SEARCH · Engineering Papers

Results for “SURFACE DISTORTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Coherent Effects in Microwave Backscattering Models for Forest Canopies

In modeling forest canopies, several scattering mechanisms are taken into account: 1) volume scattering, 2) surface-volume interaction, and 3) surface scattering from forest floor. Depending on the structural and dielectric characteristics of forest canopies, the relative contribution of each mechanism in the total backscatter signal of an imaging radar can vary. In this paper, two commonly used first order discrete scattering models, Distorted Born Approximation (DBA) and Radiative Transfer (RT) are used to simulate the backscattered power received by polarimetric radars at P-, L-, and C-bands over coniferous and deciduous forests. The difference between the two models resides on the coherent effect in the surface-volume interaction terms.

Microwave Backscattering Models↗

DOE OSTI2020

Hierarchical Defect Engineering for LiCoO 2 through Low-Solubility Trace Element Doping

Real-world industry-relevant battery composite electrodes are hierarchically structured. Their structural and chemical complexity is featured by ubiquitous multi-scale porosity and cracks, solid-solid and solid-liquid interfaces, compositional and redox heterogeneity, as well as lattice disordering and deformation. In particular for the active cathode particles, which are the fundamental building blocks for the energy reservoir, it is a consensus that these structural and chemical defects could have a profound impact on the battery performance. An in-depth understanding of the underlying mechanisms could critically inform the cathode material engineering, which would have a tremendous potential but remains a daunting challenge at present. In this work, we tackle this question by studying LiCoO 2 (LCO) with trace doping of Ti, which exhibits a low solubility in the LCO layered lattice. Additionally, we observed the spontaneous and heterogeneous segregation of the dopant (Ti) across a wide range of length scales. In addition to the modification of the particle surface and the buried grain boundaries within the particle, we reveal that the Ti doping has induced a significant amount of lattice distortions, which, in turn, promotes the robustness of the LCO lattice at high state of charge (above 4.5V). Our result formulates a multi-scale defect engineering strategy that could be applicable to the synthesis of a broad range of energy materials for applications in batteries and beyond.

36 MATERIALS SCIENCE↗

NASA NTRS1975

Study of hollow corner retroreflectors for use in a synchronous orbit

The performance of a hollow corner cube retroreflector made up of three mutually perpendicular optically flat mirrors when undergoing the thermal-mechanical strains induced by a spacecraft environment was studied. Of particular interest was a device of 200 square centimeter optical aperture used on a satellite in a synchronous orbit. It was assumed that the reflector always faces the earth. The effects of direct solar irradiance, earthshine, and albedo were considered. The results included the maximum mirror surface temperature during the orbit as well as the worst-case loss of optical performance due to thermally-induced mirror distortions. It was concluded that a device made of three suitably coated flat ULE mirrors, optically contacted to each other and supported mechanically in a nonrigid mount, would be expected to concentrate over 80 percent of the theoretical maximum energy in the central of the far field diffraction pattern. Continued development of the device through a detailed design, fabrication, and test phase was recommended.

Yoder, P. R., Jr.↗

NASA NTRS1994

Neutral ion sources in precision manufacturing

Ion figuring of optical components is a relatively new technology that can alleviate some of the problems associated with traditional contact polishing. Because the technique is non contacting, edge distortions and rib structure print through do not occur. This initial investigation was aimed at determining the effect of ion figuring on surface roughness of previously polished or ductile ground ceramic optical samples. This is the first step in research directed toward the combination of a pre-finishing process (ductile grinding or polishing) with ion figuring to produce finished ceramic mirrors. The second phase of the project is focusing on the development of mathematical algorithms that will deconvolve the ion beam profile from the surface figure errors so that these errors can be successfully removed from the optical components. In the initial phase of the project, multiple, chemical vapor deposited silicon carbide (CVD SiC) samples were polished or ductile ground to specular or near-specular roughness. These samples were then characterized to determine topographic surface information. The surface evaluation consisted of stylus profilometry, interferometry, and optical and scanning electron microscopy. The surfaces, were ion machined to depths from 0-5 microns. The finished surfaces were characterized to evaluate the effects of the ion machining process with respect to the previous processing methods and the pre-existing subsurface damage. The development of the control algorithms for figuring optical components has been completed. These algorithms have been validated with simulations and future experiments have been planned to verify the methods. This paper will present the results of the initial surface finish experiments and the control algorithms simulations.

Fawcett, Steven C.↗

NASA NTRS1997

Detection of aseismic creep along the San Andreas fault near Parkfield, California with ERS-1 radar interferometry

The differential interferometric analysis of ERS data from Parkfield (CA) observations revealed the wide area distribution of creep along the moving fault segment of the San Andreas fault over a 15 month interval. The removal of the interferometric phase related to the surface topography was carried out. The fault was clearly visible in the differential interferogram. The magnitude of the tropospheric water vapor phase distortions is greater than the signal and hinders quantitative analysis beyond order of magnitude calculations.

Werner, Charles L.↗

NASA NTRS2010

L Band Brightness Temperature from Forest: Comparison of Approximate Techniques

In this paper, three approximate physical microwave radiometry models have been used to calculate brightness temperatures from a forest canopy at L-band. These models are (1) tau-omega model (zero order scattering approximation to radiative transfer equations), (2) successive order of scattering model up to first order (first order scattering approximation to the radiative transfer equations), and (3) Peak technique utilizing the active solution obtained from the Distorted Born Approximation (DBA). These models are physically-based and treat vegetation as a layer of discrete scatterers over a rough surface. Vegetation components within the canopy are represented by canonical shapes such as dielectric discs and cylinders. The tau-omega model is based on a zero-order solution to the radiative transfer (RT) equations. The model ignores scattering except for the effect of the scatterers in the attenuation of the emission through the vegetation. Application of the tau-omega model to data acquired during airborne and ground-based campaigns over the years has solidified scientific understanding of microwave interactions with different landscapes. In particular, shrubland, grasslands, agricultural crops, and light to moderate vegetation have been investigated. Its applicability to areas with a significant tree fraction is unknown. The first order scattering model is based on an iterative solution of the RT equation up to the first order. The first order solution is obtained by substituting the zeroth-order solution into the scattering source term and then solving the resulting radiative transfer equations. This formulation adds a new scattering term to the tau-omega model. It represents emission by particles in the layer and emission by the ground that is scattered once by particles in the layer. The resulting model represents an improvement over the standard zero-order solution (the tau-omega model) since it accounts for the scattered vegetation and ground radiation that can have a pronounced effect on the observed brightness temperature. The third model is based on the Peake formulation in conjunction with the DBA. The procedure for calculation of forest emission is accomplished by first calculating the bistatic scattering cross section for each type of scatterer, then by using the DBA to calculate specular albedo of the ground and the diffused albedo of the layer. Once the albedos are determined, Peake s principle relating active and passive problems can be used to determine the effective emissivity of the forest layer.

Kurum, Mehmet↗

NASA NTRS1978

Short-term performance deterioration in JT9D-7A(SP) engine 695743

The level of performance deterioration that occurred during early service was studied and also the contribution of each engine module to the overall level of engine performance deterioration. To assist in the distribution of the performance losses to the module level, testing with expanded experimental instrumentation was accomplished to permit direct measurement of module performance. An analytical teardown of the engine was accomplished to permit assignment of module performance losses to individual mechanical damage mechanisms including blade and seal wear, roughness, and thermal distortion of turbine parts. The results of the testing show that the engine deteriorated 1.5 percent in thrust specific fuel consumption from its performance when new. Initial testing, which included water washing, showed that 0.2 percent in performance deterioration was due to surface contamination (dirt) and 0.1 percent was due to drift of the engine vane control system, leaving 1.2 percent in basic TSFC deterioration. This 1.2 percent TSFC loss was distributed among the engine modules with 0.6 percent caused by clearance changes, 0.4 percent loss due to thermal distortion, and 0.2 percent loss due to increased roughness of the fan and low-pressure compressor airfoils.

Bouchard, R. J.↗

DOE OSTI2020

Distortions of the Rain Distribution With Warming, With and Without Self-Aggregation

We investigate how mesoscale circulations associated with convective aggregation can modulate the sensitivity of the hydrologic cycle to warming. We quantify changes in the full distribution of rain across radiative-convective equilibrium states in a cloud-resolving model. For a given Sea Surface Temperature (SST), the shift in mean rainfall between disorganized and organized states is associated with a shift in atmospheric radiative cooling, and is roughly analogous to the effect of a 4K SST increase. With rising temperatures, the increase in mean rain rate is insensitive to the presence of organization, while extremes can intensify faster in the aggregated state, leading to a faster amplification in the sporadic nature of rain. When convection aggregates, heavy rain is enhanced by 20%–30% and nonlinear behaviors are observed as a function of SST and strength of aggregation feedbacks. First, radiative- and surface-flux aggregation feedbacks have multiplicative effects on extremes, illustrating a non-trivial sensitivity to the degree of organization. Second, alternating Clausius-Clapeyron and super-Clausius-Clapeyron regimes in extreme rainfall are found as a function of SST, corresponding to varying thermodynamic and dynamic contributions, and a large sensitivity to precipitation efficiency variations in some SST ranges. The potential for mesoscale circulations in amplifying the hydrologic cycle is established. However, these nonlinear distortions question the quantitative relevance of idealized self-aggregation. This calls for a deeper investigation of relationships which capture the coupling between global energetics, aggregation feedbacks and local convection, and for systematic tests of their sensitivity to domain configurations, surface boundary conditions, microphysics, and turbulence schemes.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2017

Vortex Generators in a Streamline-Traced, External-Compression Supersonic Inlet

Vortex generators within a streamline-traced, external-compression supersonic inlet for Mach 1.66 were investigated to determine their ability to increase total pressure recovery and reduce total pressure distortion. The vortex generators studied were rectangular vanes arranged in counter-rotating and co-rotating arrays. The vane geometric factors of interest included height, length, spacing, angle-of-incidence, and positions upstream and downstream of the inlet terminal shock. The flow through the inlet was simulated numerically through the solution of the steady-state, Reynolds-averaged Navier-Stokes equations on multi-block, structured grids using the Wind-US flow solver. The vanes were simulated using a vortex generator model. The inlet performance was characterized by the inlet total pressure recovery and the radial and circumferential total pressure distortion indices at the engine face. Design of experiments and statistical analysis methods were applied to quantify the effect of the geometric factors of the vanes and search for optimal vane arrays. Co-rotating vane arrays with negative angles-of-incidence positioned on the supersonic diffuser were effective in sweeping low-momentum flow from the top toward the sides of the subsonic diffuser. This distributed the low-momentum flow more evenly about the circumference of the subsonic diffuser and reduced distortion. Co-rotating vane arrays with negative angles-of-incidence or counter-rotating vane arrays positioned downstream of the terminal shock were effective in mixing higher-momentum flow with lower-momentum flow to increase recovery and decrease distortion. A strategy of combining a co-rotating vane array on the supersonic diffuser with a counter-rotating vane array on the subsonic diffuser was effective in increasing recovery and reducing distortion.

computational fluid dynamics↗

NASA NTRS1997

An Inlet Distortion Assessment During Aircraft Departures at High Angle of Attack for an F/A-18A Aircraft

The F404-GE-400-powered F/A-18A High Alpha Research Vehicle (HARV) was used to examine the quality of inlet airflow during departed flight maneuvers, that is, during flight outside the normal maneuvering envelope where control surfaces have little or no effectiveness. Six nose-left and six nose-right departures were initiated at Mach numbers between 0.3 and 0.4 at an altitude of 35 kft. The entry yaw rates were approximately 40 to 90 deg/sec. Engine surges were encountered during three of the nose-left and one of the nose-right departures. Time-variant inlet-total-pressure distortion levels at the engine face did not significantly exceed those at maximum angle-of-attack and sideslip maneuvers during controlled flight. Surges caused by inlet distortion levels resulted from a combination of high levels of inlet distortion and rapid changes in aircraft position. These rapid changes indicate a combination of engine support and gyroscopic loads being applied to the engine structure that impact the aerodynamic stability of the compressor through changes in the rotor-to-case clearances. This document presents the slides from an oral presentation.

Steenken, William G.↗

NASA NTRS1991

Fundamental studies of rotor wakes in low speed forward flight using wide-field shadowgraphy

Experiments were conducted using the wide-field shadowgraph method to visualize the wake geometry from a helicopter rotor in low speed forward flight. The experiments were performed with an isolated rotor and with a body representing a helicopter fuselage. Particular attention was paid to documenting the isolated rotor wake geometry, blade vortex interaction phenomena near the rotor plane, the distortion made to the wake due to the presence of the body, and detailing the interaction of the tip vortices with the body surface. Quantitative measurements were made of the wake trajectories as functions of wake age, as well as estimates of the tip vortex core radius. The results have provided many details of the rotor wake structure that are useful for validating rotor wake and rotor/body interactional models in forward flight. The use of the wide-field shadowgraph method offers an important tool for visualizing rotor wake vortices, and helping to understand the complex three-dimensional nature of rotor wakes in forward flight.

Leishman, J. G.↗

NASA NTRS1992

Modeling of SAR returns from a red pine stand

Bright P-band radar returns from red pine forests have been observed on synthetic aperture radar (SAR) images in Bangor, Maine. A plot of red pine trees was selected for the characterization and modeling to understand the cause of the high P-band returns. The red pine stand under study consisted of mature trees. Diameter at breast height (DBH) measurements were made to determine stand density as a function of tree diameter. Soil moisture and bulk density measurements were taken along with ground rough surface profiles. Detailed biomass measurements of the needles, shoots, branches, and trunks were also taken. These site statistics have been used in a distorted Born approximation model of the forest. Computations indicate that the direct-reflected or the double-bounce contributions from the ground are responsible for the high observed P-band returns for HH polarization.

Lang, R. H.↗

NASA NTRS2015

Charge Analyzer Responsive Local Oscillations

The first transatlantic radio transmission, demonstrated by Marconi in December of 1901, revealed the essential role of the ionosphere for radio communications. This ionized layer of the upper atmosphere controls the amount of radio power transmitted through, reflected off of, and absorbed by the atmospheric medium. Low-frequency radio signals can propagate long distances around the globe via repeated reflections off of the ionosphere and the Earth's surface. Higher frequency radio signals can punch through the ionosphere to be received at orbiting satellites. However, any turbulence in the ionosphere can distort these signals, compromising the performance or even availability of space-based communication and navigations systems. The physics associated with this distortion effect is analogous to the situation when underwater images are distorted by convecting air bubbles. In fact, these ionospheric features are often called 'plasma bubbles' since they exhibit some of the similar behavior as underwater air bubbles. These events, instigated by solar and geomagnetic storms, can cause communication and navigation outages that last for hours. To help understand and predict these outages, a world-wide community of space scientists and technologists are devoted to researching this topic. One aspect of this research is to develop instruments capable of measuring the ionospheric plasma bubbles. Figure 1 shows a photo of the Charge Analyzer Responsive to Local Oscillations (CARLO), a new instrument under development at NASA Marshall Space Flight Center (MSFC). It is a frequency-domain ion spectrum analyzer designed to measure the distributions of ionospheric turbulence from 1 Hz to 10 kHz (i.e., spatial scales from a few kilometers down to a few centimeters). This frequency range is important since it focuses on turbulence scales that affect VHF/UHF satellite communications, GPS systems, and over-the-horizon radar systems. CARLO is based on the flight-proven Plasma Local Anomalous Noise Environment (PLANE) instrument, previously flown on a U.S. Air Force low-Earth orbiting satellite, which successfully measured ion turbulence in five frequency decades from 0.1 Hz to 10 kHz (fig 2).

Krause, Linda Habash↗

NASA NTRS1988

Airborne Visible/Infrared Imaging Spectrometer (AVIRIS): Inflight radiometric calibration and the determination of surface reflectance

The inflight radiometric performance of AVIRIS is presented together with a comparison of methods of recovering surface spectral reflectance from the data. Performance is evaluated by comparing radiance predicted from AVIRIS with radiance generated from the LOWIRAN 6 atmospheric model and measured surface reflectance. Comparisons show apparent agreement to within a few percent between 1800 and 2450 nm. Between 600 and 1800 nm the response of AVIRIS is systematically low by as much as 70 percent, and between 400 and 600 nm it is higher than expected. These problems are traced to thermal distortions of the instrument, and to detachment during flight of optical fibers connecting foreoptics to two of four spectrometers in the instrument. Of three methods studied, an empirical one involving calibration curves constructed from field reflectance measurements returns accurate predictions of the surface reflectance independent of the actual radiometric significance of the flight data.

Conel, J. E.↗

NASA NTRS1994

NCAR CCM2 simulation of the modern Antarctic climate

The National Center for Atmospheric Research (NCAR) community climate model version 2 (CCM2) simulation of the circumpolar trough, surface air temperature, the polar vortex, cloudiness, winds, and atmospheric moisture and energy budgets are examined to validate the model's representation of the present-day Antarctic climate. The results show that the CCM2 can well simulate many important climate features over Antarctica, such as the location and intensity of the circumpolar trough, the coreless winter over the plateau, the intensity and horizontal distribution of the surface inversion, the speed and streamline pattern of the katabatic winds, the double jet stream feature over the southern Indian and Pacific oceans, and the arid climate over the continent. However, there are also some serious errors in the model. Some are due to old problems but some are caused by the new parameterizations in the model. The model errors over high southern latitudes can be summarized as follows: The circumpolar trough, the polar vertex, and the westerlies in midlatitudes are too strong; the semiannual cycle of the circumpolar trough is distorted compared to the observations; the low centers of the circumpolar trough and the troughs in the middle and upper troposphere are shifted eastward by 15 deg - 40 deg longitude; the surface temperatures are too cold over the plateau in summer and over the coastline in winter; the polar tropopause continues to have a cold bias; and the cloudiness is too high over the continent. These biases are induced by two major factors: (1) the cloud optical properties in tropical and middle latitudes, which cause the eastward shift of troughs and surface low centers and the error in the semiannual cycle, and (2) the cold bias of the surface air temperature, which is attributed to the oversimulation of cloudiness over the continent, especially during summer, and the uniform 2-m-thick sea ice. The constant thickness of sea ice suppresses the energy flux from the ocean to the atmosphere and hence reduces the air temperature near the coast during winter. Finally, although the simulated Antarctic climate still suffers these biases, the overall performance of the CCM2 is much better than that of the CCM1-T42. Therefore the CCM2 is good enough to be used for climate change studies, especially over Antarctica.

Tzeng, Ren-Yow↗

NASA NTRS2010

Thermal Deformation and RF Performance Analyses for the SWOT Large Deployable Ka-Band Reflectarray

A large deployable antenna technology for the NASA Surface Water and Ocean Topography (SWOT) Mission is currently being developed by JPL in response to NRC Earth Science Tier 2 Decadal Survey recommendations. This technology is required to enable the SWOT mission due to the fact that no currently available antenna is capable of meeting SWOT's demanding Ka-Band remote sensing requirements. One of the key aspects of this antenna development is to minimize the effect of the on-orbit thermal distortion to the antenna RF performance. An analysis process which includes: 1) the on-orbit thermal analysis to obtain the temperature distribution; 2) structural deformation analysis to get the geometry of the antenna surface; and 3) the RF performance with the given deformed antenna surface has been developed to accommodate the development of this antenna technology. The detailed analysis process and some analysis results will be presented and discussed by this paper.

thermal distorsion↗

NASA NTRS2020

1- by 1-Foot Supersonic Wind Tunnel Sidewall Flowfield Compression Plate Study

A method for locally increasing the dynamic pressure in the test section of a supersonic wind tunnel is investigated from a theoretical, computational and experimental perspective, culminating in a reduced-scale, proof-of-concept test at Mach 3.44. Symmetric, variable-angle compression plates along the test section sidewalls generate oblique shockwaves to elevate the test section dynamic pressure (q). The experimental effort utilizes boundary-layer pitot rakes to sample the incoming flow near the floor, pitot and static rakes to measure the high-q core flow and numerous surface taps to map out the static pressure distribution along the floor, ceiling and sidewalls. A reliable and robust starting procedure is developed to establish supersonic flow in the test section and behind the compression plates. A characterization of the incoming floor boundary layer reveals previously documented features (such as a bulge toward the centerline) and an unexpected (and as-yet-unexplained) thickening of the boundary layer with increasing Reynolds number around total pressures of 40–60 psia. The high-q core flow is characterized for eight compression plate angles (4.0–8.0°), eight tunnel total pressures (20–139 psia) and three axial stations (24.95–27.35 inches). The peak dynamic pressure rise exceeds expectations. At conditions relevant to full-scale testing (6.0° and 139 psia), the dynamic pressure increases by a factor of 1.73, the Mach number becomes 2.85 and the total pressure drops imperceptibly. Basic distortion metrics show transverse non-uniformity of less than 5 %. Limited spatial resolution in the static rake measurements warrants additional, higher fidelity testing or computational analysis. Surface-mounted, fast-response instrumentation suggests minimal unsteadiness in the flow, less than a few percent of the mean (comparable to the sensor accuracy).

Wind tunnel testing, test techniques/methods, dyna↗

NASA NTRS1980

An analysis of short pulse and dual frequency radar techniques for measuring ocean wave spectra from satellites

Scanning beam microwave radars were used to measure ocean wave directional spectra from satellites. In principle, surface wave spectral resolution in wave number can be obtained using either short pulse (SP) or dual frequency (DF) techniques; in either case, directional resolution obtains naturally as a consequence of a Bragg-like wave front matching. A four frequency moment characterization of backscatter from the near vertical using physical optics in the high frequency limit was applied to an analysis of the SP and DF measurement techniques. The intrinsic electromagnetic modulation spectrum was to the first order in wave steepness proportional to the large wave directional slope spectrum. Harmonic distortion was small and was a minimum near 10 deg incidence. NonGaussian wave statistics can have an effect comparable to that in the second order of scattering from a normally distributed sea surface. The SP technique is superior to the DF technique in terms of measurement signal to noise ratio and contrast ratio.

Jackson, F. C.↗