Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Powder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Demonstration of a silicon nitride attrition mill for production of fine pure Si and Si3N4 powders

To avoid metallic impurities normally introduced by milling ceramic powders in conventional steel hardware, an attrition mill (high-energy stirred ball mill) was constructed with the wearing parts (mill body, stirring arms, and media) made from silicon nitride. Commercial silicon and Si3N4 powders were milled to fine uniform particles with only minimal contamination - primarily from wear of the sintered Si3N4 media.

Herbell, T. P.↗
NASA NTRS1986

Ultrasonic characterization of microstructure in powder metal alloy

The ultrasonic wave propagation characteristics were measured for IN-100, a powder metallurgy alloy used for aircraft engine components. This material was as a model system for testing the feasibility of characterizing the microstructure of a variety of inhomogeneous media including powder metals, ceramics, castings and components. The data were obtained for a frequency range from about 2 to 20 MHz and were statistically averaged over numerous volume elements of the samples. Micrographical examination provided size and number distributions for grain and pore structure. The results showed that the predominant source for the ultrasonic attenuation and backscatter was a dense (approx. 100/cubic mm) distribution of small micropores (approx. 10 micron radius). Two samples with different micropore densities were studied in detail to test the feasibility of calculating from observed microstructural parameters the frequency dependence of the microstructural backscatter in the regime for which the wavelength is much larger than the size of the individual scattering centers. Excellent agreement was found between predicted and observed values so as to demonstrate the feasibility of solving the forward problem. The results suggest a way towards the nondestructive detection and characterization of anomalous distributions of micropores when conventional ultrasonic imaging is difficult. The findings are potentially significant toward the application of the early detection of porosity during the materials fabrication process and after manufacturing of potential sites for stress induced void coalescence leading to crack initiation and subsequent failure.

Tittmann, B. R.↗
NASA NTRS1985

Synthesis of ceramic powders and surface films from laser heated gases

Two new processes have been developed that are based on laser-heated gases. Both permit unusually precise levels of process control and, thereby, materials having superior properties. The power process yields Si, Si3N4 and SiC powders that are uniform in size, nonagglomerated, small diameter, spherically shaped and high purity. Manufacturing cost analyses show that submicron powders can be made with an energy cost of approximately 2 kWhr/kg and a dollar cost of 2-3.30 $/kg, exclusive of the costs of feed materials. The laser-induced chemical vapor deposition process (LICVD) causes reactant gases to be heated by absorbing IR light from a laser beam that passes parallel to the substrate surface. Laser heating permits independent control of gas and substrate temperatures while operating in a conventional, thermally activated chemical vapor deposition mode. Spin density, hydrogen content, electrical conductivity and mobility gap properties show the LICVD process capable of producing very high quality films.

Haggerty, J. S.↗
NASA NTRS1986

Submicron silicon powder production in an aerosol reactor

Powder synthesis by thermally induced vapor phase reactions is described. The powder generated by this technique consists of spherical, nonagglomerated particles of high purity. The particles are uniform in size, in the 0.1-0.2-micron size range. Most of the particles are crystalline spheres. A small fraction of the spheres are amorphous. Chain agglomerates account for less than 1 percent of the spherules.

Wu, J. J.↗
NASA NTRS1985

Processing of laser formed SiC powder

Superior SiC characteristics can be achieved through the use of ideal constituent powders and careful post-synthesis processing steps. High purity SiC powders of approx. 1000 A uniform diameter, nonagglomerated and spherical were produced. This required major revision of the particle formation and growth model from one based on classical nucleation and growth to one based on collision and coalescence of Si particles followed by their carburization. Dispersions based on pure organic solvents as well as steric stabilization were investigated. Although stable dispersions were formed by both, subsequent part fabrication emphasized the pure solvents since fewer problems with drying and residuals of the high purity particles were anticipated. Test parts were made by the colloidal pressing technique; both liquid filtration and consolidation (rearrangement) stages were modeled. Green densities corresponding to a random close packed structure (approx. 63%) were achieved; this highly perfect structure has a high, uniform coordination number (greater than 11) approaching the quality of an ordered structure without introducing domain boundary effects. After drying, parts were densified at temperatures ranging from 1800 to 2100 C. Optimum densification temperatures will probably be in the 1900 to 2000 C range based on these preliminary results which showed that 2050 C samples had experienced substantial grain growth. Although overfired, the 2050 C samples exhibited excellent mechanical properties. Biaxial tensile strengths up to 714 MPa and Vickers hardness values of 2430 kg/sq mm 2 were both more typical of hot pressed than sintered SiC. Both result from the absence of large defects and the confinement of residual porosity (less than 2.5%) to small diameter, uniformly distributed pores.

Haggerty, J. S.↗
NASA NTRS1986

Particle-size reduction of Si3N4 powder with Si3N4 milling hardware

The grinding of Si3N4 powder using reaction bonded Si3N4 attrition, vibratory, and ball mills with Si3N4 media was examined. The rate of particle size reduction and the change in the chemical composition of the powder were determined in order to compare the grinding efficiency and the increase in impurity content resulting from mill and media wear for each technique. Attrition and vibratory milling exhibited rates of specific surface area increase that were approximately eight times that observed in ball milling. Vibratory milling introduced the greatest impurity pickup.

Herbell, T. P.↗
NASA NTRS1989

Grinding Si3N4 Powder In Si3N4 Equipment

Three methods of grinding compared. Report based on study of grinding silicon nitride powder in preparation for sintering into solid ceramic material. Attrition, vibratory, and ball mills lined with reaction-bonded silicon nitride tested. Rates of reduction of particle sizes and changes in chemical compositions of powders measured so grinding efficiences and increases in impurity contents from wear of mills and media evaluated for each technique.

Herbell, Thomas P.↗
NASA NTRS1989

Processing polymeric powders

The concept of uniformly and continuously depositing and sinter-fusing nominal 0.1 to 40 microns dimensioned electrostatically charged polymer powder particles onto essentially uniformly spread 5 to 20 micron grounded continuous fiber tow to produce a respoolable thermoplastic composite two-preg was formulated at NASA Langley. The process was reduced to practice under a NASA grant at the University of Akron this spring. The production of tow-preg is called phase 1. The production of ultrafine polymer powders from 5 to 10 percent (wt) polymer solids in solvent is considered. This is phase 0 and is discussed. The production of unitape from multi tow-pregs was also considered. This is phase 2 and is also discussed. And another approach to phase 1, also proposed last summer, was scoped. This is phase 1A and is also discussed.

Throne, James L.↗
NASA NTRS1991

The development and evaluation of an alternative powder prepregging technique for use with LaRC-TPI/graphite composites

An alternative powder prepregging method for use with LaRC-TPI (a thermoplastic polyimide)/graphite composites is investigated. The alternative method incorporates the idea of moistening the fiber prior to powder coating. Details of the processing parameters are given and discussed. The material was subsequently laminated into small coupons which were evaluated for processing defects using electron microscopy. After the initial evaluation of the material, no major processing defects were encountered but there appeared to be an interfacial adhesion problem. As a result, prepregging efforts were extended to include an additional fiber system, XAS, and a semicrystalline form of the matrix. The semicrystalline form of the matrix was the result of a complex heat treating cycle. Using scanning electron microscopy (SEM), the fiber/matrix adhesion was evaluated in these systems relative to the amorphous/XAS coupons. Based on these results, amorphous and semicrystalline/AS-4 and XAS materials were prepregged and laminated for transverse tensile testing. The results of these tests are presented, and in an effort to obtain more information on the effect of the matrix, remaining semicrystalline transverse tensile coupons were transformed back to the amorphous state and tested. The mechanical properties of the transformed coupons returned to the values observed for the original amorphous coupons, and the interfacial adhesion, as observed by SEM, was better than in any previous sample.

Ogden, Andrea L.↗
NASA NTRS1991

Midinfrared (2.5-13.5 microns) reflectance spectra of powdered stony meteorites

Asteroid spectral measurements are presently approached via comparisons with reflectance spectra from 60 powdered meteorite samples representing 50 different meteorites. While the powdered meteorites have undergone alteration by exposure to water vapor and by hydrocarbon contamination characterized by absorption bands near 3.45 microns, they retain various other spectral features which render them useful for identification. While these features can be used independently to ascertain mineralogy and meteorite type, the use of the entire spectrum in a digital search library is preferred for successful identification.

Salisbury, John W.↗
NASA NTRS1992

Removing Undesired Fine Powder From Silicon Reactor

Fluidized-bed reactor produces highly pure polycrystalline silicon particles with diameters approximately greater than 400 micrometers. Operates by pyrolysis of silane in reaction zone, which is bed of silicon seed particles fluidized by flow of silane and carrier gas. Above reaction zone, gas mixture flows rapidly enough to entrain silicon powders, but not larger seed and product particles. Entrained particles swept out of reactor. Applicable to other processes such as production of fine metal and ceramic powders where control of sizes of product needed.

Flagella, Robert N.↗
NASA NTRS1991

A major advance in powder metallurgy

Ultramet has developed a process which promises to significantly increase the mechanical properties of powder metallurgy (PM) parts. Current PM technology uses mixed powders of various constituents prior to compaction. The homogeneity and flaw distribution in PM parts depends on the uniformity of mixing and the maintenance of uniformity during compaction. Conventional PM fabrication processes typically result in non-uniform distribution of the matrix, flaw generation due to particle-particle contact when one of the constituents is a brittle material, and grain growth caused by high temperature, long duration compaction processes. Additionally, a significant amount of matrix material is usually necessary to fill voids and create 100 percent dense parts. In Ultramet's process, each individual particle is coated with the matrix material, and compaction is performed by solid state processing. In this program, Ultramet coated 12-micron tungsten particles with approximately 5 wt percent nickel/iron. After compaction, flexure strengths were measured 50 percent higher than those achieved in conventional liquid phase sintered parts (10 wt percent Ni/Fe). Further results and other material combinations are discussed.

Williams, Brian E.↗
NASA NTRS1991

Flexible thermoset towpregs by electrostatic powder fusion coating

Thermoset prepregs of expoxy and polyimide have been produced by electrostatic deposition of charged fluidized polymer powders on spread continuous fiber tows. The powders are melted onto the fibers by radiant heating to adhere the polymer to the fiber. This process produces towpreg uniformly and rapidly without imposing severe stresses on the fibers. The towpregs produced by this novel process were consolidated to make unidirectional laminates for mechanical testing. Low void content samples have been made and demonstrated by C-scan and scanning electron microscopy. The mechanical properties of unidirectional laminates are equivalent to composites fabricated by conventional techniques.

Yang, Pei-Hua↗
NASA NTRS1993

Adjustable Powder Injector For Vacuum Plasma Sprayer

Attachment for plasma spray gun provides four degrees of freedom for adjustment of position and orientation at which powder injected externally into plasma flame. Manipulator provides for adjustment of pitch angle of injection tube: set to inject powder at any angle ranging from perpendicular to parallel to cylindrical axis. Scribed lines on extension bar and manipulator indicate pitch angle of extension tube. Collar changed to adapt injector to different gun.

Burns, D. H.↗
NASA NTRS1993

Production of Ultrafine, High-purity Ceramic Powders Using the US Bureau of Mines Developed Turbomill

Turbomilling, an innovative grinding technology developed by the U.S. Bureau of Mines in the early 1960's for delaminating filler-grade kaolinitic clays, has been expanded into the areas of particle size reduction, material mixing, and process reaction kinetics. The turbomill, originally called an attrition grinder, has been used for particle size reduction of many minerals, including natural and synthetic mica, pyrophyllite, talc, and marble. In recent years, an all-polymer version of the turbomill has been used to produce ultrafine, high-purity, advanced ceramic powders such as SiC, Si3N4, TiB2, and ZrO2. In addition to particle size reduction, the turbomill has been used to produce intimate mixtures of high surface area powders and whiskers. Raw materials, TiN, AlN, and Al2O3, used to produce a titanium nitride/aluminum oxynitride (TiN/AlON) composite, were mixed in the turbomill, resulting in strength increases over samples prepared by dry ball milling. Using the turbomill as a leach vessel, it was found that 90.4 pct of the copper was extracted from the chalcopyrite during a 4-hour leach test in ferric sulfate versus conventional processing which involves either roasting of the ore for Cu recovery or leaching of the ore for several days.

Hoyer, Jesse L.↗
NASA NTRS1991

Powder towpreg process development

The process for dry powder impregnation of carbon fiber tows being developed at LaRC overcomes many of the difficulties associated with melt, solution, and slurry prepregging. In the process, fluidized powder is deposited on spread tow bundles and fused to the fibers by radiant heating. Impregnated tows have been produced for preform, weaving, and composite materials applications. Design and operating data correlations were developed for scale up of the process to commercial operation. Bench scale single tow experiments at tow speeds up to 50 cm/sec have demonstrated that the process can be controlled to produce weavable towpreg. Samples were woven and molded into preform material of good quality.

Baucom, Robert M.↗
NASA NTRS1993

On the development of constitutive relations for metallic powders

This article describes the development of elastic and plastic constitutive relations as functions of relative density for partially consolidated -100 mesh aluminum powder. First, measurements of yield stress as a function of stress state and relative density are described. Measurements of the plastic strain increments associated with yielding in unconstrained compression tests and elastic properties, both as functions of relative density, are also described. The experimental results are combined with the associated flow rule to show that the yield surface is asymmetric with respect to hydrostatic tension and compression. Second, it is shown that the yield stress results can be represented by a two-part (capped Drucker-Prager) yield surface. The consolidation yield surface moves along the hydrostatic stress axis during densification, while the shear yield surface approaches the Mises yield surface. For the Al powder used in the present investigation, superposition of shear stress on a hydrostatic stress state aids the densification process. However, the hydrostatic stress requirement was found to be reduced by only about 20 pct for relative densities below 0.98.

Watson, T. J.↗
NASA NTRS1994

Making Semicrystalline Polyimide Powders

Semicrystalline polyimides with controlled molecular weights synthesized in process that yields polyimides in powder form. Powders with desirable melt-flow properties formed in reaction vessels, without grinding. Commercially attractive for fabrication of adhesive bonds, compression molding of shaped parts, and deposition onto reinforcing fibers for subsequent hot pressing into polyimide-matrix/fiber composites.

St. Clair, Terry L.↗