Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GUIDANCE SENSOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Automated vehicle guidance using discrete reference markers

Techniques for providing steering control for an automated vehicle using discrete reference markers fixed to the road surface are investigated analytically. Either optical or magnetic approaches can be used for the sensor, which generates a measurement of the lateral offset of the vehicle path at each marker to form the basic data for steering control. Possible mechanizations of sensor and controller are outlined. Techniques for handling certain anomalous conditions, such as a missing marker, or loss of acquisition, and special maneuvers, such as u-turns and switching, are briefly discussed. A general analysis of the vehicle dynamics and the discrete control system is presented using the state variable formulation. Noise in both the sensor measurement and in the steering servo are accounted for. An optimal controller is simulated on a general purpose computer, and the resulting plots of vehicle path are presented. Parameters representing a small multipassenger tram were selected, and the simulation runs show response to an erroneous sensor measurement and acquisition following large initial path errors.

Johnston, A. R.↗
DOE OSTI2011

Healthcare Energy Efficiency Research and Development

Hospitals are known to be among the most energy intensive commercial buildings in California. Estimates of energy end-uses (e.g. for heating, cooling, lighting, etc.) in hospitals are uncertain for lack of information about hospital-specific mechanical system operations and process loads. Lawrence Berkeley National Laboratory developed and demonstrated a benchmarking system designed specifically for hospitals. Version 1.0 featured metrics to assess energy performance for the broad variety of ventilation and thermal systems that are present in California hospitals. It required moderate to extensive sub-metering or supplemental monitoring. In this new project, we developed a companion handbook with detailed equations that can be used toconvert data from energy and other sensors that may be added to or already part of hospital heating, ventilation and cooling systems into metrics described in the benchmarking document.This report additionally includes a case study and guidance on including metering into designs for new hospitals, renovations and retrofits. Despite widespread concern that this end-use is large and growing, there is limited reliable information about energy use by distributed medical equipment and other miscellaneouselectrical loads in hospitals. This report proposes a framework for quantifying aggregate energy use of medical equipment and miscellaneous loads. Novel approaches are suggested and tried in an attempt to obtain data to support this framework.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1990

Improving system reliability through formal analysis and use of checks in software

Software is playing increasingly important roles in avionics systems. It is widely used in navigation and, in some cases, in control loops that maintain aircraft stability. To guarantee the safety of flight systems, the FAA requires that critical components have a probability of failure no greater than 10(exp -9) per hour of flight. Software is being used to diagnose system components for failure. SIFT (Software Implemented Fault Tolerance) was a computer system developed to study the use of software to check for failure and manage processor reconfiguration. To guarantee that software satisfies its specifications, formal verification can be used. With this a program and its specification are viewed as mathematical objects, and a mathematical proof is used to show that the program and its specification are equivalent. In previous research, a theory of checking was developed to offer assistance in analyzing specifications and designing run-time checks. In the theory, checking is considered abstractly in terms of n-ary relations much like those of relational database theory. Within the theory check are categorized, checks on input and checks on results are considered, and formal attention is given to the minimization and logical combination of checks. The focus is upon input checks and the obstacles in checking input to critical systems. A central concern is with a property referred to as independence. The concern is with circumstances under which it is possible to apply isolated, independent checks to separate sensor inputs and be assure that all illegal input will be properly detected. Presently, independence is being investigated and checked in the context of the GCS (Guidance and Control System). The GCS simulator is intended for testing software that implements control laws for landing spacecraft. The large number of inputs and their complex interrelationships provide an exciting context in which to investigate independence and the difficulties of supplying input checks.

Staknis, Mark E.↗
NASA NTRS2017

DANTi: Detect and Avoid iN The Cockpit

Mid-air collision risk continues to be a concern for manned aircraft operations, especially near busy non-towered airports. The use of Detect and Avoid (DAA) technologies and draft standards developed for unmanned aircraft systems (UAS), either alone or in combination with other collision avoidance technologies, may be useful in mitigating this collision risk for manned aircraft. This paper describes a NASA research effort known as DANTi (DAA iN The Cockpit), including the initial development of the concept of use, a software prototype, and results from initial flight tests conducted with this prototype. The prototype used a single Automatic Dependent Surveillance - Broadcast (ADS-B) traffic sensor and the own aircraft's position, track, heading and air data information, along with NASA-developed DAA software to display traffic alerts and maneuver guidance to manned aircraft pilots on a portable tablet device. Initial flight tests with the prototype showed a successful DANTi proof-of-concept, but also demonstrated that the traffic separation parameter set specified in the RTCA SC-228 Phase I DAA MOPS may generate excessive false alerts during traffic pattern operations. Several parameter sets with smaller separation values were also tested in flight, one of which yielded more timely alerts for the maneuvers tested. Results from this study may further inform future DANTi efforts as well as Phase II DAA MOPS development.

Chamberlain, James↗
NASA NTRS1990

Automated terminal guidance for a Shuttle rendezvous to Space Station Freedom

An automated terminal guidance for a Shuttle rendezvous based on the Clohessy-Wiltshire (CW) linear equations of relative motion is described. The algorithm guides the Shuttle from the last rendezvous midcourse maneuver (MC4) through docking with Space Station Freedom (SSF). The uniqueness of this algorithm is that it makes it possible to use the CW equations to fly a line-of-sight (LOS) Vbar or Rbar in the final-approach docking phase. The algorithm is made of two parts, in and out-of-plane, and can also be used for station keeping during final approaches. Simulation results of the guidance integrated with the Shuttle's flight control system in the Systems Engineering Simulator (SES) at NASA Johnson are discussed. Plans to add a laser radar docking sensor to the SES and integrate it with the Shuttle's rendezvous navigation are examined.

Olszewski, Oscar W.↗
NASA NTRS2015

Flight Testing ALHAT Precision Landing Technologies Integrated Onboard the Morpheus Rocket Vehicle

A suite of prototype sensors, software, and avionics developed within the NASA Autonomous precision Landing and Hazard Avoidance Technology (ALHAT) project were terrestrially demonstrated onboard the NASA Morpheus rocket-propelled Vertical Testbed (VTB) in 2014. The sensors included a LIDAR-based Hazard Detection System (HDS), a Navigation Doppler LIDAR (NDL) velocimeter, and a long-range Laser Altimeter (LAlt) that enable autonomous and safe precision landing of robotic or human vehicles on solid solar system bodies under varying terrain lighting conditions. The flight test campaign with the Morpheus vehicle involved a detailed integration and functional verification process, followed by tether testing and six successful free flights, including one night flight. The ALHAT sensor measurements were integrated into a common navigation solution through a specialized ALHAT Navigation filter that was employed in closed-loop flight testing within the Morpheus Guidance, Navigation and Control (GN&C) subsystem. Flight testing on Morpheus utilized ALHAT for safe landing site identification and ranking, followed by precise surface-relative navigation to the selected landing site. The successful autonomous, closed-loop flight demonstrations of the prototype ALHAT system have laid the foundation for the infusion of safe, precision landing capabilities into future planetary exploration missions.

Carson, John M. III↗
NASA NTRS2019

A Detect and Avoid System in the Context of Multiple-Unmanned Aircraft Systems Operations

NASA's Unmanned Aircraft Systems Integration into the National Airspace System (UAS in the NAS) project examines the technical barriers associated with the operation of UAS in civil airspace. For UAS, the removal of the pilot from onboard the aircraft has eliminated the ability of the ground-based pilot in command (PIC) to use out-the-window visual information to make judgements about a potential threat of a loss of well clear with another aircraft. NASA's Phase 1 research supported the development of a Detect and Avoid (DAA) system that supports the ground-based pilot's ability to detect potential traffic conflicts and determine a resolution maneuver, but existing display/alerting requirements did not account for multiple UAS control (1:N). Demands for increased scalability of UAS in the NAS operations are expected to create a need for simultaneous control of UAs, and thus, a new DAA HMI design will likely be necessary. Previous research, however, has found performance degradations as the number of vehicles under operator control has increased. The purpose of the current human-in-the-loop (HITL) simulation was to examine the viability of 1:N operations with the Phase 1 DAA alerting and guidance. Sixteen UAS pilots flew three scenarios with varying number of UAs under their control (1:1, 1:3, 1:5). In addition to their supervisory and sensor mission responsibilities, pilots were to utilize the DAA system to remain DAA well clear (DWC) during scripted conflicts of mixed severity. Measured response times, separation performance, mission task data, and subjective feedback were collected to assess how the multi-UAS control configuration impacted pilots' ability to maintain DAA well clear and perform the mission tasks. Overall, the DAA system proved surprisingly adaptive to multi-UAS control for preventing losses of DAA well clear (LoDWC). The findings suggest that, while multi-UAS operators are able to maintain safe separation (DWC) from other traffic, their ability to efficiently perform missions drastically decreases with their number of controlled vehicles. Pilot feedback indicated that, for this context, the use of automation support tools for completing and managing mission tasks would be appropriate and desired, especially for ensuring efficient use of assets. Finally, human-machine interface (HMI) design considerations for multi-UAS operations are discussed.

Monk, Kevin J.↗
NASA NTRSDate not supplied

Mars Entry, Descent, and Landing Instrumentation 2 Trajectory, Aerodynamics, and Atmosphere Reconstruction

On February 18th, 2021, the Mars 2020 entry system successfully delivered the Perseverance rover to the surface of Mars at Jezero Crater. The entry capsule carried a set of instrumentation installed on the heat shield and backshell, named the Mars Entry, Descent, and Landing Instrumentation 2. The instruments include pressure transducers, thermocouples, heat flux gauges, and radiometers to measure the aerodynamic and aerothermodynamic performance of the entry vehicle. This paper describes the trajectory and atmosphere reconstruction results based on the pressure sensor measurements. The process uses a Kalman filter approach to estimate the freestream atmospheric properties from the pressure measurements combined with a model of the pressure distribution of the heatshield and other sensor inputs, including an inertial measurement unit and other on-board navigation sensors, and several external atmospheric observations. The results indicate upper altitude density was up to 150% higher than nominal, which is consistent with the observed early entry guidance start time. The density below 40 km was within 12% the pre-flight predictions. The reconstructed axial force coefficient was approximately 2% lower than the pre-flight prediction across the flight range.

Christopher D Karlgaard↗
NASA NTRS2022

Vision-Based Precision Approach and Landing for Advanced Air Mobility

Advanced Air Mobility (AAM) aircraft require perception systems for precision approach and landing systems (PALS) in urban, suburban, rural, and regional environments. The current state-of-the-art methods approved for automated approach and landing will be difficult to utilize in support of AAM operational concepts. However, there are technology and systems from other applications and lower-TRL research that use vision, IR, radar, and GPS methods to provide baseline perception and sensing requirements for AAM aircraft approach and landing. This paper focuses on vision-based PAL to demonstrate a closed-loop baseline controller while adhering to the Federal Aviation Administration requirements and regulations. The coplanar algorithm determines pose estimation, which feeds into an Extended Kalman filter. Combining IMU with vision creates a sensor fusion navigation solution for GPS-denied environments. The state estimate leads to glideslope and localizer error computations, which will be pertinent for designing and deriving guidance laws and control laws for AAM PALS. The IMU and vision navigation solution provides promising simulation results for AAM PALS, and higher fidelity simulations will include computer graphics rendering and feature correspondence.

Evan Kawamura↗
NASA NTRS1977

Airborne navigation system performance during RNAV/MLS transition

Aircraft position error sensitivity to sensor errors and flight path geometry is analyzed during RNAV/MLS transition using a digital computer simulation. The avionics sensitivity data provides information necessary to establish requirements for additional guidance law design and to establish airspace requirements for maneuvering to null out any residual RNAV errors upon MLS transition. The data base is also beneficial as planning information for subsequent flight testing. The parameters varied during the generation of the data base include flight profile, error source content and magnitude, ground facility location, runway/flight path orientation and navigation mode. The avionics, autopilots and aircraft dynamics correspond to the existing NASA Terminal Configured Vehicle. Significant transients were observed during MLS transition, primarily in the vertical channel. These transients have a significant impact on airspace requirements and operational procedures in the RNAV/MLS environment.

Heine, W.↗
NASA NTRS2017

The Generic Resolution Advisor and Conflict Evaluator (GRACE) for Unmanned Aircraft Detect-And-Avoid Systems

The paper describes the Generic Resolution Advisor and Conflict Evaluator (GRACE), a novel alerting and guidance algorithm that combines flexibility, robustness, and computational efficiency. GRACE is generic since it was designed without any assumptions regarding temporal or spatial scales, aircraft performance, or its sensor and communication systems. Therefore, GRACE was adopted as a core component of the Java Architecture for Detect-And-Avoid (DAA) Extensibility and Modeling, developed by NASA as a research and modeling tool for Unmanned Aerial Systems Integration in the National Airspace System (NAS). GRACE has been used in a number of real-time and fast-time experiments supporting evolving requirements of DAA research, including parametric studies, NAS-wide simulations, human-in-the-loop experiments, and live flight tests.

Unmanned Aircraft↗
DOE OSTI2021

ESS-DIVE Reporting Format for Hydrologic Monitoring Data and Metadata

The ESS-DIVE Reporting Format (RF) for Hydrologic Monitoring Data and Metadata was designed for water level, temperature, electrical conductivity, specific conductance, dissolved oxygen, and pH measured in situ using sensors deployed in water bodies. It can also be applied to a broader suite of variables beyond its original scope. The RF is intended to provide clear and easy guidance to data generators aiming to upload consistent findable, accessible, interoperable, and reusable (FAIR) datasets. The RF includes instructions (pdf), a term guide (csv), templates (csv and xlsx), and a list of recommended vocabulary (csv) to equip the data generator with all of the tools needed to successfully apply the RF. There is also a crosswalk to some key data resources and standards (csv). Users should cite this dataset when using the RF but are encouraged to access the RF files on GitHub (https://github.com/ess-dive-community/essdive-hydrologic-monitoring) where the RF documentation is maintained and updated on the ESS-DIVE Community Space GitHub. Questions and suggestions for improvement can be submitted as GitHub issues.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1987

Advanced fighter technology integration (AFTI)/F-16 Automated Maneuvering Attack System final flight test results

The AFTI F-16 Automated Maneuvering Attack System has undergone developmental and demonstration flight testing over a total of 347.3 flying hours in 237 sorties. The emphasis of this phase of the flight test program was on the development of automated guidance and control systems for air-to-air and air-to-ground weapons delivery, using a digital flight control system, dual avionics multiplex buses, an advanced FLIR sensor with laser ranger, integrated flight/fire-control software, advanced cockpit display and controls, and modified core Multinational Stage Improvement Program avionics.

Dowden, Donald J.↗
NASA NTRS1992

Flight evaluation of differential GPS aided inertial navigation systems

Algorithms are described for integration of Differential Global Positioning System (DGPS) data with Inertial Navigation System (INS) data to provide an integrated DGPS/INS navigation system. The objective is to establish the benefits that can be achieved through various levels of integration of DGPS with INS for precision navigation. An eight state Kalman filter integration was implemented in real-time on a twin turbo-prop transport aircraft to evaluate system performance during terminal approach and landing operations. A fully integrated DGPS/INS system is also presented which models accelerometer and rate-gyro measurement errors plus position, velocity, and attitude errors. The fully integrated system was implemented off-line using range-domain (seventeen-state) and position domain (fifteen-state) Kalman filters. Both filter integration approaches were evaluated using data collected during the flight test. Flight-test data consisted of measurements from a 5 channel Precision Code GPS receiver, a strap-down Inertial Navigation Unit (INU), and GPS satellite differential range corrections from a ground reference station. The aircraft was laser tracked to determine its true position. Results indicate that there is no significant improvement in positioning accuracy with the higher levels of DGPS/INS integration. All three systems provided high-frequency (e.g., 20 Hz) estimates of position and velocity. The fully integrated system provided estimates of inertial sensor errors which may be used to improve INS navigation accuracy should GPS become unavailable, and improved estimates of acceleration, attitude, and body rates which can be used for guidance and control. Precision Code DGPS/INS positioning accuracy (root-mean-square) was 1.0 m cross-track and 3.0 m vertical. (This AGARDograph was sponsored by the Guidance and Control Panel.)

Mcnally, B. David↗
NASA NTRS2008

Integrated Software Systems for Crew Management During Extravehicular Activity in Planetary Terrain Exploration

Initial planetary explorations with the Apollo program had a veritable ground support army monitoring the safety and health of the 12 astronauts who performed lunar surface extravehicular activities (EVAs). Given the distances involved, this will not be possible on Mars. A spacesuit for Mars must be smart enough to replace that army. The next generation suits can do so using 2 software systems serving as virtual companions, LEGACI (Life support, Exploration Guidance Algorithm and Consumable Interrogator) and VIOLET (Voice Initiated Operator for Life support and Exploration Tracking). The system presented in this study integrates data inputs from a suite of sensors into the MIII suit s communications, avionics and informatics hardware for distribution to remote managers and data analysis. If successful, the system has application not only for Mars but for nearer term missions to the Moon, and the next generation suits used on ISS as well. Field tests are conducted to assess capabilities for next generation spacesuits at Johnson Space Center (JSC) as well as the Mars and Lunar analog (Devon Island, Canada). LEGACI integrates data inputs from a suite of noninvasive biosensors in the suit and the astronaut (heart rate, suit inlet/outlet lcg temperature and flowrate, suit outlet gas and dewpoint temperature, pCO2, suit O2 pressure, state vector (accelerometry) and others). In the Integrated Walkback Suit Tests held at NASA-JSC and the HMP tests at Devon Island, communication and informatics capabilities were tested (including routing by satellite from the suit at Devon Island to JSC in Houston via secure servers at VCU in Richmond, VA). Results. The input from all the sensors enable LEGACI to compute multiple independent assessments of metabolic rate, from which a "best" met rate is chosen based on statistical methods. This rate can compute detailed information about the suit, crew and EVA performance using test-derived algorithms. VIOLET gives LEGACI voice activation capability, allowing the crew to query the suit, and receive feedback and alerts that will lead to corrective action. LEGACI and VIOLET can also automatically control the astronaut's cooling and consumable use rate without crew input if desired. These findings suggest that non-invasive physiological and environmental sensors supported with data analysis can allow for more effective management of mission task performance during EVA. Integrated remote and local view of data metrics allow crewmember to receive real time feedback in synch with mission control in preventing performance shortcomings for EVA in exploration missions.

Kuznetz, Lawrence↗
DOE OSTI2015

Robust electromagnetically guided endoscopic procedure using enhanced particle swarm optimization for multimodal information fusion

Purpose: Electromagnetically guided endoscopic procedure, which aims at accurately and robustly localizing the endoscope, involves multimodal sensory information during interventions. However, it still remains challenging in how to integrate these information for precise and stable endoscopic guidance. To tackle such a challenge, this paper proposes a new framework on the basis of an enhanced particle swarm optimization method to effectively fuse these information for accurate and continuous endoscope localization. Methods: The authors use the particle swarm optimization method, which is one of stochastic evolutionary computation algorithms, to effectively fuse the multimodal information including preoperative information (i.e., computed tomography images) as a frame of reference, endoscopic camera videos, and positional sensor measurements (i.e., electromagnetic sensor outputs). Since the evolutionary computation method usually limits its possible premature convergence and evolutionary factors, the authors introduce the current (endoscopic camera and electromagnetic sensor’s) observation to boost the particle swarm optimization and also adaptively update evolutionary parameters in accordance with spatial constraints and the current observation, resulting in advantageous performance in the enhanced algorithm. Results: The experimental results demonstrate that the authors’ proposed method provides a more accurate and robust endoscopic guidance framework than state-of-the-art methods. The average guidance accuracy of the authors’ framework was about 3.0 mm and 5.6° while the previous methods show at least 3.9 mm and 7.0°. The average position and orientation smoothness of their method was 1.0 mm and 1.6°, which is significantly better than the other methods at least with (2.0 mm and 2.6°). Additionally, the average visual quality of the endoscopic guidance was improved to 0.29. Conclusions: A robust electromagnetically guided endoscopy framework was proposed on the basis of an enhanced particle swarm optimization method with using the current observation information and adaptive evolutionary factors. The authors proposed framework greatly reduced the guidance errors from (4.3, 7.8) to (3.0 mm, 5.6°), compared to state-of-the-art methods.

60 APPLIED LIFE SCIENCES↗