shearing tests. The bonding failure mode of the sheared interfaces was observed to be cohesive. Future work on this project will include reattempt to bond silica aerogel to iCVD PGMA coated substrates, stabilize carbon nanotube forests with iCVD PGMA coating, and kinetics study of PGMA thermal crosslinking.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Measurement of Single Spin Asymmetry in 3 He↑(e, e'K ± )X from a Transversely Polarized 3 He Target

Spin-dependent observables are a powerful tool to probe the internal structure of the nucleon and to study the dynamics of the strong interaction. Experimental study of the nucleon spin structure has provided us with many exciting and often surprising results. The so-called "spin crisis" in the 1980s revealed the limitation of naive quark-parton models and led to a worldwide effort to study the nucleon spin structure. However, this effort has been focused mainly on the nucleon's longitudinal spin structure. Recently, when the pioneer work revealed the significant role that transverse spin plays in understanding the full structure of the nucleon and in understanding the dynamics of the strong interaction, the study of the transverse spin structure became the new focus of the worldwide effort. Jefferson Lab (JLab) is located at Newport News, VA, US. It is equipped with the continuous electron beam accelerator facility (CEBAF) and four experimental halls: A, B, C and D. The accelerator can provide a continuous electron beam (2 ns beam bunch) with high polarization (up to ~ 90%) and high current (up to ~ 200μA) for fixed target experiments in all experimental halls. Hall A consists of two standard high-resolution spectrometers (HRS): left HRS (LHRS) and right HRS (RHRS). Another spectrometer, the BigBite spectrometer, can be installed on request by certain experiments. The experiment E06-010 ("Transversity Experiment") at JLab Hall A is the first measurement of the transverse spin structure of the neutron using a transversely polarized 3 He target and a 5.89 GeV incident electron beam. The experiment measured target single spin asymmetries (SSA) and beam-target double-pin asymmetries (DSA) in semi-inclusive deep-inelastic scattering (SIDIS) and in deep-inelastic scattering (DIS) processes. It also collected inclusive hadron (pion, kaon and proton) production data parasitically. The scattered electrons were detected in the BigBite spectrometer with associated detectors while the hadrons were detected with the LHRS which had excellent particle identification capabilities. In this dissertation, the first measurement of target single spin asymmetries of charged kaons produced in semi-inclusive deep inelastic scattering of electrons off a transversely polarized 3 He target will be discussed. Both the Collins and Sivers moments, which are related to the nucleon transversity and Sivers distributions, respectively, are extracted over the kinematical range of 0.1 bj <0.4 for K + and K - production. While the Collins and Sivers moments for K+ are consistent with zero within the experimental uncertainties, both moments for K- favor negative values. The Sivers moments are compared to the theoretical prediction from a phenomenological fit to the world data. While the K + Sivers moments are consistent with the prediction, the K - results differ from the prediction at the 2-sigma level. The measurements of SSA and DSA in the inclusive hadron (pion, kaon, proton) production channels, with an average transverse momentum T >=0.64 GeV/c, will also be discussed. The asymmetries strongly depend on the flavor of hadron. The π + and π - asymmetries are opposite in sign, demonstrated a strong flavor dependency similar to what has been observed in polarized p ↑ +p collisions. These measurements have provided important inputs to the world's data set on the investigation of transverse spin structure of the nucleon. They also laid the foundation for the future high precision study of the subject in the 12-GeV JLab and a future electron-ion collider.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2018

Residual Stress Measurements of Front Window Welds in a Prototypical Spallation Neutron Source Target Module

Spallation Neutron Source (SNS) target modules are fabricated from 316L stainless steel by welding together sections of machined components using electron beam welding. The failure of the tenth operational SNS target (Target 10) at an electron beam weld prompted an investigation into the residual stress remaining in the weld joint after joining to determine if welding procedures for SNS target fabrication produce detrimental residual stresses in or near the welds. Due to an issue with fabrication, the front section of an SNS target was removed from fabrication and made available for residual stress measurements. The residual stresses in an electron beam weld joining the front window and front body of the target prototype was measured at several locations near EBW2 weld between outer window and front body using the VUCLAN instrument. Different stress free d hkl 0 methods were used to calculated the residual strain and residual stress. Furthermore, the results show tensile residual stress up to 350MPa along the weld direction which peaked at weld location.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Northstar Mo100 Target Beam Spot Size Sensitivity Study

Northstar Mo100 target for production of the medical isotope Mo99 is particularly sensitive to beam over focusing because of the intended high power density. At 38 MeV and 6.32 mA (240 kW beam power, nominally 160 kW th in the target), small deviation from the nominal 12 mm FWHM beam can significantly increase the target disk temperatures and more importantly the load bearing target window temperature. A rhodotron will be the source of the electron beam to be used in the isotope production. This machine operates in a pulsed beam mode, currently expected to be at 50 Hz, which results in a 100 C temperature oscillation above and below the steady state temperature that is the focus of this study. This must be considered in the determination of minimum beam spot size that can be accepted by the target without risk of failure. In addition to the nominal beam spot size of 12 mm, the analysis of 10, 11 and 14.5 mm beam spot sizes are analyzed. The primary conclusion is that an over focused beam to just 11 mm FWHM is the minimum beam spot allowable, based on window temperature and the Ultimate Tensile Stress (UTS) of the window material Inconel 718 as a function of temperature. In contrast an under focused beam of 14.5 mm FWHM has much reduced target and window temperatures, but there is a resulting 6% drop in isotope production, all other factor staying the same. These results are presented herein.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2021

Post Examination of Candidate NpO 2 Targets for 238 Pu Production

Four targets composed of sintered NpO 2 pellets enclosed in Zircaloy cladding were irradiated in the High Flux Isotope Reactor for 2 to 4 cycles to determine if an oxide pellet and Zircaloy cladding would be usable candidates for 238 Pu production. The pellets were sintered to a high fraction of theoretical density (TD) and melt wires were placed in small holes that had been drilled in the center of selected pellets to determine if the pellet centers exceeded desirable operating temperatures. After irradiation, the targets were punctured to determine the internal target pressure and the fission gas release. None of the targets had excessive pressure, and fission gas release was in the range of 4 to 38%. The targets were then cut into segments for radiochemical analysis, and metallography (MET) mounts were created to examine the pellet microstructure and to search for the melt wires to determine if they had melted. Three of the four targets resulted in successful MET mounts; the two-cycle pellets were too friable to be handled. No signs of pellet melting were noted, and unfortunately, none of the melt wires could be recovered. The results indicate that this pellet/clad design offers a practical option for 238 Pu production.

36 MATERIALS SCIENCE↗
DOE OSTI2021

R&D toward design for a pion-production target for Mu2e-II

The Mu2e experiment at Fermilab will search for evidence of charged lepton flavor violation by observing the conversion of a negative muon into an electron in the Coulomb field of a nucleus without emission of neutrinos and will probe effective new-physics mass scales in the 103-104 TeV range. One of the main parts of the Mu2e experimental setup is its target station in which negative pions are generated in interactions of the 8 GeV primary proton beam with a tungsten target, which will be capable of producing $2\times10^{17}$ negative muons per year. Mu2e can be extended by a next generation experiment, Mu2e-II, with a sensitivity improved by another factor of 10 or more as enabled by the PIP-II accelerator upgrade project. PIP-II is a 250-meter-long linac capable of accelerating a 2 mA proton beam to a kinetic energy of 800 MeV corresponding to 1.6 MW of power. To achieve another factor of ten improvement in sensitivity, Mu2e-II will require about 100 kW of proton beam on target, and the added power requires a new target design. We will present our progress in RD of a target station conceptual design for Mu2e-II, using the MARS15 and G4beamline Monte-Carlo codes toward a selection between granular, conveyor, and rotating cylindrical target options.

Lynch, Kevin Richard↗
DOE OSTI2016

A New Solid Polarized Target for CLAS12 in Hall B

With Jefferson Lab's upgrade to a 12 GeV electron beam comes a new, improved detector system in Hall B: CLAS12. The dynamically polarized solid target, which was a mainstay of double-polarized scattering experiments in the 6 GeV era, must also be replaced, accommodating the constraints of the new Hall B layout. The new target and its horizontal refrigerator will fit in a space restricted by the new CLAS12 5T solenoid and detector package, making the center of the target sit within a narrow clearance that tapers from 30 to 10 cm in diameter over a length of 2.3 m. The target will dynamically polarize NH3 and/or ND3 in two target cells at 5T and 1K using 140 GHz microwaves, and will provide protons and deuterons polarized to above 90% and 40%, respectively. We present the proposed design of the new polarized target system for Hall B, and discuss the progress and challenges of the project.

Maxwell, James↗
DOE OSTI2023

Simulating target tests at AP0 facility for Mu2e

The predicted production of muons and energy deposition for the production target of the Mu2e experiment are dependent on the documentation of cross-sections values, the properties of the target’s material, etc. Hence, making real tests on similar targets before its use on Mu2e will be a good indicator of the accuracy of the simulations done for the experiment. The main goal of the project is to simulate a target test at the AP0 Target Facility, previously used to create the muon beam for the Muon g-2 experiment. Results from these simulations will be used as input to engineering models of the target to produce predicted stress and surface temperature distributions, parameters that will later be measured in future beam runs to validate underlying cross section models.

Delgado, Amii Matamoros↗
DOE OSTI2023

Secondary Pion Production using the LINAC Beam on Graphite and Tungsten Targets

The Fermilab 400-MeV Linac primary proton beam can produce precision, single-species secondary beams using a production target in the MeV Test Area experimental hall; specifically, pions from 4 up to 120 MeV kinetic energy. (These low energy pions rapidly decay into a muon beam in a secondary collection and transport beamline.) Although graphite is a standard production target material given its ultra-high temperature tolerance and low impact on the post-target primary beam, secondary pion/muon total production cross sections increase approximately as Z1/3 for positive muons and N2/3 for negative muons. Higher mass targets such as tungsten can potentially increase low-energy m+ and m- rates by factors of 3 and 8, respectively. Initial production studies have confirmed higher muon yield from heavy targets (tungsten vs carbon), but also, surprisingly, show significant differences in pion production between modern hadronic models (GENIEhad) and between GEANT and MCNP, state of the art production modeling codes. This project will further investigate the production discrepancies between these two target materials and between different physics models with high-statistics runs using the GEANT-based code, G4Beamline to better quantify the results and compare with production data which will be obtained using the MTA secondary beamline.

Ahmed, Shiza↗
DOE OSTI2024

Nuclear imaging to diagnose and correct target-driver registration at high-repetition-rate for improved reactor efficiency

Inertial Confinement Fusion produces energy from a burning plasma lasting a fraction of a nanosecond. Power plant designs based on Inertial Fusion Energy (IFE) will need to ignite targets 1-10 times a second, fired as projectiles into a chamber and delivering the driver to the target location. Driver asymmetry is known to impact ICF experiments at gain near unity and remains a candidate for primary yield degradation, and therefore fusion power plant energy output, for high-gain target designs. For a Fusion Power Plant (FPP), continuous and real-time monitoring of target performance provides an opportunity to stabilize or correct the target-driver registration. This requires x-ray and neutron imaging with a large field-of-view, sufficiently high resolution, fast analysis and to subtend a minimal solid angle. We introduce design criteria for such an imaging system that uses a coded aperture and time-gated, lens-coupled scintillators as a viable solution and outline the research steps required to field such a system. Integrating the imaging system into an IFE power plant as part of an active feedback loop could increase average power output by reducing the failure rate due to mis-aligned drivers with respect to the target.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Three-dimensional simulations of magneto-inertial Magnetic-Direct-Drive targets

For the cylindrically symmetric targets that are normally fielded on the Z machine, two dimensional axisymmetric MHD simulations provide the backbone of our target design capability. These simulations capture the essential operation of the target and allow for a wide range of physics to be addressed at a substantially lower computational cost than 3D simulations. This approach, however, makes some approximations that may impact its ability to accurately provide insight into target operation. As an example, in 2D simulations, targets are able to stagnate directly to the axis in a way that is not entirely physical, leading to uncertainty in the impact of the dynamical instabilities that are an important source of degradation for ICF concepts. In this report, we have performed a series of 3D calculations in order to assess the importance of this higher fidelity treatment on MagLIF target performance.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Multiphysics Simulations of Nanofibrous High Power Targets for the Inference of Failure Modes

Fermilab s High Power Targetry Research and Development (HPT R&D) group have been developing and studying an electrospun nanofiber target concept to support the need for robust targets in future fixed target facilities. These nanofiber mats have demonstrated resistance to radiation damage, and the free motion of the individual fibers is expected to mitigate the cyclic stresses induced by a pulsed, high-power beam. To evaluate the efficacy of this concept, nanofiber mat samples have been sent by the HPT R&D group to the HiRadMat facility at CERN for prototypic thermal shock testing; the outcomes of these experiments show that the survivability of a nanofiber target depends on its construction parameters, in particular the packing density of the fibers. Samples with higher packing densities have consistently been destroyed by exposure to the HiRadMat beam, with a hole at the beam center visible, and layers of nanofibers peeled away from the center hole, whereas samples with lower densities have survived with limited damage. The exact reason for the failure of the higher density targets was unclear at the time of the original experiments, but the results of our recent multiphysics simulations which recreate the experiments support the hypothesis that the expansion and pressurization of the air inside the target after being heated by the pulsed beam is the cause; in a high density nanofiber mat, the motion of air through the pores of the mat is much more restricted, and induces a larger pressure on the fibers, blowing the mat apart. In this talk, we ll share the results of these simulations and discuss how they support this hypothesis.

Asztalos, Will↗
DOE OSTI2024

Fabrication of a Point-Like Transmission Target for Reducing Computed Tomography Imaging Artifacts

In this study, we address the challenge of enhancing image quality and spatial resolution in computed tomography (CT) imaging by introducing simulation and fabrication of high aspect ratio, point-like transmission targets. Utilizing advanced electroplating techniques, traditionally employed in the fabrication of Through Substrate Via (TSV) interconnects for CMOS circuitry, we successfully embed copper targets within silicon substrates. This method allows us to create high-aspect-ratio features specifically designed for X-ray transmission targets, resulting in micro targets that exhibit a volume increase compared to conventional evaporated surface targets. Furthermore, we present simulation results of the X-ray spectrum generated by these targets, demonstrating their potential to significantly improve both image quality and spatial resolution in CT applications. Our findings suggest that leveraging advanced fabrication techniques can open new avenues for the development of enhanced imaging technologies in medical diagnostics and beyond.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Methodology to Establish Performance Targets for Building Energy Codes

This report explains the underlying development of the U.S. NZE building sector performance targets reported in Federal Register Notice XX. This document also includes NZE performance targets for U.S. states, which were developed following the same procedures used to develop the national values. These national and state targets are intended to support the establishment and attainment of NZE goals over time. Where residential and commercial building energy code compliance mechanisms apply to new buildings and major renovations and dictate performance requirements, these targets reflect the recommended, minimum levels of performance. Appendix A provides the performance values and targets by U.S. state for residential and commercial buildings. These include each state’s adopted energy code performance, current published MEC performance value, and a nominal NZE code compliance performance target. The current code and NZE values can be compared to the state adopted code value to indicate the level of advancement needed to move towards recommended NZE building performance levels. Additional supplemental resources are available to support states and local governments ready to move from setting NZE policy goals to adopting NZE codes. More information about these resources and the actions states can take to achieve NZE buildings with energy codes are provided in the body of this document.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗