Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Spray coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Anti-reflection coating with mullite and Duroid for large-diameter cryogenic sapphire and alumina optics

We developed a broadband two-layer anti-reflection (AR) coating for use on a sapphire half-wave plate (HWP) and an alumina infrared (IR) filter for the cosmic microwave background (CMB) polarimetry. Measuring the faint CMB B-mode signals requires maximizing the number of photons reaching the detectors and minimizing spurious polarization due to reflection with an off-axis incident angle. Sapphire and alumina have high refractive indices of 3.1 and are highly reflective without an AR coating. This paper presents the design, fabrication, quality control, and measured performance of an AR coating using thermally sprayed mullite and Duroid 5880LZ. This technology enables large optical elements with diameters of 600 mm. We also present a thermography-based nondestructive quality control technique, which is key to assuring good adhesion and preventing delamination when thermal cycling. We demonstrate the average reflectance of about 2.6% (0.9%) for two observing bands centered at 90/150 (220/280) GHz. At room temperature, the average transmittance of a 105 mm square test sample at 220/280 GHz is 83%, and it will increase to 90% at 100 K, attributed to reduced absorption losses. Therefore, our developed layering technique has proved effective for 220/280 GHz applications, particularly in addressing dielectric loss concerns. This AR coating technology has been deployed in the cryogenic HWP and IR filters of the Simons Array and the Simons observatory experiments and applies to future experiments such as CMB-S4.

Sakaguri, Kana (ORCID:0000000156678118)↗
DOE OSTI2020

3D Printing Prototypes for a Reflector-Based Broadband Axion Search

This work sought to begin research and development on a horn antenna which can be used to transfer the energy of microwave photons produced by axions in a strong magnetic field to a coaxial cable for measurement. 3D prototypes of pyramidal horn antennas and a parabolic reflector were printed and then coated with conductive spray paint. The S 11 parameter was measured and simulated for both 3D printed horn antenna and the conical horn antenna both with and without the reflector present to determine how much of the radiated power was reflected back. Ultimately, for both the conical and pyramidal antennas, less than one percent of the energy emitted by the antennas was reflected back. When the pyramidal antenna was tilted by about 45 degrees, however, around 30-40 percent of the microwaves emitted by the antennas was reflected back.

43 PARTICLE ACCELERATORS↗
NASA NTRS1979

Array Automated Assembly, Phase 2

The baseline process sequence using nontextured square wafers was integrated. Difficulties encountered include: (1) replacement of the N-250 spray on diffusion source with PX-10 source; and (2) modification of the firing for printed silver and aluminum contracts is required to accommodate the change of wafer size and shape. Results indicate that the cells processed through the entire process sequence except laser scribe and spray on AR coating indicate the process sequence is feasible. Greater cell conversion efficiency is presented.

Taylor, W. E.↗
NASA NTRS1979

Automated aray assembly, phase 2

A manufacturing process suitable for the large-scale production of silicon solar array modules at a cost of less than $500/peak kW is described. Factors which control the efficiency of ion implanted silicon solar cells, screen-printed thick film metallization, spray-on antireflection coating process, and panel assembly are discussed. Conclusions regarding technological readiness or cost effectiveness of individual process steps are presented.

Daiello, R. V.↗
NASA NTRS1979

Automated Array Assembly, Phase 2

The large scale production of silicon solar cell array panels is discussed. The cost and performance of three manufacturing sequences designed to convert silicon sheet and wafers into solar panels is analyzed. The production of ion implanted and furnace annealed solar cells made using solar grade n- and p-type wafers is examined. The performance of production size lots is examined with regard to the relationship between the ion implant and furnace anneal parameters and the ability to form consistently good thick film screen printed contacts. The spray on antireflection coating process is evaluated. The performance of several lots of cells before and after coating is measured. The structure and refractive index of the RCA I (TiO2) coating is compared with commercial solutions. Sensitivity of coated, screen printed cells to the post heat treatment required to cure the films is assessed.

Daiello, R. V.↗
NASA NTRS1978

Static evaluation of surface coatings for compliant gas bearings in an oxidizing atmosphere to 650 C

Hard wear-resistant coatings and soft low shear strength coatings were developed for an air-lubricated compliant journal bearing for a future automotive gas turbine engine. The coatings were expected to function in either 540 or 650 C ambient. Soft lubricant coatings were generally limited in temperature. Therefore emphasis was on the hard wear-resistant coatings. The coating materials covered were TiC, B4C, Cr3C2, WC, SiC, CrB2, TiB2, Cr2O3, Al2O3, Si3N4, Tribaloy 800, CaF2, CaF2-BaF2 eutectic, Ni-Co, silver, CdO-graphite and proprietary compounds. The coatings on test coupons were subjected to static oven screening tests. The test consisted of exposure of material samples in an oven for 300 h at the maximum temperature (540 or 650 C) and ten temperature cycles from room temperature to the maximum service temperature. On the basis of the specimen examinations the following coatings were recommended for future wear tests: TiC (sputtered), Cr2O3 (sputtered), Si3N4 (sputtered), CdO and graphite (fused), Kaman DES (a proprietary coating), CrB2 (plasma sprayed), Cr3C2 (detonation gun) and NASA PS-106 (plasma sprayed).

Bhushan, B.↗
NASA NTRS1980

High temperature self-lubricating coatings for air lubricated foil bearings for the automotive gas turbine engine

coating combinations were developed for compliant surface bearings and journals to be used in an automotive gas turbine engine. The coatings were able to withstand the sliding start/stops during rotor liftoff and touchdown and occasional short time, high speed rubs under representative loading of the engine. Some dozen coating variations of CdO-graphite, Cr2O3 (by sputtering) and CaF2 (plasma sprayed) were identified. The coatings were optimized and they were examined for stoichiometry, metallurgical condition, and adhesion. Sputtered Cr2O3 was most adherent when optimum parameters were used and it was applied on an annealed (soft) substrate. Metallic binders and interlayers were used to improve the ductility and the adherence.

Bhushan, B.↗
NASA NTRS1981

A Module Experimental Process System Development Unit (MEPSDU)

The technical readiness of a cost effective process sequence that has the potential for the production of flat plate photovoltaic modules which met the price goal in 1986 of $.70 or less per Watt peak was demonstrated. The proposed process sequence was reviewed and laboratory verification experiments were conducted. The preliminary process includes the following features: semicrystalline silicon (10 cm by 10 cm) as the silicon input material; spray on dopant diffusion source; Al paste BSF formation; spray on AR coating; electroless Ni plate solder dip metallization; laser scribe edges; K & S tabbing and stringing machine; and laminated EVA modules.

Source record↗
NASA NTRS1992

Director's discretionary fund report for FY 1991

The Director's Discretionary Fund (DDF) at the Ames Research Center was established to fund innovative, high-risk projects in basic research which would otherwise be difficult to initiate, but which are essential to our future programs. Here, summaries are given of individual projects within this program. Topics covered include scheduling electric power for the Ames Research Center, the feasibility of light emitting diode arrays as a lighting source for plant growth chambers in space, plasma spraying of nonoxide coatings using a constricted arcjet, and the characterization of vortex impingement footprint using non-intrusive measurement techniques.

Source record↗
NASA NTRS1990

Thermal response of various thermal barrier coatings in a high heat flux rocket engine

Traditional APS ZrO2-Y2O3 thermal barrier coatings (TBCs) formed by air plasma spraying and low pressure and air plasma sprayed ZrO2-Y2O3/NiCrAlY cermet coatings were tested in an H2-O2 rocket engine. The test cycle was approximately 1.2 s at 1400 C in a hydrogen-rich environment. During testing, the maximum metal temperature without a coating was 1310 C. The traditional ZrO2-Y2O3 TBCs with a 100-125 micron thick ceramic layer reduced the maximum metal temperature by approximately 350 C. Increasing the ceramic layer thickness to 200-225 microns resulted in an additional metal temperature reduction of 100 C. However, the cermet coatings, consisting of a ceramic and metal mixture, exhibited a much lower thermal protection capability by reducing the maximum metal temperature by approximately 100 C. It was also found that the surface roughness of the traditional TBCs had little effect on the thermal response.

Nesbitt, J. A.↗
NASA NTRS1995

Langley Research Center - Soluble Imide (LaRC-SI)

This report is about experimenting and developing uses for the new thermal plastic developed by Dr. Robert Bryant called the 'Langley Research Center - Soluble Imide' (LaRC-SI). The three developments are: the use of the LaRC-SI as a dielectric for thin film sensors, as an adhesive to place diamonds on surfaces to increase thermal conductivity, and as an intermediate layer to allow the placement of metal on aluminum nitride. The LaRC-SI was developed by Dr. Robert G. Bryant, a chemical engineer at NASA Langley Research Center. The unique properties of this material is that it is an amorphous thermoplastic. This means that it can be reformed at elevated temperature and pressures. It can be applied in the form of a spray, spin, dip coating, paint, or spread with a doctors blade. The LaRC-SI has excellent adhesive and dielectric properties. It can also be recycled. Potential applications for this material are resin for mechanical parts such as gears, bearings and valves, advanced composites like carbon fiber, high strength adhesives, thin film circuits, and as a dielectric film for placing electrical components on conductive materials.

Stang, David↗
DOE OSTI2024

Multi-coat polymer photonic crystal films

Polymer composite photonic crystal materials are disclosed as coatings and topcoats which have high reflection (>30%) in a specific range of the electromagnetic spectrum, such as ultraviolet (<400 nm), visible (Vis, 400 nm-700 nm), or near-infrared radiation range (NIR, 700-2000 nm), and relatively low reflection (<20% reflection) in a second, different range of the electromagnetic spectrum. Surprisingly, it was found that through a formulation and additives approach, the optical properties of polymer composite photonic crystal films can be selectively modified from a variety of different coating methods, including spray deposition.

Pearson, Ryan Michael↗
NASA NTRS2001

Thermal Processing Effects on the Adhesive Strength of PS304 High Temperature Solid Lubricant Coatings

In this paper the effects of post deposition heat treatments on the cohesive and adhesive strength properties of PS304, a plasma sprayed nickel-chrome based, high temperature solid lubricant coating deposited on stainless steel, are studied. Plasma spray deposited coating samples were exposed in air at temperatures from 432 to 650 C for up to 500 hr to promote residual stress relief, enhance particle to particle bonding and increase coating to substrate bond strength. Coating pull-off strength was measured using a commercial adhesion tester that utilizes 13 mm diameter aluminum pull studs attached to the coating surface with epoxy. Pull off force was automatically recorded and converted to coating pull off strength. As deposited coating samples were also tested as a baseline. The as-deposited (untreated) samples either delaminated at the coating-substrate interface or failed internally (cohesive failure) at about 17 MPa. Samples heat treated at temperatures above 540 C for 100 hr or at 600 C or above for more than 24 hr exhibited strengths above 31 MPa, nearly a two fold increase. Coating failure occurred inside the body of the coating (cohesive failure) for nearly all of the heat-treated samples and only occasionally at the coating substrate interface (adhesive failure). Metallographic analyses of heat-treated coatings indicate that the Nickel-Chromium binder in the PS304 appears to have segregated into two phases, a high nickel matrix phase and a high chromium precipitated phase. Analysis of the precipitates indicates the presence of silicon, a constituent of a flow enhancing additive in the commercial NiCr powder. The exact nature and structure of the precipitate phase is not known. This microstructural change is believed to be partially responsible for the coating strength increase. Diffusion bonding between particles may also be playing a role. Increasing the heat treatment temperature, exposure time or both accelerate the heat treatment process. Preliminary measurements indicate that the heat treatment also results in a one time, permanent coating thickness increase of about 3%. Based upon these results, the incorporation of a heat treatment prior to final finishing has been incorporated in the application process of this coating technology.

DellaCorte, Christopher↗
DOE OSTI2023

Aerosol Manufacturing Technology to Produce Low-Cobalt Li-ion Battery Cathodes

Although considerable progress has been made with battery materials over the last 10 years, the cathode remains a major performance-limiting material in Li-ion battery (LIB) technology. New materials and battery chemistries will overcome some of the remaining challenges, but cathode materials must also be manufactured at a lower cost and with a smaller environmental footprint using new processes that can also enable improved control over stoichiometry, morphology, and compositional homogeneity. Cabot, Argonne National Laboratory and SAFT research teams are combining their extensive expertise in particle synthesis, battery materials and cell design to develop a low-cost, flexible aerosol manufacturing technology for production of high-performance cathode active materials (CAM). This project will develop low-Co CAMs via Reactive Spray Technology (RST) and Flame Spray Pyrolysis (FSP) to reach performance targets of < 50 mg Cobalt/Wh.

25 ENERGY STORAGE↗
NASA NTRS2019

SOFI Coating Study

Results are presented for the reflectivity of spray on foam insulation (SOFI) samples coated with a new high solar reflectivity coating. Reflectance spectra are presented comparing bare SOFI to samples with one, two, or three layers of the new coating as well as one sample with white paint. Samples were coated on the front side of the SOFI, where the surface height varies significantly, as well as on the flatter back surface. Predicted solar absorbance values are provided for a few select cases.

Youngquist, R.↗
NASA NTRS1995

Thermal spray processing

Thermal spray processing has been used for a number of years to cost-effecticely apply TBC's for a wide range of heat engine applications. In particular, bond coats are applied by plasma spray and HVOF techniques and partially-stabilized zirconia top coats are applied by plasma spray methods. Thermal spray involves melting and rapid transport of the molten particles to the substrate, where high-rate solidification and coating build-up occur. It is the very nature of this melt processing that leads to the unique layered microstructure, as well as the apparent imperfections, so readily identified with thermal spray. Modeling the process, process-induced residual stresses, and thermal conductivity will be discussed in light of a new understanding of porosity and its anisotropy. Microcracking can be understood using new approaches, allowing a fuller view of the processing-performance connection. Detailed electron microscopic, novel neutron diffraction and fracture analysis of the deposits can lead to a better understanding of how overall microstructure can be controlled to influence critical properties of the deposited TBC system.

Herman, H.↗