Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Effect of annealing time, weight pressure and cobalt doping on the electrical and magnetic behavior of barium titanate

BaTi{sub 0.5}CO{sub 0.5}O{sub 3} (BTCO) nanoparticles were prepared by the solid state reaction technique using different starting materials and the microstructure examined by XRD, FESEM, BDS and VSM. X-ray diffraction and electron diffraction patterns showed that the nanoparticles were the tetragonal BTCO phase. The BTCO nanoparticles prepared from the starting materials of as prepared titanium-oxide, Cobalt -oxide and barium carbonate have spherical grain morphology, an average size of 65 nm and a fairly narrow size distribution. The nano-scale presence and the formation of the tetragonal perovskite phase as well as the crystallinity were detected using the mentioned techniques. Dielectric properties of the samples were measured at different frequencies. Broadband dielectric spectroscopy is applied to investigate the electrical properties of disordered perovskite-like ceramics in a wide temperature range. The doped BTCO samples exhibited low loss factor at 1 kHz and 1 MHz frequencies respectively.

36 MATERIALS SCIENCE↗

Characterization of a LaB6 tip as a thermionically enhanced photoemitter

There is a widespread interest in time-resolved electron spectroscopies such as ultrafast electron diffraction, ultrafast electron microscopy, and ultrafast electron energy loss spectroscopy. These techniques require pulsed electron beams with both high current and brightness. LaB6 is commonly used as a thermionic emitter because of its low work function and high electron yield. However, its use as a pulsed photocathode has not been widely explored. Here, we present measurements of the electron yield from a LaB6 filament exposed to 392 nm UV ultrafast laser pulses under a wide range of filament temperatures. We find that sample heating strongly enhances photoelectron yield, an effect known as thermionically enhanced photoemission. However, it also creates potentially undesirable, continuous thermionic background. We conclude that the ideal optimal operating conditions strongly depend on the type of measurement and require defining and quantifying an appropriate figure of merit.

Physics↗

Electron beam analysis induces Cl vacancy defects in a NaCl thin film

This work reports on the electron-induced modification of NaCl thin film grown on Ag(110). We show using low energy electron diffraction that electron beam bombardment leads to desorption and formation of Cl vacancy defects on NaCl surface. The topographic structure of these defects is studied using scanning tunneling microscopy (STM) showing the Cl defects as depressions on the NaCl surface. Most of the observed defects are mono-atomic vacancies and are located on flat NaCl terraces. Auger electron spectroscopy confirms the effect of electron exposure on NaCl thin films showing Cl atoms desorption from the surface. Using density functional theory taken into account the van der Waals dispersion interactions, we confirm the observed experimental STM measurements with STM simulation. Furthermore, comparing the adsorption of defect free NaCl and defective NaCl monolayer on Ag(110) surfaces, we found an increase of the adhesion energy and the charge transfer between the NaCl film and the substrate due to the Cl vacancy. In details, the adhesion energy increases between the NaCl film and the metallic Ag substrate from 30.4 meV Å –2 for the NaCl film without Cl vacancy and from 39.5 meV Å –2 for NaCl film with a single Cl vacancy. The charge transfer from the NaCl film to the Ag substrate is enhanced when the vacancy is created, from 0.63e – to 1.25e – .

Materials Science↗

Study of the crystal and electronic structure of graphene films grown on 6H-SiC (0001)

The structural, chemical, and electronic properties of epitaxial graphene films grown by thermal decomposition of the Si-face of a semi-insulating 6H-SiC substrate in an argon environment are studied by Raman spectroscopy, atomic-force microscopy, the low-energy electron diffraction method, X-ray photoelectron spectroscopy, angle-resolved photoemission spectroscopy and X-ray absorption spectroscopy at the carbon K edge. It is shown that the results of a systematic integrated study make it possible to optimize the growth parameters and develop a reliable technology for the growth of high-quality single-layer graphene films with a small fraction of bilayer graphene inclusions.

36 MATERIALS SCIENCE↗

Nature of Nano-Sized Plutonium Particles in Soils at the Hanford Site

The occurrence of plutonium dioxide (PuO2) either from direct deposition or from the precipitation of plutonium-bearing solutions in contaminated soils and sediments has been well described, particularly for the Hanford site in Washington State. However, past research has suggested that plutonium may exist in environmental samples at the Hanford site in chemical forms in addition to large size PuO2 particles and that these previously unidentified nano-sized particles maybe more reactive and thus more likely to influence the environmental mobility of Pu. Here we present evidence for the formation of nano-sized plutonium iron phosphate hydroxide structurally related to the rhabdophane group nanoparticles in 216-Z9 crib sediments from Hanford using transmission electron microscopy (TEM). The distribution and nature of these nanoparticles varied depending on the adjacent phases present. Fine electron probes were used to obtain electron diffraction and electron energy-loss spectra from specific phase regions of the 216-Z9 cribs specimens from fine-grained plutonium oxide and phosphate phases. Energy-loss spectra were used to evaluate the plutonium N4,5 (4d → 5f ) and iron L2,3 absorption edges. The iron plutonium phosphate formation may depend on the local micro-environment in the sediments, availability of phosphate, and hence the distribution of these minerals may control long-term migration of Pu in the soil. This study also points to the utility of using electron beam methods for determining the identity of actinide phases and their association with other sediment phases.

Cribs, Soil Contamination↗

Adhesion, friction, wear, and lubrication research by modern surface science techniques.

The field of surface science has undergone intense revitalization with the introduction of low-energy electron diffraction, Auger electron spectroscopy, ellipsometry, and other surface analytical techniques which have been sophisticated within the last decade. These developments have permitted submono- and monolayer structure analysis as well as chemical identification and quantitative analysis. The application of a number of these techniques to the solution of problems in the fields of friction, lubrication, and wear are examined in detail for the particular case of iron; and in general to illustrate how the accumulation of pure data will contribute toward the establishment of physiochemical concepts which are required to understand the mechanisms that are operational in friction systems. In the case of iron, LEED, Auger and microcontact studies have established that hydrogen and light-saturated organic vapors do not establish interfaces which prevent iron from welding, whereas oxygen and some oxygen and sulfur compounds do reduce welding as well as the coefficient of friction. Interpretation of these data suggests a mechanism of sulfur interaction in lubricating systems.

Keller, D. V., Jr.↗

Adsorption and condensation of Cu on W single-crystal surfaces

The adsorption and condensation of Cu up to several monolayers in thickness on tungsten 110 and 100 single-crystal surfaces are studied by combining low-energy electron diffraction, Auger electron spectroscopy, thermal desorption spectroscopy, work-function measurements, and quartz microbalance thickness measurements in one experimental system. The results show drastic differences in the evolution of the structure, work function, and desorption behavior between 110 and 100 surfaces. These differences are understandable in terms of the atomic roughness of the surfaces.

Bauer, E.↗

Structure and orientation of small particles of platinum deposited on NaCl and mica

The structure of small platinum particles condensed in vacuum onto NaCl (001), NaCl (111) and mica substrates was studied by electron diffraction and electron microscopy. Results show that above a certain substrate temperature decahedral or icosahedral particles are formed. These particles are practically absent with substrates cleaved in high vacuum. They are always much less numerous than in gold films prepared under the same conditions. Assumptions made to explain this phenomenon are: (1) the initial growth of an abnormal structure of the nuclei as opposed by the substrate; (2) the particles disappear before they attain a size which corresponds to the observations; and (3) the particles result from a coalescence mechanism leading to multiple twinned particles.

Renou, A.↗

Vapor phase diamond growth technology

Ion beam deposition chambers used for carbon film generation were designed and constructed. Features of the developed equipment include: (1) carbon ion energies down to approx. 50 eV; (2) in suit surface monitoring with HEED; (3) provision for flooding the surface with ultraviolet radiation; (4) infrared laser heating of substrate; (5) residual gas monitoring; (6) provision for several source gases, including diborane for doping studies; and (7) growth from either hydrocarbon source gases or from carbon/argon arc sources. Various analytical techniques for characterization of from carbon/argon arc sources. Various analytical techniques for characterization of the ion deposited carbon films used to establish the nature of the chemical bonding and crystallographic structure of the films are discussed. These include: H2204/HN03 etch; resistance measurements; hardness tests; Fourier transform infrared spectroscopy; scanning auger microscopy; electron spectroscopy for chemical analysis; electron diffraction and energy dispersive X-ray analysis; electron energy loss spectroscopy; density measurements; secondary ion mass spectroscopy; high energy electron diffraction; and electron spin resonance. Results of the tests are summarized.

Angus, J. C.↗

Surfaces

Techniques for the characterization of surface cleanliness and roughness for predicting the quality of an adhesive bond are outlined. Generally, smooth surfaces are only available from cleavage of crystalline materials along a natural cleavage plane. Films must be deposited on metal surfaces to achieve the same smoothness. Once the surfaces are clean, however, reaction with the ambient atmosphere becomes likely through diffusive and absorption processes, producing asperities. Electron diffraction, Auger electron, and X ray emission spectroscopy are used to characterize surface condition. Once the surface is observed to be clean, the application of an adhesive will usually prohibit separation along the adhesive; separation is then confined to the weaker of the two materials. Finally, the use of polytetrafluorothylene adhesive to test the adhesion between polymers and metal surfaces is described.

Buckley, D. H.↗

Transmission electron microscopic examination of phosphoric acid fuel cell components

Transmission electron microscopy (TEM) was used to physically characterize tested and untested phosphoric acid fuel cell (PAFC) components. Those examined included carbon-supported platinum catalysts, carbon backing paper, and Teflon-bonded catalyst layers at various stages of fabrication and after testing in pressurized PAFC's. Applicability of electron diffraction and electron energy loss spectroscopy for identifying the various phases was explored. The discussion focuses on the morphology and size distribution of platinum, the morphology and structural aspects of Teflon in catalyst layers, and the structural evidence of carbon corrosion. Reference is made to other physical characterization techniques where appropriate. A qualitative model of the catalyst layer that emerged from the TEM studies is presented.

Pebler, A.↗

Thermochemical Stability of Ca2Yb8(SiO4)6O2 Apatite in Presence of Molten Calcium-Magnesium-AluminoSilicate (CMAS)

Thermochemical stability of ytterbium silicon oxyapatite Ca 2 Yb 8 (SiO 4 ) 6 O 2 (CYbS) in the presence of molten calcium-magnesium aluminosilicate (CMAS) has been investigated at elevated temperatures. CYbS apatite powder was synthesized from the constituent oxides via solid state reaction method. Hot pressed apatite substrates were exposed to molten CMAS at 1200, 1300, and 1400 °C for 1, 10, and 50 h. Development of phases in the interaction region of the heat-treated specimens was monitored using scanning electron microscopy, transmission electron microscopy, high angle annular dark field imaging, selected area electron diffraction and energy dispersive X-ray spectroscopy. Monoclinic cyclosilicate Ca 3 Yb 2 (Si 3 O 9 ) 2 formed from interaction of CYbS apatite with CaO in the CMAS melt at the apatite-CMAS reaction front and continued to nucleate and grow within the residual CMAS in diffusion couples annealed for 1-50 h at 1200 °C and those heat treated at 1300 °C for 1 h. Residual CMAS was Ca-depleted when cyclosilicate was present. Dendritic wollastonite CaSiO 3 was observed within the residual CMAS in couples annealed at 1200 and 1300 °C. Ingress of molten CMAS, because of its exponential decrease in viscosity, occurred through open pores and along the grain boundaries of the apatite substrates without any detectable chemical reaction at 1300 and 1400 °C. Results of this study indicate that Ca 2 Yb 8 (SiO 4 ) 6 O 2 apatite has the potential to mitigate the CMAS corrosion up to about 1200 °C but not at higher temperatures.

X-ray diffraction↗

MICRO/NANO-STRUCTURAL EXAMINATION AND FISSION PRODUCT IDENTIFICATION IN NEUTRON IRRADIATED AGR-1 TRISO FUEL

Advanced microscopic and microanalysis techniques were developed and applied to study irradiation effects and fission product behavior in selected low-enriched uranium oxide/uranium carbide TRISO-coated particles from fuel compacts in six capsules irradiated to burnups of 11.2 to 19.6% FIMA. Although no TRISO coating failures were detected during the irradiation, the fraction of Ag-110m retained in individual particles often varied considerably within a single compact and at the capsule level. At the capsule level Ag-110m release fractions ranged from 1.2 to 38% and within a single compact, silver release from individual particles often spanned a range that extended from 100% retention to nearly 100% release. In this paper, selected irradiated particles from Baseline, Variant 1 and Variant 3 type fueled TRISO coated particles were examined using Scanning Electron Microscopy, Atom Probe Tomography; Electron Energy Loss Spectroscopy; Precession Electron Diffraction, Transmission Electron Microscopy, Scanning Transmission Electron Microscopy (STEM), High Resolution Electron Microscopy (HRTEM) examinations and Electron Probe Micro-Analyzer. Particle selection in this study allowed for comparison of the fission product distribution with Ag retention, fuel type and irradiation level. Nano sized Ag-containing features were predominantly identified in SiC grain boundaries and/or triple points in contrast with only two sitings of Ag inside a SiC grain in two different compacts (Baseline and Variant 3 fueled compacts). STEM and HRTEM analysis showed evidence of Ag and Pd co-existence in some cases and it was found that fission product precipitates can consist of multiple or single phases. STEM analysis also showed differences in precipitate compositions between Baseline and Variant 3 fuels. A higher density of fission product precipitate clusters were identified in the SiC layer in particles from the Variant 3 compact compared with the Variant 1 compact. Trend analysis shows precipitates were randomly distributed along the perimeter of the IPyC-SiC interlayer but only weakly associated with kernel protrusion and buffer fractures. There has been no evidence that the general release of silver is related to cracks or significant degradation of the microstructure. The results presented in this paper provide new insights to Ag transport mechanism(s) in intact SiC layer of TRISO coated particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Reflector Selection for the Indexing of Electron Backscatter Diffraction Patterns

Abstract We propose a new methodology for ranking the reflectors used in traditional Hough-based indexing of electron backscatter diffraction (EBSD) patterns. Instead of kinematic X-ray or electron structure factors ( F hkl ) currently utilized, we propose the integrated Kikuchi band intensity parameter ( β hkl ) based on integrated dynamical electron backscatter intensities. The proposed parameter is compared with the traditional kinematical intensity, $I_{hkl}^{{\rm kin}} $ , as well as the average Hough transform peak intensity, $I_{hkl}^{{\rm HSP}} $ and used to index EBSD patterns for a number of different material systems of varying unit cell complexities including nickel, silicon, rutile, and forsterite. For elemental structures, β hkl closely follows the kinematical ranking. However, significant ranking differences arise for more complex unit cells, with the β hkl parameter showing a better correlation with the integrated Hough intensities. Lastly, Hough-based indexing of a simulated forsterite data set showed an appreciable improvement in the median confidence index (0.15 to 0.35) when β hkl is used instead of $I_{hkl}^{{\rm kin}} $ for ranking the reflectors.

36 MATERIALS SCIENCE↗

Molecular beam epitaxial growth of BaTiO{sub 3} single crystal on Ge-on-Si(001) substrates

Thin films of perovskite type BaTiO{sub 3} (BTO) oxide have been grown epitaxially directly on Ge(001) surface at high temperature using molecular beam epitaxy. A stable (2x1) BaGe{sub x} surface periodicity is the critical enabling template for subsequent BTO heteroepitaxy on Ge(001). Reflection high energy electron diffraction (RHEED) and transmission electron microscopy indicate that high quality heteroepitaxy on Ge-on-Si(001) take place with <100>BTO(001)||<110>Ge(001) confirming a 45 deg. rotation epitaxial relationship. X-ray diffraction has been used to study the BTO lattice parameters and we evidenced that both tetragonal and cubic phases of BTO are present in the epilayer.

36 MATERIALS SCIENCE↗

Mapping 180° polar domains using electron backscatter diffraction and dynamical scattering simulations

A novel technique, which directly and nondestructively maps polar domains using electron backscatter diffraction (EBSD) is described and demonstrated. Through dynamical diffraction simulations and quantitative comparison to experimental EBSD patterns, the absolute orientation of a non-centrosymmetric crystal can be determined. With this information, the polar domains of a material can be mapped. The technique is demonstrated by mapping the non-ferroelastic, or 180°, ferroelectric domains in periodically poled LiNbO 3 single crystals. Furthermore, the authors demonstrate the possibility of mapping polarity using this technique in other polar materials system.

36 MATERIALS SCIENCE↗

A molecular dynamics study of laser-excited gold

The structural evolution of laser-excited systems of gold has previously been measured through ultrafast MeV electron diffraction. However, there has been a long-standing inability of atomistic simulations to provide a consistent picture of the melting process, leading to large discrepancies between the predicted threshold energy density for complete melting, as well as the transition between heterogeneous and homogeneous melting. We make use of two-temperature classical molecular dynamics simulations utilizing three highly successful interatomic potentials and reproduce electron diffraction data presented by Mo et al. [Science 360, 1451–1455 (2018)]. We recreate the experimental electron diffraction data, employing both a constant and temperature-dependent electron–ion equilibration rate. In all cases, we are able to match time-resolved electron diffraction data, and find consistency between atomistic simulations and experiments, only by allowing laser energy to be transported away from the interaction region. This additional energy-loss pathway, which scales strongly with laser fluence, we attribute to hot electrons leaving the target on a timescale commensurate with melting.

36 MATERIALS SCIENCE↗

Pseudo-Polymorphism in Layered FeS Intercalates: A Competition between Charged and Neutral Guest Species

Systematic synthesis studies of the formation of tetrahedral FeS-ethylenediamine intercalates resulted in the synthesis of a new compound, [Fe 9.4(2) S 10 ][Fe(en) 3 ] 0.6(1) ·en 0.9 ( 3 ). The composition and complex crystal structure were determined based on a synergistic combination of elemental composition, decomposition behavior, high-resolution synchrotron X-ray diffraction and total scattering, 57 Fe Mössbauer spectroscopy, and electron diffraction. The structural model was derived based on a systematic comparison to the previously reported structures [Fe 8 S 10 ][Fe(en) 3 ] 1 ·en 0.5 and tetragonal FeS. The new compound has flat Fe 9.4 S 10 layers, analogous to those in superconducting binary FeS. In the crystal structure of [Fe 9.4 S 10 ][Fe(en) 3 ] 0.6 ·en 0.9 , the interlayer space is occupied by [Fe(en) 3 ] 2+ complexes and neutral ethylenediamine molecules in a ~2:3 ratio. Interlayer species are not randomly oriented but ordered as evidenced by superstructural diffraction peaks in both high-resolution X-ray diffraction and electron diffraction patterns. Magnetic studies reveal no superconducting transition down to 2 K, indicating that the presence of minute amounts (~6%) of iron vacancies at the Fe-S layer in [Fe 9.4 S 10 ][Fe(en) 3 ] 0.6 ·en 0.9 is still sufficient to shift the position of the Fermi level resulting in an adjustment of the properties. Here, our work shows the importance of detailed characterization of the crystal structure of intercalated compounds to understand the origin of the observed properties and develop proper structure–property relationships.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗