Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPECTATION VALUE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The Effect of Radiation Damage on the Charge Collection Efficiency of Silicon Avalanche Photodiodes

Understanding radiation effects on avalanche photodiodes (APDs) is important because they are used in several applications involving harsh radiation environments. APDs are used as photosensors in applications where speed and detection efficiency are critical. Proton irradiation experiments on a commercial off-the-shelf APD demonstrated that the irradiation flux and applied reverse bias have a strong influence on the severity of radiation effects. This is measured using the ion beam induced charge (IBIC) technique in which charge collection efficiency (CCE) describes the signal response from a device. CCE can degrade substantially due to radiation damage, but recent measurements show that certain combinations of irradiation flux and reverse bias can lead to increases in CCE up to 186% ± 24% for irradiations with 2 MeV protons at a fluence of 6.4 × 10 11 cm –2 . This defect-enhanced charge multiplication (DECM) only appeared when the reverse bias during irradiation ranged from 170 to 1830 V out of a maximum operating bias of 2000 V and the proton flux ranged from 9.8 × 10 7 to 3.4 × 10 9 cm –2 s –1 . Furthermore values outside of either range led to losses in CCE. It is expected that DECM should be encountered in other devices, especially those with sufficiently high electric fields to cause impact ionization.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Patterns and controls on island‐wide aboveground biomass accumulation in second‐growth forests of Puerto Rico

Abstract Understanding the heterogeneity of biomass accumulation in second‐growth tropical forests following land use abandonment is important for informing ecosystem carbon models and forest restoration efforts. There is an urgent need for a broad sample of second‐growth forests to enhance our knowledge of carbon accumulation in human‐dominated landscapes, especially for older forests. Puerto Rico has predominantly second‐growth forests, ranging in age from approximately 25 to more than 80 years. We used an island‐wide sample of airborne lidar from the NASA Goddard Lidar, Hyperspectral, and Thermal (G‐LiHT) Airborne Imager collected on March 2017, forest inventory data, and data on forest age, precipitation, soils, and land use to estimate aboveground biomass stocks in moist and wet, second‐growth tropical forests. Biomass accumulation rates in Puerto Rico were lower, on average, than in other Neotropical forests. Median biomass across >16,700 ha of older second‐growth forests was 105 Mg ha −1 , and sampled biomass rarely surpassed 250 Mg ha −1 . Differences in biomass by age were large and persistent across different substrates and land uses, with a plateau in the pattern of island‐wide biomass accumulation after about 33 years. A spatial regression model showed that multiple factors were related to biomass accumulation, including time since abandonment, geologic substrate, past land use as coffee or pasture, precipitation, topographic wetness index, and slope. Our findings have important consequences for the total carbon storage and expected climate mitigation benefits of large‐scale reforestation efforts, and highlight the value of airborne lidar for quantifying biomass variability in complex tropical landscapes. Abstract in Spanish is available with online material.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

The functional roles of species in metacommunities, as revealed by metanetwork analyses of bird–plant frugivory networks

Abstract Understanding how biodiversity and interaction networks change across environmental gradients is a major challenge in ecology. We integrated metacommunity and metanetwork perspectives to test species’ functional roles in bird–plant frugivory interactions in a fragmented forest landscape in Southwest China, with consequences for seed dispersal. Availability of fruit resources both on and under trees created vertical feeding stratification for frugivorous birds. Bird–plant interactions involving birds feeding only on‐the‐tree or both on and under‐the‐tree (shared) had a higher centrality and contributed more to metanetwork organisation than interactions involving birds feeding only under‐the‐tree. Moreover, bird–plant interactions associated with large‐seeded plants disproportionately contributed to metanetwork organisation and centrality. Consequently, on‐the‐tree and shared birds contributed more to metanetwork organisation whereas under‐the‐tree birds were more involved in local processes. We would expect that species’ roles in the metanetwork will translate into different conservation values for maintaining functioning of seed‐dispersal networks.

Li, Hai‐Dong↗
DOE OSTI2023

Verwey transition as evolution from electronic nematicity to trimerons via electron-phonon coupling

Understanding the driving mechanisms behind metal-insulator transitions (MITs) is a critical step toward controlling material’s properties. Since the proposal of charge order–induced MIT in magnetite Fe 3 O 4 in 1939 by Verwey, the nature of the charge order and its role in the transition have remained elusive. Recently, a trimeron order was found in the low-temperature structure of Fe 3 O 4 ; however, the expected transition entropy change in forming trimeron is greater than the observed value, which arises a reexamination of the ground state in the high-temperature phase. Here, we use electron diffraction to unveil that a nematic charge order on particular Fe sites emerges in the high-temperature structure of bulk Fe 3 O 4 and that, upon cooling, a competitive intertwining of charge and lattice orders arouses the Verwey transition. Our findings discover an unconventional type of electronic nematicity in correlated materials and offer innovative insights into the transition mechanism in Fe 3 O 4 via the electron-phonon coupling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Quantifying conditional probabilities of fish-turbine encounters and impacts

Tidal turbines are one source of marine renewable energy but development of tidal power is hampered by uncertainties in fish-turbine interaction impacts. Current knowledge gaps exist in efforts to quantify risks, as empirical data and modeling studies have characterized components of fish approach and interaction with turbines, but a comprehensive model that quantifies conditional occurrence probabilities of fish approaching and then interacting with a turbine in sequential steps is lacking. We combined empirical acoustic density measurements of Pacific herring ( Clupea pallasii ) and when data limited, published probabilities in an impact probability model that includes approach, entrainment, interactions, and avoidance of fish with axial or cross-flow tidal turbines. Interaction impacts include fish collisions with stationary turbine components, blade strikes by rotating blades, and/or a collision followed by a blade strike. Impact probabilities for collision followed by a blade strike were lowest with estimates ranging from 0.0000242 to 0.0678, and highest for blade strike ranging from 0.000261 to 0.40. Maximum probabilities occurred for a cross-flow turbine at night with no active or passive avoidance. Estimates were lowest when probabilities were conditional on sequential events, and when active and passive avoidance was included for an axial-flow turbine during the day. As expected, conditional probabilities were typically lower than analogous independent events and literature values. Estimating impact probabilities for Pacific herring in Admiralty Inlet, Washington, United States for two device types illustrates utilization of existing data and simultaneously identifies data gaps needed to fully calculate empirical-based probabilities for any site-species combination.

collision risk↗
DOE OSTI2024

Technoeconomic Assessment of Phosphoric Acid and Rare Earth Element Recovery from Phosphoric Acid Sludge

Sustainability faces many challenges, including the availability of materials necessary for technological advancement. Rare earth elements (REEs), for example, are key materials for several manufacturing industries that can unlock renewable energy and sustainable development. In this study, a decanter centrifuge has been employed to successfully separated phosphoric acid and REE-containing particles from phosphoric acid sludge with concentrations ranging from 1000 to 2200 ppm REEs. Operating efficiently with up to 35 wt.% solids, the centrifuge was demonstrated to achieve approximately 95% phosphoric acid recovery and 90% REE recovery in a single pass, eliminating the need for additional processing steps. This breakthrough supports a proposed rare earth oxide (REO) recovery process integrating phosphoric acid (PA), elemental phosphorus (P4), and REO into two potential pathways: PA-REO and PA-P4-REO. These processes aim to reintroduce recovered phosphoric acid into the main product to significantly increase output and revenue. Post-separation, phosphorus-rich particles can be converted to P4, while REE-containing solids undergo further treatment including acid leaching, extraction/stripping, precipitation, and calcination to produce a marketable REO material. Technoeconomic analysis indicates promising profitability, with the PA-REO process showing a delta net present value (ΔNPV) of USD 441.8 million over a 12-year period and expected return within a year of construction, while the PA-P4-REO process yields a ΔNPV of USD 178.7 million over a 12-year return period. Both pathways offer robust financial prospects and demonstrate the feasibility of commercial-scale REO recovery from phosphoric acid sludge, offering an economically feasible approach to produce REEs for future sustainable development challenges related to sustainability.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The effect of temperature on photosystem II efficiency across plant functional types and climate

Modeling terrestrial gross primary productivity (GPP) is central to predicting the global carbon cycle. Much interest has been focused on the environmentally induced dynamics of photosystem energy partitioning and how improvements in the description of such dynamics assist the prediction of light reactions of photosynthesis and therefore GPP. The maximum quantum yield of photosystem II (Φ PSIImax ) is a key parameter of the light reactions that influence the electron transport rate needed for supporting the biochemical reactions of photosynthesis. Φ PSIImax is generally treated as a constant in biochemical photosynthetic models even though a constant Φ PSIImax is expected only for non-stressed plants. We synthesized reported Φ PSIImax values from pulse-amplitude-modulated fluorometry measurements in response to variable temperatures across the globe. We found that Φ PSIImax is strongly affected by prevailing temperature regimes with declined values in both hot and cold conditions. To understand the spatiotemporal variability in Φ PSIImax , we analyzed the temperature effect on Φ PSIImax across plant functional type (PFT) and habitat climatology. The analysis showed that temperature's impact on Φ PSIImax is shaped more by climate than by PFT for plants with broad latitudinal distributions or in regions with extreme temperature variability. There is a trade-off between the temperature range within which Φ PSIImax remains maximal and the overall rate of decline of Φ PSIImax outside the temperature range such that species cannot be simultaneously tolerant and resilient to extreme temperatures. Our study points to a quantitative approach for improving electron transport and photosynthetic productivity modeling under changing climates at regional and global scales.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

UN-SiC TRISO Post Irradiation Examination Developmental Work

As part of efforts to strengthen INL?s post irradiation analysis capabilities with non-Advanced Gas Reactor (AGR) tristructural isotropic (TRISO) fuels, two developmental activities were conducted. The first activity was to determine how best to analyze uranium nitride TRISO fuel kernels using electron probe microanalysis, while the second activity focused on developing a method to deconsolidate TRISO fuel particles that have been encased in a silicon carbide matrix. Because these two activities were unrelated, they have been presented separately in this report. Initial EPMA analyses showed nitrogen contents that far exceeded the concentration expected for UN--a line compound. Further examination showed that current literature values for the mass absorption coefficient (MAC) for the N ka X-ray absorbed by U ranged from approximately 1600 to 9500, with most values tending toward 9500. Measuring UN with five different progressively increasing accelerating voltages followed by using the modeling program xMAC suggests the actual MAC is approximately 2115. Additional MAC modifications were required to produce reasonable analytical results. Because of the inaccuracies of necessary MAC coefficients, UN analysis via scanning electron microscopy (SEM) is likely to produce inaccurate results. This is because SEM software does not typically allow the user to alter MACs. Tests have been performed to examine the feasibility of an electrochemical technique to liberate irradiated TRISO fuel from a SiC matrix without damaging the outer pyrolytic carbon layer of the fuel particle. The method is performed by electrochemically exposing the SiC to magnesium metal forming Mg2Si and C. Following exposure, the small SiC samples showed slight mass increases with no evidence of conversion to Mg2Si and C nor obvious degradation of the SiC samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Uncertainty-refined image segmentation under domain shift

Digital image segmentation is provided. The method comprises training a neural network for image segmentation with a labeled training dataset from a first domain, wherein a subset of nodes in the neural net are dropped out during training. The neural network receives image data from a second, different domain. A vector of N values that sum to 1 is calculated for each image element, wherein each value represents an image segmentation class. A label is assigned to each image element according to the class with the highest value in the vector. Multiple inferences are performed with active dropout layers for each image element, and an uncertainty value is generated for each image element. Uncertainty is resolved according to expected characteristics. The label of any image element with an uncertainty above a threshold is replaced with a new label corresponding to a segmentation class based on domain knowledge.

Martinez, Carianne↗
DOE OSTI2021

A Big Problem for Small Earthquakes: Benchmarking Routine Magnitudes and Conversion Relationships with Coda Envelope-Derived Mw in Southern Kansas and Northern Oklahoma

Earthquake magnitudes are widely relied upon measures of earthquake size. Although moment magnitude (M w ) has become the established standard for moderate and large earthquakes, difficulty in reliably measuring seismic moments for small (generally M w <4) earthquakes has meant that magnitudes for these events remain plagued by a patchwork of inconsistent measurement scales. Because of this, magnitudes of small earthquakes and statistics derived from them can be biased. Furthermore, because small earthquakes are much more numerous than large ones, many applications, such as seismic hazard modeling, depend critically on analysis of events characterized by magnitudes other than M w . Therefore, to assess this problem, we apply coda envelope analysis to reliably determine moment magnitudes for a case study of small earthquakes from northern Oklahoma and southern Kansas. Not surprisingly, we find significant differences among M L , m bLg , and M w for M ~2–4 earthquakes examined here. More troublingly, we find that relations designed to convert other magnitudes to M w , which are relied upon for important applications such as seismic hazard analysis, often increase rather than decrease this bias for our dataset. In our case study, we find that converted magnitudes can result in a systematic bias sometimes exceeding 0.5 magnitude units, a difference that typically corresponds to a factor of ~3 in seismicity rate. Moreover, we find a correspondingly large bias in Gutenberg–Richter b-values, controlled primarily by inaccurate magnitude scaling in the conversion relationships. Although this study focuses on a relatively small geographic area, we can expect that similar issues exist with varying severity in other regions. Therefore, magnitudes of small earthquakes and their associated statistics, including seismicity rates and b-values, should be treated with caution.

58 GEOSCIENCES↗
DOE OSTI2024

Identified charged-hadron production in 𝑝+Al, 3 He + Au, and Cu + Au collisions at $\sqrt{s_{NN}}$ = 200 GeV and in U + U collisions at $\sqrt{s_{NN}}$ = 193 GeV

The PHENIX experiment has performed a systematic study of identified charged-hadron (𝜋 ± , 𝐾 ± , 𝑝, $\bar{𝑝}$) production at midrapidity in 𝑝 + Al, 3 He + Au, and Cu + Au collisions at $\sqrt{s_{NN}}$ = 200 GeV and U + U collisions at $\sqrt{s_{NN}}$ = 193 GeV. Identified charged-hadron invariant transverse-momentum (𝑝 𝑇 ) and transverse-mass (𝑚 𝑇 ) spectra are presented and interpreted in terms of radially expanding thermalized systems. The particle ratios of 𝐾/𝜋 and 𝑝/𝜋 have been measured in different centrality ranges of large (Cu + Au and U + U) and small (𝑝 + Al and 3 He + Au) collision systems. The values of 𝐾/𝜋 ratios measured in all considered collision systems were found to be consistent with those measured in 𝑝+𝑝 collisions. However, the values of 𝑝/𝜋 ratios measured in large collision systems reach the values of ≈0.6, which is a factor of ≈2 larger than in 𝑝 + 𝑝 collisions. These results can be qualitatively understood in terms of the baryon enhancement expected from hadronization by recombination. Identified charged-hadron nuclear-modification factors (𝑅 𝐴⁢𝐵 ) are also presented. Enhancement of proton 𝑅 𝐴⁢𝐵 values over meson 𝑅 𝐴⁢𝐵 values was observed in central 3 He + Au, Cu + Au, and U + U collisions. Finally, the proton 𝑅 𝐴⁢𝐵 values measured in the 𝑝 + Al collision system were found to be consistent with 𝑅 𝐴⁢𝐵 values of 𝜙, 𝜋 ± , 𝐾 ± , and 𝜋 0 mesons, which may indicate that the size of the system produced in 𝑝 + Al collisions is too small for recombination to cause a noticeable increase in proton production.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Antideuterons and antihelium nuclei from annihilating dark matter

Recent studies of the cosmic-ray antiproton-to-proton ratio have identified an excess of ~10–20 GeV antiprotons relative to the predictions of standard astrophysical models. Intriguingly, the properties of this excess are consistent with the same range of dark matter models that can account for the long-standing excess of γ-rays observed from the Galactic Center. Such dark matter candidates can also produce significant fluxes of antideuterium and antihelium nuclei. In this work we study the production and transport of such particles, both from astrophysical processes as well as from dark matter annihilation. Importantly, in the case of AMS-02, we find that Alfvénic reacceleration (i.e., diffusion in momentum space) can boost the expected number of $\bar {\text d}$ and $^ {\text 3} \overline {\text {He}}$ events from annihilating dark matter by an order of magnitude or more. For relatively large values of the Alfvén speed, and for dark matter candidates that are capable of producing the antiproton and γ-ray excesses, we expect annihilations to produce a few antideuteron events and about one antihelium event in 6 yr of AMS-02 data. This is particularly interesting in light of recent reports from the AMS-02 Collaboration describing the detection of a number of antihelium candidate events.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Low-GWP Refrigerants Status and Outlook

Refrigeration - including air conditioning (AC) – contributes substantially to the modern life of the 21st century and its economy. The food cold chain, air conditioning, healthcare and energy are examples of sectors for which refrigeration is indispensable. About 5 billion refrigeration systems – of different types and sizes– operate worldwide in different applications [1]. The dominant share of equipment providing refrigeration operate on the vapor-compression-cycle principle and use fluorocarbon refrigerants. Concerns about the environmental safety have become the driving force for refrigerant changes within the last 35 years. The phased-out schedule of stratospheric-ozone-depleting fluids was first formulated by the Montreal Protocol (MP) in 1987 and was made more stringent during the follow-up international meetings [2]. The affected chlorofluorocarbon (CFC) and hydrochlorofluorocarbon (HCFC) refrigerants were largely replaced by hydrofluorocarbons (HFCs).The 2016 Kigali Amendment to the MP [3] responses to the concerns about the Earth climate change. The refrigeration and AC sectors are attributed with about 7.8 % of global greenhouse gas emissions [4]. This contribution comes in the form of direct effect, which is related to refrigerant emissions from refrigeration systems (37 %), and in the form of indirect effect, which is related to CO2 emissions from fossil fuel power plants producing electricity to power refrigeration systems (63 %) [4]. The Kigali Amendment aims at reducing the direct effect. The effect a given molecule has on the climate change is quantified in a simplified manner by its Global Warming Potential (GWP), a relative index referencing the effect produced to that of the same mass of carbon dioxide released to the atmosphere. By definition, GWP of carbon dioxide is equal to one.While HFC refrigerants have on average a lower GWP than the CFCs and HCFCs they replaced, they are still potent greenhouse gases (GHGs). The Kigali Amendment phases down the use of HFCs by imposing a schedule for reducing a weighted GWP value to be implemented by a country through the year 2047 (Figure 1). It provides four paths depending on the country location and category assigned in the MP, and also prescribes a method for establishing the baseline consumption used for calculating GWP reductions. For developing countries, it is expected to bring the weighed GWP across all refrigeration applications down to about 300 from the baseline value of about 2000. The implementation of Kigali Amendment aims at reducing the future warming due to HFCs from the range of 0.3 °C to 0.5 °C to less than 0.1 °C [5]. While this reduction may seem to be small, it must be viewed in the context of the 2015 Paris Agreement [6], which calls for holding global warming to well below 2 °C and pursuing to limit global warming to 1.5 °C relative to pre-industrial levels [6]. Considering that average global temperatures reached 1 °C above pre-industrial levels for the first time in 2015 [7], the Earth is already within 1 °C of the “2 °C limit”.The low-GWP requirement narrows the pool of fluids that can be considered for application as a refrigerant [8]. This Informatory Note discusses low-GWP refrigerant options for major applications and presents their selection merits.

Yana Motta, Samuel↗
DOE OSTI2022

Economic analysis of the benefits to petroleum refiners for low carbon boosted spark ignition biofuels

A refinery modeling framework is developed to estimate the benefits of blending high-quality biofuels directly with refinery gasoline components for attaining a premium grade fuel (also termed as Co-Optima Boosted SI gasoline here). Our results change the paradigm of bio-blendstocks (BBs) being competitors to fossil components, by identifying opportunities for refineries to add value to their product slate, from some favorable BB properties. This potential value can be characterized by calculating the breakeven value (BEV), as defined down below. The proposed modeling framework incorporates extensive data from (1) projected product over the next few decades, (2) crude oil and refinery products pricing, and (3) fuel specifications. The complete refinery models serve as a basis for assessing the value of biofuels, assuming profitability remains the same for representative petroleum refinery configurations. Our assessment showed wide range of variation of biofuels BEV from $\$$20-$\$$120/bbl, within the considered blending level and crude prices. Further, the BEV was correlated with the fuel octane ratings such as octane numbers (research, RON and motor octane numbers, MON) and both antiknock index (AKI, average of RON and MON) and sensitivity (S, difference between RON and MON), with a slightly higher correlation with the sensitivity. However, the expected decrease in gasoline demand for the upcoming years could negatively impact biofuels demand and value, in a business-as-usual scenario. Our analysis also showed a more valuable bio-blendstocks incorporation in smaller refineries since they can enhance the capabilities for producing specialty, high-value fuels/products, and introduce high octane-barrels into otherwise constrained blending operations. Additional implications towards refiners include opportunities to rebalance operations, access to high-value fuel markets, and synchronization with broader transportation industry trends. Furthermore, results indicate the value of Co-Optima boosted spark ignition (BSI) efficiency gains can extend to refiners to incentivize decarbonization and diversified feedstock production.

09 BIOMASS FUELS↗
DOE OSTI2026

Development of Advanced, Radiation Resistant, Optical-based Detector Technology for Future Experiments.

The primary objective of this project has been to advance the design of high-performance electromagnetic (EM) calorimeters for future particle physics experiments, to identify and measure the timing, position and energy of electrons, positrons and gamma rays, particularly in high-luminosity environments with intense radiation and pileup conditions. To meet such challenges, the proposed research has focused on the development of ultra-compact, radiation-hard calorimeter modules, to provide excellent timing, spatial, and energy resolution. The work aligns with the DOE’s Basic Research Needs (BRN) for High Energy Physics (HEP) Instrumentation and the research team contributes actively to the Coordinating Panel on Advanced Detectors (CPAD) RDC9 calorimetry collaboration in the USA and the European Committee on Future Accelerators (ECFA) DRD-CALO calorimetry collaboration at CERN, the European Laboratory for Particle Physics located in Geneva, Switzerland. The research builds on the RADiCAL (radiation-hard, ultra-compact) modular sampling calorimeter approach, developed by the research team, which employs dense and very bright optical materials such as LYSO:Ce scintillator plates that are interleaved with very dense tungsten plates to minimize detector size while optimizing performance. The modules are comparable in size to a human index finger, dimensionally 14 mm x 14 mm in cross section and 135 mm in length. And despite the small size, the structure is capable of providing excellent timing and energy resolution. This is facilitated through the use of specialized quartz capillaries filled with wavelength-shifting filaments, positioned at various depths along the length of a module, to collect and guide light signals to silicon photomultipliers (SiPMs) which detect and convert the optical signals to electronic signals for analysis. The primary goals of this project have been: (1) Achieve a timing resolution to σ t ≤ 30 ps for high-energy electrons and photons, important for their association with specific events produced in colliding-beam experiments and for the detection of decays-in-flight of long-lived particles. The project has achieved this goal in beam tests of a single RADiCAL module at CERN, during which a timing resolution of σ t = 27 ps was measured for electrons of energy E = 150 GeV. Based upon a mathematical fit to the data measured over a broad energy range from low energy to high energy, a resolution of σ t ≤ 18 ps has been estimated for electrons of very high (TeV) energy. From these measurements and with further expected technical improvements, the timing resolution should reach σ t ≤ 10 ps, important for searches for discovery physics in upcoming and future experiments. (2) Achieve an energy resolution of σ E / E ≤ 10% / $\sqrt{E}$. The project has yet to achieve this goal, but is close to it, having measured a value of σ E / E ≤ 15.9% / $\sqrt{E}$ using a modular array. Ultimately, the resolution goal is expected to be reached by adjustments to material thicknesses within the modules, which will improve the sampling fraction to measure more precisely the shower energy for lower energy particles. The versatility of the modular RADiCAL approach enables the testing of advanced materials, photosensors and electronics, developed in collaboration with CPAD RDC and ECFA DRD-CALO groups. The structure can distinguish electrons, positrons and gamma rays from hadrons and muons and beam-induced backgrounds, making it a valuable tool in a variety of detector environments, including future circular colliders (FCC-ee, FCC-hh) proposed for the European Laboratory for Particle Physics (CERN), the muon-collider proposed for Fermi National Accelerator Laboratory (Fermilab), and searches for new physics in beam-dump, fixed target and forward-physics experiments. And, while designed with particle physics applications in mind, the technologies developed in this project have the potential for application more broadly in particle and nuclear physics, materials science, and medical physics, underscoring the far-reaching potential of this line of instrumentation research and development.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Reactive flash sintering and characterization of bulk high entropy nitrides

Over the past decade, numerous high-entropy ceramics have been synthesized, often displaying attractive properties. However, the study on facile preparation of bulk high entropy nitrides (HEN) are limited, despite its broad potential applications. This research demonstrates for the first time rapid fabrication (within ∼6 min) of bulk high-entropy nitrides, especially (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N, from binary nitride powder mixtures using a highly efficient reactive flash sintering (RFS) technique. X-ray diffraction (XRD) shows the HENs from RFS are near single-phase solid solutions with a rock salt crystal structure, while in situ synchrotron study carried out during RFS captured in real time the formation of HEN, which was preserved upon cooling, suggesting thermodynamic stability of the HEN phase, even up to extreme pressure (∼35.6 GPa). Microscopic analyses using SEM, STEM, and EDS reveal decent uniformity for HEN with no obvious segregation of elements, even to submicron scale. Some properties of the obtained bulk HENs are consistent with expectations. For example, their hardness and bulk modulus are close to estimates based on rule-of-mixture (ROM) values from the constituent binary nitrides. Meanwhile, some other measured properties seem to show surprises. For example, the fracture toughness for the HENs (e.g., 7.81 ± 1.40 MPa•m 1/2 or higher) turns out to be more than double of the expected ROM estimates. The significantly improved fracture toughness is attributed to the observed nano-layered structure of the HENs, despite the HEN’s cubic crystal structure and high hardness. In addition, the oxidation resistance shows improvement up till ∼800°C, possibly due to Ta doping that suppress oxygen vacancy formation in the oxide shell, while the 5-metal HEN of (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N displays superconductivity (T c of ∼5–7 K from magnetism and resistivity measurements, slightly lower than ROM estimate), despite insulating property of starting AlN. Furthermore, future study combining experimental investigation using larger samples to confirm the observed increase in fracture toughness and oxidation resistance, theoretical modeling at different length scale, and more detailed structural/chemical characterization, especially at the atomic scale, are all needed to fully understand the inter-relationships between composition, processing, structure, and novel properties for these HENs and the development of related new materials for different applications.

Flash sintering↗
DOE OSTI2023

Direct comparison between experiments and dislocation dynamics simulations of high rate deformation of single crystal copper

A long standing challenge in computational materials science is to establish a quantitative connection between the macroscopic properties of plastic deformation with the microscopic mechanisms of dislocations in crystalline materials. Although the discrete dislocation dynamics (DDD) simulation method has been developed for several decades with the goal of addressing this challenge, a one-to-one comparison between the DDD predictions on single crystal stress–strain curves and experimental measurements under identical conditions has not been possible to date. Such a comparison is an essential step towards establishing a dislocation-physics based theory of plasticity and a multiscale framework of the plastic behaviors of crystalline materials. Here we provide direct comparisons between the stress–strain curves of Cu single crystals under high strain rate loading in the [0 0 1] and [0 1 1] directions obtained from miniaturized desktop Kolsky bar experiments and those from DDD simulations under identical loading conditions. With an appropriate set of parameters, DDD simulations can produce stress–strain curves that are in reasonable agreement with the experimental results. However, the dislocation mobility values needed to achieve this agreement are an order of magnitude lower than expected based on previous measurements and atomistic simulations. We hypothesize that this discrepancy could be caused by drag forces from jogs and point defects produced during the plastic deformation. Cross-slip of screw dislocations is also found to be necessary to capture the experimental stress–strain behavior, especially for the [0 1 1] loading direction. Finally, this work provides an example of how direct comparisons between DDD simulations and experimental measurements can provide new insight into the fundamental mechanisms of plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Using resonant energy X-ray diffraction to extract chemical order parameters in ternary semiconductors

II–IV–V 2 materials, ternary analogs to III–V materials, are emerging for their potential applications in devices such as LEDs and solar cells. Controlling cation ordering in II–IV–V 2 materials offers the potential to tune properties at nearly fixed compositions and lattice parameters. While tuning properties at a fixed lattice constant through ordering has the potential to be a powerful tool used in device fabrication, cation ordering also creates challenges with characterization and quantification of ordering. In this work, we investigate two different methods to quantify cation ordering in ZnGeP 2 thin films: a stretching parameter calculated from lattice constants , and an order parameter determined from the cation site occupancies ( S ). We use high resolution X-ray diffraction (HRXRD) to determine and resonant energy X-ray diffraction (REXD) to extract S . REXD is critical to distinguish between elements with similar Z -number ( e.g. Zn and Ge). We found that samples with a corresponding to the ordered chalcopyrite structure had only partially ordered S values. The optical absorption onset for these films occurred at lower energy than expected for fully ordered ZnGeP 2 , indicating that S is a more accurate descriptor of cation order than the stretching parameter. Since disorder is complex and can occur on many length scales, metrics for quantifying disorder should be chosen that most accurately reflect the physical properties of interest.

36 MATERIALS SCIENCE↗