Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Simplified Simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Neutron backscatter edges as a diagnostic of burn propagation

High gain in hotspot-ignition inertial confinement fusion (ICF) implosions requires the propagation of thermonuclear burn from a central hotspot to the surrounding cold dense fuel. As ICF experiments enter the burning plasma regime, diagnostic signatures of burn propagation must be identified. In previous work [A. J. Crilly et al., Phys. Plasmas 27(1), 012701 (2020)], it has been shown that the spectral shape of the neutron backscatter edges is sensitive to the dense fuel hydrodynamic conditions. The backscatter edges are prominent features in the ICF neutron spectrum produced by the 180° scattering of primary deuterium–tritium fusion neutrons from ions. In this work, synthetic neutron spectra from radiation-hydrodynamics simulations of burning ICF implosions are used to assess the backscatter edge analysis in a propagating burn regime. Significant changes to the edge's spectral shape are observed as the degree of burn increases, and a simplified analysis is developed to infer scatter-averaged fluid velocity and temperature. The backscatter analysis offers direct measurement of the increased dense fuel temperatures that result from burn propagation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Optimization-Based Dynamic Voltage Support of Microgrids Using Energy Storage Systems

A microgrid network is characterized by a high R/X ratio, making the voltage more sensitive to active power changes compared to bulk power systems, where the voltage is regulated primarily by reactive power. Due to its sensitivity, voltage control approaches for microgrids should also consider the active power input coupling, making it very different from conventional power systems. Additionally, as the energy costs associated with active and reactive powers are different and the operational conditions of microgrids connected to active distribution systems vary over time, the ideal controller to provide voltage support must be flexible enough to handle these technical and operational constraints. This paper proposes a model predictive control approach to provide dynamic voltage support using energy storage systems. This approach uses a simplified predictive model of the system to solve the model predictive control problem. By proper selection of model predictive control weighting parameters, the quality of service provided can be adjusted to achieve the desired performance. A simulation study in MATLAB/Simulink validates the proposed approach for the Cordova, Alaska microgrid. Results show that the performance of the voltage support can be adjusted depending on the choice of weight and constraints of the controller.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Effect of cold cap coverage and emissivity on the plenum temperature in a pilot-scale waste vitrification melter

Integrated computational fluid dynamics (CFD) models are being developed to model the complex physics occurring within the high-level waste melter for vitrification of legacy tank waste at the Hanford site. Here, we present a validation of the integrated CFD model by using data from two experimental runs in a pilot-scale melter. While the model uses several simplifying assumptions (such as constant heat sinks from a cooling jacket and inleakage of ambient air, steady state feed-to-batch conversion heat, and a cold cap model with a simplified shape), it closely predicts the molten glass (1150°C and 1175°C) and plenum temperatures (550°C) obtained from thermocouples during two pilot-scale tests, with an average cold cap coverage of 80%. Additional simulations were performed to explore the sensitivity of the predicted plenum temperatures to variations in cold cap coverage (fraction of melt surface covered by the glass batch) and batch emissivity. The plenum temperature was found to be in the range of 606°C when cold cap coverage decreased from 95% to 70%. Cold cap emissivity had a smaller effect, increasing the plenum temperature by as much as 179°C when cold cap emissivity increased from 0.2 to 0.8. Maintaining a high cold cap coverage without overfeeding is important for a sustained melter operation with high glass throughput. This work provides a tool for achieving that goal in terms of correlating the plenum temperature with the cold cap coverage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Bichromatic Wave Selection for Validation of the Difference-Frequency Transfer Function for the OC6 Validation Campaign: Preprint

The focus of the Offshore Code Comparison Collaboration, Continuation, with Correlation and unCertainity (OC6) project, which operates under the International Energy Agency (IEA) Wind Task 30, is to refine the accuracy of engineering tools used to design offshore wind turbines. In support of this work, a new validation campaign is being developed that seeks to better understand the nonlinear wave loading that excites floating wind systems at their low-frequency, rigid-body modes in surge and pitch. The validation data will be used in a three-way validation between simplified engineering tools and higher-fidelity tools, such as computational fluid dynamics (CFD). Irregular wave spectrums, which are traditionally used to examine the nonlinear wave interaction with offshore structures, are too computationally expensive to be simulated in CFD tools, and so bichromatic wave cases will be used instead. This paper reviews the process used to choose the bichromatic wave pairs to be used in the campaign to validate the second-order difference-frequency quadratic and potential loads at the surge and pitch natural frequencies of a floating semisubmersible.

17 WIND ENERGY↗
DOE OSTI2022

Partial densities of states from x-ray absorption and Auger electron spectroscopy: Use of core-hole memory

Ag L 3 edge x-ray absorption and L 3 −M 4,5 M 4,5 Auger electron spectra have been measured and simulated for a variety of x-ray electric-field polarization and Auger electron emission directions. The theory relies on density-functional theory, use of the Bethe–Salpeter equation, atomic multiplet theory, and a simplified model for the Auger line shape and its dependence on photon energy. We also demonstrate that partial densities of states for dT 2g , dE g , and sA g symmetry partial-wave channels at the Ag site in the solid can be deduced from the experimental measurements with only atomic theoretical input, i.e., with no solid-state theory other than assuming a Fermi edge.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Verification and Validation of High Explosive Reactive Burn Models Implemented in LANL's EAP and LAP Code Base (FY2020 L2 Milestone MRT 7129) [Slides]

Advanced reactive burn models enable phenomena to be modeled that aren’t possible with programmed burn. Programmed burn propagates a burn front at a prescribed speed from a prescribed initiation point. Reactive burn uses the hydro variables (pressure, temperature, etc.) to determine when, how rapidly, and to what extent a zone detonates. This enables a completely new set of problems to be simulated. Our goal in this milestone has been to improve the usability of reactive burn modes. Thus, the closure criteria are: 1. Perform code and solution verification of the reactive burn models using appropriate solutions and simplified HE setups. 2. Perform validation assessments using small-scale experiments. 3. Evaluate sensitivities and quantify uncertainties due to model form variations and mesh dependencies.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2021

Unified Nanotechnology Format: One Way to Store Them All

The domains of DNA and RNA nanotechnology are steadily gaining in popularity while proving their value with various successful results, including biosensing robots and drug delivery cages. Nowadays, the nanotechnology design pipeline usually relies on computer-based design (CAD) approaches to design and simulate the desired structure before the wet lab assembly. To aid with these tasks, various software tools exist and are often used in conjunction. However, their interoperability is hindered by a lack of a common file format that is fully descriptive of the many design paradigms. Therefore, in this paper, we propose a Unified Nanotechnology Format (UNF) designed specifically for the biomimetic nanotechnology field. UNF allows storage of both design and simulation data in a single file, including free-form and lattice-based DNA structures. By defining a logical and versatile format, we hope it will become a widely accepted and used file format for the nucleic acid nanotechnology community, facilitating the future work of researchers and software developers. Together with the format description and publicly available documentation, we provide a set of converters from existing file formats to simplify the transition. Finally, we present several use cases visualizing example structures stored in UNF, showcasing the various types of data UNF can handle.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

A simple model for short-range ordering kinetics in multi-principal element alloys

Short-range ordering (SRO) in multi-principal element alloys influences material properties such as strength and corrosion. While some degree of SRO is expected at equilibrium, predicting the kinetics of its formation is challenging. We present a simplified isothermal concentration-wave (CW) model to estimate an effective relaxation time of SRO formation. Estimates from the CW model agree to within a factor of five with relaxation times obtained from kinetic Monte Carlo (kMC) simulations when above the highest ordering instability temperature. Further, the advantage of the CW model is that it only requires mobility and thermodynamic parameters, which are readily obtained from alloy mobility databases and Metropolis Monte Carlo simulations, respectively. The simple parameterization of the CW model and its analytical nature makes it an attractive tool for the design of processing conditions to promote or suppress SRO in multicomponent alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A classical equation that accounts for observations of non-Arrhenius and cryogenic grain boundary migration

Observations of microstructural coarsening at cryogenic temperatures, as well as numerous simulations of grain boundary motion that show faster migration at low temperature than at high temperature, have been troubling because they do not follow the expected Arrhenius behavior. This work demonstrates that classical equations, that are not simplified, account for all these oddities and demonstrate that non-Arrhenius behavior can emerge from thermally activated processes. According to this classical model, this occurs when the intrinsic barrier energies of the processes become small, allowing activation at cryogenic temperatures. Additional thermal energy then allows the low energy process to proceed in reverse, so increasing temperature only serves to frustrate the forward motion. This classical form is shown to reconcile and describe a variety of diverse grain boundary migration observations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermo-Mechanical Distortion of Tungsten-Coated Steel During High Heat Flux Testing Using Plasma Arc Lamps

An experimental setup and a test section were designed and fabricated for high heat flux testing (HHFT) of neutron-irradiated specimens using water-wall plasma arc lamps. Because of the radiological considerations and limitations of reactor irradiation, the size of the test articles was limited to disks less than 10 mm in diameter. The specimen was clamped onto an actively cooled block, and clamping allowed the insertion of several thermocouples on the back surface of the specimen through a copper (Cu) block. Five vacuum plasma sprayed tungsten (W)–coated F82H steel specimens were subjected to HHFT. Surface profilometry measurements, which were conducted after HHFT, revealed central bowing of the top W surface. This type of residual distortion occurred for all of the specimens, and the larger the specimens were, the larger was the distortion.In an attempt to understand specimen distortion and address the science questions related to the testing of subsize specimens during HHFT, a simplified thermo-mechanical model was developed. By using a measured temperature in the Cu as an isothermal boundary condition, the model eliminated the need for coupling cooling fluid flow models with stress models, greatly simplifying the analysis. The main variable in the proposed model is hC, i.e., the thermal contact conductance between the F82H and the Cu washer. Inelastic properties, including hardening properties, were considered for F82H steel and Cu. Numerical simulation results demonstrated a buildup of residual deformation during HHFT and a very complex state of stress and deformation during typical heat flux (HF) cycling. Additionally, hoop stress evolution during a high heat flux cycle reveals that F82H at an interface with W would be mainly in compression during HF application and experienced a transition to a tension state during cooldown. Also, specimen distortion evolves during each HF cycle, as the specimen bows downward during HF application and upward during the cooldown period between HF cycles. The final specimen distortion, i.e., upward bowing of the specimen center, was qualitatively predicted for hC values of 4000 to 5000 W/(m 2 ·K). This hC range of values, for which bulging is obtained, is at the lower spectrum of the range of values for hC, consistent with the low thermal contact conductance expected from the unpolished F82H surface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Effective Permeability of a Nuclear Fuel Assembly

This report aids in the development of models to perform characterization studies of aerosol dispersal and deposition within a spent fuel cask system. Due to the complex geometry in a spent-fuel canister, direct simulation of buoyancy-driven flow through the fuel assemblies to model aerosol deposition within the fuel canister is computationally expensive. Identification of an effective permeability as given in this work for a nuclear fuel assembly greatly simplifies the requirements for thermal hydraulic computations. The results of computations performed using OpenFOAM® to solve the Navier-Stokes Equations for laminar flow are used to determine an effective permeability by applying Darcy's Law. The computations are validated against an analytical solution for the special case of an infinite array of pins for which the numerical and analytical solutions have excellent agreement. The effective permeability of a 1717 PWR nuclear fuel assembly in a basket without spacer grids is numerically determined to be 1.85010 -6 m 2 for the range of fluid viscosities and pressure drops expected in a spent fuel storage canister. However, the flow is not uniform on the scale of multiple pins. Instead, significantly higher velocities are attained in the space between the assembly and the basket walls compared to the flow between the fuel pins within the assembly. Comparison with an analytical solution for fully developed flow through an infinite array of pins shows that the larger spacing near the basket walls results in about a 20% larger permeability compared to the analytical solution which does not include the enhanced flow in the space between the assembly and basket wall, or entrance and exit effects. A preliminary assessment of turbulence effects shows that with a k-epsilon model, significantly higher flow velocities are attained between the fuel pins within the assembly compared to the flow velocity in the space between the assembly and the basket walls. This is the opposite of what is determined for laminar flow.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Implementing a Stochastic Soot Model in a 3D Domain

In this document a highly detailed stochastic soot model limited to 0D simulations is coupled to 3D domains through the use of a Lagrangian parcel-Eulerian fluid method. Although both the stochastic soot model used and the Lagrangian parcel-Eulerian fluid method have long histories of development, their use, as described in this document, is novel and useful. Previous works significant to the model's development include documents from both the stochastic and simpler soot model genre and the fuel, aerosol, and other particle tracking and Lagrangian parcel-Eulerian fluid genres. Developing the theory behind the model is crucial to its implementation because of the unconventional Lagrangian parcel-Eulerian fluid representation. In fact, the Lagrangian parcel-Eulerian fluid coupling is only a means of simplifying the much more difficult theoretical model. Despite the accompanying assumptions, the complete model is validated from the bottom up and then again in a holistic fashion with promising results. Then the model is used in multiple case studies, showcasing capabilities not had by other models. The optical properties of soot generated in a Spray A simulation are calculated to find measured results are likely overpredicting the mass of soot along the central axis via KL extinction measurements. A thermophoresis submodel that calculates force based on the soot particles' shape is installed to find it has a high influence on the path of the heaviest soot particles. Investigations into the HACA mechanism for soot growth and the effect of syngas on soot in 3D domains are performed with much more detail than has been available before.

Strickland, Tyler↗
DOE OSTI2024

Novel data interpretation method for DIII-D divertor retarding field energy analyzer with 3-D particle-in-cell simulations

A novel data interpretation process that utilizes comprehensive particle-in-cell (PIC) simulations is developed for the new retarding field energy analyzer (RFEA) currently being constructed at DIII-D for the lower divertor using the Divertor Material Evaluation System. Furthermore, this probe is expected to survive a heat load of up to 100 MW/m 2 for up to 5 s and reliably measure the main ion temperature (T i ) on the divertor target ranging from 10 to 200 eV. These extreme conditions posed significant engineering limitations on the probe geometry, thus extensive validation work has been performed. The conventional fitting method for the RFEA I–V characteristics is based on a simplified 1-D model without considering the ion space charge inside the probe cavity and may not be sufficient for probes designed for the DIII-D divertor environment. In this article, a more realistic description of the particle propagation process within the RFEA cavity is achieved by including both 3-D geometric effects and ion space charge in the PIC simulations, and the capability to reconstruct the ion energy distribution functions is demonstrated with reasonable consistency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Noise Robustness and Experimental Demonstration of a Quantum Generative Adversarial Network for Continuous Distributions

Abstract The potential advantage of machine learning in quantum computers is a topic of intense discussion in the literature. Theoretical, numerical, and experimental explorations will most likely be required to understand its power. There have been different algorithms proposed to exploit the probabilistic nature of variational quantum circuits for generative modeling. In this paper, a hybrid architecture for quantum generative adversarial networks (QGANs) is employed and their robustness in the presence of noise is studied. A simple way of adding different types of noise to the quantum generator circuit is devised, and the noisy hybrid QGANs (HQGANs) are simulated numerically to learn continuous probability distributions, and to show that the performance of HQGANs remains unaffected. The effect of different parameters on the training time is also investigated to reduce the computational scaling of the algorithm and simplify its deployment on a quantum computer. The training on Rigetti's Aspen‐4‐2Q‐A quantum processing unit is then performed, and the results from the training are presented. The authors' results pave the way for experimental exploration of different quantum machine learning algorithms on noisy intermediate‐scale quantum devices.

Anand, Abhinav↗
DOE OSTI2024

Understanding the impact of an applied axial magnetic field on efficient current coupling on the Z machine

Magnetized liner inertial fusion (MagLIF) is an attractive concept for producing thermonuclear fusion reactions. The MagLIF platform involves the operation of Helmholtz coils to apply a 15 Tesla axial magnetic field to the load region, where a cylindrical, fuel-filled metal liner is imploded by a ∼ 2 0 MA current pulse. The fringe field from these coils extends into the transmission line that delivers the current to the target. We investigated the extent to which this applied field disturbs the nominal power flow within that transmission line. A simplified model of the geometry shows that adding the applied magnetic field results in magnetic field lines that connect the cathode to the anode, suggesting electrons may not be magnetically insulated in this region. Particle-in-cell simulations indicated the addition of the applied magnetic field would not significantly impact the current delivery to the load. Velocimetry was used to experimentally assess the current delivery with and without the applied magnetic field. We find no measurable effects of the applied field on current delivery in the configuration investigated in this study. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Probabilistic Evaluation of Geomechanical Risks in CO2 Storage: An Exploration of Caprock Integrity Metrics Using a Multilaminate Model

The probabilistic uncertainty assessment of geomechanical risk—specifically, caprock failure—attributable to CO2 injection, as presented in a simplified hypothetical geological model, was the focus of this study. Our approach amalgamates the implementation of a multilaminate model, the creation of a response surface model in conjunction with the Box–Behnken sampling design, the execution of associated numerical modeling experiments, and the utilization of Monte Carlo simulations. Probability distributions to encapsulate the inherent variability (elastic and mechanical properties of the caprock and reservoir) and uncertainty in prediction estimates (vertical displacement, total strain, and F value) were employed. Our findings reveal that the Young modulus of the caprock is a key factor controlling equivalent total strain but is insufficient as a stand-alone indicator of caprock integrity. It is confirmed that the caprock can accommodate significant deformation without failure, if it possesses a low Young’s modulus and high mechanical strength properties, such as the friction angle and uniaxial compressive strength. Similarly, vertical displacement was found to be an unreliable indicator for caprock integrity, as caprock failure can occur across a broad spectrum of vertical displacements, particularly when both the Young modulus and mechanical strength properties have wide ranges. This study introduces the F value as the most dependable indicator for caprock failure, although it is a theoretical attribute (the shortest distance between the Mohr circle and the nearest failure envelope used to measure the sensitivity to failure) and not physically measurable in the field. Deviatoric stress levels were found to vary based on stress regimes, with the maximum levels observed under extensive and compressive stress regimes. In conjunction with the use of the response surface method, this study demonstrates the efficacy of the multilaminate framework and the Mohr–Coulomb constitutive model in providing a simplified, yet effective, probabilistic model of the mechanical behavior of caprock failure, reducing mathematical and computational complexities.

Energy & Fuels↗
DOE OSTI2021

Effect of chlorine and chromium on sulfur solubility in low-activity waste glass

According to an empirical sulfur solubility model developed from over 200 simulated low-activity waste (LAW) glasses, chlorine and chromium show strong effects on lowering sulfur solubility in glass. This work was aimed at understanding the mechanism behind the negative effect of chlorine and chromium on sulfur solubility. A simplified LAW glass was prepared and saturated by sodium sulfate, sodium chloride, and sodium chromate salts as single components and as mixtures with different ratios at 25 mol%, 50 mol%, and 75 mol% of sulfate mixed with chloride or chromate. A crucible-scale salt-saturation was performed by mixing the crushed glass powder with an excess amount of salts, melting at 1150 °C for one hour, and quenching. Three mixing-melting-quenching cycles were applied to determine saturation concentrations of sulfur, chromium, and chlorine incorporated into the simplified LAW glass. The glass compositions were analyzed by inductively coupled plasma–atomic emission spectroscopy, ion chromatography, and X-ray emission spectroscopy. It is proposed that the negative effect of chlorine and chromium on sulfur solubility can be explained based on the simple hypothesis that sulfur, chlorine, and chromium are present in the glass as anions competing for the voids or interstitial sites of the glass matrix, and that their solubility strongly depends on the effective size of corresponding anions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Methodology to assess “no-touch” building audit software using simulated utility data

Building audits are conducted in many commercial buildings to identify opportunities to reduce energy costs and improve building operation. Because audits require significant effort by building engineers, they are usually only affordable for larger commercial buildings. “No-touch” building audit tools have thus been developed to identify potential savings based on a simplified analysis of building energy consumption patterns via high-level energy data such as monthly utility bills. This paper presents a comprehensive and standardized methodology to evaluate the accuracy of no-touch audit tools in detecting and diagnosing building energy problems and quantifying potential energy savings. The test suite is based on output data from a well-characterized set of building energy models, and the methodology is illustrated by applying it to a representative no-touch building audit tool. Results show that the tool estimates building energy end uses with reasonable accuracy but is less accurate in identifying probably causes of high energy.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗