Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Full time-dependent SOLPS-ITER simulation of the SPARC tokamak: actuator design for particle and divertor condition control *

Abstract This paper presents the application of full time-dependent SOLPS-ITER simulations for actuator design in the SPARC tokamak. This study employs both the EIRENE module, a neutral solver, and the B2.5 plasma module in a time-dependent mode. This is in contrast to most SOLPS simulations, which focus on steady-state solutions, where the neutral distribution is evolved without any time limit or for a time step of 1 ⋅ 10 − 3 second, which is several orders of magnitude larger than the fluid plasma time step. The time-dependent EIRENE was tested with a fixed B2.5 background and compared with a simple conductance based model in a simplified pump chamber geometry. This comparison aimed to verify the reliability of the neutral relaxation timescale derived from the time-dependent EIRENE. Subsequently, a full time-dependent simulation was performed in a realistic geometry, with the Monte-Carlo neutral time step synchronized with the plasma fluid time step. The numerical setup of the code, including relative time steps and the size of the census data used to store Monte-Carlo particle information is considered. The full-time dependent simulations are then applied to inform the design of the SPARC louver structure, which affects divertor plasma parameters by regulating the neutral conductance from the divertor to the pump. The response of the plasma and neutral parameters was captured on a timescale that enables the design of the actuator to consider time-dependent control capability. It was found that changing the louver opacity has an equivalent effect as varying the gas throughput via puff actuation. Therefore, equivalent divertor plasma conditions can be obtained from both actuators, while the neutral pressure distribution in the pump and divertor differs for each actuator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

High-energy X-ray imaging with a Germanium MM-PAD hybrid pixel detector

Germanium is a high-Z sensor material with excellent energy resolution and attractive properties for high-energy photon detection. Despite its advantages, the need for cryogenic operation and challenges in the fabrication of pixelated high-purity germanium have hindered the development of segmented detectors. We report on the fabrication and performance of a germanium imaging detector with 150 μm pixel pitch hybridized to the MM-PAD ASIC. The detector was capable of high-resolution radiographic imaging and has a fast temporal response. Additionally, we describe the detector's upper operating temperature limits using both the MM-PAD and MARS ASICs, achieving stable operation up to 130 K and 190 K, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Characterization of high-flux cadmium zinc telluride detectors coupled to MM-PAD readout ASICs for high-flux X-ray applications

High-flux cadmium zinc telluride (HF-CZT) is a promising material for next-generation X-ray imaging due to its high stopping power, wide bandgap, and improved resistance to radiation-induced polarization [1]. We bonded 2 mm thick HF-CZT sensors with Cornell's Mixed-Mode Pixel Array ASICs, which combine analog charge integration and in-pixel digital counting to achieve single X-ray sensitivity, large full well capacity, and frame rates up to 10 kHz [2,3]. Detector characterization showed stable electron collection above 150 V bias, while hole collection remained limited by trapping even at 700 V. Temporal studies revealed non-negligible afterglow, with an unexpected increase in afterglow at higher biases, which was reduced by infrared illumination, suggesting that injected carriers reduce trapping near contact interfaces. Polarization measurements confirmed improved stability compared to conventional CZT, though polarization effects persisted, particularly with hole collection, with up to 5% signal loss and spatial distortion at high doses.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterizing electron-collecting CdTe for use in a 77 ns burst-rate imager

The Keck-PAD (pixel array detector) was developed at Cornell as a burst-rate imager capable of recording images from successive electron bunches (153 ns period) from the Advanced Photon Source (APS). Both Si and hole-collecting Schottky CdTe have been successfully bonded to this ASIC (application-specific integrated circuit) and used with this frame rate. The facility upgrades at the APS will lower the bunch period to 77 ns, which will require modifications to the Keck-PAD electronics to image properly at this reduced period. In addition, operation at high X-ray energies will require a different sensor material having a shorter charge collection time. For the target energy of 40 keV for this project, simulations have shown that electron-collecting CdTe should allow >90% charge collection within 35 ns. This collection time will be sufficient to sample the signal from one frame and prepare for the next. 750 µm-thick electron-collecting Schottky CdTe has been obtained from Acrorad and bonded to two different charge-integrating ASICs developed at Cornell, the Keck-PAD and the CU-APS-PAD. Carrier mobility has been investigated using the detector response to single X-ray bunches at the Cornell High Energy Synchrotron Source and to a pulsed optical laser. The tests indicate that the collection time will meet the requirements for 77 ns imaging.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Leveraging BERT and Network-Based Attention Analysis for Identifying Treatment Milestones in EHRs

This study introduces a sophisticated data-driven framework for analyzing Electronic Health Records (EHRs) using transformer-based models to identify and disentangle overlapping treatment contexts. The framework leverages a preprocessing pipeline that transforms structured procedural codes into semantically enriched descriptive text, enabling the use of attention mechanisms to cluster medical events into treatment milestones—cohesive and distinct components of care processes. The methodology is rigorously validated using synthetic datasets derived from the MIMIC-III database, designed to simulate the heterogeneity and overlapping procedural contexts characteristic of real-world EHR scenarios. Quantitative evaluation highlights the framework’s robustness in disentangling concurrent care pathways, with attention metrics and unsupervised clustering approaches demonstrating the ability to preserve intra-context relationships while distinguishing inter-context dependencies. By addressing challenges inherent in data heterogeneity, this approach provides a foundation for uncovering complex treatment patterns, advancing clinical decision-making, and optimizing resource allocation in diverse healthcare environments.

Kim, Minsu [ORNL] (ORCID:0000000224185535)↗
DOE OSTI2021

A Parameterization of the Cloud Scattering Polarization Signal Derived From GPM Observations for Microwave Fast Radative Transfer Models

Microwave cloud polarized observations have shown the potential to improve precipitation retrievals since they are linked to the orientation and shape of ice habits. Stratiform clouds show larger brightness temperature (TB) polarization differences (PDs), defined as the vertically polarized TB (TBV) minus the horizontally polarized TB (TBH), with ~10 K PD values at 89 GHz due to the presence of horizontally aligned snowflakes, while convective regions show smaller PD signals, as graupel and/or hail in the updraft tend to become randomly oriented. The launch of the global precipitation measurement (GPM) microwave imager (GMI) has extended the availability of microwave polarized observations to higher frequencies (166 GHz) in the tropics and midlatitudes, previously only available up to 89 GHz. This study analyzes one year of GMI observations to explore further the previously reported stable relationship between the PD and the observed TBs at 89 and 166 GHz, respectively. The latitudinal and seasonal variability is analyzed to propose a cloud scattering polarization parameterization of the PD-TB relationship, capable of reconstructing the PD signal from simulated TBs. Given that operational radiative transfer (RT) models do not currently simulate the cloud polarized signals, this is an alternative and simple solution to exploit the large number of cloud polarized observations available. Finally, the atmospheric radiative transfer simulator (ARTS) is coupled with the weather research and forecasting (WRF) model, in order to apply the proposed parameterization to the RT simulated TBs and hence infer the corresponding PD values, which show to reproduce the observed GMI PDs well.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Characterization of a Small-Scale Prototype Detector With Wide Dynamic Range for Time-Resolved High-Energy X-Ray Applications

We present characterization measurements of a fast-framing, wide-dynamic-range x-ray area detector intended for high-energy applications (≥20 keV photons). The MM-PAD-2.1 combines an integrating pixel front-end with a charge-removal mechanism to extend the maximum measurable signal to > 107 20-keV ph/pixel/frame. The charge-removal mechanism is dead-time-less (i.e., incoming signal continues to be integrated by the front-end while charge removal is taking place) up to an incoming photon rate of > 109 20-keV ph/pix/s. A 16×16 pixel prototype was fabricated and characterized using both laboratory and synchrotron x-ray sources, allowing for measurements from single-photon to high-flux conditions. High-flux measurements show linear performance up to ~1010 ph/s in a spot spanning approximately 2×1.5 pixels (FWHM). The onset of temporary radiation damage in the detector was observed during these measurements, manifesting as failure of the digital readout from the detector. These effects were seen to reverse after annealing at 30° C for several hours.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Seismic fault weakening via CO 2 pressurization enhanced by mechanical deformation of dolomite fault gouges

Carbon dioxide emissions from dolomite decarbonation play an essential role in the weakening of carbonate faults by lowering the effective normal stress, which is thermally activated at temperatures above 600–700 °C. However, the mechanochemical effect of low-crystalline ultrafine fault gouge on the decarbonation and slip behavior of dolomite-bearing faults remains unclear. In this study, we obtained a series of artificial dolomite fault gouges with systematically varying particle sizes and dolomite crystallinities using a high-energy ball mill. The laboratory-scale pulverization of dolomite yielded MgO at temperatures below 50 °C, indicating that mechanical decarbonation without significant heating occurred due to the collapse of the crystalline structure, as revealed by X-ray diffraction and solid-state nuclear magnetic resonance results. Furthermore, the onset temperature of thermal decarbonation decreased to ~400 °C. Numerical modeling reproduced this two-stage decarbonation, where the pore pressure increased due to low-temperature thermal decarbonation, leading to slip weakening on the fault plane even at 400–500 °C; i.e., 200–300 °C lower than previously reported temperatures. Thus, the presence of small amounts of low-crystalline dolomite in a fault plane may lead to a severely reduced shear strength due to thermal decomposition at ~400 °C with a small slip weakening distance.

58 GEOSCIENCES↗
DOE OSTI2020

OSTI Semantic Thesaurus v1

The OSTI Semantic Thesaurus is a reference for scientific and technical terms and relationships. The term data is used to implement keyword-to-concept mapping in OSTI.GOV searches, where searched term(s) will be mapped to related scientific concepts, allowing the end user to retrieve results related to their search terms and also explore narrower and similar concepts. The OSTI Semantic Thesaurus originally inherited data and structure from the INIS/ETDE Thesaurus (https://www.etde.org/edb/IAEA-INIS-ETDE-01-2013-08.pdf), which was a controlled terminology for indexing information within the subject scopes of the International Nuclear Information System (INIS) and the Energy Technology Data Exchange (ETDE). The data has been expanded upon since that time with the inclusion of scientific concepts from sources like Wikidata, and through manual curation. This dataset is an export from the OSTI Semantic Thesaurus in RDF/SKOS format, which is specifically suited for representation of controlled vocabularies like thesauri. While the full thesaurus includes additional relation types which may be included in future revisions, this export is limited to broader, narrower, and related term relations. Definitions and scope notes are included where available.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2020

Detection Uncertainty Matters for Understanding Atmospheric Rivers

The 3rd ARTMIP Workshop What: Over 30 participants from multiple universities and research insititutions met to discuss new results from the Atmospheric River Tracking Method Intercomparison Project. Where: Lawrence Berkeley National Lab, Berkeley, CA, USA When: 16-18 October 2019

O'Brien, Travis↗
DOE OSTI2023

Community Based Data of Potentiometric Titration of Iron Oxides: Ferrihydrite (HFO), Goethite, Hematite, Magnetite

This data release includes experimental data of potentiometric titration for iron oxides. The data in the provided .csv files is not our own experimental data but have been compiled from the multiple literature sources. The master database is L-SCIE (LLNL Surface Complexation/Ion Exchange) database, and the provided .csv files are extracted data from L-SCIE. The .csv files were obtained by using the Lawrence Livermore National Laboratory Surface Complexation Database Converter (SCDC) code written in the R programming language (free licensing available at https://ipo.llnl.gov/technologies/software/llnl-surface-complexation-database-converter-scdc).The released data was used for developing a comprehensive community data-driven surface complexation modeling (SCM) framework for simulating potentiometric titration of mineral surfaces. Compiled community data for ferrihydrite, goethite, hematite, and magnetite are fit to produce representative protolysis constants that can reproduce potentiometric titration data collected from multiple literature sources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Deposition and dielectric characterization of highly oriented V 2 O 5 thin films

The possibility of ferroelectricity in orthorhombic V 2 O 5 thin flms was investigated. Films were deposited via either a chemical solution deposition (CSD) route or by RF magnetron sputtering. Highly (001) oriented V 2 O 5 flms were achieved with both deposition routes at temperatures as low as 300°C. No evidence for ferroelectricity was observed, even in flms which had been doped to provide local nuclei for polarization reversal. Loss originated from mid-gap trap states stemming from oxygen vacancies that were observed with photoluminescence, supplemented by piezoresponse force microscopy measurements. Furthermore, these trap states may have helped mimic ferroelectricity in previous reports on V 2 O 5 .

36 MATERIALS SCIENCE↗
DOE OSTI2023

Silver nanowire-indium zinc oxide composite flexible transparent conducting electrodes made by spin-coating and photonic curing

Flexible transparent conducting electrodes (TCE) play a critical role in modern technologies. Eliminating the high-temperature annealing of vacuum- or solution-deposited films will increase production throughput and lower the cost of the final products. Photonic curing uses intense pulses of broadband light to induce material transformations instead of heat. In this work, we combine solution deposition and photonic curing, replacing thermal annealing, to fabricate flexible composite TCE films on plastic polyethylene terephthalate (PET) substrates. The composite TCE films are composed of spin-coated silver nanowire-indium zinc oxide layers. Further, the TCE films’ electrical, optical, and morphological properties are investigated and compared to those of commercially available PET/TCE. A sheet resistance of 15 Ω/sq and an average transmittance from 400 – 700 nm of 77% are achieved with the spin-coated and photonic-cured composite flexible TCE films.

14 SOLAR ENERGY↗
DOE OSTI2022

M4SF-22LL010301062-Surface Complexation Database and Hybrid ML Model Development for GDSA

This progress report (Level 4 Milestone Number M4SF-22LL010301062) summarizes research conducted at Lawrence Livermore National Laboratory (LLNL) within the Argillite International Collaborations Activity Number Activity SF-22LL01030106. The activity is focused on our long-term commitment to engaging our partners in international nuclear waste repository research. The focus of this milestone is the establishment of international collaborations for surface complexation modeling and the associated impacts of unlocking larger, community-based datasets. More specifically, we are developing a database framework for Spent Fuel and Waste and Science Technology (SFWST) that is aligned with the Helmholtz Zentrum Dresden Rossendorf (HZDR) sorption database development group in support of the database needs of the SFWST program.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Nuclear Global Talent Development Program (Final Report)

Lawrence Livermore National Laboratory (LLNL) have developed sorption database named as L-SCIE (LLNL Surface Complexation/Ion Exchange). This framework (L-SCIE) includes not only a community database of sorption data but also a fitting workflow to produce optimized surface complexation reaction constants. Through this fellowship program we have updated the L-SCIE database for selenium (Se) sorption and potentiometric titration data of iron oxides. In addition, the relevant surface complexation models (SCMs) have been updated and details in model construction are given in the following section.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Advanced Mixed-Mode Pixel Array Detector for X-rays Above 20 keV (Final Report)

The objective of the work reported upon was to perform research and development and test advanced prototype imaging x-ray detectors needed to meet pressing scientific research needs at U.S. x-ray synchrotron user facilities. The high x-ray brightness of the Nation’s x-ray synchrotron sources in the DOE National Laboratories holds promise to advance science and technology in a broad range of fundamental and applied disciplines, including physics, chemistry, biomedical areas and engineering. At present, progress in many areas is being limited not by the x-ray source but by the lack of imaging x-ray detectors capable of meeting experimental needs. Specifically, there is pressing need for imaging detectors with high dynamic range, low noise, high frame rates and the ability to capture x-ray images with x-rays of energy > 20 keV. This Final Technical Report summarizes progress made at Cornell University on novel integrating x-ray detectors that address these characteristics.

36 MATERIALS SCIENCE↗