Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Experimental Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

The experimental verification of a streamline curvature numerical analysis method applied to the flow through an axial flow fan

The experimental verification of an inviscid, incompressible through-flow analysis method is presented. The primary component of this method is an axisymmetric streamline curvature technique which is used to compute the hub-to-tip flow field of a given turbomachine. To analyze the flow field in the blade-to-blade plane of the machine, the potential flow solution of an infinite cascade of airfoils is also computed using a source model technique. To verify the accuracy of such an analysis method an extensive experimental verification investigation was conducted using an axial flow research fan. Detailed surveys of the blade-free regions of the machine along with intra-blade surveys using rotating pressure sensing probes and blade surface static pressure taps provide a one-to-one relationship between measured and predicted data. The results of this investigation indicate the ability of this inviscid analysis method to predict the design flow field of the axial flow fan test rotor to within a few percent of the measured values.

Pierzga, M. J.↗

Structural damage detection of space truss structures using best achievable eigenvectors

A method is presented by which measured modes and frequencies from a modal test can be used to determine the location and magnitude of damage in a space struss structure. The damage is located by computing the Euclidean distances between the measured mode shapes and the best achievable eigenvectors. The best achievable eigenvectors are the projection of the measured mode shapes onto the subspace defined by the refined analytical model of the structure and the measured frequencies. Loss of both stiffness and mass properties can be located and quantified. To examine the performance of the method when experimentally measured modes are employed, various damage detection studies using a laboratory eight-bay truss structure were conducted. The method performs well even though the measurement errors inevitably make the damage location more difficult.

Lim, Tae W.↗

The momentum transfer of incompressible turbulent separated flow due to cavities with steps

An experimental study was conducted using a plate test bed having a turbulent boundary layer to determine the momentum transfer to the faces of step/cavity combinations on the plate. Experimental data were obtained from configurations including an isolated configuration and an array of blocks in tile patterns. A momentum transfer correlation model of pressure forces on an isolated step/cavity was developed with experimental results to relate flow and geometry parameters. Results of the experiments reveal that isolated step/cavity excrecences do not have a unique and unifying parameter group due in part to cavity depth effects and in part to width parameter scale effects. Drag predictions for tile patterns by a kinetic pressure empirical method predict experimental results well. Trends were not, however, predicted by a method of variable roughness density phenomenology.

White, R. E.↗

Practical model reduction for flexible structures

The most accepted methods for developing models of flexible structures for the analysis, design and simulation of control systems are finite element methods and extraction from experimental data. Using either of these methods, models are often produced with modes that do not significantly add to the fidelity of the model. This paper presents techniques for eliminating these modes. Particular attention is paid to multiple-input, multiple-output systems. First, control system models developed for flexible structures, using finite element methods and experimental data, are briefly discussed. the shortcomings of using models with unnecessary and/or residual modes are delineated. Then, two techniques for reducing the order of models are presented; the first is applicable to single-input, single-output systems and the second for multiple-input, multiple-output systems. Finally, both are illustrated using model data from the proposed NASA Shuttle-C.

Mitchell, Jerrel R.↗

Probabilistic Multi-Factor Interaction Model for Complex Material Behavior

Complex material behavior is represented by a single equation of product form to account for interaction among the various factors. The factors are selected by the physics of the problem and the environment that the model is to represent. For example, different factors will be required for each to represent temperature, moisture, erosion, corrosion, etc. It is important that the equation represent the physics of the behavior in its entirety accurately. The Multi-Factor Interaction Model (MFIM) is used to evaluate the divot weight (foam weight ejected) from the external launch tanks. The multi-factor has sufficient degrees of freedom to evaluate a large number of factors that may contribute to the divot ejection. It also accommodates all interactions by its product form. Each factor has an exponent that satisfies only two points - the initial and final points. The exponent describes a monotonic path from the initial condition to the final. The exponent values are selected so that the described path makes sense in the absence of experimental data. In the present investigation, the data used were obtained by testing simulated specimens in launching conditions. Results show that the MFIM is an effective method of describing the divot weight ejected under the conditions investigated. The problem lies in how to represent the divot weight with a single equation. A unique solution to this problem is a multi-factor equation of product form. Each factor is of the following form (1 xi/xf)ei, where xi is the initial value, usually at ambient conditions, xf the final value, and ei the exponent that makes the curve represented unimodal that meets the initial and final values. The exponents are either evaluated by test data or by technical judgment. A minor disadvantage may be the selection of exponents in the absence of any empirical data. This form has been used successfully in describing the foam ejected in simulated space environmental conditions. Seven factors were required to represent the ejected foam. The exponents were evaluated by least squares method from experimental data. The equation is used and it can represent multiple factors in other problems as well; for example, evaluation of fatigue life, creep life, fracture toughness, and structural fracture, as well as optimization functions. The software is rather simplistic. Required inputs are initial value, final value, and an exponent for each factor. The number of factors is open-ended. The value is updated as each factor is evaluated. If a factor goes to zero, the previous value is used in the evaluation.

Abumeri, Galib H.↗

Comparison of analytical and experimental subsonic steady and unsteady pressure distributions for a high-aspect-ratio-supercritical wing model with oscillating control surfaces

The results of a comparative study using the unsteady aerodynamic lifting surface theory, known as the Doublet Lattice method, and experimental subsonic steady- and unsteady-pressure measurements, are presented for a high-aspect-ratio supercritical wing model. Comparisons of pressure distributions due to wing angle of attack and control-surface deflections were made. In general, good correlation existed between experimental and theoretical data over most of the wing planform. The more significant deviations found between experimental and theoretical data were in the vicinity of control surfaces for both static and oscillatory control-surface deflections.

Mccain, W. E.↗

Estimating Pump Blockage

Blockage predicted for all components including inducers, impellers and diffusers. Pump performance predicted by semiempirical method shows excellent agreement with test results in Space Shuttle main-engine highpressure fuel turbopump. Comparisons of pump efficiency show equally good agreement of calculated values with experimental ones. Method improves current estimation methods based solely on subjective engineering judgment.

Chung, W.↗

A review of various flow-solid interaction analysis methods with emphasis on recent advances in turbulence models and flow analysis methods

A review on various experimental, analytical, and numerical methods for the flow-solid interaction of a nest of cylinders subjected to cross flow is presented in this paper. In order to assess the possibility of initiating a development of major numerical analysis method for flow-solid interaction of a nest of cylinders in cross flows, a review on various turbulence models, numerical methods such as the finite element method and the finite difference method, and the available numerical methods for flow-solid interactions have been included in this paper. A multiple-time-scale turbulence model for complex turbulent flows and a finite element method for high Reynolds number flows have been introduced herein for the same reason.

Kim, S.-W.↗

Analytical study of STOL Aircraft in ground effect. Part 1: Nonplanar, nonlinear wing/jet lifting surface method

A nonlinear, nonplanar three dimensional jet flap analysis, applicable to the ground effect problem, is presented. Lifting surface methodology is developed for a wing with arbitrary planform operating in an inviscid and incompressible fluid. The classical, infintely thin jet flap model is employed to simulate power induced effects. An iterative solution procedure is applied within the analysis to successively approximate the jet shape until a converged solution is obtained which closely satisfies jet and wing boundary conditions. Solution characteristics of the method are discussed and example results are presented for unpowered, basic powered and complex powered configurations. Comparisons between predictions of the present method and experimental measurements indicate that the improvement of the jet with the ground plane is important in the analyses of powered lift systems operating in ground proximity. Further development of the method is suggested in the areas of improved solution convergence, more realistic modeling of jet impingement and calculation efficiency enhancements.

Shollenberger, C. A.↗

Controls-structures interaction guest investigator program: Overview and phase 1 experimental results and future plans

The NASA Controls-Structures Interaction (CSI) Guest Investigator program is described in terms of its support of the development of CSI technologies. The program is based on the introduction of CSI researchers from industry and academia to available test facilities for experimental validation of technologies and methods. Phase 1 experimental results are reviewed with attention given to their use of the Mini-MAST test facility and the facility for the Advance Control Evaluation of Structures. Experiments were conducted regarding the following topics: collocated/noncollocated controllers, nonlinear math modeling, controller design, passive/active suspension systems design, and system identification and fault isolation. The results demonstrate that significantly enhanced performance from the control techniques can be achieved by integrating knowledge of the structural dynamics under consideration into the approaches.

Smith-Taylor, Rudeen↗

The Controls-Structures Interaction Guest Investigator Program - An overview and phase I experimental results

The NASA Controls-Structures Interaction (CSI) Guest Investigator program is described in terms of its support of the development of CSI technologies. The program is based on the introduction of CSI researchers from industry and academia to available test facilities for experimental validation of technologies and methods. Phase I experimental results are reviewed with attention given to their use of the Mini-MAST test facility and the facility for the Advance Control Evaluation of Structures. Experiments were conducted regarding: collocated/noncollocated controllers, nonlinear math modeling, controller design, passive/active suspension systems design, and system identification and fault isolation. The results demonstrate that significantly enhanced performance from the control techniques can be achieved by integrating knowledge of the structural dynamics under consideration into the approaches.

Smith-Taylor, Rudeen↗

Wake Geometry Measurements and Analytical Calculations on a Small-Scale Rotor Model

An experimental investigation was conducted in the Langley 14- by 22-Foot Subsonic Tunnel to quantify the rotor wake behind a scale model helicopter rotor in forward level flight at one thrust level. The rotor system in this test consisted of a four-bladed fully articulated hub with blades of rectangular planform and an NACA 0012 airfoil section. A laser light sheet, seeded with propylene glycol smoke, was used to visualize the vortex geometry in the flow in planes parallel and perpendicular to the free-stream flow. Quantitative measurements of wake geometric proper- ties, such as vortex location, vertical skew angle, and vortex particle void radius, were obtained as well as convective velocities for blade tip vortices. Comparisons were made between experimental data and four computational method predictions of experimental tip vortex locations, vortex vertical skew angles, and wake geometries. The results of these comparisons highlight difficulties of accurate wake geometry predictions.

Ghee, Terence A.↗

Sputtering of Surfaces by Ion Irradiation: A Comparison of Molecular Dynamics and Binary Collision Approximation Models to Laboratory Measurements

We compare various sputtering simulation methods to experimental results in both the low energy (<1 keV) and high energy (≥1 keV) impact regimes for argon ions impacting a pure copper substrate at normal incidence. Our results indicate that for high energy impacts, both binary collision approximation (BCA) and molecular dynamics methods can be used to generate reasonable predictions for the yield and energy distribution of the sputtered atoms. We also find reasonable agreement between the theoretical and experimental results down to impact energies of 600 eV. However, at 200 eV impact energies, significant discrepancies appear between the experimental and theoretical ejecta energy distributions in the peak position, the width of the energy distribution, and the magnitude of the high energy tail. These discrepancies appear to arise from the experimental results being only for atoms sputtered normal to the substrate surface, whereas the theoretical results are integrated over all 2π solid angles above the surface. Using the BCA code SDTrimSP and limiting the results to only atoms emitted within ±15° of the surface normal brings theory and experiment into reasonable agreement. These results suggest that for low energy impacts, the energy distribution of sputtered atoms is highly dependent on the emission angle of the ejecta.

Solar wind↗

Quadratic optimal cooperative control synthesis with flight control application

An optimal control-law synthesis approach is presented that involves simultaneous solution for two cooperating controllers operating in parallel. One controller's structure includes stochastic state estimation and linear feedback of the state estimates, while the other controller involves direct linear feedback of selected system output measurements. This structure is shown to be optimal under the constraint of linear feedback of system outputs in one controller. Furthermore, it is appropriate for flight control synthesis where the full-state optimal stochastic controller can be adjusted to be representative of an optimal control model of the human pilot in a stochastic regulation task. The method is experimentally verified in the case of the selection of pitch-damper gain for optimum pitch tracking, where optimum implies the best subjective pilot rating in the task. Finally, results from application of the method to synthesize a controller for a multivariable fighter aircraft are presented, and implications of the results of this method regarding the optimal plant dynamics for tracking are discussed.

Schmidt, D. K.↗

Thermodynamic analysis of turbulent combustion in a spark ignition engine. Experimental evidence

A method independent of physical modeling assumptions is presented to analyze high speed flame photography and cylinder pressure measurements from a transparent piston spark ignition research engine. The method involves defining characteristic quantities of the phenomena of flame propagation and combustion, and estimating their values from the experimental information. Using only the pressure information, the mass fraction curves are examined. An empirical burning law is presented which simulates such curves. Statistical data for the characteristics delay and burning angles which show that cycle to cycle fractional variations are of the same order of magnitude for both angles are discussed. The enflamed and burnt mass fractions are compared as are the rates of entrainment and burning.

Beretta, G. P.↗

An analytical study of the effect of coolant flow variables on the kinetic energy output of a cooled turbine blade flow

The results of an analytical study to determine the effect of changes in the amount, velocity, injection location, injection angle, and temperature of coolant flow on blade row performance are presented. The results show that the change in output of a cooled turbine blade row relative to the specific output of the uncooled blade row can be positive, negative, or zero. Comparisons between the analytical results and experimental results for four different cases of coolant discharge, all at a coolant temperature ratio of unity, show good agreement for three cases and rather poor agreement for the other. To further test the validity of the method, more experimental data is needed, particularly at different coolant temperature ratios.

Prust, H. W., Jr.↗

Progressive Damage Analysis of Post-Buckled Stiffened Panels under Static Compressive Loading

The validation of progressive damage analysis methods requires experimental data that captures the initiation of damage, its evolution with continued loading, and the morphology of damage throughout its evolution. In support of the NASA Advanced Composites Project, several validation specimens of increasing complexity have been tested and characterized in order to provide the data required to assess the capabilities of several progressive damage analysis methods for fiber-reinforced composite materials. The analytical capabilities of interest for this validation program include networks of interacting matrix cracks and delaminations in post-buckled stiffened structures. A series of single stringer compression specimens was tested and characterized at NASA Langley Research Center. The experimental data from these tests are compared with progressive damage finite element analysis results. Test/analysis comparisons are made in terms of load/displacement histories, damage morphology, and damage size versus load metrics.

Frank A Leone↗

On Blockage Corrections for Two-dimensional Wind Tunnel Tests Using the Wall-pressure Signature Method

The Wall-Pressure Signature Method for correcting low-speed wind tunnel data to free-air conditions has been revised and improved for two-dimensional tests of bluff bodies. The method uses experimentally measured tunnel wall pressures to approximately reconstruct the flow field about the body with potential sources and sinks. With the use of these sources and sinks, the measured drag and tunnel dynamic pressure are corrected for blockage effects. Good agreement is obtained with simpler methods for cases in which the blockage corrections were about 10% of the nominal drag values.

Allmaras, S. R.↗