Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELECTRODEPOSITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Non-gassing nickel-cadmium battery electrodes and cells

The concept of a negative limited nongassing nickel-cadmium battery was demonstrated by constructing and testing practical size experimental cells of approximately 25 Ah capacity. These batteries operated in a gas-free manner and had measured energy densities of 10-11 Wh/lb. Thirty cells were constructed for extensive testing. Some small cells were tested for over 200 cycles at 100% depth. For example, a small cell with an electrodeposited cadmium active mass on a silver screen still had 55% of its theoretical capacity (initial efficiency was 85%). There was no evidence of deterioration of gassing properties with cycling of the nickel electrodes. The charge temperature was observed to be the most critical variable governing nickel electrode gassing. This variable was shown to be age dependent. Four types of cadmium electrodes were tested: an electrodeposited cadmium active mass on a cadmium or silver substrate, a porous sintered silver substrate based electrode, and a Teflon bonded pressed cadmium electrode. The electrodeposited cadmium mass on a silver screen was found to be the best all-around electrode from a performance point of view and from the point of view of manufacturing them in a size required for a 25 Ah size battery.

Luksha, E.↗
NASA NTRS1982

Studies of metals electroprocessing in molten salts

Fluid flow patterns in molten salt electrolytes were observed in order to determine how mass transport affects the morphology of the metal deposit. Studies conducted on the same metal, both in aqueous electrolytes in which coherent solid electrodeposits are produced, as well as in transparent molten salt electrolytes are described. Process variables such as current density and composition of the electrolyte are adjusted to change the morphology of the electrodeposit and, thus, to permit the study of the nature of electrolyte flow in relation to the quality of the electrodeposit.

Sadoway, D. R.↗
NASA NTRS2005

Multilayer Composite Pressure Vessels

A method has been devised to enable the fabrication of lightweight pressure vessels from multilayer composite materials. This method is related to, but not the same as, the method described in gMaking a Metal- Lined Composite-Overwrapped Pressure Vessel h (MFS-31814), NASA Tech Briefs, Vol. 29, No. 3 (March 2005), page 59. The method is flexible in that it poses no major impediment to changes in tank design and is applicable to a wide range of tank sizes. The figure depicts a finished tank fabricated by this method, showing layers added at various stages of the fabrication process. In the first step of the process, a mandrel that defines the size and shape of the interior of the tank is machined from a polyurethane foam or other suitable lightweight tooling material. The mandrel is outfitted with metallic end fittings on a shaft. Each end fitting includes an outer flange that has a small step to accommodate a thin layer of graphite/epoxy or other suitable composite material. The outer surface of the mandrel (but not the fittings) is covered with a suitable release material. The composite material is filament- wound so as to cover the entire surface of the mandrel from the step on one end fitting to the step on the other end fitting. The composite material is then cured in place. The entire workpiece is cut in half in a plane perpendicular to the axis of symmetry at its mid-length point, yielding two composite-material half shells, each containing half of the foam mandrel. The halves of the mandrel are removed from within the composite shells, then the shells are reassembled and bonded together with a belly band of cured composite material. The resulting composite shell becomes a mandrel for the subsequent steps of the fabrication process and remains inside the final tank. The outer surface of the composite shell is covered with a layer of material designed to be impermeable by the pressurized fluid to be contained in the tank. A second step on the outer flange of each end fitting accommodates this layer. Depending on the application, this layer could be, for example, a layer of rubber, a polymer film, or an electrodeposited layer of metal. If the fluid to be contained in the tank is a gas, then the best permeation barrier is electrodeposited metal (typically copper or nickel), which can be effective at a thickness of as little as 0.005 in (.0.13 mm). The electrodeposited metal becomes molecularly bonded to the second step on each metallic end fitting. The permeation-barrier layer is covered with many layers of filament-wound composite material, which could be the same as, or different from, the composite material of the inner shell. Finally, the filament-wound composite material is cured in an ov

DeLay, Tom↗
NASA NTRS1972

Process for the Production of Star Tracklng [Tracking] Reticles

A method for the production of reticles, particularly those for use in outer space, wherein the product is a quartz base coated with highly adherent layers of chromium, chromium-silver, and silver vacuum deposited through a mask, and then coated with an electrodeposit of copper from a copper sulfate solution followed by an electrodeposit of black chromium. The masks are produced by coating a beryllium-copper alloy substrate with a positive working photoresist, developing the photoresist according to a pattern to leave a positive mask, plating uncoated areas with gold, removing the photoresist, coating the substrate with a negative working photoresist, developing the negative working photoresist to expose the base metal of the pattern, and chemically etching the unplated side of the pattern to produce the mask. The mask produced is then used in the vacuum deposition of: (1) chromium metal on the surface of a quartz base to obtain a highly adherent quartz-chromium interface; (2) silver on the chromium deposit, during the final stage of chromium deposit, to produce a silver chromium alloy layer; and (3) silver onto the surface of the alloy layer. The coated quartz base is then coated by electroplating utilizing an acid copper deposit followed by a black chromium electrodeposit to produce the product of the present invention.

Smith, Wade O.↗
DOE OSTI2025

Examples of X-Ray Characterization Techniques in Energy Storage Research

Lithium-ion batteries have revolutionized the portable electronics and transportation sectors. Their performance is often critically dependent on the crystal structures of the anode and cathode electrode materials, which must enable the transport and reversible storage of lithium ions into and out of the lattice. Because lithium is a low-Z element, characterization of materials for lithium-ion batteries can be particularly challenging. Regardless, X-ray techniques enable analysis of material structures to better understand how battery materials perform and degrade, particularly when combined with other materials characterization and electrochemical characterization techniques. While X-ray techniques are most often used in battery research for phase identification of crystal structures, X-ray characterization techniques are also used for a wide variety of other purposes. I will discuss several examples from my research with various collaborators on several projects that highlight the impact that X-ray characterization techniques can have on battery research. The first example will focus on low-temperature microwave-assisted solvothermal synthesis of vanadium-doped LiFePO4 cathode materials for lithium-ion batteries. (1,2) Through a combination of electrochemical and materials characterization, we determined that low temperature synthesis resulted in metastable phases that enabled incorporation of higher dopant levels than resulting from high-temperature synthesis of thermodynamically stable phases. Rietveld refinement of X-ray diffraction data enabled understanding of how lattice parameters changed with doping levels and synthesis temperature. X-ray absorption near edge spectroscopy enabled understanding of the vanadium and iron oxidation states to confirm how vacancies in the structure caused by doping were charge compensated. This was important to understand because the literature suggests doping can improve LiFePO4 electrical conductivity, which improves battery charge and discharge rates. The second example will focus on understanding residual strain in lithium metal anodes. Lithium-ion batteries typically use graphite anodes, but the charge-storage capacity can be theoretically improved ~10x by using lithium metal as the anode material instead. However, lithium anodes suffer from growth of high-aspect-ratio features, such as dendrites, that can pierce nanoporous polymer separators and lead to short circuits and fires. External pressure is commonly applied to cells to enable better morphological control. We hypothesized that applied pressure may promote strain and possibly work hardening during electrochemical cycling, which motivated us to look for evidence of residual strain in lithium metal cycled under applied pressure using X-ray diffraction and sin2(..psi..) analysis. We found that lithium electrodeposited under high pressure exhibited in-plane compressive strain and that that lithium electrodeposited under low pressure did not. (3) The residual strain that accompanies electrodeposition under high pressure may lead to work hardening, which may explain how a soft metal like lithium can puncture separators and why higher pressure does not always decrease short circuits. (4-6) References: 1) Harrison, K. L.; Manthiram, A. Microwave-Assisted Solvothermal Synthesis and Characterization of Metastable LiFe1- x (VO) x PO4 Cathodes. Inorganic chemistry 2011, 50(8), 3613-3620. 2) Harrison, K. L.; Bridges, C. A.; Paranthaman, M. P.; Segre, C. U.; Katsoudas, J.; Maroni, V. A.; Idrobo, J. C.; Goodenough, J. B.; Manthiram, A. Temperature Dependence of Aliovalent-Vanadium Doping in LiFePO4 Cathodes. Chemistry of Materials 2013, 25(5), 768-781. 3) Rodriguez, M. A.; Harrison, K. L.; Goriparti, S.; Griego, J. J.; Boyce, B. L.; Perdue, B. R. Use of a Be-Dome Holder for Texture and Strain Characterization of Li Metal Thin Films via Sin2 (..psi..) Methodology. Powder Diffraction 2020, 35(2), 89-97. 4) Jungjohann, K. L.; Gannon, R. N.; Goriparti, S.; Randolph, S. J.; Merrill, L. C.; Johnson, D. C.; Zavadil, K. R.; Harris, S. J.; Harrison, K. L. Cryogenic Laser Ablation Reveals Short-Circuit Mechanism in Lithium Metal Batteries. ACS Energy Letters 2021, 6(6), 2138-2144. 5) Harrison, K. L.; Merrill, L. C.; Long, D. M.; Randolph, S. J.; Goriparti, S.; Christian, J.; Warren, B.; Roberts, S. A.; Harris, S. J.; Perry, D. L. Cryogenic Electron Microscopy Reveals That Applied Pressure Promotes Short Circuits in Li Batteries. Iscience 2021, 24(12). 6) Harrison, K. L.; Goriparti, S.; Merrill, L. C.; Long, D. M.; Warren, B.; Roberts, S. A.; Perdue, B. R.; Casias, Z.; Cuillier, P.; Boyce, B. L. Effects of Applied Interfacial Pressure on Li-Metal Cycling Performance and Morphology in 4 M LiFSI in DME. ACS Applied Materials & Interfaces 2021, 13(27), 31668-31679.

batteries↗
DOE OSTI2025

Achieving Electrode Smoothing by Controlling the Nucleation Phase of Metal Deposition Through Polymer‐Substrate Binding

Polymer additives [like polyethylene oxide (PEO)] are widely used for smooth electrode deposition in aqueous zinc and many other battery systems. However, the precise mechanism by which they regulate morphology and suppress dendrite formation remains unclear. In this study, the knowledge gap is addressed by using in situ electrochemical atomic force microscopy to directly observe the interfacial evolution during Zn electrodeposition and polymer adsorption on Cu substrates in the presence of varying concentrations of ZnSO 4 and PEO. Contrary to previous literature assumptions, which emphasize the binding to the growing Zn crystal surfaces or Zn 2+ ions, the results demonstrate that PEO smooths Zn films by promoting nucleation of (002)-oriented Zn platelets through interactions with the Cu substrate. Density functional theory simulations support this finding by showing that PEO adsorption on Cu modifies the interfacial energy of Zn/Cu/electrolyte interfaces, favoring the stabilization of Zn (002) on the Cu substrate, as well as confines Zn electrodeposition to a narrow near-surface region. In conclusion, these findings elucidate a novel design principle for electrode smoothing, emphasizing the importance of substrate selection paired with polymer additives that exhibit an attractive interaction with the substrate but minimal interaction with growing crystals, offering a mechanistic perspective for improved battery performance.

Electrodeposition↗
DOE OSTI2016

Photoluminescent properties of electrochemically synthetized ZnO nanotubes

ZnO nanotubes were prepared by a sequential combination of electrochemical deposition, chemical attack and regeneration. ZnO nanocolumns were initially electrodeposited on conductive substrates and then converted into nanotubes by a process involving chemical etching and subsequent regrowth. The morphology of these ZnO nanocolumns and derived nanotubes was monitored by Scanning Electron Microscopy and their optical properties was studied by photoluminescence spectroscopy. Photoluminescence were measured as a function of temperature, from 6 to 300 K, for both nanocolumns and nanotubes. In order to study the behaviour of induced intrinsic defect all ZnO films were annealed in air at 400 °C and their photoluminescent properties were also registered before and after annealing. The behaviour of photoluminescence is explained taking into account the contribution of different point defects. A band energy diagram related to intrinsic defects was proposed to describe the behaviour of photoluminescence spectra. - Highlights: •ZnO nanotubes were obtained after etching and regrowth of electrodeposited ZnO films. •Photoluminescence spectra contain two parts involving excitonic and defects transitions. •Annealing produces a blue shift in the PL peaks in both ZnO nanocolumns and nanotubes. •Etching causes a blue shift in PL peaks due to confinement effect in nanotubes walls.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Synthesis, characterization and electrochemical studies of nanostructured CaWO{sub 4} as platinum support for oxygen reduction reaction

Highlights: • Nanostructured CaWO{sub 4} was fabricated by co-precipitation method. • Platinum was electrodeposited onto the surface prepared nanostructured CaWO{sub 4}. • Pt/CaWO{sub 4}-graphite demonstrate good oxygen reduction reaction activity. - Abstract: In the present work, we employed nanostructured calcium tungstate as a supporting material for platinum, a well-known electrocatalyst for oxygen reduction. The co-precipitation method has been utilized to synthesize nanostructured calcium tungstate from aqueous solution. The structure and morphology of the obtained CaWO{sub 4} were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Preparation of the Pt/CaWO{sub 4}-graphite catalyst was carried out by electrodeposition of Pt onto the surface of CaWO{sub 4}/graphite electrode. The physical properties of the catalyst were determined by scanning electron microscopy analysis and energy dispersive X-ray (SEM/EDX). The electrochemical activity of the Pt/CaWO{sub 4}-graphite for the oxygen reduction reaction (ORR) was investigated in acid solution by cyclic voltammetry measurements, linear sweep voltammetry, and electrochemical impedance spectroscopy. The results revealed that the Pt/CaWO{sub 4}-graphite has higher electrocatalytic activity for oxygen reduction in comparison with Pt/graphite catalyst.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Nanocomposite film of TiO{sub 2} nanotube and polyoxometalate towards photocatalytic degradation of nitrobenzene

Highlights: • The film of POMs and TiO{sub 2} nanotubes was prepared by electrodeposition. • The photocatalytic activity of the composite film for nitrobenzene was investigated. • The composite film showed higher photocatalytic activity than pure TiO{sub 2} nanotubes. • The introduction of POMs into TiO{sub 2} could retard electron–hole recombination. - Abstract: The composite film based on polyoxometalates (POMs)-modified TiO{sub 2} nanotubes was prepared by electrodeposition method for the photocatalytic degradation of nitrobenzene. The composite film was characterized by field-emission scanning electron microscopy, X-ray diffraction, energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, which indicated that the POMs were well introduced into the TiO{sub 2} nanotubes. Furthermore, the photocatalytic properties of the TiO{sub 2} nanotubes and POMs-modified TiO{sub 2} nanotubes were evaluated by the decomposition of nitrobenzene. POMs-modified TiO{sub 2} nanotubes showed much higher photocatalytic activity than pure TiO{sub 2} nanotubes. These results provide a promising route to effectively photocatalytic degradation of nitrobenzene by POMs-modified TiO{sub 2} nanotubes.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Self-supported porous CoO semisphere arrays as binder-free electrodes for high-performance lithium ion batteries

Highlights: • CoO semisphere arrays are prepared by a template-assisted electrodeposition method. • Interconnected semisphere arrays are favorable for fast ion/electron transfer. • CoO semisphere arrays show excellent Li ion storage performance. - Abstract: Construction of hierarchical porous metal oxides arrays is critical for the development of high-performance electrochemical energy storage devices. Herein we report porous CoO semisphere arrays using an electrodeposited polystyrene template method. Interestingly, the as-prepared porous CoO semisphere arrays consist of bowl-like semispheres with diameters of ∼500 nm and show highly porous structure. As a preliminary test as anode for lithium ion batteries (LIBs), the porous CoO semispheres arrays exhibit superior electrochemical performances with good cyclability (695.5 mAh g{sup −1} after 150 cycles at 0.5 A g{sup −1}) and high-rate capability. The porous semispherical architecture provides positive roles in the enhancement of electrochemical properties, including fast electronic transportation path, short diffusion of Li ion and high sufficient interfacial contact area between the active material and the electrolyte. The developed methodology enables a new fabrication of porous metal oxides with applications in electro-catalysis, optical and electrochemical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A new method for the fabrication of a bilayer WO3/Fe2O3 photoelectrode for enhanced photoelectrochemical performance

Highlights: • A thin layer of Fe{sub 2}O{sub 3} is layered on the electrodeposited WO{sub 3} photoelectrode. • The light absorption of WO{sub 3} was extended towards the visible light region, resulting higher photoelctrochemical performance. • Charge transfer mechanism in the bilayer photoanode was suggested. - Abstract: A bilayer WO{sub 3}/Fe{sub 2}O{sub 3} heterojunction photoelectrode was prepared with a new approach for photoelectrochemical reactions. WO{sub 3} was deposited onto an FTO conductive glass substrate via electrodeposition, followed by the deposition of an ultrathin Fe{sub 2}O{sub 3} layer using the chemical bath deposition method. The presence of Fe{sub 2}O{sub 3} layer improved the light absorption of WO{sub 3}/Fe{sub 2}O{sub 3} toward visible light region (red-shift). The addition of a thin layer of Fe{sub 2}O{sub 3} on WO{sub 3} resulted in higher photocatalytic performance (two-fold improvement) compared to that of pristine WO{sub 3}. In addition, the WO{sub 3}/Fe{sub 2}O{sub 3} photoelectrode also showed a positive photoresponse for methanol degradation. The photocurrent generation of the bilayer photoelectrode improved 1.6-fold with the addition of methanol as a sacrificial donor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Potential of electrolytic processes for recovery of molybdenum from molten salts for 99 Mo production

Molten salt reactor (MSR) technologies are receiving significant interest for commercialization because of their potential safety features and efficient energy production. In addition to producing reliable and clean energy, high-value radioisotopes could be harvested from MSRs as an additional revenue stream. Although significant quantities of 99 Mo will be produced in MSRs through fission, how accessible 99 Mo will be for direct recovery from a fuel salt is unclear. Electrolytic processes in fused salts have been used extensively for processing molten salts and have the potential to enable the extraction of 99 Mo directly from the fuel salt. This paper reviews the behavior of 99 Mo in the molten salt reactor experiment and summarizes theoretical aspects of the electrolytic process in high-temperature fused salt and the published experimental results on Mo extraction through electrolytic processes. Here, the general principle of fused-salt electrolytic processes is described, by electrodeposition of Mo with the following aspects: electrowinning, electrorefining, electroplating, and electroextraction with several experimental considerations. Finally, important considerations for recovery of 99 Mo from MSR relevant molten salts via electrodeposition are discussed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2015

Eco-friendly copper recovery process from waste printed circuit boards using Fe{sup 3+}/Fe{sup 2+} redox system

Highlights: • We developed an ecofriendly mediated electrochemical process for copper recovery. • The recovery of copper was achieved without mechanical pretreatment of the samples. • We identified the optimal flow rate for the leaching and electrowinning of copper. • The copper content of the obtained cathodic deposits was over 99.9%. - Abstract: The present study aimed at developing an original and environmentally friendly process for the recovery of copper from waste printed circuit boards (WPCBs) by chemical dissolution with Fe{sup 3+} combined with the simultaneous electrowinning of copper and oxidant regeneration. The recovery of copper was achieved in an original set-up consisting of a three chamber electrochemical reactor (ER) connected in series with a chemical reactor (CR) equipped with a perforated rotating drum. Several experiments were performed in order to identify the optimal flow rate for the dissolution of copper in the CR and to ensure the lowest energy consumption for copper electrodeposition in the ER. The optimal hydrodynamic conditions were provided at 400 mL/min, leading to the 75% dissolution of metals and to a low specific energy consumption of 1.59 kW h/kg Cu for the electrodeposition process. In most experiments, the copper content of the obtained cathodic deposits was over 99.9%.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2014

Field emission properties of ZnO nanosheet arrays

Electron emission properties of electrodeposited ZnO nanosheet arrays grown on Indium tin oxide coated glass substrates have been studied. Influence of oxygen vacancies on electronic structures and field emission properties of ZnO nanosheets are investigated using density functional theory. The oxygen vacancies produce unshared d electrons which form an impurity energy state; this causes shifting of Fermi level towards the vacuum, and so the barrier energy for electron extraction reduces. The ZnO nanosheet arrays exhibit a low turn-on field of 2.4 V/μm at 0.1 μA/cm{sup 2} and current density of 50.1 μA/cm{sup 2} at an applied field of 6.4 V/μm with field enhancement factor, β = 5812 and good field emission current stability. The nanosheet arrays grown by a facile electrodeposition process have great potential as robust high performance vertical structure electron emitters for future flat panel displays and vacuum electronic device applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Patterned arrays of capped platinum nanowires with quasi-elastic mechanical response to lateral force

In this Letter, we describe the electrodeposition of capped, micro-sized Pt nanowire arrays in ion-track etched polymer templates and measure their collective mechanical response to an external force. By using an aperture mask during the irradiation process, it was possible to restrict the creation of pores in the templates to defined areas, allowing the fabrication of small nanowire arrays in different geometries and sizes. The simultaneous and highly reliable formation of many nanowire arrays was achieved using a pulsed electrodeposition technique. After deposition, the polymer matrix was removed using a gentle, dry oxygen plasma treatment, resulting in an excellent preservation of the array nanostructure as confirmed by scanning electron microscopy. A force measuring station was set up to perform mechanical characterization series on free-standing arrays. The nanowire arrays show a high robustness and respond sensitively to the applied force, making them attractive as spring elements in miniaturized inertial sensors, for example.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

22.5% efficient silicon heterojunction solar cell with molybdenum oxide hole collector

Substituting the doped amorphous silicon films at the front of silicon heterojunction solar cells with wide-bandgap transition metal oxides can mitigate parasitic light absorption losses. This was recently proven by replacing p-type amorphous silicon with molybdenum oxide films. In this article, we evidence that annealing above 130 °C—often needed for the curing of printed metal contacts—detrimentally impacts hole collection of such devices. We circumvent this issue by using electrodeposited copper front metallization and demonstrate a silicon heterojunction solar cell with molybdenum oxide hole collector, featuring a fill factor value higher than 80% and certified energy conversion efficiency of 22.5%.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Structural, morphological and Raman studies of pulse electrosynthesised indium antimonide thin films

InSb films deposited on fluorine doped tin oxide (FTO) substrates by a pulse elctrodeposition technique. The deposition was carried out at an applied potential −1.3V versus Ag/AgCl electrode. Structural, morphological and optical studies were performed on the electrodeposited InSb. X-ray diffraction (XRD) studies show that the deposited InSb films are polycrystalline in nature having the zinc blend structure. The crystallite size (D), dislocation density (δ) and strain (ε) were calculated using XRD results. The EDAX analysis shows that chemical composition of In{sup 3+} and Sb{sup 3+} ions is close to the required stoichiometry. The surface morphology of the deposited films was examined using scanning electron microscopy (SEM). SEM studies reveal that the surface of the films is uniformly covered with submicron sized spherical particles. However, the crystallite size determined by the Scherrer method shows a size close to 30 nm. Surface morphology studies of the InSb films were also performed using atomic force microscopy (AFM). The average surface roughness as measured by AFM is around 40 nm. Hot probe studies show that all the electrodeposited thin films have n type conductivity and the thickness of the films is calculated using electrochemical formula.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Electrochemical synthesis of p-Cu{sub 2}O/n-ZnO nanorods hetero-junction for photovoltaic application

Development of high performance visible light responsive solar cell materials has attracted wide interest due to their potential applications in the energy industries. In this work, ZnO nanorods films were successfully prepared on the ITO coated glass substrates via simple three electrode electrochemical deposition route. The Cu{sub 2}O nanoparticles were then electrodeposited on the surface of ZnO nanorods to form p-Cu{sub 2}O/n-ZnO core-shell hetero-structure. The synthesized ZnO, Cu{sub 2}O films and p-Cu{sub 2}O/n-ZnO hetero-structure were characterized by low angle x-ray diffraction, scanning electron microscopy, and UV-Visible spectrophotometer. Due to the hierarchical morphologies and core-shell structure, p-Cu{sub 2}O/n-ZnO hetero-structure shows a prominent visible-light-driven photocatalytic performance under the low intensity light irradiation. The obtained results suggest that it is possible to synthesize ZnO nanorods, Cu{sub 2}O films and p-Cu{sub 2}O/n-ZnO core-shell hetero-structure by a simple, cost effective and environment friendly electrodeposition process which can be useful for water splitting and solar cell device fabrication.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗