Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Numerical optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Traffic Flow Management Using Aggregate Flow Models and the Development of Disaggregation Methods

A linear time-varying aggregate traffic flow model can be used to develop Traffic Flow Management (tfm) strategies based on optimization algorithms. However, there are no methods available in the literature to translate these aggregate solutions into actions involving individual aircraft. This paper describes and implements a computationally efficient disaggregation algorithm, which converts an aggregate (flow-based) solution to a flight-specific control action. Numerical results generated by the optimization method and the disaggregation algorithm are presented and illustrated by applying them to generate TFM schedules for a typical day in the U.S. National Airspace System. The results show that the disaggregation algorithm generates control actions for individual flights while keeping the air traffic behavior very close to the optimal solution.

Sun, Dengfeng↗

The Influences of Lamination Angles on the Interior Noise Levels of an Aircraft

The feasibility of reducing the interior noise levels of an aircraft passenger cabin through optimization of the composite lay up of the fuselage is investigated. MSC/NASTRAN, a commercially available finite element code, is used to perform the dynamic analysis and subsequent optimization of the fuselage. The numerical calculation of sensitivity of acoustic pressure to lamination angle is verified using a simple thin, cylindrical shell with point force excitations as noise sources. The thin shell used represents a geometry similar to the fuselage and analytic solutions are available for the cylindrical thin shell equations of motion. Optimization of lamination angle for the reduction of interior noise is performed using a finite element model of an actual aircraft fuselage. The aircraft modeled for this study is the Beech Starship. Point forces simulate the structure borne noise produced by the engines and are applied to the fuselage at the wing mounting locations. These forces are the noise source for the optimization problem. The acoustic pressure response is reduced at a number of points in the fuselage and over a number of frequencies. The objective function is minimized with the constraint that it be larger than the maximum sound pressure level at the response points in the passenger cabin for all excitation frequencies in the range of interest. Results from the study of the fuselage model indicate that a reduction in interior noise levels is possible over a finite frequency range through optimal configuration of the lamination angles in the fuselage. Noise reductions of roughly 4 dB were attained. For frequencies outside the optimization range, the acoustic pressure response may increase after optimization. The effects of changing lamination angle on the overall structural integrity of the airframe are not considered in this study.

Fernholz, Christian M.↗

Best-Fit Conic Approximation of Spacecraft Trajectory

A computer program calculates a best conic fit of a given spacecraft trajectory. Spacecraft trajectories are often propagated as conics onboard. The conic-section parameters as a result of the best-conic-fit are uplinked to computers aboard the spacecraft for use in updating predictions of the spacecraft trajectory for operational purposes. In the initial application for which this program was written, there is a requirement to fit a single conic section (necessitated by onboard memory constraints) accurate within 200 microradians to a sequence of positions measured over a 4.7-hour interval. The present program supplants a prior one that could not cover the interval with fewer than four successive conic sections. The present program is based on formulating the best-fit conic problem as a parameter-optimization problem and solving the problem numerically, on the ground, by use of a modified steepest-descent algorithm. For the purpose of this algorithm, optimization is defined as minimization of the maximum directional propagation error across the fit interval. In the specific initial application, the program generates a single 4.7-hour conic, the directional propagation of which is accurate to within 34 microradians easily exceeding the mission constraints by a wide margin.

Singh, Gurkipal↗

Hybrid NN/SVM Computational System for Optimizing Designs

A computational method and system based on a hybrid of an artificial neural network (NN) and a support vector machine (SVM) (see figure) has been conceived as a means of maximizing or minimizing an objective function, optionally subject to one or more constraints. Such maximization or minimization could be performed, for example, to optimize solve a data-regression or data-classification problem or to optimize a design associated with a response function. A response function can be considered as a subset of a response surface, which is a surface in a vector space of design and performance parameters. A typical example of a design problem that the method and system can be used to solve is that of an airfoil, for which a response function could be the spatial distribution of pressure over the airfoil. In this example, the response surface would describe the pressure distribution as a function of the operating conditions and the geometric parameters of the airfoil. The use of NNs to analyze physical objects in order to optimize their responses under specified physical conditions is well known. NN analysis is suitable for multidimensional interpolation of data that lack structure and enables the representation and optimization of a succession of numerical solutions of increasing complexity or increasing fidelity to the real world. NN analysis is especially useful in helping to satisfy multiple design objectives. Feedforward NNs can be used to make estimates based on nonlinear mathematical models. One difficulty associated with use of a feedforward NN arises from the need for nonlinear optimization to determine connection weights among input, intermediate, and output variables. It can be very expensive to train an NN in cases in which it is necessary to model large amounts of information. Less widely known (in comparison with NNs) are support vector machines (SVMs), which were originally applied in statistical learning theory. In terms that are necessarily oversimplified to fit the scope of this article, an SVM can be characterized as an algorithm that (1) effects a nonlinear mapping of input vectors into a higher-dimensional feature space and (2) involves a dual formulation of governing equations and constraints. One advantageous feature of the SVM approach is that an objective function (which one seeks to minimize to obtain coefficients that define an SVM mathematical model) is convex, so that unlike in the cases of many NN models, any local minimum of an SVM model is also a global minimum.

Rai, Man Mohan↗

Optimal design of structures with buckling constraints.

The paper presents an iterative, finite element method for minimum weight design of structures with respect to buckling constraints. The redesign equation is derived from the optimality criterion, as opposed to a numerical search procedure, and can handle problems that are characterized by the existence of two fundamental buckling modes at the optimal design. Application of the method is illustrated by beam and orthogonal frame design problems.

Kiusalaas, J.↗

Uncertainty Aware Structural Topology Optimization Via a Stochastic Reduced Order Model Approach

This work presents a stochastic reduced order modeling strategy for the quantification and propagation of uncertainties in topology optimization. Uncertainty aware optimization problems can be computationally complex due to the substantial number of model evaluations that are necessary to accurately quantify and propagate uncertainties. This computational complexity is greatly magnified if a high-fidelity, physics-based numerical model is used for the topology optimization calculations. Stochastic reduced order model (SROM) methods are applied here to effectively 1) alleviate the prohibitive computational cost associated with an uncertainty aware topology optimization problem; and 2) quantify and propagate the inherent uncertainties due to design imperfections. A generic SROM framework that transforms the uncertainty aware, stochastic topology optimization problem into a deterministic optimization problem that relies only on independent calls to a deterministic numerical model is presented. This approach facilitates the use of existing optimization and modeling tools to accurately solve the uncertainty aware topology optimization problems in a fraction of the computational demand required by Monte Carlo methods. Finally, an example in structural topology optimization is presented to demonstrate the effectiveness of the proposed uncertainty aware structural topology optimization approach.

Aguilo, Miguel A.↗

Power Optimization of Cryogenic CO2 Deposition Capture in Deep Space

An extremely reliable cabin air revitalization system is needed for human deep space exploration missions. Deep space offers an environmental temperature close to 4 Kelvin. This low environmental temperature enables heat rejection for systems that are thermally power-intensive, i.e. CO2 cold surface deposition (CDep). The CDep system relies on phase change temperatures of air components to deposit CO2 onto a cold surface. The cold surface can be generated utilizing cryocoolers, including Stirling and Reverse Brayton, or deep space environmental temperature. This paper presents a numerical study on a power optimization of cold surface generation via a cryocooler or thermal radiator. An example system for each type is presented. However, a hybrid system would not only reduce power required to remove CO2, but also increase redundancy and reliability of the air revitalization system.

Pranav Jagtap↗

A hybrid nonlinear programming method for design optimization

Solutions to engineering design problems formulated as nonlinear programming (NLP) problems usually require the use of more than one optimization technique. Moreover, the interaction between the user (analysis/synthesis) program and the NLP system can lead to interface, scaling, or convergence problems. An NLP solution system is presented that seeks to solve these problems by providing a programming system to ease the user-system interface. A simple set of rules is used to select an optimization technique or to switch from one technique to another in an attempt to detect, diagnose, and solve some potential problems. Numerical examples involving finite element based optimal design of space trusses and rotor bearing systems are used to illustrate the applicability of the proposed methodology.

Rajan, S. D.↗

Numerical Investigation of Roughness Effects on Transition on Spherical Capsules

The state of the boundary layer on space re-entry vehicles significantly affects the design of the thermal protection system. However, the physical mechanism that leads to the laminar-turbulent boundary-layer transition on blunt spherical capsules remains an open question in literature. This work numerically assesses the potential of roughness-induced non-modal disturbance growth on re-entry capsules with a spherical-section forebody by optimal transient-growth theory and direct numerical simulation. Two different sets of wind-tunnel experiments are considered. Optimal transient-growth studies have been performed for the blunt capsule experiments at Mach 5.9 in the Hypersonic Ludwieg tube Braunschweig (HLB) of the Technische Universitat Braunschweig. In some of these measurements, the capsule model was equipped with a specifically designed patch of distributed micron-sized surface roughness. The transient-growth results for the HLB capsule are compared to corresponding numerical data for a Mach 6 blunt capsule experiment in the Adjustable Contour Expansion (ACE) facility of the Texas A&M University (TAMU) at lower Reynolds number. Similar trends are observed for both configurations. In particular, a rather low maximum energy gain is noted for the surface temperature conditions of the experiments. It is shown that the surface temperature dependence of the optimal transient-growth results is very similar for both capsule configurations. Moreover, the generation of stationary disturbances by well-defined roughness patches on the capsule surface is studied for the conditions of the HLB experiment using direct numerical simulations (DNS). To help explain the observed laminar-turbulent transition downstream of the roughness patch in some of the HLB capsule experiments, additional simulations were carried out to study the evolution of unsteady perturbations within the steady disturbance flow field due to the roughness patch. However, the DNS did not provide any indication of modal or non-modal disturbance growth in the wake of the roughness patch, and hence, the physical mechanism underlying the observed onset of transition remains unknown.

Hein, Stefan↗

Optimal output fast feedback in two-time scale control of flexible arms

Control of lightweight flexible arms moving along predefined paths can be successfully synthesized on the basis of a two-time scale approach. A model following control can be designed for the reduced order slow subsystem. The fast subsystem is a linear system in which the slow variables act as parameters. The flexible fast variables which model the deflections of the arm along the trajectory can be sensed through strain gage measurements. For full state feedback design the derivatives of the deflections need to be estimated. The main contribution of this work is the design of an output feedback controller which includes a fixed order dynamic compensator, based on a recent convergent numerical algorithm for calculating LQ optimal gains. The design procedure is tested by means of simulation results for the one link flexible arm prototype in the laboratory.

Siciliano, B.↗

A trajectory planning scheme for spacecraft in the space station environment

Simulated annealing is used to solve a minimum fuel trajectory problem in the space station environment. The environment is special because the space station will define a multivehicle environment in space. The optimization surface is a complex nonlinear function of the initial conditions of the chase and target crafts. Small permutations in the input conditions can result in abrupt changes to the optimization surface. Since no prior knowledge about the number or location of local minima on the surface is available, the optimization must be capable of functioning on a multimodal surface. It was reported in the literature that the simulated annealing algorithm is more effective on such surfaces than descent techniques using random starting points. The simulated annealing optimization was found to be capable of identifying a minimum fuel, two-burn trajectory subject to four constraints which are integrated into the optimization using a barrier method. The computations required to solve the optimization are fast enough that missions could be planned on board the space station. Potential applications for on board planning of missions are numerous. Future research topics may include optimal planning of multi-waypoint maneuvers using a knowledge base to guide the optimization, and a study aimed at developing robust annealing schedules for potential on board missions.

Soller, Jeffrey Alan↗

Numerical and classical analysis of V/STOL aircraft using selected propulsion systems

The development needed for the evolution of selected V/STOL research vehicles into optimized antisubmarine warfare (ASW) aircraft configurations, using numerical procedures and traditional analytical methods, has been examined. Three propulsion systems, which represent state-of-the-art development aimed at solving the thrust-vectoring and attitude-control problems of V/STOL aircraft, are analyzed. The use of NASA computer programs for aircraft synthesis (ACSYNT), and for optimizing configurations (COMMIN), coupled with contractor-supplied propulsion system data provides for accurate performance prediction of the selected ASW configurations. Particular emphasis on the transition phase between the research vehicle and the optimized configuration demonstrates the strengths and weaknesses of using generic research aircraft instead of building prototypes to demonstrate new technology

Wilson, S. B., III↗

Bi-Level Integrated System Synthesis (BLISS) for Concurrent and Distributed Processing

The paper introduces a new version of the Bi-Level Integrated System Synthesis (BLISS) methods intended for optimization of engineering systems conducted by distributed specialty groups working concurrently and using a multiprocessor computing environment. The method decomposes the overall optimization task into subtasks associated with disciplines or subsystems where the local design variables are numerous and a single, system-level optimization whose design variables are relatively few. The subtasks are fully autonomous as to their inner operations and decision making. Their purpose is to eliminate the local design variables and generate a wide spectrum of feasible designs whose behavior is represented by Response Surfaces to be accessed by a system-level optimization. It is shown that, if the problem is convex, the solution of the decomposed problem is the same as that obtained without decomposition. A simplified example of an aircraft design shows the method working as intended. The paper includes a discussion of the method merits and demerits and recommendations for further research.

Sobieszczanski-Sobieski, Jaroslaw↗

Structural tailoring/analysis for hypersonic components - Executive system development

No direct analytical or integrated numerical tool exists today for the optimal design of a generic class of built-up actively cooled composite structure for applications in hypersonic propulsion ducts. The need exists for a numerical tool to perform the comprehensive design/analysis of a panel on the inlet wall under hypersonic flight conditions. Such a tool requires relatively complex multi-disciplinary analysis. One such numerical tool controlled by an executive system has been developed and is named as STAHYC (Structural Tailoring/Analysis for HYpersonic Components). A detailed account of the executive system development of STAHYC along with the results of one example inlet panel design problem is given in this paper.

Narayanan, G. V.↗

Numerical model for the Programmable Multirole Furnace (PMZF)

The present account of the Programmable Multizone Furnace numerical model uses various examples to illustrate the ways in which the model serves as an optimization, test, prediction, and visualization tool; a numerical PID-control algorithm obtains the desired sample temperature distributions and allows the model to solve an inverse heat transfer problem where the desired sample temperature profile is the input and the required heater power distribution is the output of numerical simulations. Parametric studies show how the total power consumption of the furnace is affected by such design variables as the conductivity.

Kassemi, M.↗

Characteristics of the boundary-layer equations of the minimum time-to-climb problem

In many singular perturbation solutions of optimal control problems, the most difficult numerical task is to solve the boundary-layer equations. However, these equations have a special structure that may often be used to expedite their solution. This paper begins by noting the general nature of the boundary-layer equations for optimal control problems. These results are then applied to the aircraft minimum time-to-climb problem. A specific numerical example is considered to illustrate the characteristics of the solution of the boundary-layer equations for this problem.

Ardema, M. D.↗

A Numerical Comparison of Barrier and Modified Barrier Methods for Large-Scale Bound-Constrained Optimization

When a classical barrier method is applied to the solution of a nonlinear programming problem with inequality constraints, the Hessian matrix of the barrier function becomes increasingly ill-conditioned as the solution is approached. As a result, it may be desirable to consider alternative numerical algorithms. We compare the performance of two methods motivated by barrier functions. The first is a stabilized form of the classical barrier method, where a numerically stable approximation to the Newton direction is used when the barrier parameter is small. The second is a modified barrier method where a barrier function is applied to a shifted form of the problem, and the resulting barrier terms are scaled by estimates of the optimal Lagrange multipliers. The condition number of the Hessian matrix of the resulting modified barrier function remains bounded as the solution to the constrained optimization problem is approached. Both of these techniques can be used in the context of a truncated-Newton method, and hence can be applied to large problems, as well as on parallel computers. In this paper, both techniques are applied to problems with bound constraints and we compare their practical behavior.

Nash, Stephen G.↗

Numerical solutions of a control problem governed by functional differential equations

A numerical procedure is proposed for solving optimal control problems governed by linear retarded functional differential equations. The procedure is based on the idea of 'averaging approximations', due to Banks and Burns (1975). For illustration, numerical results generated on an IBM 370/158 computer, which demonstrate the rapid convergence of the method are presented.

Banks, H. T.↗