Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Electron trapping in rad-hard RCA IC's irradiated with electrons and gamma rays

Enhanced electron trapping has been observed in n-channels of rad-hard CMOS devices due to electron and gamma-ray irradiation. Room-temperature annealing results in a positive shift in the threshold potential far beyond its initial value. The slope of the annealing curve immediately after irradiation was found to depend strongly on the gate bias applied during irradiation. Some dependence was also observed on the electron dose rate. No clear dependence on energy and shielding over a delidded device was observed. The threshold shift is probably due to electron trapping at the radiation-induced interface states and tunneling of electrons through the oxide-silicon energy barrier to fill the radiation-induced electron traps. A mathematical analysis, based on two parallel annealing kinetics, hole annealing and electron trapping, is applied to the data for various electron dose rates.

Danchenko, V.↗

RF characterization of monolithic microwave and mm-wave ICs

A number of fixturing techniques compatible with automatic network analysis are presented. The fixtures are capable of characterizing GaAs Monolithic Microwave Integrated Circuits (MMICs) at K and Ka band. Several different transitions are used to couple the RF test port to microstrip. Fixtures which provide chip level de-embedding are included. In addition, two advanced characterization techniques are assessed.

Romanofsky, R. R.↗

System architecture of a gallium arsenide one-gigahertz digital IC tester

The design for a 1-GHz digital integrated circuit tester for the evaluation of custom GaAs chips and subsystems is discussed. Technology-related problems affecting the design of a GaAs computer are discussed, with emphasis on the problems introduced by long printed-circuit-board interconnect. High-speed interface modules provide a link between the low-speed microprocessor and the chip under test. Memory-multiplexer and memory-shift register architectures for the storage of test vectors are described in addition to an architecture for local data storage consisting of a long chain of GaAs shift registers. The tester is constructed around a VME system card cage and backplane, and very little high-speed interconnect exists between boards. The tester has a three part self-test consisting of a CPU board confidence test, a main memory confidence test, and a high-speed interface module functional test.

Fouts, Douglas J.↗

Numerical simulation of the flow field and fuel sprays in an IC engine

A two-dimensional model for axisymmetric piston-cylinder configurations is developed to study the flow field in two-stroke direct-injection Diesel engines under motored conditions. The model accounts for turbulence by a two-equation model for the turbulence kinetic energy and its rate of dissipation. A discrete droplet model is used to simulate the fuel spray, and the effects of the gas phase turbulence on the droplets is considered. It is shown that a fluctuating velocity can be added to the mean droplet velocity every time step if the step is small enough. Good agreement with experimental data is found for a range of ambient pressures in Diesel engine-type microenvironments. The effects of the intake swirl angle in the spray penetration, vaporization, and mixing in a uniflow-scavenged two-stroke Diesel engine are analyzed. It is found that the swirl increases the gas phase turbulence levels and the rates of vaporization.

Nguyen, H. L.↗

Current distribution in a three-dimensional IC analyzed by a perturbation method. Part 1: A simple steady state theory

The steady state current distribution in a three dimensional integrated circuit is presented. A device physics approach, based on a perturbation method rather than an equivalent lumped circuit approach, is used. The perturbation method allows the various currents to be expressed in terms of elementary solutions which are solutions to very simple boundary value problems. A Simple Steady State Theory is the subtitle because the most obvious limitation of the present version of the analysis is that all depletion region boundary surfaces are treated as equipotential surfaces. This may be an adequate approximation in some applications but it is an obvious weakness in the theory when applied to latched states. Examples that illustrate the use of these analytical methods are not given because they will be presented in detail in the future.

Edmonds, Larry D.↗

Possible significance of cubic water-ice, H2O-Ic, in the atmospheric water cycle of Mars

The possible formation and potential significance of the cubic ice polymorph on Mars is discussed. When water-ice crystallizes on Earth, the ambient conditions of temperature and pressure result in the formation of the hexagonal ice polymorph; however, on Mars, the much lower termperature and pressures may permit the crystallization of the cubic polymorph. Cubic ice has two properties of possible importance on Mars: it is an excellant nucleator of other volatiles (such as CO2), and it undergoes an exothermic transition to hexagonal ice at temperatures above 170 K. These properties may have significant implications for both martian cloud formation and the development of the seasonal polar caps.

Gooding, James L.↗

The design of radiation-hardened ICs for space - A compendium of approaches

Several technologies, including bulk and epi CMOS, CMOS/SOI-SOS (silicon-on-insulator-silicon-on-sapphire), CML (current-mode logic), ECL (emitter-coupled logic), analog bipolar (JI, single-poly DI, and SOI) and GaAs E/D (enhancement/depletion) heterojunction MESFET, are discussed. The discussion includes the direct effects of space radiation on microelectronic materials and devices, how these effects are evidenced in circuit and device design parameter variations, the particular effects of most significance to each functional class of circuit, specific techniques for hardening high-speed circuits, design examples for integrated systems, including operational amplifiers and A/D (analog/digital) converters, and the computer simulation of radiation effects on microelectronic ISs.

Kerns, Sherra E.↗

An infrared study of starbursts in the interacting galaxy pair Arp 299 (NGC 3690+IC 694)

Extensive infrared observations have been obtained of the three active regions in Arp 299. Multiaperture JHK photometry reveals that the colors of the three regions are totally different from each other, and that there are very red nuclei smaller than 4 arcsec in two of them. Multiaperture spectroscopy of the Br-gamma and the shock-excited H2 lines shows that both the atomic and molecular lines are spatially extended, indicating that Arp 299 is undergoing an active episode of star formation not only in its nuclei but also well outside of them. Although there is some evidence that suggests the presence of a compact, active galactic nucleus, a simple starburst model can explain the bolometric luminosities, production rates of ionizing photons, and H24 line luminosities of each active region in Arp 299. However, each starburst cannot last longer than 10 to the 8th yr.

Nakagawa, Takao↗

A CAM-based LZ data compression IC

A custom CMOS processor is introduced that implements the Data Compression Lempel-Ziv (DCLZ) standard, a variation of the LZ2 Algorithm. This component presently achieves a sustained compression and decompression rate of 10 megabytes/second by employing an on-chip content-addressable memory for string table storage.

Winters, K.↗

An investigation of fluid flow during induction stroke of a water analog model of an IC engine using an innovative optical velocimetry concept: LIPA

Optical measurements on an axisymmetrical quartz component engine research model were made to evaluate the flow field encountered during induction. The measurement technique is LIPA (Laser Induced Photochemical Anemometry), a non-intrusive velocimetry concept that provides an investigator of fluid flow with a tool to attain planar information about three-dimensional velocity and vorticity vectors in a single measurement step. The goal of this investigation is to further develop this measurement technique and apply it to study the induction stroke of a water analog model of a four-stroke internal combustion engine. The research conducted in the water analog model is a fundamental scientific inquiry into the flow fields that develop in the induction stroke of an engine at idling engine speeds. As this is the first investigation of its kind using LIPA technique, our goal has been to quantify, in a preliminary manner, the flow field features that develop during the intake stroke. In the process a more comprehensive understanding of the flow field features was developed, and tied to the quantification. The study evaluated the flow field of the intake stroke by estimating fields of velocity and vorticity. On the basis of these data, information about fluid dynamics during induction at engine speeds of 10, 20, and 30 RPM (corresponding to 170, 340, and 510 RPM respectively, when air is the flowing medium) for three different valve lifts was obtained. The overall development of the flow field, its energy content (kinetic, fluctuation) for the different settings of the engine parameters, vorticity information, and cyclic variations have been quantified. These have been discussed in terms of mixing performance.

Stier, Bernd↗

Low-order nonlinear dynamic model of IC engine-variable pitch propeller system for general aviation aircraft

This paper presents a dynamic model of an internal combustion engine coupled to a variable pitch propeller. The low-order, nonlinear time-dependent model is useful for simulating the propulsion system of general aviation single-engine light aircraft. This model is suitable for investigating engine diagnostics and monitoring and for control design and development. Furthermore, the model may be extended to provide a tool for the study of engine emissions, fuel economy, component effects, alternative fuels, alternative engine cycles, flight simulators, sensors, and actuators. Results show that the model provides a reasonable representation of the propulsion system dynamics from zero to 10 Hertz.

Richard, Jacques C.↗

LES on unstructured deforming meshes: Towards reciprocating IC engines

A variable explicit/implicit characteristics-based advection scheme that is second-order accurate in space and time has been developed recently for unstructured deforming meshes (O'Rourke & Sahota 1996a). To explore the suitability of this methodology for Large-Eddy Simulation (LES), three subgrid-scale turbulence models have been implemented in the CHAD CFD code (O'Rourke & Sahota 1996b): a constant-coefficient Smagorinsky model, a dynamic Smagorinsky model for flows having one or more directions of statistical homogeneity, and a Lagrangian dynamic Smagorinsky model for flows having no spatial or temporal homogeneity (Meneveau et al. 1996). Computations have been made for three canonical flows, progressing towards the intended application of in-cylinder flow in a reciprocating engine. Grid sizes were selected to be comparable to the coarsest meshes used in earlier spectral LES studies. Quantitative results are reported for decaying homogeneous isotropic turbulence, and for a planar channel flow. Computations are compared to experimental measurements, to Direct-Numerical Simulation (DNS) data, and to Rapid-Distortion Theory (RDT) where appropriate. Generally satisfactory evolution of first and second moments is found on these coarse meshes; deviations are attributed to insufficient mesh resolution. Issues include mesh resolution and computational requirements for a specified level of accuracy, analytic characterization of the filtering implied by the numerical method, wall treatment, and inflow boundary conditions. To resolve these issues, finer-mesh simulations and computations of a simplified axisymmetric reciprocating piston-cylinder assembly are in progress.

Haworth, D. C.↗

Binning for IC Quality: Experimental Studies on the SEMATECH Data

The earlier smaller bipolar study did not provide a high enough bin 0 population to directly observe test escapes and thereby estimate defect levels for the best bin. Results presented here indicate that the best bin can be reasonably expected to show a 2 - 5 factor improvement in defect levels over the average for the lot for moderate to high yields (the overall yield for these experiments was approximately 65%). The experiments also confirm the dependence of the best bin quality on test transparency. The defect level improvement is poorer for the case Of IDDQ escapes where the tests applied had a much higher escape rate. Overall experimental results are consistent with analytical projections for typical values of the clustering parameter in [9]. The final version of this paper will include extensive analysis to validate the analytical models based on this data.

Singh, Adit D.↗

Measuring the Radius of a Neutron Star; Origin of High X-Ray Luminosities in Optically Passive Galaxies; Resolving the Source of X-Rays in IC 1613"

This recently expired grant has supported the work of the PI, his students, and his collaborators on a variety of ROSAT projects over the past three years. Annual reports have summarized much of the work accomplished; here we provide a brief review of the work resulting from this effort, and a summary of the personnel who have benefited from its support. A high resolution ROSAT HRI X-ray image of the Local Group dwarf IC1613 revealed that the principal source of X-ray emission in this direction arises in a background cluster of galaxies, as first suggested by Eskridge (1995). In addition, however, we found a bright X-ray source coincident with the only known supernova remnant in this galaxy, S # 8. Extensive ground-based follow-up observations in the radio and optical regimes were conducted. We confirmed the nonthermal radio spectral index of the source and measured its extent to be approx. 3 sec at 20 cm. Imaging spectrophotometric observations taken with the multi-pupil spectrograph of the Special Astrophysical Observatory in the FSU allowed us to determine the density and velocity distribution of the gas in the remnant. The simultaneous presence of luminous X-ray and optical emission suggests a relatively young remnant in which the outward-moving shock has recently encountered dense material. Many of this object's properties are similar to those of the brightest optical remnant in the Large Magellanic Cloud, N49. Another potential source of X-rays in this galaxy which featured prominently in our original proposal, an Oxygen Wolf-Rayet star with a large surrounding wind-blown bubble, was not detected.

Helfand, David J.↗

High-Q X-Band and K-Band Micromachined Spiral Inductors for Use in Si-Based ICs

A micromachined structure with reduced parasitics is proposed to enhance the resonant frequency and the quality factor (Q) of a spiral inductor. Inductors with various etch depths have been fabricated on a high resistivity Si substrate. Two-port S-parameters measurement is taken to characterize the performance of the inductors. With an etch depth of 20 micron, a fabricated 1.8 nH spiral inductor achieves a maximum resonant frequency of 25.6 GHz and a maximum Q of 20.2 at 14.5 GHz. This technology is compatible with SiGe/Si HBT technology, and the spiral inductors are especially suitable for Si-based monolithic microwave integrated circuit (MMIC) applications.

Lu, Liang-Hung↗

PRACA Enhancement Pilot Study Report: Engineering for Complex Systems Program (formerly Design for Safety), DFS-IC-0006

This technology evaluation report documents the findings and recommendations of the Engineering for Complex Systems Program (formerly Design for Safety) PRACA Enhancement Pilot Study of the Space Shuttle Program's (SSP's) Problem Reporting and Corrective Action (PRACA) System. A team at NASA Ames Research Center (ARC) performed this Study. This Study was initiated as a follow-on to the NASA chartered Shuttle Independent Assessment Team (SIAT) review (performed in the Fall of 1999) which identified deficiencies in the current PRACA implementation. The Pilot Study was launched with an initial qualitative assessment and technical review performed during January 2000 with the quantitative formal Study (the subject of this report) started in March 2000. The goal of the PRACA Enhancement Pilot Study is to evaluate and quantify the technical aspects of the SSP PRACA systems and recommend enhancements to address deficiencies and in preparation for future system upgrades.

Korsmeyer, David↗

Liquid water in the domain of cubic crystalline ice Ic

Vapor-deposited amorphous water ice when warmed above the glass transition temperature (120-140 K), is a viscous liquid which exhibits a viscosity vs temperature relationship different from that of liquid water at room temperature. New studies of thin water ice films now demonstrate that viscous liquid water persists in the temperature range 140-210 K. where it coexists with cubic crystalline ice. The liquid character of amorphous water above the glass transition is demonstrated by (1) changes in the morphology of water ice films on a nonwetting surface observed in transmission electron microscopy (TEM) at around 175 K during slow warming, (2) changes in the binding energy of water molecules measured in temperature programmed desorption (TPD) studies, and (3) changes in the shape of the 3.07 micrometers absorption band observed in grazing angle reflection-absorption infrared spectroscopy (RAIRS) during annealing at high temperature. whereby the decreased roughness of the water surface is thought to cause changes in the selection rules for the excitation of O-H stretch vibrations. Because it is present over such a wide range of temperatures, we propose that this form of liquid water is a common material in nature. where it is expected to exist in the subsurface layers of comets and on the surfaces of some planets and satellites.

NASA Center ARC↗