Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Slow control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Method for automatic correction of offset drift in online sensors

Abstract Successful operation and optimization of water treatment systems hinge on the availability of high-quality online sensor measurements. Ideally, the available measurements should be simultaneously accurate (i.e., unbiased and precise), representative, voluminous, and timely. This remains a pain-point in current water infrastructures, forming a barrier to a wider adoption of advanced and autonomous control systems. While short-lived symptoms, such as outliers and spikes, can be detected or corrected with state-of-the-art tools for fault detection and identification, it is much more difficult to detect, diagnose, and correct the symptoms of slow faults, such as changes in offset or sensitivity due to drift. The time scale of drift is often longer than the time scales of the system dynamics of interest. Moreover, sensor drift has been shown to occur at the same time and with similar rates when sensors are exposed to the same conditions. This challenges data quality management strategies based on redundancy. In this contribution, we develop a new method, including both a hands-off sensor calibration mechanism and an information-seeking control architecture that can handle the unique challenge of simultaneous and similar drift in online sensors.

Chowdhury, Dhrubajit↗
NASA NTRS2006

Optimum Design of a Compound Helicopter

A design and aeromechanics investigation was conducted for a 100,000-lb compound helicopter with a single main rotor, which is to cruise at 250 knots at 4000 ft/95 deg F condition. Performance, stability, and control analyses were conducted with the comprehensive rotorcraft analysis CAMRAD II. Wind tunnel test measurements of the performance of the H-34 and UH-1D rotors at high advance ratio were compared with calculations to assess the accuracy of the analysis for the design of a high speed helicopter. In general, good correlation was obtained when an increase of drag coefficients in the reverse flow region was implemented. An assessment of various design parameters (disk loading, blade loading, wing loading) on the performance of the compound helicopter was conducted. Lower wing loading (larger wing area) and higher blade loading (smaller blade chord) increased aircraft lift-to-drag ratio. However, disk loading has a small influence on aircraft lift-to-drag ratio. A rotor parametric study showed that most of the benefit of slowing the rotor occurred at the initial 20 to 30% reduction of the advancing blade tip Mach number. No stability issues were observed with the current design. Control derivatives did not change significantly with speed, but the did exhibit significant coupling.

Yeo, Hyeonsoo↗
DOE OSTI2025

Solvation directed morphological control in metal oxide nanostructures

The development of structural hierarchy on various length scales during the crystallization process is ubiquitous in biological systems and minerals and is common in synthetic nanomaterials. The driving forces for the formation of complex architectures range from local interfacial interactions, that modify interfacial speciation, local supersaturation, and nucleation barriers, to macroscopic interparticle forces. Although it is enticing to interpret the formation of hierarchical architectures as the assembly of independently nucleated building blocks, crystallization pathways often follow monomer-by-monomer addition with structural complexity arising from interfacial chemical coupling and strongly correlated fluctuation dynamics in the electric double layers. Here, we show that the development of structural hierarchy through heterogeneous nucleation is driven by dipolar and solvation forces. Specifically, coupled simulations and experimental studies revealed that dipole build-up along the slow growth direction can trigger twinning and the development of branched architectures. Enthalpic solvation interactions were shown to either enhance or reduce the dipole moment of the nanoparticles and, thereby, control crystal morphology and architecture. The systematic studies of chemical coupling between different solvents and undercoordinated surface atoms of the growing nanocrystals revealed the mechanism of dimensionality control and the development of structural hierarchy without ligands or structure-directing agents.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Effects of polycarboxylate ether (PCE)-based superplasticizer on the dissolution and subsequent hydration of calcium oxide (CaO)

Calcium oxide (CaO) is an important construction material, used as expansive agent, alkaline activator, and repairing material for historical structures. In this study, the dissolution and subsequent hydration of CaO, with or without the polycarboxylate ether (PCE)-based superplasticizer, were investigated to elucidate the complex crystallization process of calcium hydroxide (Ca(OH){sub 2}). On contact with pure water, CaO particles began to hydrate within a few minutes, while releasing a significant amount of heat. Adding superplasticizer slowed such rapid heat evolution by forming a dormant period and significantly affected the crystallinity of the hydration product. The dormant period was controllable by the amount of added superplasticizer. Moreover, as a result of early nucleation of Ca(OH){sub 2}, the formation of 10–100-nm spherical nanoparticles was observed via an in-situ transmission electron microscope, which completely differed from the final crystal shape of the hydration product.

36 MATERIALS SCIENCE↗
DOE OSTI2022

First direct observations of gear-changing in a collider

In this work we perform the first demonstration of gear-changing in a real world collider. Gear-changing refers to a collision scheme where each ring of a collider stores a different harmonic number of bunches. These bunches are kept synchronized using different velocities. Such a system has been theorized, but has now been demonstrated using the Double ElectroStatic Ion Ring ExpEriment (DESIREE) in Stockholm Sweden. The experiment was able to demonstrate a gear-changing system, with both four on three bunches and five on four bunches. We determined a measurable parameter that shows a gear-changing system out to $37500$ turns of the slow beam (1 second). We were also able to detect a measurable longitudinal beam-beam interaction. We developed insights into how to control this type of system, opening up new possibilities, and showing that DESIREE can be used for gear-changing research.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Design of an 8-channel 40 GS/s 20 mW/Ch waveform sampling ASIC in 65 nm CMOS

One picosecond timing resolution is the entry point to signature based searches relying on secondary/tertiary vertices and particle identification. We describe PSEC5, an 8-channel 40 GS/s waveform-sampling ASIC in TSMC 65 nm process targetting one picosecond resolution at 20 mW power per channel. Each channel consists of four fast and one slow switched capacitor arrays (SCA), allowing for picosecond time resolution combined with a long effective buffer. Each fast SCA is 1.6 ns long and has a nominal sampling rate of 40 GS/s. The slow SCA is 204.8 ns long and samples at 5 GS/s. Recording of the analog data for each channel is triggered by a fast discriminator capable of multiple triggering during the window of the slow SCA. To achieve a large dynamic range, low leakage, and high bandwidth, the SCA sampling switches are implemented as 2.5 V nMOSFETs controlled by 1.2 V shift registers. Stored analog data are digitized by an external ADC at 10 bits or better. Specifications on operational parameters include a 4 GHz analog bandwidth and a dead time of 20 microseconds, corresponding to a 50 kHz readout rate, determined by the choice of the external ADC. PSEC5 has been submitted for fabrication.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Deciphering Charge Transfer Processes in Transition Metal Complexes from the Perspective of Ultrafast Electronic and Nuclear Motions

Chemical transformations in charge transfer states result from the interplay between electronic dynamics and nuclear reorganization along excited-state trajectories. Here, in this study, we investigate the ultrafast structural dynamics following photoinduced electron transfer from the metal-metal-to-ligand charge transfer state of an electron donor, a Pt dimer complex, to a covalently linked electron acceptor group using ultrafast time-resolved wide-angle X-ray scattering and optical transient absorption spectroscopy methods to disentangle the interdependence of the excited-state electronic and nuclear dynamics. Following photoexcitation, Pt-Pt bond formation and contraction takes up to 1 ps, much slower than the corresponding process in analogous complexes without electron acceptor groups. Because the Pt-Pt distance change is slow with respect to excited-state electron transfer, it can affect the rate of electron transfer. These results have potential impacts on controlling electron transfer rates via structural alterations to the electron donor group, tuning the charge transfer driving force.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Modification of Ni-20Cr corrosion dealloying behavior in molten fluorides via cold work induced plastic deformation

The corrosion dealloying behavior of cold-worked (CW) Ni20Cr alloy (wt%) was studied in molten LiF-NaF-KF (or FLiNaK) salts at 600 °C, equal to a homologous temperature (TH) of 0.52. Alloys were cold-rolled to achieve reductions of thickness of 10%, 30%, and 50% introducing plastic deformation and a high density of dislocations. Potentiostatic holds (Eapplied) were applied in two different electrode potential regimes. At 1.75VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, Cr dealloying to Cr(II) and Cr(III) is predominant, while at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, both Ni and Cr are oxidized in molten FLiNaK at 600 °C. In these potential regimes, dealloyed Ni20Cr displayed bicontinuous porosity within the grain interior and at grain boundaries, driven by the high driving force for Cr dissolution and sustained by defect mediated outward solid state diffusion of Cr in parallel with surface diffusion of Ni. The bicontinuous porous structure developed was observed to undergo further coarsening and densification of the Ni-rich ligaments at a higher electrode potential. The main effect of CW observed is the introduction of plastic deformation and dislocation substructures that serve as short-circuit paths for Cr solid state diffusion to surfaces exposed to FLiNaK. This modified the evolution of the bicontinuous porous structure which increased with CW substantially. Kinetic analysis reveals that the Cr dealloying at +1.75 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ and 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ is initially charge transfer controlled, except for the 50% CW condition at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, where the process becomes limited by slow Cr defect mediated bulk diffusion. The rate determining factors are explored and compared to experimental results.

Chan, Ho Lun↗
NASA NTRS1979

Shaft speed control

Simple mechanism controls rotation of heavy-duty shaft by mechanical comparison with rotation of small, precise, stepper motor. Mechanism can be used to limit winding and unwinding speeds of large spools and reels and to control speed of other rotating shafts. Setup incorporates reference shaft geared down from stepper motor and feedback shaft geared up from shaft to be controlled. Feedback and reference shafts are coupled with brake assembly inside stationary cylinder. When work shaft speeds up, brakes are activated automatically to slow it down.

Ford, A. G.↗
NASA NTRS1986

Pulling-Speed Control for Silicon-Web Growth

Proposed control system for dendritic-web growth of silicon ribbons varies ribbon speed according to melt temperature. System prevents too fast or too slow withdrawal of silicon web, which cause pullout of web or excessive web thickness, respectively. System also enables semiautomatic startup of web growth by automatically increasing web speed from zero to optimum value.

Richter, R.↗
NASA NTRS1994

Experiment K-7-18: Effects of Spaceflight in the Muscle Adductor Longus of Rats Flown in the Soviet Biosatellite Cosmos 2044: A Study Employing Neural Cell Adhesion Molecules (N-CAM) Immunocytochemistry and Conventional Morphological Techniques (Light and Electron Microscopy) - Part 1

The effects of spaceflight upon the 'slow' muscle adductor longus was examined in rats flown in the Soviet Biosatellite COSMOS 2044. Three groups - synchronous, vivarium and basal served as controls. The techniques employed included standard methods for light microscopy, N-CAM immunocytochemistry and electron microscopy. Light microscopic observations revealed myofiber atrophy, contraction bands and segmental necrosis accompanied by cellular infiltrates composed of macrophages, leucocytes and mononuclear cells. N-CAM immunoreactivity was seen (N-CAM-IR) on the myofiber surface, satellite cells and in regenerating myofibers reminiscent of myotubes. Ultrastructural alterations included Z band streaming, disorganization of myofibrillar architecture, sarcoplasmic degradation, extensive segmental necrosis with preservation of the basement membrane, degenerative phenomena of the capillary endothelium and cellular invasion of necrotic areas. Regenerating myofibers were identified by the presence of increased amounts of ribosomal aggregates and chains of polyribosomes associated with myofilaments that displayed varied distributive patterns. The principal electron microscopic changes of the neuromuscular junctions consisted of a decrease or absence of synaptic vesicles, degeneration of axon terminals, increased number of microtubules, vacant axonal spaces and axonal sprouting. The present observations indicate that major alterations such as myofibrillar disruption and necrosis, muscle regeneration and denervation and synaptic remodeling at the level of the neuromuscular junction may take place during spaceflight.

Daunton, N. G.↗
NASA NTRS1997

Sleep and morningness-eveningness in the 'middle' years of life (20-59 y)

The following four issues were assessed in a group of 110 adults between the age of 20 and 59y: (1) the effect of age (regarded as a continuous variable) on polysomnographic sleep characteristics, habitual sleep-diary patterns, and subjective sleep quality; (2) the effects of age on morningness-eveningness; (3) the effects of morningness-eveningness on sleep, after controlling for the effects of age; and (4) the role of morningness-eveningness as a mediator of the age and sleep relationship. Increasing age was related to earlier habitual waketime, earlier bedtime, less time in bed and better mood and alertness at waketime. In the laboratory, increasing age was associated with less time asleep, increased number of awakenings, decreased sleep efficiency, lower percentages of slow-wave sleep (SWS) and rapid eye movement (REM) sleep, higher percentages of Stage 1 and 2, shorter REM latency and reduced REM activity and density. Increasing age was also associated with higher morningness scores. After controlling for the effects of age, morningness was associated with earlier waketime, earlier bedtime, less time in bed, better alertness at waketime, less time spent asleep, more wake in the last 2 h of sleep, decreased REM activity, less stage REM (min and percentage), more Stage 1 (min and percentage) and fewer minutes of Stage 2. For one set of variables (night time in bed, waketime, total sleep time, wake in the last 2 h of sleep and minutes of REM and REM activity), morningness-eveningness accounted for about half of the relationship between age and sleep. For another set of variables (bedtime, alertness at waketime, percentages of REM and Stage 1), morningness-eveningness accounted for the entire relationship between age and sleep. In conclusion, age and morningness were both important predictors of the habitual sleep patterns and polysomnographic sleep characteristics of people in the middle years of life (20-59 y).

Non-NASA Center↗
DOE OSTI2020

Critical Role of Anion–Solvent Interactions for Dynamics of Solvent-in-Salt Solutions

Most polar solvent molecules are unstable toward electrode materials used in Li-based batteries. Solid electrolytes and ionic liquids are far more stable; however, they have relatively low conductivity, and therefore electrical energy storage devices based on them would suffer from low power. Solvent-in-salt (SIS) systems combine chemical stability with relatively high conductivity. Here, we show how the nature of the employed anion affects the structure and dynamics of SIS systems. The transport of ions in lithium bis(fluorosulfonyl)imide (Li-FSI) systems was determined to be always faster than that in lithium bis(trifluoromethanesulfonyl)imide (Li-TFSI) systems. Moreover, we found that viscosity does not solely control conductivity and that the lower conductivity of TFSI – solutions is related to their stronger interaction with the solvent. This restricts solvent dynamics and slows down ion motions compared to that of FSI – . Interestingly, the TFSI–solvent interaction also leads to better charge separation (weaker ion–ion correlations) and a higher transference number for Li. Finally, our results suggest that the ability to tune the solvent network formed around the anions may further improve electrolyte conductivity and Li transference number for safer and more efficient energy storage devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Leaching Kinetics of Rare Earth Elements from Fire Clay Seam Coal

Recovery of rare earth elements (REEs) from coal samples collected from the Fire Clay coal seam using diluted mineral acid solutions was investigated. The initial processing step was coal recovery using conventional froth flotation which concentrated the REEs in tailing material resulting in an upgrade to values around 700 ppm on a dry whole mass basis. Leaching experiments were performed on the flotation tailings material using a 1.2 M sulfuric acid solution adjusted to a temperature of 75 °C to study the extractability of REEs from coal material. The effect of particle size, leaching time, leaching temperature, and solid concentration on REE leaching recovery were evaluated. The kinetic data obtained from leaching over a range of temperatures suggested that the leaching process follows the shrinking core model with possibly a mixed control mechanism that may be a result of several heterogenous materials leaching simultaneously. Leaching recovery increased rapidly at the beginning of the reaction then slowed as the system reached equilibrium. The apparent activation energy determined from test data obtained over a range of temperatures using 1 M sulfuric acid was 36 kJ/mol for the first 20 min of reaction time and 27 kJ/mol for the leaching period between 20 and 120 min. The leaching of light REEs during the initial stage was determined to be driven by a chemical reaction, followed by the formation of a product layer, which required lower activation energy in the later stage of leaching. In regards to the heavy REEs, the major mechanism for leaching is desorption and the product layer formation does not affect the heavy REEs significantly.

58 GEOSCIENCES↗
NASA NTRS1974

Spacecraft control section for the improved Small Astronomy Satellite (SAS)

The upgraded spacecraft control section for the Small Astronomy Satellite is able to point its thrust axis to any direction in space; it can also spin or slow its outer body rotation to zero for star-locked pointing of side viewing experiments. A programmable telemetry system and delayed command system enhance the inherent capability of a spacecraft designed to be used for a variety of experiments, each of which can be built independently and attached just prior to final acceptance testing and launch. The design of this new spacecraft, whose first launch is scheduled for 1975, is provided in sufficient detail to permit the reader to ascertain its suitability for specific experiments. A summary of the spacecraft characteristics, project reliability requirements, and environmental test conditions are included in the appendices.

Townsend, M. R.↗
NASA NTRS1980

Plants and weightlessness

The growth of two plants, wall cress and short-day red goosefoot, was traced for their entire lifetime in weightlessness. In the beginning both plants grew normally: the seeds sprouted in the normal periods, and the shoots did not differ in any way from the control plants. It is true that certain roots lost their normal orientation and did not go deeper into the nutrient medium, but rather crept over its surface. But then both the wall cress and the goosefoot slowed down their normal rate of growth, which became noticeable from the rate of formation of new leaves in the wall cress and stem development in the goosefoot. Although no disorders were successfully found in the morphology of the two plants, almost half of the experimental cress and goosefoot plants ceased growth completely, yellowed and died. The other part continued to develop normally and by the end of vegetation, differed from the control plants only in a lower height. Not all were fertile since certain experimental plants, after losing spatial orientation, became twisted and produced sterile flowers.

Karminskiy, V.↗
NASA NTRS1980

A study of stall deterrent systems for general aviation aircraft

Stall deterrent concepts for general aviation aircraft have been investigated using simulation studies and flight test experiments. It was found that the simulator was suitable for the development of deterrent system concepts, but the simulator was unacceptable for pilot evaluation of system effectiveness under typical stall/spin accident conditions. A Cessna 319 was outfitted with sensors, servoactuators, and analog control logic necessary to investigate a wide range of stall deterrent systems. It was found that an acoustic stall sensor and an error control law were sufficient for stall deterrence. The pitch intervention control system prevented aircraft stall for all aircraft configurations and pilot inputs. The variable up elevator stop concept was found to be effective for slow decelerations to aircraft stall. The stall deterrent systems were evaluated by four professional pilots and three low time pilots.

Bennett, A. G.↗
NASA NTRS1985

Recovery in skeletal muscle contractile function after prolonged hindlimb immobilization

The effect of three-month hindlimb immobilization (IM) in rats on contractile properties of slow-twitch soleus (SOL), fast-twitch extensor digitorum longus, and fast-twitch superficial region of the vastus lateralis were measured after 0, 14, 28, 60, and 90 days of recovery on excized, horizontally suspended muscles stimulated electrically to maximal twitch tension. IM caused decreases in muscle-to-body weight ratios for all muscles, with no complete recovery even after 90 days. The contractile properties of the fast-twitch muscles were less affected by IM than those of the slow-twitch SOL. The SOL isometric twitch duration was shortened, due to reduced contraction and half-relaxation time, both of which returned to control levels after 14 days of recovery. The peak tetanic tension, P(O), g/sq cm,, decreased with IM by 46 percent in the SOL, but recovered by the 28th day. The maximum shortening velocity was not altered by IM in any of the muscles. Thus, normal contractile function could recover after prolonged limb IM.

Fitts, R. H.↗