Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRINDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

The influence of modifications of a fatigue loading history program on fatigue lifetime

Rectangular specimens of 7075 and 2014 aluminum alloys with two holes (stress concentration factor of 3.24) have been tested under axial fatigue loading on a six-rod test bed with modifications of the loading program, the surface particulars, and the frequency. The length of the precrack stage was investigated by use of a new crack detector. In most cases the two alloys behaved similarly, with similar life to crack start under the same loading. Some overloads lengthened the life. Truncation by omission of the lowest peak loads should be limited to about 20 percent of the ultimate load. Simplifying counting methods gave misleading results. Very thin surface layers of anodizing, protection by vinyl, dry nitrogen atmosphere, as well as stepwise reaming or grinding the surface of the holes, lengthened the life; thick anodized layers shortened the life. Compressing the hole surface by rolling had no influence. Frequencies at about 210 to 240 cpm produced shorter lives than those at 40 cpm. At 5.4 cpm the life was considerably longer. A model to better understand the precrack-stage fatigue mechanism is discussed.

Branger, J.↗

Formation of free radicals during mechanical degradation of elastomers.

Solithane 113 (an amorphous polyurethane elastomer) was prepared by curing equal proportions of castor oil and trifunctional isocyanate for 6 hr 45 min at 170 F. The sample material was mechanically degraded by grinding below and above its glass transition point at liquid nitrogen and room temperatures. The EPR spectra of ground samples were recorded and the number of free radicals were determined by a computer double-integration of the recorded spectra and by a comparison of the values with those of a standard material. Curves of EPR spectra suggest that different molecular mechanisms may be active in degradation of this material below and above its glass transition temperature.

Devries, K. L.↗

Development of high temperature fasteners using directionally solidified eutectic alloys

The suitability of the eutectics for high temperature fasteners was investigated. Material properties were determined as a function of temperature, and included shear parallel and perpendicular to the growth direction and torsion parallel to it. Techniques for fabricating typical fastener shapes included grinding, creep forming, and direct casting. Both lamellar Ni3Al-Ni3Nb and fibrous (Co,Cr,Al)-(Cr,Co)7C3 alloys showed promise as candidate materials for high temperature fastener applications. A brief evaluation of the performance of the best fabricated fastener design was made.

George, F. D.↗

Surface roughness effects on bidirectional reflectance

An experimental study of surface roughness effects on bidirectional reflectance of metallic surfaces is presented. A facility capable of irradiating a sample from normal to grazing incidence and recording plane of incidence bidirectional reflectance measurements was developed. Samples consisting of glass, aluminum alloy, and stainless steel materials were selected for examination. Samples were roughened using standard grinding techniques and coated with a radiatively opaque layer of pure aluminum. Mechanical surface roughness parameters, rms heights and rms slopes, evaluated from digitized surface profile measurements are less than 1.0 micrometers and 0.28, respectively. Rough surface specular, bidirectional, and directional reflectance measurements for selected values of polar angle of incidence and wavelength of incident energy within the spectral range of 1 to 14 micrometers are reported. The Beckmann bidirectional reflectance model is compared with reflectance measurements to establish its usefulness in describing the magnitude and spatial distribution of energy reflected from rough surfaces.

Smith, T. F.↗

CMB-13 research on carbon and graphite

The research on graphite and carbon for this period is reported. Topics discussed include: effects of grinding on the Santa Marie graphites, properties and purities of coal-tar, resin-bonded graphite, carbonization of resin components, and glass-like carbon filler.

Smith, M. C.↗

Preparation of pigments for space-stable thermal control coatings

The identification and control of vapor phase reaction kinetics to produce pigments by homogeneous nucleation were achieved. A vapor phase apparatus was designed, fabricated, and calibrated through 1800 C. Vapor phase reactions were analyzed, calculations made, and powders of alumina, rutile, zinc orthotitanate (in a mixed phase), calcium tungstate, and lanthana were produced by homogeneous nucleation. Electron microscopy shows uniform particle morphology and size, and supports anticipated advantages of vapor-phase homogeneous nucleation; namely, purity, freedom from defects, and uniform particle sizing without grinding.

Campbell, W. B.↗

Evaluation of feasibility of mapping seismically active faults in Alaska

The author has identified the following significant results. The Yukon-Tanana uplands north and east of Fairbanks appear, on ERTS-1 imagery, to be composed of a number of large-scale (approximately 100 kilometers square) crustal blocks. The boundaries of these blocks appear to be defined by a number of northeast-striking lineaments which form the major river valleys of the area. Principal among these are the valleys of the Salcha River, the Cehan River, and the Chatanika River. These lineaments are all seismically active, and are thus presumed to be faults. This parallel set of lineaments appears to be intersected at various angles by a secondary set of faults trending generally north to south. The larger earthquakes in the area occur at the intersections of the two sets. It appears that seismicity of this part of Alaska may be conceptually represented by the grinding together of rigid blocks, with earthquakes occurring along their common boundaries and at the intersections where three or more blocks come in contact.

Gedney, L. D.↗

Detection techniques for tenuous planetary atmospheres

The research performed during this period is reported. The studies discussed include: dust grinding and electrification, effects of metallic impurities on exoelectron emission, the connection between the charge acquired by the dust and the effect of the dust on human lung tissue. A list of publications generated by this research is included.

Hoenig, S. A.↗

Fabrication of cermet bearings for the control system of a high temperature lithium cooled nuclear reactor

The techniques used to fabricate cermet bearings for the fueled control drums of a liquid metal cooled reference-design reactor concept are presented. The bearings were designed for operation in lithium for as long as 5 years at temperatures to 1205 C. Two sets of bearings were fabricated from a hafnium carbide - 8-wt. % molybdenum - 2-wt. % niobium carbide cermet, and two sets were fabricated from a hafnium nitride - 10-wt. % tungsten cermet. Procedures were developed for synthesizing the material in high purity inert-atmosphere glove boxes to minimize oxygen content in order to enhance corrosion resistance. Techniques were developed for pressing cylindrical billets to conserve materials and to reduce machining requirements. Finishing was accomplished by a combination of diamond grinding, electrodischarge machining, and diamond lapping. Samples were characterized in respect to composition, impurity level, lattice parameter, microstructure and density.

Yacobucci, H. G.↗

A depth profile of C-14 in the lunar rock 12002.

The procedure involved separating the rock sample into depth fractions, designated OPI-OP6, grinding and dissolving each sample in a teflon still. The results obtained for the C-14 depth profile are shown in a table. The value for OP4 is unusually high. This phenomenon can be explained by leakage of atmospheric C-14 during the test. The profile shows a definite decrease in C-14 activity with increasing depth in the rock.

Boeckl, R. S.↗

Surface roughness effects on bidirectional reflectance.

An experimental study of surface roughness effects on bidirectional reflectance of metallic surfaces is presented. Samples consisting of glass, aluminum alloy, and stainless steel materials were roughened using standard grinding techniques and coated with a radiatively opaque layer of pure aluminum. Surface roughness parameters, rms height and rms slope, were evaluated from digitized surface profile measurements and are less than 1.0 micron, and 0.28, respectively. Rough-surface specular, bidirectional, and directional reflectance measurements for selected values of polar angle and wavelength of incident energy within the range from 10 to 80 deg and from 1 to 14 microns, respectively, are reported. The influence of surface roughness is discussed in terms of rms height and rms slope.

Smith, T. F.↗

Process to restore obliterated serial numbers on metal surfaces

Metal smeared into grooves of serial numbers by grinding or filing can be cleaned out by process called cavitation. Ultrasonic vibrator generates very high frequency vibrations in water which create millions of microscopic bubbles. Cavitation bubbles impact metal surface at thousands of pounds per square inch pressure. Metal particles filling grooves are broken away.

Young, S. G.↗

Method of making rolling element bearings

A method is described of making rolling elements by forming low mass cores having either hollow centers or being of a low mass material. The low mass cores are plated and heat treated to provide hard surfaces on the rolling elements. After grinding to the proper diameter the rolling elements are assembled between races to form a hearing.

Parker, R. J.↗

Rock sampling

A method for sampling rock and other brittle materials and for controlling resultant particle sizes is described. The method involves cutting grooves in the rock surface to provide a grouping of parallel ridges and subsequently machining the ridges to provide a powder specimen. The machining step may comprise milling, drilling, lathe cutting or the like; but a planing step is advantageous. Control of the particle size distribution is effected primarily by changing the height and width of these ridges. This control exceeds that obtainable by conventional grinding.

Blum, P.↗

Fabrication of an extreme ultraviolet glancing incidence telescope

A technique is described for use in the fabrication of glancing incidence telescopes which operate at large grazing angles (i.e., 8 to 15 degrees). Precision conic section plunge laps are used in a controlled grinding procedure to initially generate imaging surfaces which have a minimum of subsurface damage. A numerically controlled Moore Number 3 Measuring Machine is used throughout the fabrication procedure. Surface geometry accuracies on the order of one-tenth micron have been achieved.

Fleetwood, C. M.↗

Granulometric characteristics of lunar surface material from the Sea of Fertility

The particle size distributions in the 1-1000 micrometer range along the length of the core of lunar surface material returned by Luna 16 were recorded by electrical impulse as well as sieve methods. The measurements are represented in the form of cumulative functions of the logarithm of size versus the logarithm of particle number, and also as the logarithm of size versus particle mass on a probability scale. The former functions at all depths consist of the super-positioning of two straight lines with slopes from 2.10 to 4.05. The second functions are near linear, which together with the closeness of the calculated asymmetries of the distribution to zero and the nearness of the calculated excess of the distributions to unity indicate the closeness of the recorded distributions to the logarithmically normal law. This agrees with the assumption that regolith particles were formed in a process of intensive mechanical grinding.

Stakheyev, Y. I.↗

The generation of gravitational waves. I - Weak-field sources

This paper derives and summarizes a 'plug-in-and-grind' formalism for calculating the gravitational waves emitted by any system with weak internal gravitational fields. If the internal fields have negligible influence on the system's motions, the formalism reduces to standard 'linearized theory'. Independent of the effects of gravity on the motions, the formalism reduces to the standard 'quadrupole-moment formalism' if the motions are slow and internal stresses are weak. In the general case, the formalism expresses the radiation in terms of a retarded Green's function for slightly curved spacetime and breaks the Green's function integral into five easily understood pieces: direct radiation, produced directly by the motions of the source; whump radiation, produced by the 'gravitational stresses' of the source; transition radiation, produced by a time-changing time delay ('Shapiro effect') in the propagation of the nonradiative 1/r field of the source; focusing radiation, produced when one portion of the source focuses, in a time-dependent way, the nonradiative field of another portion of the source; and tail radiation, produced by 'back-scatter' of the nonradiative field in regions of focusing.

Thorne, K. S.↗

Microeconomic analysis of military aircraft bearing restoration

The risk and cost of a bearing restoration by grinding program was analyzed. A microeconomic impact analysis was performed. The annual cost savings to U.S. Army aviation is approximately $950,000.00 for three engines and three transmissions. The capital value over an indefinite life is approximately ten million dollars. The annual cost savings for U.S. Air Force engines are approximately $313,000.00 with a capital value of approximately 3.1 million dollars.

Hein, G. F.↗