Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FORCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Adhesion-force micro-scale study of desiccating granular material

Experiments on five-, four-, three- and two-wet-hydrophilic-grain clusters were performed to investigate evolution of adhesion of granular media during drying on the micro-scale. The experiments show that the adhesion-force of a cluster initially grows at most to three times the original value before decreasing to zero by the end of evaporation. The adhesion-force is composed of capillary pressure force acting over the liquid/solid contact surface area, and surface tension forces acting over the three-phase contact perimeter length. This is in contrast with most macro-scale phenomenological models, in which the only desaturation process variables affecting strength are suction and saturation. Both the contact surface area and contact perimeter length are reduced to zero upon complete liquid evaporation. The morphology of an evaporating water body evolves through slow flow controlled by evaporation rate, interrupted by various modes of fast air entry, which are non-equilibrium jumps of liquid/gas interfaces (Haines jumps). The instabilities involve large adhesion force discontinuities and substantial water mass reconfiguration with water flow in an extremely short time, which makes the process transient. The reconfigurations can reduce the original multi-grain water clusters to four-, three- and two-grain clusters by way of three different instability modes: of thin-sheet instability, or meniscus snap-through instability, depending on the sign of the Gauss curvature of the liquid surface, or finally, for two-grain bridges only, a liquid wire pinch-off. For larger meso-scale assemblies, however, the global adhesion-force evolution is little affected by the jumps. The air entries are potential sites for drying cracks. The (approximately) calculated capillary pressure for two- and three-grain clusters, in no cases is seen to reach high values, predicted from water retention curves.

Engineering↗

Description of the ARM Large-Scale Forcing Data from the Constrained Variational Analysis (VARANAL) Version 2

This technical report represents an update of the previous technical report written by Zhang et al., which described the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) user facility constrained variational analysis (VARANAL) that is used to develop the large-scale forcing data for driving single-column models (SCMs), cloud-resolving models (CRMs), and large-eddy simulation models (LES). The VARANAL algorithm was originally developed by Zhang and Lin and Zhang et al. at Stony Brook University and was migrated to the Lawrence Livermore National Laboratory (LLNL) as the ARM operational objective analysis system in May 1999. Since then, the algorithm has been evolved with time along with the availability of new observations and techniques to meet various modeling needs. Major updates include: 1. The method used to develop multi-year continuous forcing data, 2. The incorporation of eddy correlation flux measurement system (ECOR) turbulent fluxes into the analysis, and 3. Improvements to the workflow (e.g., implementing part of the code into the ARM Data Integrator [ADI]) to increase efficiency. The ARM large-scale forcing data have been widely used for SCM/CRM/LES to understand and improve physical processes in models. Zhang et al. has provided a comprehensive review of the SCM concept, early efforts to derive forcing data for SCM studies, efforts of the ARM constrained variational analysis, and previous SCM studies using ARM cases. This technical report focuses on the constrained variational analysis algorithm and the introduction of the ARM VARANAL products. We also extended the VARANAL algorithm into a three-dimensional constrained variational analysis (3DCVA) and designed an ensemble framework to address the forcing uncertainty. The 3D large-scale forcing data are released as another datastream named “varanal3d”. Please refer to the ARM varanal3d technical report for more information.

54 ENVIRONMENTAL SCIENCES↗

Simple and efficient algorithms for training machine learning potentials to force data

Machine learning models, trained on data from ab initio quantum simulations, are yielding molecular dynamics potentials with unprecedented accuracy. One limiting factor is the quantity of available training data, which can be expensive to obtain. A quantum simulation often provides all atomic forces, in addition to the total energy of the system. These forces provide much more information than the energy alone. It may appear that training a model to this large quantity of force data would introduce significant computational costs. Actually, training to all available force data should only be a few times more expensive than training to energies alone. Here, we present a new algorithm for efficient force training, and benchmark its accuracy by training to forces from real-world datasets for organic chemistry and bulk aluminum.

74 ATOMIC AND MOLECULAR PHYSICS↗

Unsupervised Learning Based Interaction Force Model for Nonspherical Particles in Incompressible Flows

This project provides a neural network-based interaction force model for gas-solid flows from low to intermediate Reynolds numbers and concentration, which can be linked to MFiX-DEM. We have constructed a database of the interaction force between the irregular-shaped particles using a spherical harmonic method and the fluid phase based on the particle-resolved direct numerical simulation (PR-DNS) with immersed boundary-based gas kinetic scheme. Unsupervised learning method, i.e., variational auto-encoder (VAE) has been applied to extract the primitive shape factors determining the drag force, lifting forces, and torque. The interaction force model has been trained and validated with a simple but effective multi-layer feed-forward neural network: multi-layer perceptron (MLP), which will be concatenated after the encoder of the previously trained VAE for geometry feature extraction for single, irregular particles. We have trained transpose convolutional neural networks with the PR-DNS data to predict the velocity and pressure gradient of the single particle systems and utilized them to calculate drag force of multi-particle systems. This model can provide high computational efficiency because it does not require collecting multiparticle system data from PR-DNS.

99 GENERAL AND MISCELLANEOUS↗

Machine-Learned Force Field Modeling of Metal Organic Frameworks for CO2 Direct Air Capture

To cope with legacy greenhouse gas emissions and to achieve net-zero emissions by 2050, the U.S. Department of Energy (DOE) is funding efforts to develop direct air capture (DAC), a method for removing CO2 directly from air. Metal organic frameworks (MOFs) have been well studied as DAC sorbent materials due to their tunable structural and compositional properties. Thermodynamic simulations using force fields are often used to provide predictions of a material’s performance in many separations. However, these force fields often make assumptions about bonds and the physics of the adsorption process. A new class of force fields called machine-learned force fields (MLFFs) use machine learning to form quantitative relationships between a material’s chemical structure and the forces and energies predicted by more accurate quantum mechanical calculations, such as dispersion-corrected density functional theory (DFT). In this work, models were developed to achieve DFT-level accuracy for the forces and energies associated with MOF flexibility and CO2 adsorption using MLFFs. These methods were parametrized based on thousands of DFT calculations of CO2 in flexible MOFs and used to predict MOF structural properties as well as CO2 adsorption in several MOFs.

Findley, John↗

Development of the ARM Lagrangian Large-Scale Forcing Data (ARMLAGTRAJ) Value-Added Product Based on the lagtraj Framework

The Atmospheric Radiation Measurement (ARM) large-scale forcing data developed based on the constrained variational analysis (VARANAL) value-added product (VAP) (Zhang and Lin 1997, Zhang et al. 2001, Xie et al. 2004, Tang et al. 2019) has been widely used for single-column models (SCMs), cloud-resolving models (CRMs), and large-eddy simulation models (LESs) to understand and improve physical processes in models. Recently, the U.S. Department of Energy (DOE) ARM user facility conducted several major field campaigns using ship-based moving observational platforms. For example, the Marine ARM GPCI Investigation of Clouds (MAGIC) field campaign focused on the role of subtropical marine-boundary layer (MBL) clouds, and the Multidisciplinary Drifting Observatory for the Study of Arctic Climate (MOSAiC) field campaign aimed to improve understanding of the coupled climate systems in the Arctic. Observations from moving platforms are critical to provide a comprehensive characterization of coupled-system processes associated with all stages of the cloud and/or sea-ice life cycle. Traditional ARM large-scale forcing data have been developed at fixed locations. They need to be extended to include these moving platforms to address data needs for ship-based field campaigns or to support LES modeling in a Lagrangian framework. With these considerations in mind, we develop ARM-type Lagrangian large-scale forcing data sets based on the lagtraj framework (Boeing et al. 2020) with notable enhancements in generating forcings that are more suitable for ARM field campaigns. The lagtraj is a novel tool that generates forcings for LES and SCM simulation in both Lagrangian and Eulerian perspective. This technical report focuses on the major changes we performed on the lagtraj algorithm and provides an overview of the ARM Lagrangian Large-Scale Forcing Data (ARMLAGTRAJ) value-added products.

54 ENVIRONMENTAL SCIENCES↗

Report of the Interagency Task Force on Carbon Capture and Storage

Carbon capture and storage (CCS) refers to a set of technologies that can greatly reduce carbon dioxide (CO{sub 2}) emissions from new and existing coal- and gas-fired power plants, industrial processes, and other stationary sources of CO{sub 2}. In its application to electricity generation, CCS could play an important role in achieving national and global greenhouse gas (GHG) reduction goals. However, widespread cost-effective deployment of CCS will occur only if the technology is commercially available and a supportive national policy framework is in place. In keeping with that objective, on February 3, 2010, President Obama established an Interagency Task Force on Carbon Capture and Storage composed of 14 Executive Departments and Federal Agencies. The Task Force, co-chaired by the Department of Energy (DOE) and the Environmental Protection Agency (EPA), was charged with proposing a plan to overcome the barriers to the widespread, cost-effective deployment of CCS within ten years, with a goal of bringing five to ten commercial demonstration projects online by 2016. Composed of more than 100 Federal employees, the Task Force examined challenges facing early CCS projects as well as factors that could inhibit widespread commercial deployment of CCS. In developing the findings and recommendations outlined in this report, the Task Force relied on published literature and individual input from more than 100 experts and stakeholders, as well as public comments submitted to the Task Force. The Task Force also held a large public meeting and several targeted stakeholder briefings. While CCS can be applied to a variety of stationary sources of CO{sub 2}, its application to coal-fired power plant emissions offers the greatest potential for GHG reductions. Coal has served as an important domestic source of reliable, affordable energy for decades, and the coal industry has provided stable and quality high-paying jobs for American workers. At the same time, coal-fired power plants are the largest contributor to U.S. greenhouse gas (GHG) emissions, and coal combustion accounts for 40 percent of global carbon dioxide (CO{sub 2}) emissions from the consumption of energy. EPA and Energy Information Administration (EIA) assessments of recent climate and energy legislative proposals show that, if available on a cost-effective basis, CCS can over time play a large role in reducing the overall cost of meeting domestic emissions reduction targets. By playing a leadership role in efforts to develop and deploy CCS technologies to reduce GHG emissions, the United States can preserve the option of using an affordable, abundant, and domestic energy resource, help improve national security, help to maximize production from existing oil fields through enhanced oil recovery (EOR), and assist in the creation of new technologies for export. While there are no insurmountable technological, legal, institutional, regulatory or other barriers that prevent CCS from playing a role in reducing GHG emissions, early CCS projects face economic challenges related to climate policy uncertainty, first-of-a-kind technology risks, and the current high cost of CCS relative to other technologies. Administration analyses of proposed climate change legislation suggest that CCS technologies will not be widely deployed in the next two decades absent financial incentives that supplement projected carbon prices. In addition to the challenges associated with cost, these projects will need to meet regulatory requirements that are currently under development. Long-standing regulatory programs are being adapted to meet the circumstances of CCS, but limited experience and institutional capacity at the Federal and State level may hinder implementation of CCS-specific requirements. Key legal issues, such as long-term liability and property rights, also need resolution. A climate policy designed to reduce our Nation's GHG emissions is the most important step for commercial deployment of low-carbon technologies such as CCS, because it will create a stable, long-term framework for private investments. A concerted effort to properly address financial, economic, technological, legal, institutional, and social barriers will enable CCS to be a viable climate change mitigation option that can over time play an important role in reducing the overall cost of meeting domestic and global emissions reduction targets. Federal and State agencies can use existing authorities and programs to begin addressing these barriers while ensuring appropriate safeguards are in place to protect the environment and public health and safety.

01 COAL, LIGNITE, AND PEAT↗

A Realistic Full-Scale 3D Modeling of Turning Using Coupled Smoothed Particle Hydrodynamics and Finite Element Method for Predicting Cutting Forces

Computational modelling is an effective technique for understanding the complex physics of machining. Large deformations, material separation, and high computational requirements are the key challenges faced while simulating machining. This work introduces a full-scale three-dimensional model of turning operations using a combined approach based on the Smoothed Particle Hydrodynamics (SPH) and Finite Element (FE) methods. By exploiting the advantages of each method, this approach leads to high-fidelity coupled SPH-FE machining models. Cutting forces and chip morphology are the primary results of interest. The machining models are validated with the results of turning experiments. Two-dimensional machining model underpredicts the cutting force and feed force by approximately 49% and 70%, respectively. Moreover, passive force cannot be predicted using the two-dimensional model. On the other hand, with the three-dimensional models developed in this manuscript, the difference between the total simulated force and experimentally measured force is ∼17%. The chip morphologies correlate with experiments in terms of the direction of the chip movement and the “long” continuous chips observed while turning Al 6061. This work expands the realm of machining simulations from two-dimensional orthogonal machining or sectional three-dimensional model to a full-scale realistic simulation. The encouraging simulation results show the potential to study more complex phenomena, such as machining stability and tool path modulation.

42 ENGINEERING↗

Prescribing the aerosol effective radiative forcing in the Simple Cloud-Resolving E3SM Atmosphere Model v1

Aerosol effective radiative forcing critically influences climate projections but remains poorly constrained. Using the Simple Cloud-Resolving E3SM Atmosphere Model (SCREAM) v1 configuration, we assess the sensitivity of the radiative forcing due to anthropogenic aerosol changes using a simplified prescribed aerosol scheme (SPA) derived from E3SM v3. Nudged simulations at 3 and 12 km horizontal grid spacings reveal a more negative aerosol forcing than the reference 100 km E3SM v3 whence the SPA properties are derived. The resulting globally averaged aerosol forcing signal is largely due to aerosol–cloud interactions and exhibits little overall resolution sensitivity, while hints of resolution sensitivity appear regionally between the 3 and 12 km runs. While the default SPA scheme overestimates cloud droplet dependence on aerosols, parameterization adjustments in the activation process reconcile forcing estimates with the reference model. Our results demonstrate the ability to use a prescribed aerosol scheme to hold aerosol forcing to a desired strength across resolutions.

54 ENVIRONMENTAL SCIENCES↗

Evaluating uncertainty in aerosol forcing of tropical precipitation shifts

Abstract. An observed southward shift in tropical rainfall over land between 1950 and 1985, followed by a weaker recovery post-1985, has been attributed to anthropogenic aerosol radiative forcing and cooling of the Northern Hemisphere relative to the Southern Hemisphere. We might therefore expect models that have a strong historic hemispheric contrast in aerosol forcing to simulate a further northward tropical rainfall shift in the near-term future when anthropogenic aerosol emission reductions will predominantly warm the Northern Hemisphere. We investigate this paradigm using a perturbed parameter ensemble (PPE) of transient coupled ocean–atmosphere climate simulations that span a range of aerosol radiative forcing comparable to multi-model studies. In the 20th century, in our single-model ensemble, we find no relationship between the magnitude of pre-industrial to 1975 inter-hemispheric anthropogenic aerosol radiative forcing and tropical precipitation shifts. Instead, tropical precipitation shifts are associated with major volcanic eruptions and are strongly affected by internal variability. However, we do find a relationship between the magnitude of pre-industrial to 2005 inter-hemispheric anthropogenic aerosol radiative forcing and future tropical precipitation shifts over 2006 to 2060 under scenario RCP8.5. Our results suggest that projections of tropical precipitation shifts will be improved by reducing aerosol radiative forcing uncertainty, but predictive gains may be offset by temporary shifts in tropical precipitation caused by future major volcanic eruptions.

54 ENVIRONMENTAL SCIENCES↗

The effects of spatial and temporal resolution of gridded meteorological forcing on watershed hydrological responses

Abstract. Meteorological forcing plays a critical role in accurately simulating the watershed hydrological cycle. With the advancement of high-performance computing and the development of integrated watershed models, simulating the watershed hydrological cycle at high temporal (hourly to daily) and spatial resolution (tens of meters) has become efficient and computationally affordable. These hyperresolution watershed models require high resolution of meteorological forcing as model input to ensure the fidelity and accuracy of simulated responses. In this study, we utilized the Advanced Terrestrial Simulator (ATS), an integrated watershed model, to simulate surface and subsurface flow and land surface processes using unstructured meshes at the Coal Creek Watershed near Crested Butte (Colorado). We compared simulated watershed hydrologic responses including streamflow and distributed variables such as evapotranspiration, snow water equivalent (SWE), and groundwater table driven by three publicly available, gridded meteorological forcings (GMFs) – Daily Surface Weather and Climatological Summaries (Daymet), the Parameter-elevation Regressions on Independent Slopes Model (PRISM), and the North American Land Data Assimilation System (NLDAS). By comparing various spatial resolutions (ranging from 400 m to 4 km) of PRISM, the simulated streamflow only becomes marginally worse when spatial resolution of meteorological forcing is coarsened to 4 km (or 30 % of the watershed area). However, the 4 km-resolution has much worse performance than finer resolution in spatially distributed variables such as SWE. Using the temporally disaggregated PRISM, we compared models forced by different temporal resolutions (hourly to daily), and sub-daily resolution preserves the dynamic watershed responses (e.g., diurnal fluctuation of streamflow) that are absent in results forced by daily resolution. Conversely, the simulated streamflow shows better performance using daily resolution compared to that using sub-daily resolution. Our findings suggest that the choice of GMF and its spatiotemporal resolution depends on the quantity of interest and its spatial and temporal scale, which may have important implications for model calibration and watershed management decisions.

54 ENVIRONMENTAL SCIENCES↗

Sensitivities of subgrid-scale physics schemes, meteorological forcing, and topographic radiation in atmosphere-through-bedrock integrated process models: a case study in the Upper Colorado River basin

Abstract. Mountain hydrology is controlled by interacting processes extending from the atmosphere through the bedrock. Integrated process models (IPMs), one of the main tools needed to interpret observations and refine conceptual models of the mountainous water cycle, require meteorological forcing that simulates the atmospheric process to predict hydroclimate then subsequently impacts surface–subsurface hydrology. Complex terrain and extreme spatial heterogeneity in mountainous environments drive uncertainty in several key considerations in IPM configurations and require further quantification and sensitivity analyses. Here, we present an IPM using the Weather Research and Forecasting (WRF) model which forces an integrated hydrologic model, ParFlow-CLM, implemented over a domain centered over the East River watershed (ERW), located in the Upper Colorado River basin (UCRB). The ERW is a heavily instrumented 300 km2 region in the headwaters of the UCRB near Crested Butte, CO, with a growing atmosphere-through-bedrock observation network. Through a series of experiments in the water year 2019 (WY19), we use four meteorological forcings derived from commonly used reanalysis datasets, three subgrid-scale physics scheme configurations in WRF, and two terrain shading options within WRF to test the relative importance of these experimental design choices for key hydrometeorological metrics including precipitation and snowpack, as well as evapotranspiration, groundwater storage, and discharge simulated by the ParFlow-CLM. Our hypothesis is that uncertainty from synoptic-scale forcings produces a much larger spread in surface–subsurface hydrologic fields than subgrid-scale physics scheme choice. Results reveal that the WRF subgrid-scale physics configuration leads to larger spatiotemporal variance in simulated hydrometeorological conditions, whereas variance across meteorological forcing with common subgrid-scale physics configurations is more spatiotemporally constrained. Despite reasonably simulating precipitation, a delay in simulated discharge peak is due to a systematic cold bias across WRF simulations, suggesting the need for bias correction. Discharge shows greater variance in response to the WRF simulations across subgrid-scale physics schemes (26 %) rather than meteorological forcing (6 %). The topographic radiation option has minor effects on the watershed-average hydrometeorological processes but adds profound spatial heterogeneity to local energy budgets (±30 W m−2 in shortwave radiation and 1 K air temperature differences in late summer). This is the first presentation of sensitivity analyses that provide support to help guide the scientific community to develop observational constraints on atmosphere-through-bedrock processes and their interactions.

54 ENVIRONMENTAL SCIENCES↗

Simulations of the quart (101-bar1)/water interface: A comparison of classical force fields, ab initi molecular dynamics, and x-ray reflectivity experiments.

Classical molecular dynamics (CMD) simulations of the (1011) surface of quartz interacting with bulk liquid water are performed using three different classical force fields, Lopes et al., ClayFF, and CHARMM water contact angle (CWCA), and compared to ab initio molecular dynamics (AIMD) and X-ray reflectivity (XR) results. The axial densities of the water and surface atoms normal to the surface are calculated and compared to previous XR experiments. Favorable agreement is shown for all the force fields with respect to the position of the water atoms. Analyses such as the radial distribution functions between water and hydroxyl atoms and the average cosine of the angle between the water dipole vector and the normal of the surface are also calculated for each force field. Significant differences are found between the different force fields from such analyses, indicating differing descriptions of the structured water in the near vicinity of the surface. AIMD simulations are also performed to obtain the water and hydroxyl structure for comparison among the predictions of the three classical force fields to better understand which force field is most accurate. It is shown that ClayFF exhibits the best agreement with the AIMD simulations for water hydroxyl radial distribution functions, suggesting that ClayFF treats the hydrogen bonding more accurately.

08 HYDROGEN↗

Forced Two-Phase Helium Cooling Scheme for the Mu2e Transport Solenoid

The Mu2e Transport Solenoid (TS) is an S-shaped magnet formed by two separate but similar magnets, TS-u and TS-d. Each magnet is quarter-toroid shaped with a centerline radius of approximately 3 m utilizing a helium cooling loop consisting of 25 to 27 horizontal-axis rings connected in series. This cooling loop configuration has been deemed adequate for cooling via forced single phase liquid helium; however it presents major challenges to forced two-phase flow such as “garden hose” pressure drop, concerns of flow separation from tube walls, difficulty of calculation, etc. Even with these disadvantages, forced two-phase flow has certain inherent advantages which make it a more attractive option than forced single phase flow. It is for this reason that the use of forced two-phase flow was studied for the TS magnets. This paper will describe the analysis using helium-specific pressure drop correlations, conservative engineering approach, helium properties calculated and updated at over fifty points, and how the results compared with those in literature. Based on the findings, the use of forced-two phase helium is determined to be feasible for steady-state cooling of the TS solenoids

43 PARTICLE ACCELERATORS↗

Clamp force and alignment checking device

A check fixture measures a total clamp force applied by a welder device. The welder device includes a welding horn having a plurality of weld pads and welding anvil having a plurality of weld pads. The check fixture includes a base member operatively supporting a plurality of force sensors. The base member and the force sensors are received between the weld pads of the welding horn and the anvil pads of the welding anvil. Each force sensor is configured to measure an individual clamp force applied thereto by corresponding weld and anvil pads when the base member is received between the welding horn and the welding anvil and the welder device is in the clamped position. The individual clamp forces are used to determine whether the weld and/or anvil pads are worn or misaligned.

42 ENGINEERING↗

Effect of Solvent Composition on Non-DLVO Forces and Oriented Attachment of Zinc Oxide Nanoparticles

Oriented attachment (OA) occurs when nanoparticles in solution align their crystallographic axes prior to colliding and subsequently fuse into single crystals. Traditional colloidal theories such as DLVO provide a framework for evaluating OA but fail to capture key particle interactions due to the atomistic details of both the crystal structure and the interfacial solution structure. Using zinc oxide as a model system, we investigated the effect of the solvent on short-ranged and long-ranged particle interactions and the resulting OA mechanism. In situ TEM imaging showed that ZnO nanocrystals in toluene undergo long-range attraction comparable to 1kT at separations of 10 nm and 3kT near particle contact. These observations were rationalized by considering non-DLVO interactions, namely dipole-dipole forces and torques between the polar ZnO nanocrystals. Langevin dynamics simulations showed stronger interactions in toluene compared to methanol solvents, consistent with the experimental results. Concurrently, we performed atomic force microscopy measurements using ZnO-coated probes for the short-ranged interaction. Our data provided valuable insights into another type of non-DLVO interaction, namely the repulsive solvation force. Specifically, the solvation force was stronger in water compared to ethanol and methanol, due to the stronger hydrogen bonding and denser packing of water molecules at the interface. In conclusion, our results highlight the importance of non-DLVO forces in a general framework for understanding and predicting particle aggregation and attachment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shell evolution and existence limit of exotic nuclei and the nuclear force

Novel simple properties of the monopole component of the effective nucleon-nucleon interaction are presented in the first half of this talk, leading to the so-called monopole-based universal interaction. Shell structures are shown to change as functions of N and Z consistently with experiments. Some key cases of this shell evolution are discussed, clarifying the effects of central and tensor forces. The validity of the present tensor force is examined in terms of the low-momentum interaction V{sub lowk} and the Q{sub box} formalism. In the second half of this talk, I discuss effects of the three-body force in exotic nuclei. The limit of neutron-rich nuclei, the neutron drip-line, evolves regularly from light to medium-mass nuclei except for a striking anomaly in the oxygen isotopes. This anomaly is not reproduced in shell-model calculations derived from microscopic two-nucleon forces. Here, we present the first microscopic explanation of the oxygen anomaly based on three-nucleon forces that have been established in few-body systems. This leads to repulsive contributions to the interactions among excess neutrons that change the location of the neutron drip-line from {sup 28}O to the experimentally observed {sup 24}O. Since the mechanism is robust and general, our findings impact the prediction of the most neutron-rich nuclei and the synthesis of heavy elements in neutron-rich environments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Improved in situ spring constant calibration for colloidal probe atomic force microscopy

In colloidal probe atomic force microscopy (AFM) surface forces cannot be measured without an accurate determination of the cantilever spring constant. The effective spring constant k depends upon the cantilever geometry and therefore should be measured in situ; additionally, k may be coupled to other measurement parameters. For example, colloidal probe AFM is frequently used to measure the slip length b at solid/liquid boundaries by comparing the measured hydrodynamic force with Vinogradova slip theory (V-theory). However, in this measurement k and b are coupled, hence, b cannot be accurately determined without knowing k to high precision. In this paper, a new in situ spring constant calibration method based upon the residuals, namely, the difference between experimental force-distance data and V-theory is presented and contrasted with two other popular spring constant determination methods. In this residuals calibration method, V-theory is fitted to the experimental force-distance data for a range of systematically varied spring constants where the only adjustable parameter in V-theory is the slip length b. The optimal spring constant k is that value where the residuals are symmetrically displaced about zero for all colloidal probe separations. This residual spring constant calibration method is demonstrated by studying three different liquids (n-decanol, n-hexadecane, and n-octane) and two different silane coated colloidal probe-silicon wafer systems (n-hexadecyltrichlorosilane and n-dodecyltrichlorosilane).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗