Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Oxidation behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Thermal Shock Behavior of Single Crystal Oxide Refractive Concentrators for High Temperatures Solar Thermal Propulsion

Single crystal oxides such as yttria-stabilized zirconia (Y2O3-ZrO2), yttrium-aluminum-garnet (Y3Al5O12, or YAG), magnesium oxide (MgO) and sapphire (Al2O3) have been considered as refractive secondary concentrator materials for high temperature solar propulsion applications. However, thermal mechanical reliability of the oxide components in severe thermal environments during space mission sun/shade transitions is of great concern. In this paper, critical mechanical properties of these oxide crystals are determined by the indentation technique. Thermal shock resistance of the oxides is evaluated using a high power CO, laser under high temperature-high thermal gradients. Thermal stress fracture behavior and failure mechanisms of these oxide materials are investigated under various temperature and heating conditions.

Zhu, Dongming↗

Memristive Behavior Enabled by Amorphous–Crystalline 2D Oxide Heterostructure

The emergence of memristive behavior in amorphous–crystalline 2D oxide heterostructures, which are synthesized by atomic layer deposition (ALD) of a few-nanometer amorphous Al 2 O 3 layers onto atomically thin single-crystalline ZnO nanosheets, is demonstrated. The conduction mechanism is identified based on classic oxygen vacancy conductive channels. ZnO nanosheets provide a 2D host for oxygen vacancies, while the amorphous Al 2 O 3 facilitates the generation and stabilization of the oxygen vacancies. The conduction mechanism in the high-resistance state follows Poole–Frenkel emission, and in the the low-resistance state is fitted by the Mott–Gurney law. From the slope of the fitting curve, the mobility in the low-resistance state is estimated to be ≈2400 cm 2 V -1 s -1 , which is the highest value reported in semiconductor oxides. When annealed at high temperature to eliminate oxygen vacancies, Al is doped into the ZnO nanosheet, and the memristive behavior disappears, further confirming the oxygen vacancies as being responsible for the memristive behavior. The 2D heterointerface offers opportunities for new design of high-performance memristor devices.

2D heterostructures↗

Order-disorder behavior at thin film oxide interfaces

Order-disorder processes fundamentally determine the structure and properties of many important oxide systems for energy and computing applications. While these processes have been intensively studied in bulk materials, they are less investigated and understood for nanostructured oxides in highly non-equilibrium conditions. These systems can now be realized through a range of deposition techniques and probed at exceptional spatial and chemical resolution, leading to a greater focus on interface dynamics. In this work, we survey a selection of recent studies of order-disorder behavior at thin film oxide interfaces, with a particular emphasis on the emergence of order during synthesis and disorder in extreme irradiation environments. We summarize key trends and identify directions for future study in this growing research area.

36 MATERIALS SCIENCE↗

Field Effect Transistor Behavior in Electrospun Polyaniline/Polyethylene Oxide Nanofibers

Novel translators and logic devices based on nanotechnology concepts are under intense development. The potential for ultra-low power circuitry makes nanotechnology attractive for applications such as digital electronics and sensors. Furthermore, the ability to form devices on flexible substrates expands the range of applications where electronic circuitry can be introduced. For NASA, nonotechndogy offers opportunities for increased onboard data processing and thus autonomous decision-making ability, ad novel sensors that detect and respond to external stimuli with few oversight requirements. The goat of this work is to demonstrate transistor behavior in polyaniline/ polyethylene oxide nanofibers, thus creating a foundation for future logic devices.

Miranda, Felix A.↗

High temperature reactions of ceramics and metals with chlorine and oxygen

The reactions of chlorine and oxygen with solids are complex and quite dependent on material and reaction conditions. However, there are four reaction schemes that describe many of these reactions. These are direct reaction of chlorine with the oxide layer, penetration of the oxide layer by chlorine, paralinear behavior where oxidation and chlorination are of comparable rates, and finally, gas phase reactions where the volatile chlorides react with oxygen. Examples of chlorine and oxygen reactions with cobalt, nickel, chromium, molybdenum, and silicon carbide illustrate each of these four reaction schemes.

Jacobson, N. S.↗

Multi–length scale characterization of point defects in thermally oxidized, proton irradiated iron oxides

A key for the success of safe nuclear power generation system is to consider structural materials that are economical, meet mechanical property needs, possess good corrosion resistance, and are radiation tolerant. Nevertheless, fundamental insights that elucidate the details of radiation damage on materials corrosion performance are lacking. This includes the behavior of surface oxides which often regulate corrosion. For example, it is unclear how non-equilibrium point defects, oxide structure, mass transport in oxides, and subsequent oxidation behavior are altered by the radiation. Here, in this work, some of the effects of proton irradiation on the attributes of point defects, iron oxide microstructures, and the physical nature of the oxidation product were correlated with corrosion behavior. Iron oxides, fabricated by thermal oxidation in air at 400°C and 800°C for 1 h, were subjected to 200 keV, 0.03 dpa (displacements per atom) of proton irradiation, and subjected to corrosion reactivity assessment using AC and DC electrochemical methods. Experimental methods that target materials information at different length scales, such as positron annihilation spectroscopy (atomistic), transmission electron microscopy (mesoscopic), and electrochemical methods (macroscopic), were coupled to shed light on the impact of radiation-induced defect modifications and structural changes in oxides on corrosion reactivity which ultimately affects durability in harsh environments.

36 MATERIALS SCIENCE↗

Nickel vacancy behavior in the electrical conductance of nonstoichiometric nickel oxide film

Nickel vacancy behavior in electrical conductance is systematically investigated using various analysis methods on nickel oxide films deposited at different oxygen partial pressures. The results of Rutherford backscattering, x-ray diffraction, and Auger electron spectroscopy analyses demonstrate that the sputtered nickel oxide films are nickel-deficient. Through the deconvolution of Ni2p and O1s spectra in the x-ray photoelectron spectroscopy data, the number of Ni{sup 3+} ions is found to increase with the O{sub 2} ratio during the deposition. According to the vacancy model, nickel vacancies created from the non-stoichiometry are concluded to produce Ni{sup 3+} ions which lead to an increment of the conductivity of the nickel oxide films due to the increase of the hole concentration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Origin, nature, and the dynamic behavior of nanoscale vacancy clusters in Ni-rich layered oxide cathodes

Oxygen and transition metal (TM) vacancies in transition metal oxides (TMOs) play an important role in materials functionalities. For TMO cathodes of Li-ion batteries, vacancies can be introduced, either deliberately or inevitably, during materials synthesis or upon electrochemical cycling. Effects of vacancies on the electrochemical properties of cathodes critically depend on the dynamic characteristics of vacancies during the battery cycling. However, a fundamental understanding of such characteristics in the layer structured cathode remains elusive. Here, using scanning transmission electron microscopy (STEM), we reveal a cycling-induced aggregation behavior of oxygen and TM vacancies in a Ni-rich layer structured cathode of secondary particles. We discover that during the initial charging, vacancies aggregate to form visible vacancy-rich nanoregions (vacancy clusters) firstly at the outer layer of the secondary particle, and then the vacancy-cluster populated region extends to the inner part of particle upon fully charged. The spatial distinction of preferential nucleation of vacancy clusters at the outer layer indicates that the vacancy migration and clustering is associated with Li migration flux, which is larger at the outer layer, as all the Li from the inner part has to go through the outer layer. With extended cycling (> 50), these vacancy clusters become immobilized. We further reveal that the generation of these vacancy clusters is correlated to the material-synthesis conditions. Our findings solve a long-standing puzzle on the origin, nature, and behavior of the commonly visible vacancy clusters in the NMC cathode, providing insights on correlation between properties and dynamic behaviors of atomic-scale defects in layered oxide cathodes.

Li-ion batteries, layered oxide cathodes, NMC, cat↗

Dispersion of Nano-Sized Oxide Particles in Ni-based Alloy

High temperature materials with a good resistance to oxidation or corrosion are crucial for the Generation IV nuclear system such as VHTR (Very High Temperature Reactor). While several commercial Ni-based high temperature alloys have been among the candidate ones for the IHX (intermediate heat exchanger) or HGD (hot gas duct) of VHTR, they disclose their insufficiency for the application to the anticipated outlet temperature range such as 900 deg. C or above. Unless the operating temperature is significantly lowered and the performance of the system drops in consequence, a breakthrough in the candidate materials for the key components shall be necessary for the realization of the system. Feasibility for the oxide dispersion strengthening (ODS) of Ni-based alloys was studied by fabrication of alloy 617-base ODS alloy. Alloy 617 powders were mechanically alloyed (MA) with 0.3 wt% Y{sub 2}O{sub 3} powders of around 30 nm in diameter using a horizontal ball mill (ZoZ CM 08). After degassing and canning procedure, MA powders were hot extruded. Extruded alloy samples were tensile tested at high temperatures as well as at room temperature. Also high temperature creep rupture tests were conducted at 950 deg. C in air under 20 and 25 MPa, respectively. The behavior of oxide particles within the Ni-based alloy matrix was investigated by mechanical alloying of Ni- Cr-Fe ternary alloy powders and pure Ni powders with oxide particles, respectively. Oxide such as Y{sub 2}O{sub 3}, Cr{sub 2}O{sub 3}, HfO{sub 2}, ZrO{sub 2}, TiO{sub 2}, La{sub 2}O{sub 3} were chosen from the thermodynamic point of view as the first stable candidates from more than twenty oxides, nitrides and carbides. The behavior of oxide particle within the MA powder matrix along with the temperature was characterized by using high temperature XRD (X-ray Diffractometer) and (HR)TEM (High Resolution Transmission Electron Microscope). Creep rupture tests of the ODS alloy samples at 950 deg. C showed one order of magnitude lower creep rates than those of the corresponding alloy. (authors)

36 MATERIALS SCIENCE↗

A study of the relationship between lithium ion transport and structure and dynamic behavior in polyethylene oxide-melt/LiClO 4 battery electrolytes.

An experimental study of the canonical SPE (“solid” polymer electrolyte) for rechargeable “rocking chair” lithium/polymer batteries, viz. LiClO4 dissolved in molten poly(ethylene oxide) (PEO), was carried out under DOE grant FG02-04ER15573. In this study, an improved understanding was obtained of the relationship between lithium ion transport and polymer behavior in these SPEs. Among other applications, these sturdy temperature-tolerant and powerful light-weight batteries would be used in electric and electric-hybrid vehicles to reduce greenhouse gas emissions, to store unused electrical energy for peak demand loads and as compact, light-weight energy sources for aircraft and spacecraft. During the period of the grant, the American/Canadian partnership company “Avestor” fabricated and successfully demonstrated a telecommunications application of shoe-box sized batteries and representatives from Avestor visited our research lab at UNLV. They found our results interesting and relevant to their work and invited us to visit Avestor and present a talk about our efforts at UNLV. Unfortunately Avestor (who was scheduled to build a battery production facility in Apex, Nevada just North of Las Vegas) folded before the visit could be made. In the grant work, two well characterized PEO samples having molar masses distinctly below and distinctly above the melt entanglement molar mass were used and three laser light scattering techniques employed as the principal noninvasive methods of investigating liquid poly(ethylene oxide) (PEO)/LiClO4 SPEs. These investigations considered the effects of temperature, dissolved salt concentration and scattering wavevector on SPE behavior. Classical or “static” light scattering and the dynamic light scattering techniques of photon correlation spectroscopy (PCS) and Fabry-Perot interferometry (FPI) were used to study SPE static, low frequency and high frequency dynamic behaviors, respectively. Static measurements provided information about system structure while low frequency results provided information about slower (0.1-10s) more global behavior and high frequency results provided information about faster (~10-11s) more local behavior. In addition, viscometry, rheometry and thermal analysis provided vital complementary results. It was found that liquid PEO/lithium salt solutions for both PEO molar masses are random transient physical networks with measureable network and intra-network relaxation times using PCS and FPI. Thus novel and informative results addressing both large scale and small scale behavior were obtained. For example, the high sensitivity of liquid PEO electrolytes to the presence of presumably undesirable trace amounts of residual water and/or methanol was clearly evident in PCS measurements. In “unentangled” melts the activation energies for diffusive relaxation in liquid PEO/lithium salt electrolytes measured using PCS and the activation energies for viscous flow in these systems determined by viscometry were identical while thermal analyses detected no phase transitions for these systems. These results reinforced an earlier assumption that the liquid PEO/LiClO4 system is a liquid polymer “bimorph” (to our knowledge the first of its kind to be reported) with the network comprising one form of the polymer while the second form corresponds to that of a viscous damping liquid. At a given temperature, FPI characteristic relaxation times for local, between-chain motions were consistent with PCS results so that increases with increasing salt concentration were accompanied by increases in the elastic modulus and corresponding increases in system stiffness. Note that corresponding decreases in polymer segmental mobility are accompanied by reduced ion diffusivity. For entangled melts, PCS network relaxations were again observed and these systems were also considered to be bimorphs even though diffusion activation energies were distinctly larger than viscous flow activation energies - a difference attributed to the effects of entanglement. Moreover, SLS measurements revealed entangled melts to be “percolation gels” with a measured fractal dimension of about 2 and static correlation lengths that increased gradually from about 500 nm to about 700 nm with increasing salt concentration. Meanwhile, rheological measurements found these polymer/salt melts to behave simply as liquids. FPI measurements have not yet been made on these entangled PEO melts.

25 ENERGY STORAGE↗

Effects of Multicomponent Hydrocarbon Feed on Hydrocarbon Adsorption–Desorption and Oxidation Light-Off Behavior on a Pd/BEA Hydrocarbon Trap

A model hydrocarbon trap material consisting of palladium promoted zeolite beta on a monolith core was studied with a multicomponent hydrocarbon feed. Dodecane and ethylene adsorption, followed by temperature programmed oxidation (TPO), was used in the presence of CO in wet and dry conditions to study the impact of various species on hydrocarbon storage, oxidation, and desorption. Low temperature adsorption experiments were used to quantify hydrocarbon storage capacity, while temperature programmed desorption (TPD) and TPO studies were used to investigate both oxidation and desorption of the various hydrocarbon species. Here, the low temperature adsorption experiments suggest a moderate impact of water on dodecane uptake as dry experiments adsorbed more dodecane overall than those under wet conditions. Additionally, the presence of CO and ethylene also impaired dodecane uptake. TPD studies indicated a coupled relationship between hydrocarbon oxidation light-off and desorption. By varying the composition of the feed, specifically via the inclusion of CO or ethylene, dodecane oxidation light-off was delayed, which actually increased the overall hydrocarbon trap efficiency.

42 ENGINEERING↗

Field Effect Transistor Behavior in Electrospun Polyaniline/Polyethylene Oxide Demonstrated

Novel transistors and logic devices based on nanotechnology concepts are under intense development. The potential for ultra-low-power circuitry makes nanotechnology attractive for applications such as digital electronics and sensors. For NASA applications, nanotechnology offers tremendous opportunities for increased onboard data processing, and thus autonomous decisionmaking ability, and novel sensors that detect and respond to environmental stimuli with little oversight requirements. Polyaniline/polyethylene oxide (PANi/PEO) nanofibers are of interest because they have electrical conductivities that can be changed from insulating to metallic by varying the doping levels and conformations of the polymer chain. At the NASA Glenn Research Center, we have observed field effect transistor (FET) behavior in electrospun PANi/PEO nanofibers doped with camphorsulfonic acid. The nanofibers were deposited onto Au electrodes, which had been prepatterned onto oxidized silicon substrates. The preceding scanning electron image shows the device used in the transistor measurements. Saturation channel currents are observed at surprisingly low source/drain voltages (see the following graph). The hole mobility in the depletion regime is 1.4x10(exp -4)sq cm/V sec, whereas the one-dimensional charge density (at zero gate bias) is calculated to be approximately 1 hole per 50 two-ring repeat units of polyaniline, consistent with the rather high channel conductivity (approx.10(exp -3) S/cm). Reducing or eliminating the PEO content in the fiber is expected to enhance device parameters. Electrospinning is thus proposed as a simple method of fabricating one-dimensional polymer FET's.

Mueller, Carl H.↗