Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Generative Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Solar Array at Very High Temperatures: Ground Tests

Solar array design for any spacecraft is determined by the orbit parameters. For example, operational voltage for spacecraft in Low Earth Orbit (LEO) is limited by significant differential charging due to interactions with low temperature plasma. In order to avoid arcing in LEO, solar array is designed to generate electrical power at comparatively low voltages (below 100 volts) or to operate at higher voltages with encapsulation of all suspected discharge locations. In Geosynchronous Orbit (GEO) differential charging is caused by energetic electrons that produce differential potential between the coverglass and the conductive spacecraft body in a kilovolt range. In such a case, the weakly conductive layer over coverglass, indium tin oxide (ITO) is one of the possible measures to eliminate dangerous discharges on array surface. Temperature variations for solar arrays in both orbits are measured and documented within the range of minus150 degrees Centigrade to plus 1100 degrees Centigrade. This wide interval of operational temperatures is regularly reproduced in ground tests with radiative heating and cooling inside a shroud with flowing liquid nitrogen. The requirements to solar array design and tests turn out to be more complicated when planned trajectory crosses these two orbits and goes closer to the Sun. The conductive layer over coverglass causes a sharp increase in parasitic current collected from LEO plasma, high temperature may cause cracks in encapsulating (Room Temperature Vulcanizing (RTV) material; radiative heating of a coupon in vacuum chamber becomes practically impossible above 1500 degrees Centigrade; conductivities of glass and adhesive go up with temperature that decrease array efficiency; and mechanical stresses grow up to critical magnitudes. A few test arrangements and respective results are presented in current paper. Coupons were tested against arcing in simulated LEO and GEO environments under elevated temperatures up to 2000 degrees Centigrade. The dependence of leakage current on temperature was measured, and electrostatic cleanness was verified for coupons with antireflection (AR) coating over the indium tin oxide (ITO) layer.

differential charging↗
NASA NTRS1972

Nonuniform flow field generation for supersonic compressor stator development: Design and preliminary results

Design and preliminary results are given for a technique which can generate a nonuniform flow similar to the discharge of an impulse supersonic compressor rotor. The technique utilizes a carefully contoured, two-dimensional blunt body in a conventional hypersonic wind tunnel to generate the required flow field. To show the effects of the flow vorticity, a cascade of impulse-type blades was tested in this test stream. Some preliminary performance data are given along with comparison with previously determined uniform flow results.

Lipfert, F. W.↗
NASA NTRS1995

The design and development of a third generation OSEE instrument

Optically Stimulated Electron Emission (OSEE) has been used to quantify surface contamination in the aerospace community. As advances are made towards the understanding of OSEE, it is desirable to incorporate technological advances with succeeding generations of instrumentation, so that improvements in the practical application of OSEE may be disseminated among the user community. Several studies undertaken by Yost, Welch, Abedin and others have expanded the knowledge base related to the underlying principles of OSEE. The conclusions of these studies, together with inputs from the user community were the foundation upon which the development of a third generation OSEE instrument was based. This manuscript describes the significant improvements incorporated into a third generation OSEE instrument as well as the elements unique to its design.

Perey, D. F.↗
NASA NTRS2016

Design and Analyses of High Aspect Ratio Nozzles for Distributed Propulsion Acoustic Measurements

A series of three convergent, round-to-rectangular high aspect ratio (HAR) nozzles were designed for acoustic testing at the NASA Glenn Research Center Nozzle Acoustic Test Rig (NATR). The HAR nozzles had exit area aspect ratios of 8:1, 12:1, and 16:1. The nozzles were designed to mimic a distributed propulsion system array with a slot nozzle. The nozzle designs were screened using Reynolds-Averaged Navier-Stokes (RANS) simulations. In addition to meeting the geometric constraints required for testing in the NATR, the HAR nozzles were designed to be free of flow features that would produce unwanted noise (e.g., flow separations) and to have uniform flow at the nozzle exit. Multiple methods were used to generate HAR nozzle designs. The final HAR nozzle designs were generated in segments using a computer code that parameterized each segment. RANS screening simulations showed that intermediate nozzle designs suffered flow separation, a normal shockwave at the nozzle exit (caused by an aerodynamic throat produced by boundary layer growth), and non-uniform flow at the nozzle exit. The RANS simulations showed that the final HAR nozzle designs were free of flow separations, but were not entirely successful at producing a fully uniform flow at the nozzle exit. The final designs suffered a pair of counter-rotating vortices along the outboard walls of the nozzle. The 16:1 aspect ratio HAR nozzle had the least uniform flow at the exit plane; the 8:1 aspect ratio HAR nozzles had a fairly uniform flow at the nozzle exit plane.

acoustic measure↗
NASA NTRS2014

Automated Tetrahedral Mesh Generation for CFD Analysis of Aircraft in Conceptual Design

The paper introduces an automation process of generating a tetrahedral mesh for computational fluid dynamics (CFD) analysis of aircraft configurations in early conceptual design. The method was developed for CFD-based sonic boom analysis of supersonic configurations, but can be applied to aerodynamic analysis of aircraft configurations in any flight regime.

Ordaz, Irian↗
NASA NTRS2018

Incorporating Test Data for Small UAS at the Conceptual Design Level

Increasing demand for improved capabilities of small unmanned aircraft systems (sUAS) has generated interest in improving the design techniques for these vehicles. sUAS have typically been designed using iterative methods with multiple prototypes, but advancements in aircraft design software will make it possible to generate conceptual designs of very small VTOL aircraft with reduced hardware prototyping. This paper describes a research effort to generate a conceptual design of an approximately 6-lb quadcopter using the NASA rotorcraft design software NDARC. Wind tunnel and hover test data are used to validate and refine the conceptual design results. The effects of parametric design variations on vehicle scale are shown. The design study described herein shows that the NDARC software, which was designed for full-scale rotorcraft, can be used to design and evaluate sUAS vehicles.

Russell, Carl R.↗
NASA NTRS2004

Integrated System Design for Air Revitalization in Next Generation Crewed Spacecraft

The capabilities of NASA's existing environmental control and life support (ECLS) system designs are inadequate for future human space initiatives that involve long-duration space voyages and interplanetary missions. This paper discusses the concept of an integrated system of CO2 removal and trace contaminant control units that utilizes novel gas separation and purification techniques and optimized thermal and mechanical design, for future spacecraft. The integration process will enhance the overall life and economics of the existing systems by eliminating multiple mechanical devices with moving parts.

Mulloth, Lila↗
NASA NTRS2016

Failure Simulation Testing of the Z-1 Spacesuit Titanium Bearing Assemblies

The Z-2 is a candidate for NASA's next generation spacesuit, designed for a range of possible missions with enhanced mobility for spacewalks both on planetary surfaces and in microgravity. Increased mobility was accomplished through innovations in shoulder and hip joints, using a number of new bearings to allow spacesuit wearers to dip, walk, and bend with ease; all important tasks for a planetary explorer collecting samples or traveling over rough terrain. The Advanced Spacesuit Development Team of NASA Johnson Space Center requested that the NASA White Sands Test Facility (WSTF) perform a series failure simulation tests on three titanium bearing assemblies, an elemental part of the joint construction used in new spacesuit designs. This testing simulated two undetected failures within the bearings and as a result the objective of this test program was to evaluate whether a failed or failing bearing could result in ignition of the titanium race material due to friction. The first failure was an inner seal leak sufficient to pressurize the race with +99 percent oxygen. The second failure was an improperly installed or mismatched ball port that created a protrusion in the ball bearing race, partially obstructing the nominal rolling path of each ball bearing. When the spacesuit bearings are assembled, bearing balls are loaded into the assembly via a ball port. The ball port is specific and unique to each bearing assembly (matched pair). The simulated mismatched ball port is a significant source of friction, which would be caused by an assembly error. To evaluate this risk, the bearings were cycled in a simulated worst-case scenario environment, with operational loads, and potential flaw conditions. During test the amount of actuation torque required and heat generated through continuous operation were measured and the bearings were observed for sparks or burning events. This paper provides detailed descriptions of the test hardware, methodology, and results.

de Baca, Richard C.↗
NASA NTRS1985

Second-generation mobile satellite system. A conceptual design and trade-off study

In recent years, interest has grown in the mobile satellite (MSAT) system, a satellite-based communications system capable of providing integrated voice and data services to a large number of users. To explore the potential of a commercial mobile satellite system (MSS) beyond the horizon of the first generation, using technologies of the 1990's and to assist MSAT-X in directing its efforts, a conceptual design has been performed for a second-generation system to be launched around the mid-1990's. The design goal is to maximize the number of satellite channels and/or minimize the overall life-cycle cost, subject to the constraint of utilizing a commercial satellite bus with minimum modifications. To provide an optimal design, a series of trade-offs are performed, including antenna sizing, feed configurations, and interference analysis. Interference is a serious problem for MSAT and often an overlapping feed design is required to reduce interbeam interference. The trade-off studies will show that a simple non-overlapping feed is sufficient for the second-generation system, thus avoiding the need for the complicated beam-forming network that is associated with the overlapping feed designs. In addition, a system that operates at L-band, an alternative frequency band that is being considered by some for possible MSAT applications, is also presented.

Sue, M. K.↗
NASA NTRSDate not supplied

Advances in PSP Testing in LaRC High Reynolds Number Facilities

The use of luminescent coatings for the global measurement of surface aerodynamic properties at full-flight Reynolds numbers has been ongoing at the NASA Langley Research Center since the late 1990s, beginning with Temperature Sensitive Paint (TSP) for boundary layer analysis at the 0.3-m Transonic Cryogenics Tunnel. Since then, significant work has been made to extend these measurements to pressure using Pressure Sensitive Paint (PSP) as well as develop systems for application in larger scale, full-flight Reynolds number facilities, such as the National Transonic Facility (NTF). Recently, a system for the measurement of time-resolved pressure using recently developed unsteady PSP (uPSP) formulations has been designed and implemented in the Transonic Dynamics Tunnel (TDT). The use of PSP (or uPSP) in either of these large scale, full-fight Reynolds number wind tunnels is complicated by the fact that both facilities operate best in oxygen deficient environments; however, the PSP technique relies on the presence of oxygen to work. The NTF is typically operated in cryogenic conditions, which is achieved using liquid nitrogen. In this facility, temperatures can reach as low as 116 K (-250 °F) with nominal oxygen concentrations of less than 50 ppm. This has resulted in the development of specialized PSP formulations that can operate in the cryogenic environment with the introduction of low amounts of oxygen (typically less than 2000 ppm) for PSP response. Likewise, to achieve full-flight Reynolds number conditions in the TDT, the atmosphere in the tunnel is replaced with a “heavy gas” of R-134A (1,1,1,2-tetrafluoroethane), which also has minimal oxygen native in the flow. The use of uPSP in this case will also depend on the introduction of trace amounts of oxygen, with the precise concentrations to be determined in an upcoming test. This presentation will describe some recent advancements that have been made for PSP measurements in both facilities. For the NTF system, there has been significant development of enhanced lighting for use at cryogenic conditions, as well as improvements in the application efficiency of the PSP. Furthermore, there are efforts underway to incorporate advanced data analysis techniques to acquire additional surface aerodynamic properties using the PSP technique that can yield not only improved experimental efficiency, but also provide data needed for next generation vehicle design and development. For the uPSP system in TDT, significant efforts to improve the data transfer rates to a high-performance computing environment for analysis are underway and performance and initial results from the system in the heavy-gas environment will be presented.

Pressure Sensitive Paint↗
NASA NTRS1994

Empirical Modeling of Plant Gas Fluxes in Controlled Environments

As humans extend their reach beyond the earth, bioregenerative life support systems must replace the resupply and physical/chemical systems now used. The Controlled Ecological Life Support System (CELSS) will utilize plants to recycle the carbon dioxide (CO2) and excrement produced by humans and return oxygen (O2), purified water and food. CELSS design requires knowledge of gas flux levels for net photosynthesis (PS(sub n)), dark respiration (R(sub d)) and evapotranspiration (ET). Full season gas flux data regarding these processes for wheat (Triticum aestivum), soybean (Glycine max) and rice (Oryza sativa) from published sources were used to develop empirical models. Univariate models relating crop age (days after planting) and gas flux were fit by simple regression. Models are either high order (5th to 8th) or more complex polynomials whose curves describe crop development characteristics. The models provide good estimates of gas flux maxima, but are of limited utility. To broaden the applicability, data were transformed to dimensionless or correlation formats and, again, fit by regression. Polynomials, similar to those in the initial effort, were selected as the most appropriate models. These models indicate that, within a cultivar, gas flux patterns appear remarkably similar prior to maximum flux, but exhibit considerable variation beyond this point. This suggests that more broadly applicable models of plant gas flux are feasible, but univariate models defining gas flux as a function of crop age are too simplistic. Multivariate models using CO2 and crop age were fit for PS(sub n), and R(sub d) by multiple regression. In each case, the selected model is a subset of a full third order model with all possible interactions. These models are improvements over the univariate models because they incorporate more than the single factor, crop age, as the primary variable governing gas flux. They are still limited, however, by their reliance on the other environmental conditions under which the original data were collected. Three-dimensional plots representing the response surface of each model are included. Suitability of using empirical models to generate engineering design estimates is discussed. Recommendations for the use of more complex multivariate models to increase versatility are included.

Cornett, Jessie David↗
NASA NTRS1971

Minimal logic block encoder Patent

Encoders designed to generate comma free biorthogonal Reed-Muller type code comprising conversion of 64 6-bit words into 64 32-bit data for communication purposes

Duffy, J. O.↗
NASA NTRS1972

Survey of aircraft electrical power systems

Areas investigated include: (1) load analysis; (2) power distribution, conversion techniques and generation; (3) design criteria and performance capabilities of hydraulic and pneumatic systems; (4) system control and protection methods; (5) component and heat transfer systems cooling; and (6) electrical system reliability.

Lee, C. H.↗
NASA NTRS1972

Single-stage experimental evaluation of compressor blading with slots and vortex generators, part 5

An experimental investigation was conducted to determine the extent that slots and vortex generators can increase the efficiency and stable operating range of highly loaded compressor stages. With slots in the rotor and stator, the stage performance both with and without vortex generators was inferior to that achieved with the unslotted blading. However, with vortex generators, stator slots, and an unslotted rotor, the stable operating range increased 25% and the stage peak efficiency increased 2.1% over the values achieved with the unslotted rotor and stator without vortex generators, at design equivalent rotor speed.

Brent, J. A.↗