Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Linear response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Parameter Reduction of Composite Load Model Using Active Subspace Method

Over the past decades, the increasing penetration of distributed energy resources (DERs) has dramatically changed the power load composition in the distribution networks. The traditional static and dynamic load models can hardly capture the dynamic behavior of modern loads especially for fault-induced delayed voltage recovery (FIDVR) events. Thus, a more comprehensive composite load model with combination of static load, different types of induction motors, single-phase A/C motor, electronic load and DERs has been proposed by Western Electricity Coordinating Council (WECC). However, due to the large number of parameters and model complexity, the WECC composite load model (WECC CMLD) raises new challenges to power system studies. To overcome these challenges, in this paper, a cutting-edge parameter reduction (PR) approach for WECC CMLD based on active subspace method (ASM) is proposed. Firstly, the WECC CMLD is parameterized in a discrete-time manner for the application of the proposed method. Then, parameter sensitivities are calculated by discovering the active subspace, which is a lower-dimensional linear subspace of the parameter space of WECC CMLD in which the dynamic response is most sensitive. The interdependency among parameters can be taken into consideration by our approach. Finally, the numerical experiments validate the effectiveness and advantages of the proposed approach for WECC CMLD model.

active subspace↗
DOE OSTI2026

Electrochemical Modeling of PID Leakage Current of PV Modules: Steady-State Current, Transient Current, and RC-Equivalent Circuit

Potential-induced degradation (PID) remains a significant reliability concern for photovoltaic (PV) modules, arising when a voltage difference between the module frame and the solar cells drives unintended leakage current through the glass-encapsulant stack. Although PID ultimately manifests as PID-s, PID-p, or PID-c, the underlying behavior of the leakage current-its magnitude and time dependence-requires clearer electrochemical interpretation. Traditional explanations attribute the initial transient current to bulk capacitive elements of the glass, encapsulant, and antireflection coatings, and the steady-state current according to their effective ohmic resistance. More recent studies, however, indicate that electrochemical charge-transfer processes at the encapsulant-metallization interface can play a dominant role in defining the leakage-current path. This paper develops a unified electrochemical framework for modeling PID leakage current. First, an RC-equivalent circuit is formulated by combining conventional RC elements with a Randles-type interface to capture transient leakage current through double-layer capacitance and faradaic processes at ionic-electronic boundaries. Second, the steady-state current-voltage behavior is explained using a linearized Butler-Volmer relationship, showing that the measured ohmic response corresponds to the low-overpotential limit of charge-transfer kinetics. Analytical results demonstrate that, for typical module materials-3.2-mm soda-lime glass and 0.45-mm encapsulant-the dominant modulators to PID leakage current are the glass surface resistance (under dry-surface conditions), the glass bulk capacitance, and the encapsulant resistance (under wet-surface conditions), with soda lime glass surface and EVA/POE encapsulant resistances primarily governing steady-state current. The proposed electrochemical model is validated against measured leakage-current data, showing good agreement in both the magnitude and the time-dependent evolution of PID leakage current.

14 SOLAR ENERGY↗
DOE OSTI2022

Minimum feature size control in level set topology optimization via density fields

A level set topology optimization approach that uses an auxiliary density field to nucleate holes during the optimization process and achieves minimum feature size control in optimized designs is explored. The level set field determines the solid-void interface and the density field describes the distribution of a fictitious porous material using the solid isotropic material with penalization. These fields are governed by two sets of independent optimization variables which are initially coupled using a penalty for hole nucleation. The strength of the density field penalization and projection is gradually increased during the optimization process to promote a 0-1 density distribution. In addition, a second penalty regulates the evolution of the density field in the void phase. The treatment of the density field combined with the second penalty mitigate the appearance of small design features. The minimum feature size of optimized designs is controlled by the radius of the linear filter applied to the density optimization variables. The structural response is predicted by the extended finite element method, the sensitivities by the adjoint method, and the optimization variables are updated by a gradient-based optimization algorithm. Numerical examples investigate the robustness of this approach with respect to algorithmic parameters and mesh refinement. The results show the applicability of the combined density level set topology optimization approach for both optimal hole nucleation and for minimum feature size control in 2D and 3D. This comes, however, at the cost of a more complex problem formulation and additional computational cost due to an increased number of optimization variables.

42 ENGINEERING↗
DOE OSTI2021

Desalination metamodels and a framework for cross-comparative performance simulations

There is an opportunity to save energy and reduce operational expenses when choosing a suitable desalination method aided by computational modeling. Existing models are not conducive to generalized comparisons between different desalination methods. Therefore, the work in this study developed metamodels for six desalination methods, grouped them into thermal and molecular transport families, and validated their predictive performance within 9% difference from published data. This validated framework allowed comparisons of desalination methods at their prescribed ranges of operational conditions that they were designed for. These conditions specify feed salinity ranges of 1.6 to 2.4 g/kg for Capacitive Deionization and Reverse Osmosis (RO), 2.8 to 4.2 g/kg for Electrodialysis, 28 to 42 g/kg for Thermovapor Compression and Humidification-Dehumidification, and 37 to 55 g/kg for Multi-Effect Distillation (MED). Despite different operational conditions, all models exhibit non-linear, positive correlation between energy consumption and system size in response to feed salinity and production rate. The framework is also employed in a cross-comparative analysis between MED and RO whose results suggest that energy intensity for MED is an order of magnitude greater than RO for the same operational conditions, but actual operational costs are comparable. Overall, the framework is ready for deployment in case studies of actual desalination plants.

42 ENGINEERING↗
DOE OSTI2020

Three-dimensional modeling and simulations of single-crystal and bi-crystal titanium for high-strain-rate loading conditions

High purity single crystal titanium (Ti) under shock wave loading is modeled under both one-dimensional and three-dimensional cylindrical conditions. Cylinder sizes of 10 μm and 20 μm radius are both considered in order to assess influence of boundary conditions. A thermodynamically consistent single crystal model for application to shock conditions is presented. The model accounts for the coupled non-linear elastic, dislocation slip, deformation twinning, and structural phase transformation response of the titanium material. Plate impact experiment results using a copper flyer are used to compare against the simulations for crystals oriented in [0001] and [10$\overline1$1] crystallographic directions. The one-dimensional and threedimensional simulations of the two differently oriented single crystals indicate differences between the one-dimensional and three-dimensional representation, especially for the [10$\overline1$1] oriented single crystal. This orientation breaks the relative orientation symmetry between the crystal and cylinder which otherwise exists for the [0001] oriented single crystal. A significant amount of heterogeneity in the field response of the[10$\overline1$1] oriented simulation was demonstrated due to the highly coupled nature of the deformation. A bi-crystal model composed of both the [0001] and [10$\overline1$1] orientations with the boundary between the two along the axis of the cylinder is also considered for a cylinder model size of 10 μm. The results indicate a strong interaction between the two grains that affects the ω phase volume fraction achieved relative to the single crystal calculations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Beware of fake ν ’s: The effect of massive neutrinos on the nonlinear evolution of cosmic structure

Massive neutrinos suppress the growth of cosmic structure on small, nonlinear scales. It is thus often proposed that using statistics beyond the power spectrum can tighten constraints on the neutrino mass by extracting additional information from these nonlinear scales. We study the information content regarding neutrino mass at the field level, quantifying how much of this information arises from the difference in nonlinear evolution between a cosmology with one fluid [cold dark matter (CDM)] and two fluids ( CDM + neutrinos ). We do so by running two N -body simulations, one with and one without massive neutrinos, both with the same phases, and matching their linear power spectrum at a given low redshift. This effectively isolates the information encoded in the linear initial conditions from the nonlinear cosmic evolution. We demonstrate that, for k ≲ 1 h / Mpc , and for a single redshift, there is negligible difference in the real-space CDM field between the two simulations. This suggests that all the information regarding neutrino mass is in the linear power spectrum set by the initial conditions. Thus, any probe based on the CDM field alone will have negligible constraining power beyond that which exists at the linear level over the same range of scales. Consequently, any probe based on the halo field will contain little information beyond the linear power. We find similar results for the matter field responsible for weak lensing. We also demonstrate that there may be much information beyond the power spectrum in the 3D matter field; however, this is not observable in modern surveys via dark matter halos or weak lensing. Finally, we show that there is additional information to be found in redshift space.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Physical Interpretation of Early Battery Life Prediction Models

Early battery life prediction models are most useful for R&D if they help us understand the early changes in battery electrochemical response that correspond with long-term degradation and failure. Linear regression models such as Fused lasso and Partial Least Squares can fit coefficients directly to high-dimensional electrochemical data like capacity-voltage and ΔV–state-of-charge, i.e., Q(V) and ΔV(SOC) curves, learning coefficients that can be physically interpreted. We leverage the ISU-ILCC battery aging data set to learn high-dimensional coefficients for early battery life prediction from traditional slow-rate capacity check data, demonstrating learning on Q(V), d Q· d V −1 , and ΔV(SOC) curves. A thorough study on the dependence of coefficient values on train/test size and data preprocessing methods is made, demonstrating the reliability of high-dimensional regression approaches unless very small amounts of data are used for model training. For this data set, coefficients from Q(V) and d Q· d V −1 models highlight changes in electrode stoichiometry due to lithium loss, while ΔV(SOC) coefficients highlight changes in positive electrode diffusivity due to particle cracking as well as electrode stoichiometry shifts. By directly interpreting the coefficients of a regression model, we make physical insights into battery degradation mechanisms without requiring the assumptions of traditional battery data analysis methods.

25 ENERGY STORAGE↗
DOE OSTI2021

High Data Rate Detector for Neutron Reflectometer

Neutron reflectometers are a class of instruments that employ neutron diffraction for measuring the structure of thin films. The technique provides valuable information over a wide variety of scientific and technological applications including chemical aggregation, polymer and surfactant adsorption, structure of thin film magnetic systems, biological membranes, etc. Such instruments are considered to be one of the most important in the neutron science field. Newer facilities place growing demands on the count rate capability of the specialized neutron detectors required. Proportional Technologies completed the Phase I effort successfully with a fully operational prototype detector built at PTI and tested at the CG1A neutron beam of the High Flux Isotope Reactor (HFIR, Oak Ridge, TN). The prototype incorporated 3 panels of 14 copper-walled cells each (total of 42 cells), each lined with 1.3 μm of 10B4C. The detector was tested for efficiency, spatial resolution, count rate linearity, uniformity, overlap and scatter. Testing revealed stable operation, uniform response across cells, and successful resolution of individual cells. The maximum count rate tested in the 3 panels combined was 590 kHz, limited by a deadtime of about 1 μs in the digital electronics. The local rate measured in a single cell showed no deadtime losses up to 810 cps/mm2, indicating that a rate of 20 Mhz can be supported in the 308-cell detector planned for Phase II.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Does the rotational direction of a wind turbine impact the wake in a stably stratified atmospheric boundary layer?

Stably stratified atmospheric boundary layers are often characterized by a veering wind profile, in which the wind direction changes clockwise with height in the Northern Hemisphere. Wind-turbine wakes respond to this veer in the incoming wind by stretching from a circular shape into an ellipsoid. We investigate the relationship between this stretching and the direction of the turbine rotation by means of large-eddy simulations. Clockwise rotating, counterclockwise rotating, and non-rotating actuator disc turbines are embedded in wind fields of a precursor simulation with no wind veer and in wind fields with a Northern Hemispheric Ekman spiral, resulting in six combinations of rotor rotation and inflow wind condition. The wake strength, extension, width, and deflection depend on the interaction of the meridional component of Ekman spiral with the rotational direction of the actuator disc, whereas the direction of the disc rotation only marginally modifies the wake if no veer is present. The differences result from the amplification or weakening/reversion of the spanwise and the vertical wind components due to the effect of the superposed disc rotation. They are also present in the streamwise wind component of the wake and in the total turbulence intensity. In the case of an counterclockwise rotating actuator disc, the spanwise and vertical wind components increase directly behind the rotor, resulting in the same rotational direction in the whole wake while its strength decreases downwind. In the case of a clockwise rotating actuator disc, however, the spanwise and vertical wind components of the near wake are weakened or even reversed in comparison to the inflow. This weakening/reversion results in a downwind increase in the strength of the flow rotation in the wake or even a different rotational direction in the near wake in comparison to the far wake. The physical mechanism responsible for this difference can be explained by a simple linear superposition of a veering inflow with a Rankine vortex.

17 WIND ENERGY↗
DOE OSTI2022

Nonlinear deformation and elasticity of BCC refractory metals and alloys

Application of isotropic pressure or uniaxial strain alters the elastic properties of materials; sufficiently large strains can drive structural transformations. Linear elasticity describes stability against infinitesimal strains, while nonlinear elasticity describes the response to finite deformations. Here, it was previously shown that uniaxial strain along [100] drives refractory metals and alloys towards mechanical instabilities. These include an extensional instability, and a symmetry-breaking orthorhombic distortion caused by a Jahn-Teller-Peierls instability that splays the cubic lattice vectors. Here we analyze these transitions in depth. Eigenvalues and eigenvectors of the Wallace tensor identify and classify linear instabilities in the presence of strain. We show that both instabilities are discontinuous, leading to discrete jumps in the lattice parameters. We provide physical intuition for the instabilities by analyzing the changes in first-principles energy, stress, bond lengths, and angles upon application of strain. Electronic band structure calculations show differential occupation of bonding and antibonding orbitals, driven by the changing bond lengths and leading to the structural transformations. Strain thresholds for these instabilities depend on the valence electron count.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exciton Enhanced Nonlinear Optical Responses in Monolayer h-BN and MoS 2 : Insight from First-Principles Exciton-State Coupling Formalism and Calculations

Excitons are vital in the photophysics of materials, especially in low-dimensional systems. The conceptual and quantitative understanding of excitonic effects in nonlinear optical (NLO) processes is more challenging compared to linear ones. Here, we present an ab initio approach to second-order NLO responses, incorporating excitonic effects, that employs an exciton-state coupling formalism and allows for a detailed analysis of the role of individual excitonic states. Taking monolayer h-BN and MoS 2 as two prototype 2D materials, we calculate their second harmonic generation (SHG) susceptibility and shift current conductivity tensor. We find strong excitonic enhancement in the NLO responses requires that the resonant excitons are not only optically bright themselves but also able to couple strongly to other bright excitons. Our results explain the occurrence of two strong peaks in the SHG of monolayer h-BN and why the A and B excitons of MoS 2 unexpectedly exhibit minimal excitonic enhancement in both SHG and shift current generation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Structural, chemical, and electronic control in Co–SiNx granular metals for high-pass filter applications

Granular metals, consisting of nanoscale conducting and insulating regions, have been studied for more than 50 years for fundamental and applied research. Granular metals exhibit non-linear conductivity vs frequency behavior, consistent with the universal power law response, and have recently been suggested for high-pass filter applications. Here, we report that cobalt–silicon nitride (Co–SiNx) granular metals with optimized sputter conditions and post-growth annealing exhibit an exceptional 109 increase in conductivity at 1 MHz compared to the DC conductivity. The improved frequency response is correlated with structural and chemical improvements examined via scanning transmission electron microscopy and x-ray photoemission spectroscopy. While we focus on improvements for high-pass filter applications, the structural, chemical, and electronic control demonstrated here will benefit a variety of granular metal and nanoparticle applications.

Annealing↗
DOE OSTI2023

Sensitivity of the Southern Hemisphere Wintertime Teleconnection to the Location of ENSO Heating

The Southern Hemisphere extratropical atmospheric circulation response to anomalous convection in the tropical western and eastern Pacific Ocean is distinctly different. The response to westward-located heating has a meridional dipole in the South Pacific with large zonal scale and appears unable to be interpreted simply as a stationary Rossby wave train that disperses poleward and eastward from a tropical source like the meridionally arched response to eastward-located heating. Here, this study investigates the cause of this asymmetry by examining the daily evolution of the response to suddenly switching on steady diabatic heating over a western and central/eastern equatorial Pacific location using large-ensemble integrations from the Community Atmosphere Model version 5. We focus on the austral winter months when the subtropical jet supports the development of an effective Rossby wave source in the subtropical westerlies and acts as a waveguide. We show that the subtropical jet strongly influences the height response to the western tropical Pacific heating, promoting prominent zonal circumglobal propagation. Development of a transient eddy feedback in the extratropical storm track after approximately 10 days appears to play a primary role in establishing the time-mean response, which we test through comparison with similar experiments conducted using a simplified linear model. Conversely, the height anomalies for eastern tropical Pacific heating, farther away from the subtropical jet core, have larger meridional propagation, dispersing in a typical Hoskins–Karoly manner into the Southern Hemisphere extratropics, while the transient eddy feedback plays a secondary role for the establishment of the steady response.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Experimental Investigation of Low-Frequency Distributed Acoustic Strain-Rate Responses to Propagating Fractures

Summary Low-frequency distributed acoustic sensing (LF-DAS) responds to strain changes due to far-field fracture propagation. To better understand the LF-DAS response to fracture propagation, we performed laboratory-scale hydraulic fracture experiments with embedded optical strain sensors. The objectives of this research are to generate hydraulic fractures of known geometry, measure the strain response along the embedded fiber-optic cable comparable to LF-DAS measurements, and use the results to inform the interpretation of field-derived LF-DAS data. The experiments were conducted in unconfined transparent cubic blocks with a dimension of 8 in. on each side. The block was made of transparent epoxy to visualize the fracture propagation. Fiber-optic sensing cables were embedded in the block at different distances to the source of injection. We injected dyed water through an injection tubing to generate a transverse, radial fracture along an initial flaw. An optical interrogator recorded the response of offset fiber Bragg grating (FBG) strain sensors normal to the plane of the fracture. The strain data were visualized on a waterfall plot, akin to visualizations of field-derived LF-DAS data. Dimensional analysis was used to scale the laboratory results to field conditions. We compared the evolution of the strain response at the fiber-optic cable, injection pressure, and rate with known fracture geometry. The measured strains were compared with Sneddon’s (1946) linear elastic solution for a penny-shaped crack and found to follow this behavior. The generated radial fractures in transparent media can be modeled with Sneddon’s linear elastic radial fracture model and a Mode I critical stress intensity factor. The LF-DAS characteristic response of a narrowing region of extension surrounded by compression was exhibited as a fracture that approached and intersected the fiber-optic cable. The experimentally derived strain and strain-rate waterfall plots with known fracture geometry, injection rate, and pressure response provide insight in understanding LF-DAS responses in the field. Furthermore, we developed a method to estimate fracture geometry evolution from the fiber-optic strain data and validated the method against the experimental data.

Engineering↗
DOE OSTI2022

Proteome reallocation enables the selective de novo biosynthesis of non-linear, branched-chain acetate esters

The one-carbon recursive ketoacid elongation pathway is responsible for making various branched-chain amino acids, aldehydes, alcohols, and acetate esters in living cells. Controlling selective microbial biosynthesis of these target molecules at high efficiency is challenging due to enzyme promiscuity, regulation, and metabolic burden. In this study, we present a systematic modular design approach to control proteome reallocation for selective microbial biosynthesis of branched-chain acetate esters. Through pathway modularization, we partitioned the branched-chain ester pathways into four submodules including keto-isovalerate submodule for converting pyruvate to keto-isovalerate, ketoacid elongation submodule for producing longer carbon-chain keto-acids, ketoacid decarboxylase submodule for converting ketoacids to alcohols, and alcohol acyltransferase submodule for producing branched-chain acetate esters by condensing alcohols and acetyl-CoA. By systematic manipulation of pathway gene replication and transcription, enzyme specificity of the first committed steps of these submodules, and downstream competing pathways, we demonstrated selective microbial production of isoamyl acetate over isobutyl acetate. In this work, we found that the optimized isoamyl acetate pathway globally redistributed the amino acid fractions in the proteomes and required up to 23-31% proteome reallocation at the expense of other cellular resources, such as those required to generate precursor metabolites and energy for growth and amino acid biosynthesis. From glucose fed-batch fermentation, the engineered strains produced isoamyl acetate up to a titer of 8.8 g/L (> 0.25 g/L toxicity limit), a yield of 0.22 g/g (61% of maximal theoretical value), and 86% selectivity, achieving the highest titers, yields and selectivity of isoamyl acetate reported to date.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Quantile-dependent expressivity of plasma adiponectin concentrations may explain its sex-specific heritability, gene-environment interactions, and genotype-specific response to postprandial lipemia

“Quantile-dependent expressivity” occurs when the effect size of a genetic variant depends upon whether the phenotype (e.g. adiponectin) is high or low relative to its distribution. We have previously shown that the heritability ( h 2 ) of adiposity, lipoproteins, postprandial lipemia, pulmonary function, and coffee and alcohol consumption are quantile-specific. Whether adiponectin heritability is quantile specific remains to be determined. Plasma adiponectin concentrations from 4,182 offspring-parent pairs and 1,662 sibships from the Framingham Heart Study were analyzed. Quantile-specific heritability from offspring-parent (β OP , h 2 = 2 β OP /(1 + r spouse )) and full-sib regression slopes ( β FS , h 2 = {(1 + 8r spouse β FS ) 0.05 -1}/(2r spouse )) were robustly estimated by quantile regression with nonparametric significance assigned from 1,000 bootstrap samples. Quantile-specific h 2 (± SE) increased with increasing percentiles of the offspring’s age- and sex-adjusted adiponectin distribution when estimated from β OP ( P trend = 2.2 × 10 -6 ): 0.30 ± 0.03 at the 10th, 0.33 ± 0.04 at the 25th, 0.43 ± 0.04 at the 50th, 0.55 ± 0.05 at the 75th, and 0.57 ± 0.08 at the 90th percentile, and when estimated from β FS (P trend = 7.6 × 10 -7 ): 0.42 ± 0.03 at the 10th, 0.44 ± 0.04 at the 25th, 0.56 ± 0.05 at the 50th, 0.73 ± 0.08 at the 75th, and 0.79 ± 0.11 at the 90th percentile. Consistent with quantile-dependent expressivity, adiponectin’s: (1) heritability was greater in women in accordance with their higher adiponection concentrations; (2) relationships to ADIPOQ polymorphisms were modified by adiposity in accordance with its adiponectin-lowering effect; (3) response to rosiglitazone was predicted by the 45T> G ADIPOQ polymorphism; (4) difference by ADIPOQ haplotypes increased linearly with increasing postprandial adiponectin concentrations. Adiponectin heritability is quantile dependent, which may explain sex-specific heritability, gene-environment and gene-drug interactions, and postprandial response by haplotypes.

Postprandial↗
DOE OSTI2020

Nonlinear Logistic Regression Mixture Experiment Modeling for Binary Data Using Dimensionally Reduced Components

This article presents and illustrates an approach using nonlinear logistic regression for modeling binary response data from a mixture experiment when the components can be partitioned into groups used to form dimensionally-reduced pseudocomponents (DRPs). A DRP is a linear combination of the components in a group, where the linear combinations over all groups are normalized so that the DRP proportions sum to unity. Nonlinear logistic regression is required because, after normalization of the linear combinations, the model expressed in terms of the DRPs is nonlinear in the parameters that specify the linear combinations. A method for obtaining nonparametric tolerance limits on the probability of a “success” for the binary response variable using a bootstrap approach is also presented. Having three DRPs enables viewing data and modeling results on a ternary plot even though there may be many more than three mixture components. A real database, involving whether or not nepheline crystals form in simulated nuclear waste glass after cooling, is used to illustrate the nonlinear logistic regression modeling and nonparametric tolerance limit approaches when there are three DRPs.

Waste glass, Nepheline, Mixture experiment, Logist↗