Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material test reactors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Gear Test Assembly - Experimental Testing and Analysis of Gears and Bearings - FY2026

The Gear Test Assembly (GTA) is an experimental test apparatus built and installed in the Mechanisms and Engineering Test Loop (METL) at Argonne National Laboratory (ANL). While designed to accommodate a variety of components intended for use in advanced compact in-vessel transfer machine, the focus of GTA been the testing of large radial spur gears. The performance of the components used in GTA motivates the choices made in the design, components, and material choices for the forthcoming METL test articles; the Gripper Test Assembly (GrTA), and the Bearing Test Assembly (BTA). To date, GTA has completed nine experimental testing campaigns and achieved over 21 million revolutions under prototypic sodium fast reactor loads and operating conditions. This report provides an overview and results for the two most recent experiments Campaign #8 and Campaign #9. `Campaign #8 was the first campaign to make use of a set of nickel alloy radial spur gears, made from Hastelloy C-22HS, and combined with heat-treated tapered roller bearings. The bearings and torque profile used allowed Campaign #8 to be directly compared with Campaign #1 where Inconel 718 gears were used instead. Campaign #8 attained 1,058,880 shaft revolutions within 23% of the 1,314,855 revolutions achieved in Campaign #1. These results demonstrate that the heat-treated tapered roller bearings show consistent increased lifetimes, approximately three times longer than for non heat-treated taper rollers, and that the particular material of the gear does not play a substantial role in performance. Similar to Campaign #7 where bearing failure resulted in fragmentation and transport of bearing material into the gear teeth led to tooth damage in the Inconel gears, a similar process led to the damage of the Hastelloy gears. Subsequent NDE analysis showed that the damage was only limited to the tooth surface and does not extend into the gear interiors. Based on the NDE reports, the Hastelloy gears can be reconditioned and put back into service for future campaigns as was done for the Inconel gears. Reconditioned Inconel 718 gears damaged in Campaign #7 were returned to service in Campaign #9 and paired with non heat-treated tapered roller bearings. In Campaign #9 a novel set of operating conditions were implemented whereby the gears and bearings were cycled between hot, submerged refueling conditions where fuel handling operations occurred and cold, dry, and inert conditions where the sodium was drained and the vessel was allowed to cool simulating long, ex-vessel storage of the fuel handling machine. A total of eight of these operating cycles were achieved before a bearing failure occurred after the accumulation of 475,692 shaft revolutions were achieved. During Campaign #9, one of the drive motors was damaged and over the course of a 240 day standby period, the entire GTA drive system was upgraded from a 480VAC system to a 240VAC system that provided the opportunity to consolidate wall-space in the METL facility and provide more space for additional test articles being installed in the coming year. The over 475,000 shaft revolutions achieved in Campaign #9 eclipses the previous record for lifetime of non heat-treated tapered roller bearings held by Campaign #3 of 392,000 shaft revolutions. Further analysis and future campaigns hope to shed light on the cause of this approximately 17% increase in lifetime.

42 ENGINEERING↗
DOE OSTI2025

AGR TRISO Fuel Performance Modeling in FY-25

This report summarizes the activities performed in FY-25 to support fuel performance modeling for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. This includes implementation of a new uranium oxycarbide (UCO) kernel swelling rate model, inner pyrolytic carbon (IPyC) cracking behavior and failure predictions, development of new UCO and silicon carbide (SiC) cesium diffusion parameters, and the thermomechanical behavior of particle layers using experimental data from micro-tensile strength testing.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Radioactive Waste Sludge Washing and Demonstration of the Nitric-Glycolic Acid Flowsheet for Sludge Batch 10 Qualification

For each sludge batch that is processed in the Defense Waste Processing Facility (DWPF), the Savannah River National Laboratory (SRNL) performs qualification testing to demonstrate that the sludge batch (SB) is processible. During processing of SB9, DWPF will be transitioning from the Nitric-Formic Acid (NFA) flowsheet to the Nitric-Glycolic Acid (NGA) flowsheet. Thus, the qualification of SB10 was requested to only be performed using the NGA flowsheet. In order to qualify the batch for the NGA flowsheet, Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) cycles, designated SC-19, were performed using SB10 Tank 51 sample material. SRNL received Tank 51 material in the midst of Tank Farm washing. SRNL continued the washing in the SRNL Shielded Cells. The SRNL process included the addition of Sodium Reactor Experiment (SRE) material from H Canyon, simulating the transfer of SRE from H Canyon to Tank 51 during Tank Farm washing. The washed SB10 Tank 51 material, with SRE, was characterized prior to flowsheet qualification testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

HIGH BURNUP FUEL-COOLANT INTERACTION ANALYSIS SUPPORTING FUEL SAFETY TESTING AT IDAHO NATIONAL LABORATORY

In the near future, experiments on HBu fuel under loss-of-coolant accident (LOCA) and reactivity-initiated accident (RIA) conditions will be performed within the Transient Reactor Test Facility (TREAT) at Idaho National Laboratory (INL). These experiments will be performed using the Transient Water Irradiation System for TREAT (TWIST) experiment vehicle. To support these experiments, analysis of fuel-coolant interaction (FCI) energetics is underway. This paper discusses FCIs in the context of light water reactor (LWR) safety, differentiating between the severe accident focus of commercial reactors and experimental RIA test programs where FCIs have occurred. However, it is highlighted that as the nuclear industry aims for increased burnup limits, the FCI events observed in RIA test programs may become relevant to commercial LWR safety analysis. The paper then presents developments to the UW-FCI computer program to enable simulation of FCIs initiated by solid fuel particles dispersing into the coolant during RIAs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Understanding FLiNaK Salt Intrusion Behavior on Nuclear-Grade Graphite via Neutron Tomography

Graphite is an essential material as a neutron moderator in molten salt reactors (MSRs). To understand the impact of salt on the graphite structure to develop structural materials for MSRs, molten salt intrusion behavior on nuclear-grade graphite was studied. The graphite samples, IG-110 and PCEA, were tested for infiltration with LiF-NaF-KF (FLiNaK) at 750°C, 5 bar for 12 h, and, after the intrusion experiment, the graphite was analyzed by neutron imaging. The graphite and Li from FLiNaK showed great contrast in the neutron attenuation coefficient. Thus, the salt behavior in the graphite structure has been visualized for the first time without damaging the sample. The 3D image of the graphite was reconstructed after a neutron computed tomography scan, and the average salt coverage distribution of the XY surface in different depths was obtained from the reconstructed 3D images.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

ASME Code change proposal to implement new universal high temperature constitutive models for Section III, Division 5

This report completes work on a universal high temperature constitutive model suitable for use with the ASME Boiler & Pressure Vessel Code Section III, Division 5 rules for the design by inelastic analysis of Class A nuclear reactor components. The goals of this work are to provide a simple model form that adequately captures the high temperature response of materials and can be applied to any future Code material. Additionally, the report describes an automated process for calibrating a model against test data. The idea is to simplify the effort required to generate a constitutive model for an arbitrary material, provided test data is available. This will accelerate the process of qualifying new Code materials in the future. In addition, the report provides calibrated models and detailed validation comparisons to test data for five currently-qualified or soon-to-be qualified materials: 316H, Grade 91, Alloy 800H, Alloy 617, and Alloy 709. The report surveys the available data for the remaining two ASME Class Materials --- 2.25Cr-1Mo and 304H --- concluding that there is enough data data to generate a model for 2.25Cr-1Mo steel provided some additional sources of non-public data can be included in the test database, but that a dedicated cyclic test campaign would be needed for 304H. Supplemental material includes the full text of an ASME Code change proposal to incorporate the models for the four currently-qualified Class A material, detailed validation comparisons to test data for the five material models, and input files for reference implementations of the constitutive models in the NEML and NEML2 modeling frameworks.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Sensitivity Analysis of Irradiated Fueled Experiments using the MOOSE Framework [Slides]

Modeling and simulation (M&S) methods are able to predict uncertainties in experimental parameters (e.g., power and fission density) during irradiation. A shortfall exists in predicting how sensitive some of the parameters will behave during the experimental process. Sensitivity and Uncertainty Quantification (SUQ) is critical in support of qualification and licensing reactor fuels. The application of a method to quantify the uncertainty in these experiments is critical to the prediction of their performance. In this work, we propose the use of a polynomial chaos expansion (PCE) method to quantify the sensitive parameters in these simulations and, in an extension, their experimental surrogates. We propose to perform M&S using PCE uncertainty quantification on a previously irradiated fueled experiment in order to provide a validation case for Griffin and expand its use as a verification and validation (V&V) tool for experiments with a neutronics component. Griffin is an advanced, deterministic neutronics analysis code built using the MOOSE (multiphysics object-oriented simulation environment) framework which can provide state-of-the-art neutronic analysis on M&S of experiments. We will use the stochastic tools module (STM) in MOOSE to provide PCE uncertainty quantification on the proposed experimental setup. Idaho National Laboratory (INL) does not yet have an in-house developed code with V&V approval for experiments performed on-site; this work would provide a necessary addition of support for experiments performed at INL. The Nuclear Regulatory Commission (NRC) has explicitly requested uncertainties in calculated values such as fuel power and burnup, and the development of this capability would benefit the relationship between INL and the NRC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Investigation of Polyurethane and Fire-Retardant Foams as a Radiological Contamination Fixatives - 20202

Fixation of radiological contamination in decommissioning and deactivation can reduce worker risk, and mitigate potentially hazardous conditions; however, nearly every marketed contamination fixative has been found to be flammable, a significant concern in radiological facilities. Coupled with this, industry fixatives are normally used as a thin coating which can present problems when attempting to stabilize irregular void spaces or areas that are difficult to access and ensure full coverage. To this end, Savannah River National Laboratory (SRNL), in conjunction with Florida International University (FIU), have begun investigating the applicability of polyurethane based foaming materials, which will expand to fill a given asymmetric volume and provide fire retardancy to ensure no release of contamination in the event of a facility fire. Commercial foams undergo exothermic reactions resulting in gaseous release that subsequently causes the curing foam material to expand. Heat generation during curing can potentially compromise rubber parts of an enclosure, a significant concern in nuclear facilities. To mitigate large body heat generation, SRNL has also examined multiple layering of the material to ensure compatibility of the curing material with a previously cured body of the same material. Environmental studies were also completed in order to determine the influence on polyurethane based foams curing process. These studies showed that nearly half of the materials tested delaminated from a cured body of the same material, a property not discussed in commercially available documentation on the products. Of note was the compatibility of the foaming material with the substrate, depending on the type material that the foam was cured in/on, significant delamination could occur. Mechanical testing via tensile pull tester, dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA) was also performed. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Design and testing of an enriched uranium fueled molten salt irradiation vehicle

Molten salt reactors (MSRs) have garnered increasing attention recently with several demonstration efforts on the way. A key challenge to the licensing basis for these reactors is the lack of experimental data on fueled salts. This is expected to be crucial to the safety evaluation and licensing basis of reactors of this type deployed in the future. While capability for irradiating molten salts has started being reestablished in the recent decade, no enriched fuel irradiation capability has been developed and tested as of yet. A new experiment vehicle under development at Idaho National Laboratory (INL) is presented here. The Molten-salt Research Temperature-controlled Irradiation (MRTI) experiment was developed to host enriched-uranium bearing salt samples to be irradiated at a test reactor within the lab complex. One of the key scientific objectives is to provide irradiated salt samples for post irradiation examination (PIE) to study the impact of fission product generation and neutron/gamma radioactivity on the salt solution and salt-facing wall material. This paper provides a detailed overview of the mechanical design of the experiment, followed by an overview of the fabrication and assembly of an initial prototype vehicle (with non-fuel bearing salt). A summary of the key analyses conducted as a part of the performance and safety evaluation is then provided. Lastly, an overview of the test conducted in prototypic out-of-pile (non-neutron) environment are shown. These evaluations provide the foundation for a planned irradiation of and enriched uranium-bearing chloride salt sample in the near term. The upcoming irradiation will contain 13cm 3 of UCl 3 -NaCl salt (93% enrichment) generating around 20 W/cm 3 of fission energy during irradiation and a temperature range that can be contained between bounds of 525-900°C.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Development of Innovative Non-Concentrated Alloy (NCA) Fuel Cladding for Advanced Nuclear Reactors

As the nuclear energy sector advances toward next-generation reactors, the need for high-performance fuel cladding materials has become increasingly urgent. Traditional alloys like zirconium and stainless steel are reaching their performance limits under higher temperatures, more corrosive coolants, and extended irradiation. This report presents the development of a new class of fuel cladding materials based on Non-Concentrated Alloys (NCAs) ? multi-element systems designed to deliver enhanced mechanical strength, corrosion resistance, and radiation tolerance. Through a combination of computational modeling (Computer Coupling of Phase Diagrams and Thermochemistry: CALPHAD), simulation-guided alloy selection, and experimental fabrication via arc melting and spark plasma sintering (SPS), three strategic alloy design paths were explored: (1) FeCrAl-based NCAs, (2) refractory-lean neutron-efficient alloys, and (3) equimolar high-entropy compositions. Microstructural analysis confirmed the formation of stable body-centered cubic BCC_A2 phases, while mechanical testing demonstrated hardness values significantly exceeding those of conventional cladding materials. The results highlight the tunability of NCA systems and their potential for balancing strength and ductility ? a critical consideration for in-reactor performance. Looking forward, future work will focus on thermomechanical optimization, CALPHAD refinement, and benchmarking against industry standards to enable scalable deployment. This work not only advances the science of nuclear materials but also supports broader goals in nuclear safety, performance, and nuclear energy innovation.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

A Summary of the Microstructural Characterization Results for the A709 Commercial Heats

To improve high temperature strength for advanced nuclear reactors, it is necessary to qualify additional structural materials for introduction into the American Society of Mechanical Engineers (AMSE) Boiler and Pressure Vessel Code (BPVC). Specifically, Alloy 709 was identified as a material for Sodium-cooled Fast Reactors to enhance time-dependent mechanical properties compared to 316H stainless steel, a code qualified high temperature alloy. Idaho National Laboratory (INL) and Oak Ridge National Laboratory (ORNL) performed initial microstructure and mechanical property testing on a third, commercial heat of Alloy 709 stainless steel. The Alloy 709 plate was produced by Allegheny Technology Inc. (ATI) and in the solution annealed condition. The chemical composition was within the limits for an American Society of Testing and Materials (ASTM) A213 specification for seamless tube for material UNS S31025. Grain size was measured as an average ASTM size of 6.5, which was larger than the ASTM 7 required according to ASTM A213 for seamless tube. The chemical composition was within the limits for an ASTM A213, and the room temperature tensile tests and hardness data met ASTM A213 specifications. Creep-fatigue results showed similar behavior to previous heats of Alloy 709.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Embedding Sensors in 3D Printed Metal Structures

The Transformational Challenge Reactor (TCR) program is leveraging recent advances in modeling and simulation, materials, and additive manufacturing (AM) technologies to design a modern nuclear reactor. Some of the main TCR technologies include in situ monitoring and the integration of sensors during the manufacturing of quality-significant nuclear reactor components. This report describes the general procedure and process optimization for embedding sensors within generic stainless steel 316 (SS316) components using laser powder bed fusion (LPBF). A more detailed, quality-significant test plan and supporting procedures are available upon request (ORNL/TM-2021/2127). LPBF involves the use of a scanning laser to selectively melt regions of a powder bed, additively building a part layer by layer. This report describes the LPBF processing technique and discusses the effects of LPBF processing parameters on the success of the sensor embedding process. Experiments used machined cavities in the form of channels in an SS316 base for the sensors to lay in while material is additively built over the top, thereby embedding them in an SS316 matrix. A preliminary investigation involved using empty SS316 sheaths as surrogates to explore the effects of various LPBF processing parameters and the dimensional requirements of the machined channels. Microstructural investigations showed that a smaller channel width/depth combination closer to the sensor’s diameter was best for the embedding process. After the desired parameters were selected, Type-K thermocouples were embedded and evaluated post-embedding using nondestructive thermal testing, as well as destructive sectioning and microscopy. Post-build characterization showed that the thermocouples were well-bonded to the SS316 matrix and were fully functional after embedding. During thermal testing to temperatures up to 500 °C, the embedded thermocouples read consistently with one another and deviated only slightly from the readings of a nonembedded thermocouple located within the furnace. This slight discrepancy was most likely due to differences in the thermal time constants for a nonembedded thermocouple vs. a thermocouple embedded in a solid SS316 block. The results presented in this report will serve as the foundation for future work that will focus on embedding sensors in relevant TCR reactor components and eventually testing those components under neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Neutronic Consideration of TREAT Facility Fuel SiC Recladding

The Transient Reactor Test (TREAT) Facility is an air-cooled reactor composed of graphite-urania fuel encapsulated in zirconium alloy canisters and surrounded by ~2 ft (~61 cm) of nuclear grade graphite. The primary role of TREAT is to provide in-pile nuclear-heated safety research via transient testing [1]. Benchmark efforts have demonstrated sensitivity of TREAT neutronics models to graphite cross section data and key neutron poisons found in the fuel assemblies [2]. During fabrication of TREAT fuel assemblies, a small concentration of boron was inadvertently introduced with variable concentration into the aggregate of fuel blocks prepared for TREAT use. The concentration of boron, and its respective uncertainty, represent the most sensitive component in a neutronics study; unfortunately, nothing can be done to reduce or otherwise mitigate its impact. Hydrogen in the fuel blocks reduces the mean free path of the core and its true quantity and uncertainty is approximated. The hydrogen remains from pitch binder used in the fuel fabrication process and was not completely released due to incomplete fuel graphitization. Destructive fuel testing is necessary to quantify the actual hydrogen content and to improve benchmark model quality. A third neutron poison of some significance is the hafnium impurity in the Zircaloy-3 (Zry-3) assembly cladding. The quantity of hafnium is expected to be within nominal manufacturing limits for nuclear grade zircaloy. Recladding the fuel assemblies with material that is less neutron absorbing is expected to benefit reactor neutron economy. Moreover, TREAT’s total transient energy is restricted based on the rate of Zry-3 oxidation in TREAT’s air coolant environment. Hence, cladding with more benign air reaction kinetics could dramatically uprate the facility’s experimental capability. Silicon carbide (SiC) has been proposed as a candidate material for recladding TREAT assemblies, as SiC/SiC demonstrate favorable properties within nuclear environments [3]. The current operational limits of TREAT are restricted by the oxidation of Zry-3. Change of the cladding to SiC could feasibly double the current temperature limitation. Recladding opportunities allow for previously damaged fuel assemblies to be returned to service, as Zry-3 is not commercially available. The initial effort required to consider proceeding with any recladding effort is to neutronically characterize key reactor parameters while replacing Zry-3 with SiC. A characterization summary, with respective results, is provided herein.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

MEITNER Resource Team Modeling and Simulation Support to Holos-Quad Reactor Development (Final CRADA Report)

The main objective of this CRADA is to provide Argonne National Laboratory (ANL)’s modeling and simulation capabilities via ARPA-E's MEITNER (Modeling-Enhanced Innovations Trailblazing Nuclear Energy Reinvigoration) Resource Team (RT) arrangement to support the demonstration of the viability of HolosGen’s Holos-Quad reactor design. The Holos-Quad reactor design is an advanced reactor concept that incorporates many new design features, such as the neutron-coupled Subcritical Power Modules (SPMs) in its core design, elimination of balance of plant (BOP) by direct integration of a helium Brayton cycle power conversion system with each SPM, among many other innovative features. The demonstration of the viability of such an innovative reactor design warrants iterations of modeling and simulation and testing. The purpose of this project is to utilize ANL’s modeling and simulation capabilities in nuclear reactor analysis and power conversion system analysis to inform HolosGen and the Design Team (DT) in the design and optimization of the Holos-Quad concept. The major work scopes of this project include: to investigate conceptual designs and materials for radiation shielding to protect personnel and internal components such as turbomachinery; Assess the the helium Brayton cycle power conversion system performance in both nominal and load following conditions; Investigate power conversion components and overall system performance; Identify control strategies to enable load following; Perform simulations of HolosGen’s subscale simulator and using available test data for code validation/benchmark purpose; Perform core thermal-hydraulics, safety analysis, and structural analysis.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Mechanical Properties and Deformation Behavior of Additively Manufactured 316L Stainless Steel (FY2020)

The Transformational Challenge Reactor (TCR) program plans to build most of the TCR core components through additive manufacturing (AM) processes. These processes include laser powder bed fusion (LPBF) for the metallic (316L) components and the newly developed combined process of binderjet printing and chemical vapor infiltration (CVI) for the SiC fuel matrix. Mechanical testing and characterization tasks have been carried out since the beginning of the TCR program to (1) build a property database for the AM materials that will be used in TCR core and (2) to assess the materials’ performance in TCR-relevant conditions. This document reports the outcome of the testing and characterization efforts for the fiscal year with a focus on the mechanical performance data of AM 316L stainless steel (SS). Baseline tensile testing over a wide temperature range of room temperature–600 °C was completed for the AM 316L alloy in as-built, stress-relieved, and solution-annealed conditions. The as-built 316L showed the highest strength, and the alloy after the post-build treatments showed reduced strengths in the low-strain range. However, the strength differences among the AM materials became insignificant in the later part of deformation. Furthermore, regardless of post-build processing, the AM 316L SS showed higher strength and comparable ductility when compared with wrought 316L SS. Thermal creep testing and microstructural evolution during creep deformation were also performed under selected conditions. It was found that the AM 316L steel showed the best creep resistance in the stress-relieved condition. In-situ tensile tests were performed using scanning electron microscopy and 1-ID beamline at the Advanced Photon Source to elucidate the deformation and fracture behavior of AM 316L and the evolution of crystalline stress, dislocations, and pore distribution. Using these in-situ testing data, an in-depth analysis of the roles of microstructural features in deformation and fracture processes is presented herein. The final section of the document introduces ongoing and future activities for materials testing and characterization, including irradiation effect studies and ball punch testing on AM 316L and AM IN718 alloys.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Example Evaluation of a Representative Heat Pipe Test Article Design for Structural Acceptability using ASME Design Rules

This report describes a design analysis of a test article mimicking a core block of a heat-pipe mi-croreactor using the ASME Boiler & Pressure Vessel Code Section III, Division 5, Subsection HB, Subpart B rules. These rules cover the design and construction of elevated temperature nu-clear reactor structural components, like the core block of a heat-pipe microreactor emulated by the test article. The purposes of the report are to: (1) provide a step-by-step example of applying the ASME rules to a reasonable core block geometry and corresponding loading conditions, (2) to provide design feedback on the test article, and (3) to evaluate the ASME rules for use in the design of complex heat-pipe microreactor components. The test article design has a relatively short ASME design life, limited by high thermal stresses. The current ASME rules are adequate for evaluating the core block component designs, though they could be optimized to increase the design efficiency and reduce the amount of designer/analyst time required to execute the design process. The report covers both the current, 2019 edition ASME rules and modified, currently unapproved, rules designed to improve the design process for components with complex geometries and high secondary stresses, like the core block test article.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Corrosion Testing Of Additively Manufactured Stainless Steel 316H In Molten Salt Environments

The development of a new ASTM standard for evaluating the corrosion resistance of additive manufactured (AM) stainless steel (SS) 316H in chloride molten salts is critical for the use of these materials in extreme environments such as molten salt reactors (MSRs). This report pertains to a work package of the Advaned Materials and Manufacturing Technologies (AMMT) developing a systematic methodology to link changes in AM fabrication parameters, namely surface finishing, porosity, microstructure, and chemical heterogeneity, to corrosion performance in NaCl-MgCl2 salt, a proposed secondary coolant for MSRs. During Fiscal Year 2024, Idaho National Laboratory investigators in the AMMT program, utilized SS316H bars, fabricated with laser bed powder fusion at Los Alamos National Laboratory, to establish and optimize the workflow for evaluating these process-to-performance relationships. Standard practices for specimen preparation were established using these specimens, with particular focus on descaling and sectioning methods that align with ASTM guidelines. A comprehensive experimental design for static corrosion testing was developed, with pre- and post-exposure analysis utilizing optical microscopy and scanning electron microscopy. So far standard descaling techniques were optimized, one static corrosion test was conducted on the LANL AM SS316H specimens, and pre- and post-corrosion practices were established. In addition, the work package yielded a review paper on corrosion testing gaps for AM materials in nuclear applications and submitted a proposal for a rapid-turnaround experiment to the Nuclear Science User Facilities Program to investigate the combined effects of proton irradiation and corrosion on AM SS316H. This work package establishes a foundation for evaluating processing-to-performance relationships for AM SS316H in harsh conditions, contributing to the safe and efficient design of components for next-generation nuclear reactors. The creation of a standardized methodology and the generation of relevant publications and future research pathways represent significant strides towards integrating AM materials into critical applications where corrosion resistance is paramount.

36 MATERIALS SCIENCE↗